Quick Installation Guide ENR-220P 4-Channel 2-Bay Desktop Standalone NVR with 4-port PoE connectors ENR-221 9-Channel 2-Bay Desktop Standalone NVR ENR-221P 9-Channel 2-Bay Desktop Standalone NVR with 8-port PoE connectors ENR-222 16-Channel 2-Bay Desktop Standalone NVR
BEFORE YOU START Thank you for purchasing ACTi ENR Standalone Network Video Recorder. This guide contains all the information you need to quickly set up the device via local display interface. For detailed instructions on installation and operation, please search for the product manuals on http://www.acti.com/downloadcenter. The items below are required for installation: • Network cameras • Monitor (with HDMI input and the cable) • Network cables • Network switch • At least one ACTI-certified 3.
2 AT A GLANCE FRONT PANEL 1 HDMI Output 2 USB 2.0 Ports x 2 3 LED Indicators - Power LED (blue) - System LED (orange) - Hard Disk LED (green) 4 Reset Button 5 Power Button 1 2 3 4 5 REAR PANEL ENR-221 & ENR-222 1 2 Power Connector USB 3.
2 AT A GLANCE REAR PANEL ENR-220P 1 Digital Input / Output 2 Audio Input / Output 3 Power Connector 4 2 USB 3.0 Port 5 WAN Port 6 LAN Port 7 1 Power Over Ethernet (PoE) (PoE) x 4 ports 3 2 4 5 6 4 5 6 7 AT A GLANCE REAR PANEL ENR-221P 1 Digital Input / Output 2 Audio Input / Output 3 Power Connector 4 1 2 USB 3.
3 INSTALL HARD DISK DRIVE Step 1 Remove the front panel screws, and then remove the back panel screws. Step 2 Slide the case backwards until it stops, and then lift it up to remove. Step 3 Insert Disk 2 in the lower bay, connect a SATA Power Cable and SATA Data Cable 2 to the hard disk. Step 4 Make sure you connect the correct data cable to the corresponding disk. Step 5 Lock Disk 2 using one disk screw on each side of the hard disk bay.
4 CONNECTIONS The example below displays a network with ENR and basic required peripherals to start using the device. ENR-221 and ENR-222 Network Cameras ENR automatically assigns IP addresses to cameras via LAN. 192.168.0.101 192.168.0.102 192.168.0.103 192.168.0.104 PoE Switch Default IP Address LAN : 192.168.0.10 WAN: DHCP assigned HDMI Monitor USB Devices Power Source (Optional) Connect to another network via WAN for remote client connection. Default IP Address LAN : 192.168.0.
5 LOGIN 1. On the front panel, press the POWER BUTTON to turn on the ENR. 2. On the Login screen, using the on-screen keyboard, type the Account and Password. Account: admin Password: 123456 “123456” is the default password of the administrator’s user account. For security reasons, please remember to change it.
6 1. 2. 3. 4. 7 FORMAT THE HDD Click the System Setup icon on the Live View screen. Click the Storage > Management page. Select the hard disk to format, then click Format. Repeat the above steps to format the other disk, and then click OK. ADD DEVICES 1. On the Live View screen, click Add. 2. Click Add Camera from the pop-up menu. Or, click other network devices to add them in the ENR. You may also group devices by creating a group.
Add Camera Manually If you are adding cameras located in another network, click Add Camera Manually. Fill in the IP address, HTTP Port, Account and Password. Then click Add. Or, use the RTSP page for RTP protocol. 8 CHECK LIVE VIEW After adding the cameras, the models are listed on the left panel of the Live View screen. 1. Create a tab view on the right panel, click 2. Drag a model to the Live View screen. . Double-click the page tab to rename it. Right-click on a channel to access the pop-up menu.
9 MANAGE DEVICES Managing the devices can be done from the Live View screen. Right-click on the device model from the left panel, then click to: • Rename the device name on the list • Delete the device from the list • Setup the camera settings (see below) Camera Settings From the Camera Settings screen, click the corresponding page tab to configure video settings, set up motion detection, event and schedule recordings. To modify the camera settings, click Get Camera Settings.
10 CHECK RECORDINGS On the Live View screen, click the Playback to enter the Playback screen. icon on the bottom right corner On the time bar, drag the current-time indicator to your desired position, and then click the Playback icon.
10 SYSTEM SETUP Administrators can configure the ENR system setup. 1. On the Live View screen, click the Setup icon on the bottom left corner. 2. On the Setup screen, click a menu page tab to access the settings: • • • • • • • System: Includes system information, date and time, email settings, etc. Network: Includes network related configurations. Storage: Manages the storage settings of the ENR. Maintenance: Includes firmware upgrade and station management system.
