KCM-3211 3.6x Zoom H.264 4-Megapixel IP D/N PoE Indoor Dome with P-Iris (DC 12V / PoE) Ver.
KCM-3211 Hardware Manual Table of Contents Precautions 3 Introduction 4 Package Contents............................................................................. 4 Features and Benefits ...................................................................... 5 Safety Instructions ........................................................................... 6 Physical description .........................................................................
KCM-3211 Hardware Manual Precautions Read these instructions You should read all the safety and operating instructions before using this product. Heed all warnings You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instruction given may directly endanger people, cause damage to the system or to other equipment.
KCM-3211 Hardware Manual Introduction Package Contents KCM-3211 QIG Product CD Terminal Blocks for Power DI/O and Audio Accessories Warranty Card Drill Template 4 www.acti.
KCM-3211 Hardware Manual Features and Benefits This is a cutting edge network video surveillance camera. It can capture, compress and transmit real time video in excellent quality (8 FPS 4Megapixel, 2032 x 1920). This camera is your best choice to build an intelligent IP surveillance system. Adaptive Profile With the innovative embedded Image Signal Processor (ISP), this camera responds to changing lighting condition with customized algorithm. This allows for clear image with very little noise at night.
KCM-3211 Hardware Manual developers. Software developers can save considerable efforts by using our Streaming Library or ActiveX control. Safety Instructions Don’t use the power supply with other voltages This device is likely to be damaged or damage other equipments / personnel, if you use a power supply with different voltage than the one included with this device. All warranty of this product will be voided in the situations above.
KCM-3211 Hardware Manual 4) If the video product does not operate normally by following the operating Instructions in this manual. Adjust only those controls that are covered by the instruction manual, as an improper adjustment of other controls may result in damage, and will often require extensive work by a qualified technician to restore the video product to its normal operation.
KCM-3211 Hardware Manual Physical description Reset Button DC 12v Power Input Power Button Micro SD / Micro SDHC Card Slot Ethernet Port Audio Input / Output Digital Input / Output 1) Reset Button Step 1: Switch off IP device by disconnecting the power cable Step 2: Press and continue to hold the Reset Button (with a sharp tipped object, like a pen.) Step 3: Reconnect the power cable while continuing to hold the reset button.
KCM-3211 Hardware Manual Restore to Default Complete Power On On (3s) On 1s Off (about 15s) Off (10~15s) Stay On About 20 Seconds 2) Power Button Press the Power Button and then camera will reboot automatically. 3) Ethernet Port The IP device connects to the Ethernet via a standard RJ45 connector. Supporting NWAY, this IP device can auto detect the speed of local network segment (10Base-T/100Base-TX Ethernet).
KCM-3211 Hardware Manual 1. Attach the cables for the device securely to the supplied green connector block. 2. Once cables are connected, push connector block into the terminal connector on camera. 5) DC 12V Power Input Connect DC power source to the terminal block. The wire with white dashed lines is the live wire, which should connect to the 12V pin.
KCM-3211 Hardware Manual Installation Procedure Surface Installation You may directly drill holes on the wall or the ceiling and directly install the camera on a surface. To do this, follow the procedures below: 1) Drill the holes Using the supplied drill template in the camera package, mark the holes on the wall / ceiling and drill the holes. 2) Remove the cover Remove the dome cover by unscrewing the three attachments 11 www.acti.
KCM-3211 Hardware Manual 3) Screw the camera to the wall/ceiling CAUTION: When using electric screwdrivers, be careful not to touch the internal camera components while attaching the screws. Since electric screwdrivers vary in sizes, speed, and force, they may bruise and damage the internal camera components. DISCLAIMER: ACTi will not be responsible for camera damage caused by improper installations or the misuse of equipment for installation.
KCM-3211 Hardware Manual Adjusting the Viewing Angle Camera Parts Overview Adjustment Procedures 3 2 1 1. Loosen the tilt adjustment screws, adjust the tilt, and then tighten back the screws to fix the tilt position. 2. Move the rotation adjustment to rotate the viewing orientation. 3. Move the pan direction left or right. 13 www.acti.
KCM-3211 Hardware Manual NOTE: If you need to tighten or loosen the pan adjustment knob and adjustment by hand is not enough, insert the bundled pan bracket wrench into the hole on the knob and then push it to the left or to the right. 14 www.acti.
KCM-3211 Hardware Manual Accessing Camera If you have DHCP server / router in your network: Many network server / routers are able to automatically provide IP addresses through DHCP. If you are using such a network, just plug in your computer and IP Box Cam into the network and your IP device will acquire network address by itself. Find and access the device with our IP Utility program. You may download it at: http://www.acti.
KCM-3211 Hardware Manual 4. Open Internet Explorer (Version 6.0 or above) , and type in the Default IP: 192.168.0.100 5. When you see the login window, please input default user and password: Default User: Admin Password: 123456 6. After logging in, you will see the video from camera. To go to the main menu, click the ”Setup” button on the top left. If you are using a single camera, this is enough to access the device. 16 www.acti.
KCM-3211 Hardware Manual If you are using multiple devices, you need to change the current device to another unused IP address, so that when the next device is connected to the network, no two devices use the same IP. Please perform the following steps. 7. Go to Network -> Connection Type 8. Change the IP mode to Static. 9. Change the IP to 192.168.0.101 or any other unused IPs. Do NOT use the PC’s IP address or 192.168.0.100.).
