IP Indoor High Speed Dome CAM-6510 Ver.
0 0 1. 2. PRECAUTIONS Read these instructions All the safety and operating instructions should be read before the product is operated. Heed all warnings All warnings on the product and in the instruction manual should be adhered to. The symbol indicates the following items, please carefully read the description next to each symbol. a. Failure to follow the safety instruction given may directly endanger people, cause damage to the system or to other equipment. b.
typographical or technical errors and reserve the right to make changes to the product and manuals without prior notice. FCC/CE Regulation NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Table of Contents 0 PRECAUTIONS________________________________________________ 0-1 Copyright __________________________________________________________________ 0-1 Trademarks ________________________________________________________________ 0-1 Liability ___________________________________________________________________ 0-1 FCC/CE Regulation __________________________________________________________ 0-2 1 INTRODUCTION ________________________________________________1 1.
B-3: Configuration Menu_______________________________________________________40 B-3-1 DEFAULT CAMERA __________________________________________________40 B-3-2 BACKLIGHT ________________________________________________________40 B-3-3 FOCUS _____________________________________________________________41 B-3-4 APERTURE _________________________________________________________41 B-3-5 AE MODE ___________________________________________________________42 B-3-6 WBC MODE _____________________________
11 1.1 INTRODUCTION Package Contents CAM-6500 series Product CD LAN/WAN Cable 5.
1.2 Features and Benefits The IP High Speed Dome is designed to deliver superb performance and durability with an intelligent and stylish housing. It also provides a realiable real time images with outstanding image quality (D1, 720x480) at reasonable bandwidth through a standard TCP/IP network. That’s because it is Ethernet (LAN and WAN) ready and has a powerful ARM9 SoC and the MPEG-4 compression ASIC inside.
Privacy Mask for Privacy Protection There is up to 24 privacy zones of camera view programmable. This is specially designed to avoid any intrusive monitoring at specific region. Real-time MPEG-4 Compression With hardware MPEG-4 compression chip inside, the composite video inputs can be efficiently compressed into MPEG-4 bit stream without any delay. The ASIC base compression engine can support not only CIF, but also FULL D1 image resolution.
No more external motion sensors are required. Each IP high speed dome can be set up to 3 detection areas. By tuning the object size and sensitivity, it is very reliable to fit into your environment. Besides, hardware motion detection delivers better sensitivity and respond faster than software motion detection. Bundle Powerful Surveillance Software To extend the capabilities of the IP high speed dome, a powerful surveillance program is included in the package and is totally free to use.
This device is likely to be damaged or damage other equipments / personnel, if you use a power supply with different voltage than the one included with this device. All warranty of this product will be voided in the situations above. Don’t open the housing of the product Cleaning Disconnect this video product from the power supply before cleaning. Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards.
Safety Check Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine that the video product is in proper operating condition. 1.
1. Reset Button Step 1: Switch off IP device by disconnecting the power cable Step 2: Press and continue to hold the Reset Button. Reconnect the power cable while continuing to hold the reset button. Step 3: Keep holding the reset button depressed around 6 seconds, release the reset button. The unit will start up with factory default settings. 2. Communication Switch Setting The table below shows the function of each pin within the Communication Switch.
arrow to the desired number respectively. For instance, if the speed dome ID is 123, the ID switch should be set as below: centesimal decimal single digit NOTE: If controlling through an ACTi decoder via analog means such as a keyboard or DVR, no two speed domes should be given the same ID or communication conflict may occur. When controlled only through Ethernet and software D (without the use of an ACTi hardware decoder), the dome ID o setting may be neglected.
decimal single digit 5. 16 Pin Connector for LAN/WAN The LAN/WAN cable (shown as the figure below) is shipped with IP high speed dome. Please find it in the accessory bag. 6. 22 Pin Connector A 50cm data cable (shown as the figure below) is shipped with IP high speed dome. Please find it in the accessory bag. Power Input PIN 1 2 3 NAME DESCRIPTION AC24V AC 24V of Power Input E-GND E-Ground Pin of Power Input AC24V AC 24V of Power Input 7.
The alarm pins are serviceable for connecting alarm input and output devices, such as alarm sensors, sirens or flashing light with the surveillance system. The table shown as follows lists the definition of alarm pins on the 22-pin connector.
11
1.5 Mounting the IP High Speed Dome Generally, there are three kinds of ceiling mounting methods: surface mount, in-ceiling mount, and mounting with straight tube. The surface mounting kit is shipped with IP high speed dome. For more detailed information, please refer to Appendix A.
1.6 Basic Connections Follow the procedures below to connect the IP high speed dome to the respective apparatuses.
Appendix A: Speed Dome Installation Basing on user’s installation environments, the dome can be installed on ceiling, on wall or on pole. In the following section, various indoor speed dome installation accessories, installation methods and installation procedures will be described in detail. A-1: Optional Accessories Surface Ceiling Mount For Surface Ceiling use. Height: 21.4mm ; Diameter of the three holes: 4.5mm ; Diameter of the bracket: 158mm In-Ceiling Mount For in-ceiling Installation use.
Ceiling Panel For ceiling mounting. Zn platted; 610×305 mm (24×12 inches); Diameter: 155 mm (6.1 inches) Transparent Cover/Smoke Cover Diameter: 137 mm (5.4 inches); 127 mm (5.0 inches) 5’’ Transparent Cover 5.4’’ Transparent Cover 5’’ Smoke Cover 5.4’’ Smoke Cover Indoor Mount Kit White; Diameter: 140 mm (5.5 inches); Height: 74 mm (2.9 inches) For mounting indoor dome camera onto a gooseneck/straight tube.
Mounting Accessories Gooseneck Tube White/Iron; 298×385 mm (11.73×15.56 inches) ; 2.1 kg (4.6 lbs) Supplied with rubber washer-8×1, pendant tube washer×1, spring washer-8×1 and waterproof rubber×1, M8*12 screw×1. Straight Tube White/Iron; Height: 250/500 mm (9.8/19.7 inches); Diameter: 50 mm (2 inches) 1 kg (2.2 lbs) / 1.8 kg (4 lbs). Supplied with rubber washer-8×1, pendant tube washer×1, spring washer-8×1 and waterproof rubber×1, M8*12 screw×1.
washer-8×4, spring washer×4, M8*20 screw×4, M8 nut×4. Pole Thin Direct Mounting White/Ivory; 232(L)×136(W)×60(D) mm (9.1×5.4×2.4 inches); Diameter: 112~140 mm (4.4~5.5 inches); 0.7 kg (1.6 lbs). Supplied with stainless steel straps×4, M8*16 screw×4, washer×4. Pole Wide Direct Mounting White/Ivory; 270(L)×170(W)×60(D) mm (10.6×6.7×2.4 inches); Diameter: 112~130 mm (4.4~5 inches); 1 kg (2.2 lbs).
Corner Thin Box White/Ivory, 300(L)×164(W)×222(D) mm (11.8×6.5×8.7 inches); 3 kg (6.7 lbs); Supplied with washer×4, M8*16 screw×4 and spring washer×4. Corner Wide Box White/Ivory; 232(L)×234(W)×210(D) mm (9.1×9.2×8.3 inches); 2.7 kg (6 lbs); Supplied with washer×4, M8*16 screw×4 and spring washer×4.
Pole Thin Box White/Ivory; 291(L)×136(W)×245(D) mm (11.5×5.3×9.5 inches); 3.1 kg (6.9 lbs); Supplied with M8*16 screw×4, washer×4, spring washer×4, stainless steel straps×4. Pole Wide Box White/Ivory, 270(L)×166(W)×155(D) mm (10.6×6.5×6.1 inches); 3.2 kg (7.1 lbs); Supplied with M8*16 screw×4, washer×4, spring washer×4, stainless steel straps×4. Wall Box Mounting Ivory, 270(L)×166(W)×95(D) (10.6×6.5×3.7 inches); 2.2 kg (4.
Stainless Steel Straps For fixing Pole Direct Mounting/ Pole Box on the pole. Width: 0.63”; 0.02 kg (0.04 lbs) Stainless Strap Cutter For tension, cut and crimp stainless steel straps. 1.4 kg (3.
D77R1 D77R2 D77R3 Connector Box (Indoor Application) Recommended for wiring indoor dome alarm cables. White Color. 92×42 mm (3.7×1.7 inches); 0.13 kg (0.3 lbs); Supplied with cable×1, bracket×1 and M3*6 screw×2. Power Box White; 186.5×147 mm (7.3×5.8 inches); 2.6 kg (5.
A-2: Ceiling Mount Generally, there are three kinds of speed dome camera ceiling mounting methods: surface mount, in-ceiling mount, and mounting with straight tube. Refer to the following sections for more detailed information. The following figures show how cables connect to the speed dome camera in different ways.
A-3: Surface Ceiling Mounting Surface Ceiling Mounting is a standard installation for an indoor dome, and general mounting accessories are equipped in the standard indoor dome camera package. Here lists the items and tools needed to mount the dome camera onto the ceilings. The supplied items are all in the speed dome camera package.
STEP 3 Attach the Mount to the ceiling. Mark the locations where all three ceiling holes should go. STEP 4 Drill these holes on the surface ceiling. STEP 5 Fix the Mount to the holes on the surface ceiling with three screws. STEP 6 Thread the data cable through the center hole of the Mount and connect the cable to the dome body.
STEP 7 Attach the dome body to the Mount and rotate the dome clockwise. Tighten the fixing screw to fix the dome body. STEP 8 Fix the decoration ring to the bracket and then place the optical cover. A-4: Ceiling Panel for In-ceiling Mounting To mount the speed dome camera to a suspended ceiling with the T-Bar, the ceiling panel could be employed, as shown in the figure below. Follow the steps below for installing the ceiling panel.
A-5: In-ceiling Mounting Here lists the items and tools needed to mount the dome camera into the ceilings. The supplied items are all in the dome camera package.
Step 2: Attach the separated wing to the dome, as shown in the diagram. STEP 3 Place the Red Sticker on the ceiling plate, and cut the circle part out of the ceiling. STEP 4 Put up the T-Bar into the ceiling hole. STEP 5 Rotate T-Bar wings of the hinge to fix the T-Bar at the edge of the ceiling hole.
STEP 6 Tighten the screws, and the T-Bar wings will adhere to the ceiling. STEP 7 Put the 22-pin data cable through the center hole of the T-bar and connect it to the dome body. STEP 8 Mount the dome body to the Bracket and rotate it clockwise. Tighten the fixing screw to fix the dome body. STEP 9 Fix the decoration ring to the bracket and then place the optical cover.
A-6: Ceiling Mount with Straight Tube The straight tube is available in different length: 25cm and 50cm. Follow the steps to mount the speed with the straight tube. (1) Ensure that the ceiling can support the weight of the speed dome camera and straight tube.
A-7: Wall Mount A-7-1 Wall Mounting with Gooseneck Tble The following figures show how cables run through the tube in different ways. Cables exposed Cables recessed Follow the steps to mount the speed dome with the gooseneck tube. (1) Make a cable entry hole on the wall to recess the cables. Otherwise, cables can be threaded through the cable entry hole on the tube.
A-7-2 Wall Box Mounting Follow the steps to mount the dome with the wall box and gooseneck tube. 1) Fix the wall box to wall. 2) Fasten the gooseneck tube on the wall box. 3) Thread the cables through the gooseneck tube and the Indoor Mount Kit and connect them to the dome camera. For installation of the cables, Indoor Mount kit and the dome camera unit, refer to A-7-1 as the steps are the same as for gooseneck mounting.
A-8: Corner Mount A-8-1 Corner Standard Mounting Plate With the corner mounting plate and gooseneck, the dome can be mounted on wall. There are various types of corner mounting accessories with different width. 1) Make a cable entry hole on the wall to recess the cables.
A-8-2 Corner Thin/Wide Box Mounting The thin/wide corner box is designed to be installed with a gooseneck tube. Follow the steps to mount the dome camera with the corner box and gooseneck tube. 1) Make a cable entry hole on the wall to recess the cables.
A-9: Pole Mount A-9-1 Pole Thin/Wide Direct Mounting The dome can be installed on a pole with a thin or wide pole mounting accessory and a gooseneck. 1) Fasten the suspension mounting plate on a pole with equipped stainless straps 2) Fix the gooseneck tube on the pole mounting plate 3) Thread the cables through the gooseneck tube and the Indoor Mount kit and connect them to the speed dome camera 4) Fix the Indoor Mount kit to the gooseneck tube using the screws and washers.
A-9-2 Pole Thin/Wide Box Mounting Follow the steps to mount the PTZ camera with the pole box and gooseneck tube. 1) Fasten the pole box on a pole with equipped stainless straps 2) Fix the gooseneck tube to the pole box 3) Thread the cables through the gooseneck tube and the top holder and connect them to the PTZ camera 4) Fix the top holder to the gooseneck tube using the screws and washers. 5) Attache the PTZ camera to the top holder and fix them with the screw.
Appendix B: OSD Menu Notes B-1: OSD Display Format The information shown on the screen are described in terms of OSD display, position and function description in the table below.
Item Layer 1 Layer 2 Layer 3 Default CAMERA BACKLIGHT , AUTO AF Mode , , FOCUS AE MODE OFF MANUAL Focus Manual Speed <01>~<08> AUTO Exposure Comp. , <1>~<15> BRIGHT Bright <0> ~ <31> SHUTTER Shutter Speed <1> ~ <1/10000> Sec. GAIN Gain <-3> ~ <28>dB IRIS Iris ,
Item Layer 1 Layer 2 Layer 3 Default SETTNG ALARM SWITCH , OFF ALARM TYPE (Normal Open), (Normal N.C. Close) ALARM ACTION PRESET SEQUENCE AUTOPAN CRUISE PRESET POINT <001> ~ <256> SEQUENCE LINE <1> ~ <8> AUTOPAN LINE <1> ~ <4> CRUISE LINE <1> DWELL TIME <001> ~ <127> Sec., EXIT YES HOME FUNC.
Item Layer 1 Layer 2 Layer 3 END POINT , DIRECTION , SPEED <01> ~ <04> Default Right 01 RUN AUTOPAN EXIT RECORD START RECORD END CRUISE RUN CRUISE EXIT IR FUNCTION (F/U model , Auto only) ALARM DETECT SWITCH , DETECT MODE , ,
Item Layer 1 EXIT OSD YES Layer 2 Layer 3 Default B-3: Configuration Menu The detailed functions and parameter settings of your high speed dome can be set by the OSD (On Screen Display) menu with a control program. The functions in OSD menu are described in the following sections. 18x MODEL MAIN PAGE 1 DEFAULT CAMERA BACKLIGHT FOCUS AE MODE WBC MODE ID DISPLAY SETUP MENU1 SETUP MENU2 OFF OFF AUTO AUTO AUTO ON B-3-1 DEFAULT CAMERA The “DEFAULT CAMERA” is used to restore the camera settings (e.g.
B-3-3 FOCUS Automatically adjusts the focus position to maximize the high frequency content of the picture in a center measurement area, taking into consideration the high luminance and strong contrast components. The focus of the dome camera can be operated in two modes: Manual Focus mode and Auto Focus mode. Different settings for various models are described as follows. ¾ ♦ 18x MODEL AUTO The optimum focus is achieved by the internal digital circuit.
♦ AUTO The dome camera will assign a proper aperture value automatically for camera to achieve a better image. ♦ MANUAL Select this item if you want to adjust aperture value manually. Higher value enhances the incident ray of camera. APERTURE MENU H APERTURE 15 V APERTURE 15 NOTE: For 18x MODEL, please refer to section B-1-9 SETUP MENU2 for information on Aperture function.
The brightness control function adjusts IRIS and AGC gain using an internal algorithm. The brightness is controlled by gain when the light condition is dark and by iris when the light condition is bright. ♦ SHUTTER With this option, the SHUTTER speed takes main control of the exposure, and both IRIS and AGC will function automatically in cooperation with shutter speed to achieve consistent exposure output.
¾ ♦ 18x MODEL AUTO In this mode, white balance works within its colour temperature range. This mode computes the white balance value output using colour information from the entire screen. It outputs the proper value using the colour temperature radiating from a black subject based on a range of values from 3000K to 7500K. ♦ INDOOR 3200K Base mode ♦ OUTDOOR 5800K Base mode ♦ ATW Auto Tracing White Balance mode. The dome taking out the signals in a screen in the range from 2000K to 10000K.
B-3-8 SETUP MENU Users can adjust camera lens model parameters under SETUP MENUs. Depending on the model of dome cameras, the SETUP MENUs are different. 18x MODEL SETUP MENU1 FLIP ZOOM SPEED SPEED BY ZOOM AUTO CALI. DIGITAL ZOOM SLOW SHUTTER ANGLE ADJUSTER RESET EXIT ♦ ENTER 1 OFF OFF 12 OFF ENTER YES YES SETUP MENU2 APERTURE MASK DISPLAY 01 FIRST FLIP (IMAGE/ME/OFF) User can track an object continuously when it passes through under dome camera with setting Flip to IMAGE (digital flip) or M.E.
Select this item to disable the flip function. NOTE: The speed dome will only be able to tilt 90°, or -10° ~ 100° with angle adjuster adjustments. ♦ ZOOM SPEED This item is used to set the zoom speed for operating the dome camera. ¾ 18x MODEL For this model, the zoom speed options are <1> (slow) ~ <8> (fast). The default is <8> ♦ SPEED BY ZOOM If the item is set to , the pan/tilt speed will be adjusted by internal algorithm when zooming automatically.
The default setting is ♦ SLOW SHUTTER The shutter speed determines how long the image sensor is exposed to light. To see clear image in a dark environment, enable this function and select a slower shutter speed. ¾ 18x MODEL As enable this digital slow shutter function, the dome will automatically adjust the shutter speed basing on the light condition of installation environment. It enables users to see objects in a dark environment under 0.2 lux.
SETUP MENU2 APERTURE MASK DISPLAY 01 FIRST ♦ APERTURE Under this setup menu, users can adjust the enhancement of the edges of objects in the picture. There are 16 levels of adjustment; the options are <01) ~ <16>, <01> represents “no enhancement”. When shooting text, this function may help by making them sharper. ♦ MASK DISPLAY In this item, users can set the occasion to display the Privacy Mask, which aims to avoid any intrusive monitoring.
♦ OFF When the TITLE DISPLAY is set , no title will be displayed on the screen even titles are set in advance. B-3-11 TITLE SETTING Up to 16 zone titles can be set with maximum 20 characters for each title; two mask zones are allowed to set in a view area. Users can name the zone titles with privacy mask ID numbers for future recognition. Follow the steps to set a camera title. (1) (2) (3) (4) Operate speed dome to certain view area where you want to set a title for it.
be set on this page. ALARM SETTING ALARM PIN ALARM SWITCH ALARM TYPE ALARM ACTION PRESET PRESET POINT DWELL TIME 1 OFF N.C. 001 ALWAY ♦ ALARM PIN The dome provides 8 alarm inputs and 2 outputs ( 1 x N.O. and 1 x N.C.). Select an alarm connector which you want to set its alarm-related parameters with this item, and then set its alarm-related parameters in Alarm Setting menu. ♦ ALARM SWITCH The item is used to enable or disable the selected alarm pin function.
Select a preset point where the dome should go when an alarm pin is triggered. SEQUENCE Select a sequence line that the speed dome camer should execute when alarm pin is triggered. The Sequence line should be defined prior in SEQENCE setup menu. AUTOPAN Select an auto-pan line that the dome camera should execute when alarm pin is triggered. The Auto-pan line can be defined in setup AUTOPAN menu. CRUISE Select a cruise line that the speed dome camera should execute when alarm pin is triggered.
♦ HOME FUNCTION The item is used to enable or disable the HOME function. ♦ SELECT MODE Select one of the modes that the dome should execute when HOME function is enabled and the RETURN TIME is up. The options are , , and . ♦ PRESET Select a preset point where the speed dome should go when alarm pin is triggered. SEQUENCE Select a sequence line that the speed dome camer should execute when alarm pin is triggered.
B-3-14 SEQENCE The function executes pre-positioning of the pan, tilt, zoom and focus features in a certain sequence for a camera. Before set up this function, users must setup at least two preset points. SEQUENCE SEQUENCE LINE SEQUENCE POINT PRESET POSITION SPEED DWELL TIME RUN SEQUENCE EXIT ♦ 1 01 001 1 001 ENTER YES SEQUENCE LINE There are eight sets of sequence lines built in the speed dome camera. Using LEFT/RIGHT direction keys to select a line first and then set its sequence points.
Speed 6 Speed 7 Speed 8 Speed 9 Speed 10 Speed 11 Speed 12 Speed 13 Speed 14 Speed 15 65 75 185 205 225 250 280 320 365 400 50 58 185 210 240 275 305 335 365 400 ♦ DWELL TIME The DWELL TIME is the duration time that the speed dome will stay at the sequence point, and the range is from <0> to <127> seconds. The speed dome will go to the next sequence point when the DWELL TIME is up. If the setting is <0>, the speed dome will stay at this sequence point until users manually move the speed dome.
There are four sets of auto-pan lines built in speed dome camera. Users are able to command the speed dome camera to do continuously panning without limit by setting the start point the same as endpoint. ♦ START POINT Follow the description to set the start position of the AUTOPAN path. 1. Move the cursor to and press while item flashes, the item will turn automatically. 2.
auto-pan. The speed is adjustable from 1 to 4; refer to the table below for details. Speed 1 Speed 2 Speed 3 Speed 4 PAN (degree/sec.) 10 23 35 45 ♦ RUN AUTOPAN After the setting is completed, select this item to manually execute the Auto-pan function. ♦ EXIT Exit the AUTOPAN setup menu. B-3-16 CRUISE A Cruise is a route of manual operations that can be stored and recalled to execute repeatedly.
♦ RECORD END The cursor will be moved RECORD END while building the cruise line; when the setting is completed, press to save the path. ♦ RUN CRUISE After the setting is completed, select this item to manually execute the Cruise function. ♦ EXIT Exit the CRUISE setup menu. B-3-17 IR FUNCTION (Removable IR Cut) With the IR cut filter, the speed dome can still catch clear image at night time or very dark light condition.
ALARM DETECT DETECT SWITCH OFF DETECT MODE INT. FOCUS EXIT YES ♦ DETECT SWITCH The item is used to enable or disable the ALARM DETECTION function. ♦ DETECT MODE Four alarm detect modes are provided for different application. INT. FOCUS The alarm will be triggered if the internal focus changes; and if the focus returns to the original position, the alarm will stop. FIX FOCUS If focus movement is detected, the alarm will be triggered, and the alarm stops when focus returns to the original position.
dome camera will memorize the center of the selected view as an original point, so it will be locked as users enter the Privacy Setup menu. Refer to the description for setting Privacy masks. NOTE: The Image Flip function will be disabled automatically while the Privacy function is enabled. ¾ 18x MODEL PRIVACY MASK MENU PRIVACY SWITCH ON TRANSPARENCY OFF COLOR BLACK SET MASK 01 EXIT YES ♦ PRIVACY SWITCH User can enable or disable the Privacy Mask function through this item.
MASK01 MENU H CENTER V CENTER H SIZE V SIZE EXIT+SAVE L/R U/D 000 000 YES H CENTER The original horizontal center of mask zone is the center of screen; it is able to move to other position by adjusting the horizontal value. V CENTER The original vertical center of mask zone is the center of screen; it is able to move to other position by adjusting the vertical value. H SIZE (00 ~ 80) User can adjust the horizontal size of privacy mask through this item.
♦ YEAR / MONTH / DAY The items are for setting up the system date. ♦ HOUR / MINUTE This items are for setting up the system time. ♦ EXIT+SAVE Exit this page. B-3-21 EXIT OSD To exit the OSD setup menu, users can select this item.
