ODM90903 ODM91003 9”, 10.
CAUTION RISK OF ELECTRONIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Important Notice An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation.
FEATURES ODM90903 / ODM91003 • 9”, 10.2” TFT (Thin Film Transistor) Active Matrix LCD (Liquid Crystal Display) Monitor • Built-in DVD Player • OSD (On Screen Display) for control of picture quality and functions • Three Audio / Video Source inputs (DVD/USB/CARD, AV and AUX).
CONTROLS AND INDICATORS DIAGRAM (FRONT VIEW) 1 6 6 2 3 4 5 7 8 8 9 10 1. POWER ( ) Control Used to turn the system on/off (standby). 2. PLAY (u) Control This control is used to start playback of a disc. 3. Source Select (S) Use to select one of the two sources: DVD/USB/CARD, AV and AUX. 4. STOP (n) Control - Press STOP once : Stops playback, Pressing the PLAY button again will resume normal playback from where movie was stopped.
6. Dome Lights Provide additional interior illumination. 7. Screen Release Press to release the screen. 8. Ventilation holes 9. LCD Cut Off Switch Used to turn off the LCD backlight when the LCD is in the closed position. 10. LCD Panel CONTROL FUNCTION DESCRIPTION (SIDE VIEW) 1 2 3 4 5 6 1. Disc insertion Slot For loading and removing discs. Unit must be in power on state to load a disc. Insert disc with label side facing upwards. 2.
CONTROL FUNCTION DESCRIPTION (BACK VIEW) 1 1. REAR IR SENSOR REMOTE CONTROL OPERATION Initial Use When purchased the remote control has a battery installed with a Pull Tab to prevent battery discharge. Remove the Pull Tab before attempting to use the remote. Battery Replacement 1. Remove the battery holder. 2. Insert the battery into the battery holder And insert the battery holder into the remote. Be sure to observe the correct polarity. 3.
* Function control is available on the unit and the Remote Control. ** Function not available in this model. 1. POWER* Press this button to turn the unit ON and OFF. 2. MONITOR SELECT M1 Button – Set the remote control code to allow control of the unit in M1 mode. M2 Button** – Set the remote control code to allow control of the unit in M2 mode. 3. SOURCE* Each time the button is pressed, the unit will cycle through modes DVD/USB/CARD, AV and AUX. 4.
10. DISPLAY Press to display the current disc information while the disc is playing. 11. SCAN BACKWARD (7) Press to search in a backward direction. Press repeatedly to change the search speed from 2, 4, 8, 16, 32 times and normal speed. 12. PLAY* Press to activate the play mode while a disc is loaded into the disc compartment. 13. PREVIOUS (9) Press to return to the previous chapter or track. 14. PAUSE (II) Press to pause playback. 15.
22. SETUP Press to display the Setup menu which allows the user to change the DVD player options such as LANGUAGE, VIDEO, RATING & MISC. Refer to the settings and adjustments section for more information. 23. SUBTITLE Press to display and select the subtitle language in DVD mode. Each time you press the button, the subtitle language changes. Note: The type and number of languages for subtitle vary from disc to disc. 24. REPEAT Allows the user to repeat a selected CHAPTER, TITLE, ALL or OFF. 25.
MENU ADJUSTMENT The System Menu Contains features and options that let you customize your system to change the screen mode display, OSD language and source default. 1) 2) 3) 4) 5) Press the SYSTEM MENU button on the remote, the main page of the system menu will appear on screen. Use the cursor buttons p or q to select the desired item in the main page and press the ENTER button to select. The sub menu will appear on screen.
FMM SELECT FMM ON/OFF options - Turns the wi FM Modulator on or off. FMM SELECT option - Selects the wireless FM Modulator Frequency (CH1 88.1MHz, CH2 88.3MHz, CH3 88.5MHz, CH4 88.7MHz, CH5 88.9MHz, CH6 89.1MHz, CH7 89.3MHz, CH8 89.5MHz, CH9 89.7MHz, CH10 89.9MHz, CH11 90.1MHz, CH12 90.3MHz, CH13 90.5MHz, CH14 90.7MHz, Ch15 90.9MHz, CH16 91.
SCREEN MODE SELECT This allows the user to change the screen format (aspect ratio 4:3, 16:9). To select the screen aspect ratio format highlight SCREEN MODE and press ENTER button to enter the submenu. Then press the Cursor button p or q to select from 4:3 or 16:9. Press ENTER button to confirm the setting.
MAIN PAGE TV Display The TV DISPLAY setup allows you to set the screen aspect ratio. Normal/PS General Setup Page TV Display WIDE Normal/PS This displays the wide picture on the screen with a Angle Mark OFF Normal/LB OSD Language ENG WIDE portion of the left & right side removed. Screen Saver ON Normal/LB Last Memory ON This displays the wide picture with black bands on the upper and lower portions of the screen.
Last Memory ON - DVD will have last memory when power interruption OFF - DVD will not have last memory when power interruption General Setup Page TV Display WIDE Angle Mark OFF OSD Language ENG Screen Saver ON Last Memory ON ON OFF Set Last Memory State VIDEO QUALITY SETUP TV Type Video Quality Setup The TV Type setup allows you to select the color system of the TV to be connected.
PREFERENCE PAGE The Setting in this page can only be made when the player is in the Stop mode or when there is no disc in the player. Audio Setup Select "Audio" using pqbutton, then press u Preference Page button to enter the Sub menu. Select the audio you Audio ENG English Subtitle OFF French desire using pqbutton, then press “ENTER” to Disc Menu ENG Spanish Parental German confirm the setting. Press tbutton to return.
Parental This item allows you to limit movie playback from G to ADULT. The lower the value, the more strict the control. 2 G 3 PG 4 PG 13 6 R 7 NC17 8 ADULT Preference Page Audio ENG Subtitle OFF Disc Menu ENG Parental Default 2 G 3 PG 4 PG 13 6 R 7 NC17 8 ADULT Set Parental Control Default - RESET The Default - RESET allows you to reset all options to factory settings. Note : This function will not affect the parental control settings.
Playing Audio CDs When playing an audio CD, the DISPLAY banner appears automatically. It displays the tract and the amount of time remaining for the track playing, the total amount of time on the disc and the elapsed time for the disc. Pressing the DISPLAY button on the remote consecutively changes the options of the time display.
Selecting Folders and Songs When an MP3 is loaded in the player, the navigation menu appears automatically. 1. Press p or q to move the highlight to the desired folder and press ENTER to display the songs in the folder. 2. Press p or q to move the highlight to the desired folder and press ENTER to begin playback of the highlighted song. Selecting a Play Mode You can choose what order the songs will play on a disc temporarily. The default play mode is FOLDER.
DVD Area Code The DVD player is preset to a region code at the factory depending on where the DVD player is sold. DVD from a different region cannot be played in this unit and the unit will display "WRONG REGION” DVD Basics To get the optimum use out of the DVD section, make sure you read this section completely. Types of Discs your DVD will play • DVD* disc - DVD discs which contain video. • Audio disc - Audio CDs contain musical or sound content only.
ACCESSORIES WIRELESS HEADPHONES The ODM98501 includes a built-in infrared transmitter for use with the supplied wireless headphones. The headphone volume is adjusted using the controls on each headset. Any number of wireless headphones may be used but they must be used within a line of sight from the transmitter, as infrared transmissions, like visible light travel only in a straight line. See the documentation accompanying your wireless headphones.
TROUBLESHOOTING SOLUTION PROBLEM IR remote inoperative Verify that the batteries in the remote are fresh. Verify that the remote sensor eye is not obstructed. Disc won't play Insert a disc with the label side facing upwards. Check the type of disc you put into disc tray. This DVD only plays DVD, audio CD and Mp3. Both the unit and the disc are coded by region. If the regional codes don’t match, the disc can’t be played. Play starts, but then stops immediately The disc is dirty. Clean it.
Installing The Snap On Covers 1. 2. Housing 3. Snap On Cover (Shroud) 1 Pewter, 1 Shale 4. Snap On Cover (Screen Back Cab) 1 Pewter, 1 Shale Pry Tool Place the pod on a soft surface to avoid damaging the plastic. Installing The Shroud Catch Catch (A) Begin by hooking area “A” (above) over the dome light and slide the cover over the pod. The cover will snap in place. Installing The Screen Cover (B) (B) Open the screen and hook the two tabs “B” on the bottom edge of the screen.
Removing The Snap On Cover (Shroud) From The Housing Work on a soft surface to avoid damaging the plastic. Insert the supplied pry tool between the Housing and Snap On Cover (Shroud), then press the pry tool to release the Snap On Cover (Shroud). 1. 2. 3. 4. Removing The Snap On Cover (Screen Back) From LCD The Housing Insert the supplied pry tool between the Housing and Snap On Cover (Screen Back), then press the pry tool to release the Snap On Cover (Screen Back). 1. 2. 3. 4.
WIRING DIAGRAM FM ANT Dome Light Power Source 12 Pin Power / Signal harness 2 Pin Power Wire Harness with choke Line In-L (White) Line In-R (Red) Line In-V (Yellow) Line In-L (White) Line In-R (Red) Line In-V (Yellow) AV1 Video Source 1) Make the connections to the vehicle for the 12 pin wiring harness. 2) Connect 2 pin power harness to vehicles electrical system by tapping into an accessory hot line and a good ground. 3) Connect the 12 pin harness to the mating connector on the video monitor.
CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched system. Positive switched systems supply voltage to the interior lights to turn on, negative switched systems apply ground to illuminate the bulbs.
Negative Switched Dome Lighting To 12 pin connector Red - Lamp on Black - Lamp common Purple - Lamp Auto To constant To constant Factory Door ajar switch or Body Control computer MOUNTING THE TRIM RING Roof Roof Support Headliner Mounting Bracket Self-drilling Screws Video Unit M4 Screws 26
MATERIALS INCLUDED IN THIS PACKAGE: 1) 2) 3) 4) 9", 10.
