E51 1MP Indoor Dome with Basic WDR, Fixed lens Hardware User’s Manual (PoE) Ver.
E51 Hardware User’s Manual Table of Contents 0. Precautions 3 1. Introduction 4 Package Contents ........................................................................... 4 Features and Benefits ..................................................................... 5 Safety Instructions .......................................................................... 6 Physical description ........................................................................ 8 Installation Procedure ....................
E51 Hardware User’s Manual 0. Precautions Read these instructions You should read all the safety and operating instructions before using this product. Heed all warnings You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instruction given may directly endanger people, cause damage to the system or to other equipment.
E51 Hardware User’s Manual 1. Introduction Package Contents E51 Accessories Warranty Card QIG Drill Template 4 www.acti.
E51 Hardware User’s Manual Features and Benefits This is a cutting-edge digital video surveillance camera. It can compress and transmit real time images with outstanding image quality through a standard TCP/IP network. This camera is your best choice to build an intelligent IP surveillance system. H.264 High Profile/MJPEG Multi-Codec Dual Streaming This device supports 2 compression formats, H.264 High Profile and MJPEG.
E51 Hardware User’s Manual Safety Instructions Don’t open the housing of the product Cleaning Disconnect this video product from the power supply before cleaning. Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards. Water and Moisture Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool and the like.
E51 Hardware User’s Manual Safety Check Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine if the video product is in proper operating condition. 7 www.acti.
E51 Hardware User’s Manual Physical description 1) Power LED LED light will light up while the power is on. LED light will light off after the unit has successfully completed the boot process. 2) Ethernet Port The IP device connects to the Ethernet via a standard RJ45 connector. Supporting NWAY, this IP device can auto detect the speed of local network segment (10Base-T/100Base-TX Ethernet).
E51 Hardware User’s Manual Installation Procedure Ceiling Mount Use the drill template, and drill a hole with φ35 on the ceiling Use the mounting plate and choose the correct three screw holes. Tighten the plate to ceiling with T4*20 screws (not to use screws other than flat heads) 9 www.acti.
E51 Hardware User’s Manual Please make sure the screw is flat on the plate, protruding is incorrect. Connect cables through the hole on the ceiling and plate, or on the side of casing Fasten the camera to ceiling by turning clockwise direction 10 www.acti.
E51 Hardware User’s Manual Insert the cables (Network) through the mounting plate and connect to the camera. Then use the little strap in bundled accessory to fasten the network cable. Done 11 www.acti.
E51 Hardware User’s Manual Wall Mount Tighten wall mount bracket to the wall by 3 PAN Head Tapping screws Use the mounting plate and choose the correct three screw holes. Tighten the plate to wall mount bracket with M4*6 screws (not to use screws other than flat heads), and connect all necessary cables through the hole on the plate and wall mount kit 12 www.acti.
E51 Hardware User’s Manual Please make sure the screw is flat on the plate, protruding is incorrect. Insert the cables (power/Network/audio) through the mounting plate and connect to the camera. Then use the little strap in bundled accessory to fasten the network cable. 13 www.acti.
E51 Hardware User’s Manual Fasten the camera to wall mount kit by turning clockwise direction and done 14 www.acti.
E51 Hardware User’s Manual Adjust Viewing Angle and Focus Remove the front cover with counterclockwise direction. Based on the live view from the camera, adjust the viewing angle with pan and tilt direction. 15 www.acti.
E51 Hardware User’s Manual Adjust the focus of lens. Attach the dome cover to the camera and push it into the groove until it clicks. 16 www.acti.
E51 Hardware User’s Manual Basic Connections Follow the procedures below to connect the IP device to the respective apparatuses. Please use a PoE (Power over Ethernet) supported switch or injector: 1) Connect your IP Camera to the PoE Switch / Injector by CAT5 or CAT6 cables with RJ45 connector. 2) Connect your PoE Switch / Injector to PC with another CAT5 / CAT6 network cable. 17 www.acti.
E51 Hardware User’s Manual Product Specification E51 • Device Device Type Image Sensor Day / Night Minimum Illumination Mechanical IR Cut Filter IR Sensitivity Range IR LED Electronic Shutter Fixed Indoor Dome Camera Progressive Scan CMOS No Color: 0.1 lux at F2.0 (30 IRE, 2400 °K) No No No 1/5 - 1/2,000 sec (Manual / Auto mode) • Lens Focal Length / Aperture Iris Focus Mount Type Horizontal Viewing Angle Viewing Angle Adjustment • Video Compression Maximum Frame Rate vs.
E51 Hardware User’s Manual 2. Accessing Camera If you have DHCP server / router in your network: Many network server / routers are able to automatically provide IP addresses through DHCP. If you are using such a network, just plug in your computer and IP Camera into the network and your IP device will acquire network address by itself. Find and access the device with our IP Utility program. You may download it at: http://www.acti.
E51 Hardware User’s Manual Please set the settings as below. IP address: 192.168. 0.xxx Subnet mask: 255.255.255. 0 (NOTE: xxx should be a number from 1 to 254 except 100, which is used by the IP device. Please also make sure that no two equipments use the same IP address in the same network..) 4. Open Internet Explorer (Version 6.0 or above) , and type in the Default IP: 192.168.0.100 5.
E51 Hardware User’s Manual 6. After logging in, you will see the video from camera. To go to the main menu, click the “Setup” button on the top left. If you are using a single camera, this is enough to access the device. If you are using multiple devices, you need to change the current device to another unused IP address, so that when the next device is connected to the network, no two devices use the same IP. Please perform the following steps. 7. Go to IP Settings -> Connection Type 8.
E51 Hardware User’s Manual 10. Click “Apply” 11. Please go to System -> Save & Reboot, and click “Apply”. Internet Explorer will close after a few seconds. This is normal. 12. Wait for 30 seconds, and open IE again to connect to the new IP. (In this example, 192.168.0.101). For the second device or more you add into the network, please type the correct IP. 13. Adjust the default Video setting by going to Video -> Video Please refer the firmware manual for the detail information. 22 www.acti.
