E11 1MP Cube with Basic WDR, Fixed lens Hardware User’s Manual (PoE) Ver.
E11 Hardware User’s Manual Table of Contents 0. Precautions 3 1. Introduction 4 Package Contents ........................................................................... 4 Features and Benefits ..................................................................... 5 Safety Instructions .......................................................................... 6 Physical description ........................................................................ 8 Basic Connections .........................
E11 Hardware User’s Manual 0. Precautions Read these instructions You should read all the safety and operating instructions before using this product. Heed all warnings You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instruction given may directly endanger people, cause damage to the system or to other equipment.
E11 Hardware User’s Manual 1. Introduction Package Contents E11 Camera Stand Accessories Warranty Card QIG 4 www.acti.
E11 Hardware User’s Manual Features and Benefits This is a cutting-edge digital video surveillance camera. It can compress and transmit real time images with outstanding image quality through a standard TCP/IP network. This camera is your best choice to build an intelligent IP surveillance system. H.264 High Profile/MJPEG Multi-Codec Dual Streaming This device supports 2 compression formats, H.264 High Profile and MJPEG.
E11 Hardware User’s Manual Safety Instructions Don’t open the housing of the product Cleaning Disconnect this video product from the power supply before cleaning. Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards. Water and Moisture Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool and the like.
E11 Hardware User’s Manual Safety Check Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine if the video product is in proper operating condition. 7 www.acti.
E11 Hardware User’s Manual Physical description 1) Built-in Microphone 2) Audio Output The IP device supports audio output with earphone jack 3) Reset Button Step 1: Press and continue to hold the Reset Button for 15 seconds (with a sharp tipped object, like a pen.) after the unit has successfully completed the boot process. Step 2: The Ethernet LED light will turn off for about 1~2 seconds and flash on for another second. By this time the reset to default operation is already completed.
E11 Hardware User’s Manual Basic Connections Follow the procedures below to connect the IP device to the respective apparatuses. Please use a PoE (Power over Ethernet) supported switch or injector: 1) Connect your IP Camera to the PoE Switch / Injector by CAT5 or CAT6 cables with RJ45 connector. 2) Connect your PoE Switch / Injector to PC with another CAT5 / CAT6 network cable. 9 www.acti.
E11 Hardware User’s Manual Product Specification E11 • Device Device Type Image Sensor Day / Night Minimum Illumination Mechanical IR Cut Filter IR Sensitivity Range Electronic Shutter Cube Camera Progressive Scan CMOS No Color: 0.1 lux at F1.8 (30 IRE, 2400 °K) No No 1/5 - 1/2,000 sec (Manual / Auto mode) • Lens Focal Length / Aperture Iris Focus Mount Type Horizontal Viewing Angle Fixed focal, f4.2 mm / F1.8 Fixed iris Manual focus CS Mount (interchangeable lens) 57.
E11 Hardware User’s Manual 2. Accessing Camera If you have DHCP server / router in your network: Many network server / routers are able to automatically provide IP addresses through DHCP. If you are using such a network, just plug in your computer and IP Camera into the network and your IP device will acquire network address by itself. Find and access the device with our IP Utility program. You may download it at: http://www.acti.
E11 Hardware User’s Manual Please set the settings as below. IP address: 192.168. 0.xxx Subnet mask: 255.255.255. 0 (NOTE: xxx should be a number from 1 to 254 except 100, which is used by the IP device. Please also make sure that no two equipments use the same IP address in the same network..) 4. Open Internet Explorer (Version 6.0 or above) , and type in the Default IP: 192.168.0.100 5.
E11 Hardware User’s Manual 6. After logging in, you will see the video from camera. To go to the main menu, click the “Setup” button on the top left. If you are using a single camera, this is enough to access the device. If you are using multiple devices, you need to change the current device to another unused IP address, so that when the next device is connected to the network, no two devices use the same IP. Please perform the following steps. 7. Go to IP Settings -> Connection Type 8.
E11 Hardware User’s Manual 10. Click “Apply” 11. Please go to System -> Save & Reboot, and click “Apply”. Internet Explorer will close after a few seconds. This is normal. 12. Wait for 30 seconds, and open IE again to connect to the new IP. (In this example, 192.168.0.101). For the second device or more you add into the network, please type the correct IP. 13. Adjust the default Video setting by going to Video -> Video Please refer the firmware manual for the detail information. 14 www.acti.
