Installation & Configuration Guide VMGB-102 with RAS 2019/08/02
INSTALLATION & CONFIGURATION GUIDE Thank you for purchasing ACTi products. The following documentation covers the installation and configuration of your device. NOTE: The accuracy of the analytics algorithm may be affected by different environmental factors or inappropriate installation. Please follow the procedures in this guide. ACTi will not be held liable for inaccuracies resulting from the aforesaid causes.
INSTALLATION & CONFIGURATION GUIDE Examples of unsuitable scenarios: Backlight Insufficient Light Installation Height Requirements The camera should be installed in the front of the passageway where it can capture the face. The horizontal tilt angle of the camera must be less than < 25 °. 2. The camera installation must be elevated. This is to avoid the situation where a face is obscured by the person in front of him in case they go through the passageway closely one after the other.
INSTALLATION & CONFIGURATION GUIDE 4. Make sure that there is no obstruction between the camera lens and the passageway. Examples of Standard Scenarios: Examples of Unsuitable Scenarios: Tilt angle is too large Elevation Capture The scenario is too wide Incline installation, with obstruction 4 www.acti.
INSTALLATION & CONFIGURATION GUIDE The scenario is too large and the face recognition rate is low 5 www.acti.
INSTALLATION & CONFIGURATION GUIDE Configuration with RAS Part 1: Access the Camera 1. Open the utility tool on the desktop. 2. Find Camera (VMGB-102) you would like to install. Note: The MAC Address will be used in the second part of 1-2, please record it for easy operation. 3. Open IE browser. (Please be sure to use IE browser.) 4. Enter the camera IP on your browser, press “Enter” to access the Camera login page. 5. Fill in the default account password and click login to log in.
INSTALLATION & CONFIGURATION GUIDE Part 2: Settings of the Camera Please refer to the following figure for the People counting setting: 1. Click “Configuration” 2. Click “Basic Settings” 3. Set network related parameters 7 www.acti.
INSTALLATION & CONFIGURATION GUIDE Please refer to the following steps for Configuration settings 1. Click “Configuration” 2. Click “Rule” 3. Check “Rule” 4. Click the “Polygon” button. Drag the mouse to set the recognition range on the screen; right-click to end the range setting. 5. Click the “Square” button. Drag the mouse to set the detection range on the screen. The identify box should enclose the eyes down to the nose only. The distance value of this range will be auto-generated and shown on “Min.
INSTALLATION & CONFIGURATION GUIDE 1. Click “Application” 2. Click “Face Picture Library” ＋number 3. Set up the parameter of Face Picture Library a. Name: Please fill “ FaceLib” b. Threshold: Please fill “70” 4. Click “ok” 9 www.acti.
INSTALLATION & CONFIGURATION GUIDE Please refer to the following steps for parameter settings 1. Click “Configuration” 2. Click “Face Picture Comparison” 3. Click “Linkage Method” then refer to the above figure to check the settings. 4. Click“Save” 10 www.acti.
INSTALLATION & CONFIGURATION GUIDE Part 3: Set up related parameters for the webpage 1. Open the webpage (Using Google chrome browser) http://localhost/MAS_RetailPackage/Setting/mgbmanagement.aspx 2. Sign in to RAS (admin/123456) 3. Settings of adding device 3-1.Click “Overview”→ “Setting”→” MGB Server” 3-2. Click the same name as the one attached to the server. (Ex: MGB Server) 3-3. Click “Add new device” as the picture below 11 www.acti.
INSTALLATION & CONFIGURATION GUIDE 3-4 Choose “VMGB-102” for the Device Type (Please refer to the picture below) 12 www.acti.
INSTALLATION & CONFIGURATION GUIDE 3-5 Configure the device details: Camera Name: (Store name +102+location) Stream URL: Please keep it blank. Camera IP: Enter the IP of VMGB-102 Server PORT Maintain the number “8000” Account: admin Password: Aa123456 3-6 Click“ Save” 3-7 Be sure all the devices have been set properly, click “Lock”. Click “Lock”→ “Save” （If there are still other devices that need to be added (except VMGB-102), please click “Lock” after all the devices have been set without error.
INSTALLATION & CONFIGURATION GUIDE 4. Store Settings 7 Click” Setting”→” Store” 1. Press “Add Store” 2. Click “Enabled” 3. Name: Store name 4. Address: Enter the address and set the location (click 5. Bussiness Hour: hours sign) Confirm with the customer and set the store opening 6. Enter the Customer Account Number. 7. Select “Recognition Device” same as the device mentioned above. 8. Press “Save” 9.
INSTALLATION & CONFIGURATION GUIDE 5. Permission 1. Click “Setting” 2. Click “UserManagement” 3. Click “Add a User” 4. Account Name：Fill in the login account 5. Email：Fill in the Email 6. Password：Fill in the Password 7. Role：Select “Manager” 8. Store：Click the store you set on step 4. 9. Click “Save” for the settings 15 www.acti.
Copyright © 2019, ACTi Corporation All Rights Reserved 7F, No. 1, Alley 20, Lane 407, Sec. 2, Ti-Ding Blvd., Neihu District, Taipei, Taiwan 114, R.O.C. TEL : +886-2-2656-2588 FAX : +886-2-2656-2599 Email: sales@acti.
