Indoor Mini Dome & Indoor Mini Fisheye Dome Hardware Manual D91, D92, E91, E92, E93, E94, E95, E96, E97 Ver.
Hardware Manual Table of Contents Precautions 4 Safety Instructions ........................................................................... 6 Introduction 7 List of Models.................................................................................... 7 Package Contents............................................................................. 8 Physical Description ........................................................................
Hardware Manual Using the Default Camera IP Address.......................................... 30 Access the Camera ......................................................................... 32 3 www.acti.
Hardware Manual Precautions Read these instructions You should read all the safety and operating instructions before using this product. Heed all warnings You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instruction given may directly endanger people, cause damage to the system or to other equipment.
Hardware Manual Federal Communications Commission Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Hardware Manual Safety Instructions Cleaning Disconnect this video product from the power supply before cleaning. Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards. Water and Moisture Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool and the like.
Hardware Manual Introduction List of Models This hardware manual contains the following models: D91 1MP Indoor Mini Dome with Fixed lens D92 3MP Indoor Mini Dome with Fixed lens E91 E92 1MP Indoor Mini Dome with Basic WDR, Fixed lens 3MP Indoor Mini Dome with Basic WDR, Fixed lens E93 5MP Indoor Mini Dome with Basic WDR, Fixed lens E94 1.
Hardware Manual Package Contents Camera Camera E96 (Mini Fisheye Dome) or Drill Template Screw Kit Drill Template Lens Focus Tuner Hexagon Screwdriver (Not available in E93, E96, and E97 models) Quick Installation Guide Warranty Card 8 www.acti.
Hardware Manual Physical Description Mini Dome Mini Fisheye Dome 9 www.acti.
Hardware Manual 1) Ethernet Port The Ethernet port connects to a network using an Ethernet cable. 2) Reset Button The Reset Button is used to restore the factory default settings of the camera, including the administrator’s password. How to reset the camera? While the power is on, press and hold the Reset Button for 5 seconds or until the Blue LED lights up.
Hardware Manual Installation Procedures Before mounting the camera, remove the dome cover by loosening the three (3) screws. There are two ways to mount the camera: Surface mount: Use this method to mount the camera directly on the ceiling. See Installing the Camera on a Surface on page 12. Gang Box Mount: If the camera will be mounted on a gang box (applicable in some areas in the US), a gang box converter (not included in the camera package) is needed.
Hardware Manual Installing the Camera on a Surface 1. Mark the location of the screw holes base on the drill template included in the package. Conduit Hole NOTE: Depending on the surface where you will install the camera, it may be necessary to drill three (3) holes with φ 3.5 on the ceiling and use the supplied screw tox. 2. Route the cables through the ceiling, taking the Conduit Hole on the drilling template as a reference.
Hardware Manual 3. Use the camera body and locate the three (3) screw holes. 4. Install the camera body to the ceiling using the three (3) screws included in the camera package. NOTE: Please make sure the screw is flat on the plate. 13 www.acti.
Hardware Manual 5. Connect the Ethernet cable to the Ethernet port of the camera. 6. Adjust the camera viewing angle and focus. See How to Adjust the Viewing Angle and Focus on page 21. NOTE: Not applicable to E96 model. 7. Attach the cover to the camera body and tighten the three (3) screws to secure it. 14 www.acti.
Hardware Manual Installing the Camera on a Gang Box In case the camera has to be installed on a gang box, use the gang box converter below to install your camera. Gang Box Converter PMAX-0805 Description Supported Gang Box The gang box converter is installed onto the gang 4” Round box which can either be on a surface or inside the 4” Octagon surface. The camera can then be installed onto the gang box converter. NOTE: The gang box and the gang box converter are not included in the camera package.
Hardware Manual Step 1: Install the Gang Box Before installation, note that the gang box must be installed with either of the following orientation: Screw Holes from Left to Right Screw Holes from Right to Left 4” Round 4” Octagon 1. Remove a knockout on the gang box to route the network cable. 2. Route the network cable along the surface or inside the surface and into the gang box. 3. Attach the gang box on the surface or inside the surface according to the recommended orientation above. 16 www.acti.
Hardware Manual Step 2: Install the Gang Box Converter 1. Route the network cable to pass through the hole of the gang box converter. 2. Install the gang box converter onto the gang box using the screws included in the gang box package. Note which screw holes to attach to secure the converter to the gang box. Screw Holes from Left to Right Screw Holes from Right to Left NOTE: Same screw holes apply when using the 4” octagon gang boxes. 17 www.acti.
Hardware Manual Step 3: Connect the Cable Connect the network cable to the Ethernet port of the camera. Step 4: Install the Camera 1. Align the camera screw holes to the screw holes of the gang box converter. 2. Attach the three (3) screws (included in the gang box converter package) to secure the camera to the converter. 18 www.acti.
Hardware Manual Step 5: Connect to Network On the network side, connect the other end of the network cable to a network switch. See Basic Connections on page 20 for more information. Step 6: Access the Camera Live View See Accessing the Camera on page 28 for more information on how to access the Live View of the camera. Step 7: Adjust the Viewing Angle and Focus Based on the Live View, adjust the viewing angle, focus, and orientation of the camera.
Hardware Manual Basic Connections Follow the procedures below to connect the camera to the network. Please use a PoE (Power over Ethernet) supported switch or injector: 1) Connect your IP Camera to the PoE Switch / Injector using an Ethernet cable. 2) Connect your PoE Switch / Injector to a PC / network using another Ethernet cable. 20 www.acti.
Hardware Manual Other Adjustments and Accessories How to Adjust the Viewing Angle and Focus NOTE: The following procedures are not applicable to E96 (Mini Fisheye Dome) cameras. 1. Loosen the three (3) screws to remove the dome cover. 2. Based on the live view from the camera, adjust the viewing angle with pan and tilt direction (for Mini Dome models only). 21 www.acti.
Hardware Manual 3. Adjust the focus. NOTE: Not applicable for E93 / E97 model because the camera is already pre-focused. a. Attach the focus tuner (included in the camera package) on the lens and adjust the focus of the lens. b. Remove the lens focus tuner. 4. Attach the dome cover to the camera and tighten the three (3) screws. 22 www.acti.
Hardware Manual How to Replace the Dome Cover For more discrete surveillance needs, the pre-installed dome cover can be replaced with a smoked, non-vandal proof dome cover. The smoked dome cover is an optional accessory; contact your sales agent to purchase. Optional Accessories PDCX-1106 To replace the dome cover, follow the procedures below: 1. Loosen the three (3) screws to remove the dome cover. 2. Push the clips outwards to release the dome cover latches. 23 www.acti.
Hardware Manual 3. Remove the ring from the cover. 4. Insert ring to the new dome cover and latch it to the cover body. 24 www.acti.
Hardware Manual How to Replace the Lens (for D91, D92, E91, E92 only) For wider viewing angle, the bundled lens can be replaced with the optional IR-compatible lens. Contact your sales agent to purchase. Optional Lens PLEN-4103 PLEN-4104 To replace the lens, follow the procedures below: 1. Using the bundled hex screwdriver, loosen the three (3) screws to open the dome cover. 2. Attach the lens focus tuner to the lens and continuously rotate until the lens comes off. 25 www.acti.
Hardware Manual 3. When the lens comes off, remove the spring and remove the bundled lens from the lens focus tuner. 4. Remove the transparent plastic from the replacement lens. 5. Attach the spring to the replacement lens. 6. Continuously rotate the replacement lens to attach it to the camera. 26 www.acti.
Hardware Manual 7. Attach the lens focus tuner when the tip of the lens is difficult to hold then turn it clockwise or counter-clockwise to adjust the camera focus. See How to Adjust the Viewing Angle and Focus on page 21 for more information. 8. Close the dome cover. 27 www.acti.
Hardware Manual Accessing the Camera Configure the IP Addresses In order to be able to communicate with the camera from your PC, both the camera and the PC have to be within the same network segment. In most cases, it means that they both should have very similar IP addresses, where only the last number of the IP address is different from each other. There are 2 different approaches to IP Address management in Local Area Networks – by DHCP Server or Manually.
Hardware Manual By double-clicking with the left mouse on the camera model, it is possible to automatically launch the default browser of the PC with the IP address of the target camera filled in the address bar of the browser already. If you work with our cameras regularly, then there is even a better way to discover the cameras in the network – by using IP Utility.
Hardware Manual Using the Default Camera IP Address If there is no DHCP server in the given network, the user may have to assign the IP addresses to both PC and camera manually to make sure they are in the same network segment. When the camera is plugged into network and it does not detect any DHCP services, it will automatically assign itself a default IP: 192.168.0.100 Whereas the default port number would be 80.
Hardware Manual Manually adjust the IP addresses of multiple cameras: If there are more than 1 camera to be used in the same local area network and there is no DHCP server to assign unique IP addresses to each of them, all of the cameras would then have the initial IP address of 192.168.0.100, which is not a proper situation for network devices – all the IP addresses have to be different from each other.
Hardware Manual Access the Camera Now that the camera and the PC are both having their unique IP addresses and are under the same network segment, it is possible to use the Web browser of the PC to access the camera. You can use any of the browsers to access the camera, however, the full functionality is provided only for Microsoft Internet Explorer.
Hardware Manual The following examples in this manual are based on Internet Explorer browser in order to cover all functions of the camera. Assuming that the camera’s IP address is 192.168.0.100, you can access it by opening the Web browser and typing the following address into Web browser’s address bar: http://192.168.0.100 Upon successful connection to the camera, the user interface called Web Configurator would appear together with the login page.
Hardware Manual To check the firmware version through the Web Configurator, access the Setup page and click System > System Info. 1 2 3 For further operations, please refer to the Firmware User Manual. 34 www.acti.
Copyright © 2014, ACTi Corporation, All Rights Reserved 7F, No. 1, Alley 20, Lane 407, Sec. 2, Ti-Ding Blvd., Neihu District, Taipei, Taiwan 114, R.O.C. TEL : +886-2-2656-2588 FAX : +886-2-2656-2599 Email: sales@acti.
