E92 3MP Indoor Mini Dome with Basic WDR, Fixed lens Hardware User’s Manual (PoE) Ver.
E92 Hardware User’s Manual Table of Contents 0. Precautions 3 1. Introduction 4 Package Contents ........................................................................... 4 Features and Benefits ..................................................................... 5 Safety Instructions .......................................................................... 6 Physical description ........................................................................ 7 Installation Procedure ....................
E92 Hardware User’s Manual 0. Precautions Read these instructions You should read all the safety and operating instructions before using this product. Heed all warnings You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instruction given may directly endanger people, cause damage to the system or to other equipment.
E92 Hardware User’s Manual 1. Introduction Package Contents E92 Lens Focus Tuner Quick Installation Guide Accessories Warranty Card Drill Template 4 www.acti.
E92 Hardware User’s Manual Features and Benefits This is a cutting-edge digital video surveillance camera. It can compress and transmit real time images with outstanding image quality through a standard TCP/IP network. This camera is your best choice to build an intelligent IP surveillance system. H.264 High Profile/MJPEG Multi-Codec Dual Streaming This device supports 2 compression formats, H.264 High Profile and MJPEG.
E92 Hardware User’s Manual Safety Instructions Cleaning Disconnect this video product from the power supply before cleaning. Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards. Water and Moisture Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool and the like.
E92 Hardware User’s Manual Physical description 1) Power LED LED light will light up while the power is on. LED light will light off after the unit has successfully completed the boot process. 2) Ethernet Port The IP device connects to the Ethernet via a standard RJ45 connector. Supporting NWAY, this IP device can auto detect the speed of local network segment (10Base-T/100Base-TX Ethernet).
E92 Hardware User’s Manual Installation Procedure Remove the cover of the camera by loosen the 3 screws holding it. Surface Mount Drill three holes with φ3.5 on the ceiling according to the marks provided on the template. Route cables through the ceiling, taking as a reference the Conduit Hole on the drilling template. Or you may take off the removable part from the cable exit hole at the rear of the cover by sliding it out from the cover to route the cable from the camera. 8 www.acti.
E92 Hardware User’s Manual Use the camera body and locate the correct three screw holes. Tighten the camera body to the ceiling using the 3 screws included. Please make sure the screw is flat on the plate, protruding is incorrect. Attach the cover back to the camera body and tighten the 3 screws. 9 www.acti.
E92 Hardware User’s Manual Gang Box Adapter Mount This camera can also be mounted using the Gang Box Converter accessory PMAX-0803 used for 3” and 4” indoor domes. However please note that if used in combination with this accessory, a part of the plate of PMAX-0803 will remain visible after installation as shown in the picture below. First, locate the three screw holes on the accessory that can be used to attach this camera model. Connect cables through the hole on PMAX-0803 accessory. 10 www.acti.
E92 Hardware User’s Manual Tighten the camera body to the PMAX-0803 with the 3 screws included in the camera box. Finally, put the cover back on, and tighten with the 3 screw holes on the camera body. 11 www.acti.
E92 Hardware User’s Manual Adjust Viewing Angle and Focus Remove each screw to take away the front cover of the camera. Based on the live view from the camera, adjust the viewing angle with pan and tilt direction. 12 www.acti.
E92 Hardware User’s Manual Attach the focus tuner on lens to adjust the focus of lens. Remove the lens focus tuner. Attach the dome cover to the camera and tighten using the 3 screws. 13 www.acti.
E92 Hardware User’s Manual Basic Connections Follow the procedures below to connect the IP device to the respective apparatuses. Please use a PoE (Power over Ethernet) supported switch or injector: 1) Connect your IP Camera to the PoE Switch / Injector by CAT5 or CAT6 cables with RJ45 connector. 2) Connect your PoE Switch / Injector to PC with another CAT5 / CAT6 network cable. 14 www.acti.
E92 Hardware User’s Manual 2. Accessing Camera If you have DHCP server / router in your network: Many network server / routers are able to automatically provide IP addresses through DHCP. If you are using such a network, just plug in your computer and IP Camera into the network and your IP device will acquire network address by itself. Find and access the device with our IP Utility program. You may download it at: http://www.acti.
E92 Hardware User’s Manual Please set the settings as below. IP address: 192.168. 0.xxx Subnet mask: 255.255.255.0 (NOTE: xxx should be a number from 1 to 254 except 100, which is used by the IP device. Please also make sure that no two equipments use the same IP address in the same network..) 4. Open Internet Explorer (Version 6.0 or above) , and type in the Default IP: 192.168.0.100 5.
E92 Hardware User’s Manual 6. After logging in, you will see the video from camera. To go to the main menu, click the “Setup” button on the top left. If you are using a single camera, this is enough to access the device. If you are using multiple devices, you need to change the current device to another unused IP address, so that when the next device is connected to the network, no two devices use the same IP. Please perform the following steps. 7. Go to IP Settings -> Connection Type 8.
E92 Hardware User’s Manual 10. Click “Apply” 11. Please go to System -> Save & Reboot, and click “Apply”. Internet Explorer will close after a few seconds. This is normal. 12. Wait for 30 seconds, and open IE again to connect to the new IP. (In this example, 192.168.0.101). For the second device or more you add into the network, please type the correct IP. 13. Adjust the default Video setting by going to Video -> Video Please refer the firmware manual for the detail information. 18 www.acti.
