Encoder Firmware V4.06.09 User’s Manual KCM-3311 3.6x Zoom H.
Hardware Manual Table of Contents Precautions ............................................................. 3 Safety Instructions .................................................................................... 4 Introduction ............................................................. 5 Package Contents...................................................................................... 5 Physical Description .................................................................................
Hardware Manual Precautions Read these instructions You should read all the safety and operating instructions before using this product. Heed all warnings You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instructions given may directly endanger people, cause damage to the system or to other equipment.
Hardware Manual Safety Instructions Cleaning Disconnect this video product from the power supply before cleaning. Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards. Do not use accessories not recommended by the manufacturer Only install this device in a dry place protected from weather. Servicing Do not attempt to service this video product yourself. Refer all servicing to qualified service personnel.
Hardware Manual Introduction Package Contents KCM-3311 QIG Accessories Warranty Card Drill Template 5 www.acti.
Hardware Manual Physical Description 1) Reset Button Step 1: Switch off IP device by disconnecting the power cable Step 2: Press and continue to hold the Reset Button (with a sharp tipped object, like a pen.) Step 3: Reconnect the power cable while continuing to hold the reset button. The red Power LED light will flash on for 3 second first, turn off for about 15 seconds, flash on for another second and turn off again. By this time the reset to default operation is already completed.
Hardware Manual 2) Power Button Press the Power Button and then camera will reboot automatically. 3) Ethernet Port The IP device connects to the Ethernet via a standard RJ45 connector. Supporting NWAY, this IP device can auto detect the speed of local network segment (10Base-T/100Base-TX Ethernet). 7 www.acti.
Hardware Manual Installation The camera can be directly installed on walls or mounted in the ceilings using mounting kits. This section describes the two basic ways that you can do to install the camera. NOTE: Due to continuous product improvements, the camera images on this documentation may slightly differ from the actual camera that you received. Installation procedures remain the same.
Hardware Manual 3) Screw the camera to the wall/ceiling CAUTION: When using electric screwdrivers, be careful not to touch the internal camera components while attaching the screws. Since electric screwdrivers vary in sizes, speed, and force, they may bruise and damage the internal camera components. DISCLAIMER: ACTi will not be responsible for camera damage caused by improper installations or the misuse of equipment for installation.
Hardware Manual Method 2: Using the Flush Mount You can use the PMAX-1008 flush mount to mount the camera on ceilings. NOTE: Due to continuous product improvements, the camera images on this documentation may slightly differ from the actual camera that you received. Installation procedures remain the same.
Hardware Manual 2) Remove the Camera Casing Remove the three (3) screws to detach the camera casing. 11 www.acti.
Hardware Manual 3) Prepare the Flush Mount 1. Unpack the flush mount. Retaining bracket 2. Peel off the lining of the three (3) foam rubber pads and attach a rubber pad to each retaining bracket. 12 www.acti.
Hardware Manual 4) Attach the Camera to the Mount 1. Align the screw holes on the camera to the screw holes on the mount. 2. Attach the three (3) screws to secure the camera to the mount. CAUTION: When using electric screwdrivers, be careful not to touch the internal camera components while attaching the screws. Since electric screwdrivers vary in sizes, speed, and force, they may bruise and damage the internal camera components.
Hardware Manual 5) Loosen the Retaining Brackets Using a screwdriver, loosen the retaining brackets according to the thickness of the ceiling. 14 www.acti.
Hardware Manual 6) Connect the Network Cable Route the network cable to pass through the gap of the mount and connect it to the Ethernet port of the camera. 7) Install the Mount 1. Insert the flush mount through the hole until the bracket edges are flat on the ceiling. 15 www.acti.
Hardware Manual 2. Position the retaining brackets to hold the mount on the ceiling. NOTE: The following illustration shows how the flush mount will look like when viewed from inside the ceiling. In case you cannot access inside the ceiling, use your fingers to position the retaining brackets through the hole. 3. Tighten the screws to secure the mount. 16 www.acti.
Hardware Manual 8) Position the Lens The camera has zoom lens and auto focus capabilities so you do not need to manually adjust the focus. Position the lens on the target view area. To accurately position the target area, view the camera’s Live View on the Web Configurator, please refer to Accessing the Camera on page 22 for more information. 9) Attach the Camera Casing 1. Align the screw holes on the camera and the camera casing. 2.
Hardware Manual 10) Attach the Flush Mount Cover 1. Align the metal latches and the latches on the flush mount cover. 2. Push to firmly secure the flush mount cover latches. The mounted camera should look like the image below: 18 www.acti.
Hardware Manual How to Reset or Reposition the Lens of the Mounted Camera In case you need to reset the camera or reposition the lens, follow the procedures below: 1. Use your fingers to pry the flush mount cover off the ceiling. 2. Insert a pointed object through the reset hole or position the lens. OR 3. Attach the flush mount cover, please refer to Attach the Flush Mount Cover on page 18 for detailed instructions. 19 www.acti.
Hardware Manual Adjusting the Viewing Angle Camera Parts Overview Adjustment Procedures 3 2 1 1. Loosen the tilt adjustment screws, adjust the tilt, and then tighten back the screws to fix the tilt position. 2. Move the rotation adjustment to rotate the viewing orientation. 3. Move the pan direction left or right. 20 www.acti.
Hardware Manual NOTE: If you need to tighten or loosen the pan adjustment knob and adjustment by hand is not enough, insert the bundled pan bracket wrench into the hole on the knob and then push it to the left or to the right. 21 www.acti.
Hardware Manual Accessing the Camera If you have DHCP server / router in your network: Many network server / routers are able to automatically provide IP addresses through DHCP. If you are using such a network, just plug in your computer and IP Dome Cam into the network and your IP device will acquire network address by itself. Find and access the device with our IP Utility program. You may download it at: http://www.acti.
Hardware Manual 4. Open Internet Explorer (Version 6.0 or above) , and type in the Default IP: 192.168.0.100 5. When you see the login window, please input default user and password: Default User: Admin Password: 123456 6. After logging in, you will see the video from camera. To go to the main menu, click the ”Setup” button on the top left. If you are using a single camera, this is enough to access the device. 23 www.acti.
Hardware Manual If you are using multiple devices, you need to change the current device to another unused IP address, so that when the next device is connected to the network, no two devices use the same IP. Please perform the following steps. 7. Go to Network -> Connection Type 8. Change the IP mode to Static. 9. Change the IP to 192.168.0.101 or any other unused IPs. Do NOT use the PC’s IP address or 192.168.0.100.).
