Encoder Firmware V4.06.09 User’s Manual 4” Indoor Dome Series Hardware Manual D61, D62, D64, D65, E61, E62, E63, E64, E65, E66, E67, E68, E69 2013/03/05 1 www.acti.
Hardware Manual Table of Contents Precautions ............................................................. 3 Introduction ............................................................ 4 The List of Models ................................................................................... 4 Package Contents .................................................................................... 5 Safety Instructions ...................................................................................
Hardware Manual Precautions Read these instructions You should read all the safety and operating instructions before using this product. Heed all warnings You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instruction given may directly endanger people, cause damage to the system or to other equipment.
Hardware Manual Introduction The List of Models This hardware manual contains the following models: D61 D62 D64 D65 E61 E62 E63 E64 E65 E66 E67 E68 E69 1MP Indoor Dome with SLLS, Vari-focal lens, f2.8-12mm/F1.4, H.264, 720p/30fps, DNR, MicroSDHC, PoE 2MP Indoor Dome with SLLS, Vari-focal lens, f2.8-12mm/F1.4, H.264, 1080p/30fps, DNR, MicroSDHC, PoE 1MP Indoor Dome with D/N, IR, Vari-focal lens, f2.8-12mm/F1.4, H.
Hardware Manual Package Contents 1. Camera OR D61, D62, E66, E67, E68 D64, D65, E61, E62, E63, E64, E65, E69 2. Screw Pack 3. Drill Template These screws are for surface mounting. If you need to use specific mounting accessories, the screws are included in the package of mounting accessories. 4. Quick Installation Guide 5. Warranty Policy 5 www.acti.
Hardware Manual Safety Instructions Cleaning Disconnect this video product from the power supply before cleaning. Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards. Water and Moisture Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool and the like.
Hardware Manual Physical Description OR D61, D62, E66, E67, E68 D64, D65, E61, E62, E63, E64, E65, E69 1) Reset Button The purpose of reset button is to restore the factory default settings of the camera, including administrator’s password. The reset button can be used for following purposes: 1. The administrator’s password has been forgotten and therefore the camera cannot be accessed. 2.
Hardware Manual Installation and Access Camera Installation This camera can be surface mounted without needing any additional accessories. Use the screws from the screw pack and mount the camera to the surface using following screw holes. If you need to drill the holes to the surface first, such as concrete wall or ceiling, please use the drill template, provided in the camera package.
Hardware Manual Accessing Camera Connect the Equipment To be able to connect to the camera firmware from your PC, both the camera and the PC have to be connected to each other via Ethernet cable. At the same time, the camera has to have its own power supply. In case of PoE cameras, you can use a PoE Injector or a PoE Switch between the camera and the PC. The cameras that have the DC power connectors may be powered on by using a power adaptor.
Hardware Manual In the example below, we successfully found D11 camera that we had just connected to the network. With the left mouse click on D11 it is possible to automatically launch the default browser of the PC with the IP address of the target camera filled in the address bar of the browser already. If you work with our cameras regularly, then there is even a better way to discover the cameras in the network – by using IP Utility.
Hardware Manual Use the default IP address of a camera: If there is no DHCP server in the given network, the user may have to assign the IP addresses to both PC and camera manually to make sure they are in the same network segment. When the camera is plugged into network and it does not detect any DHCP services, it will automatically assign itself a default IP: 192.168.0.100 Whereas the default port number would be 80.
Hardware Manual Manually adjust the IP addresses of multiple cameras: If there are more than 1 camera to be used in the same local area network and there is no DHCP server to assign unique IP addresses to each of them, all of the cameras would then have the initial IP address of 192.168.0.100, which is not a proper situation for network devices – all the IP addresses have to be different from each other.
Hardware Manual Access the Camera Now that the camera and the PC are both having their unique IP addresses and are under the same network segment, it is possible to use the Web browser of the PC to access the camera. You can use any of the browsers to access the camera, however, the full functionality is provided only for Microsoft Internet Explorer.
Hardware Manual Assuming that the camera’s IP address is 192.168.0.100, you can access it by opening the Web browser and typing the following address into Web browser’s address bar: http://192.168.0.100 Upon successful connection to the camera, the user interface called Web Configurator would appear together with the login page. The HTTP port number was not added behind the IP address since the default HTTP port of the camera is 80, which can be omitted from the address for convenience.
