User's Manual

ManualsBrandsActiontec Electronics ManualsComputers & Accessories54Mbps Wireless Gateway and Access Point

Questions? Call toll-free at 1-800-247-7285

Connect the Gateway to a Computer

Step 3 Plug the smaller end

of the

Power Cord into the

Black Port on the back of the

Gateway.

Step 4 Plug the larger end of

the

Power Cord into a Power

Outlet

Step 1 Get the Wireless DSL

Gateway

from your DSL

Quick Start Kit and take it out

of the bag.

Step 2 Get the Black Bag and

remove the

Power Cord from

the bag.

Wireless DSL Gateway

Power Cord

Black Port

Step 10 Get the Green DSL

Cable

out of the Black Bag.

Step 11 Plug one end of the

Green Cable into the Green

Port

on the back of the

Gateway.

Questions? Call toll-free at 1-800-247-7285

Step 5 Confirm the Power

Light

on the Gateway is Green.

Power Light on Wireless DSL Gateway

Step 13 Confirm that the

Power and DSL Lights are

solid

Green.This may take up

to 30 seconds.

Power & DSL Lights on Wireless DSL Gateway

Step 6 Get the Yellow Cable.

Step 7 Plug one end of the

Yellow Cable into the Yellow

Port

on the back of the

Wireless DSL Gateway.

Questions? Call toll-free at 1-800-247-7285

Step 8 Plug the other end

of the

Yellow Cable in the

Ethernet Port on the back of

the computer.

Ethernet Port looks similar

to a regular Phone Jack,but is

slightly larger.

Note: If the Ethernet Network Light does NOT turn green, make sure the Yellow

Cable is properly connected on both ends.

Step 9 Confirm that the

Ethernet light on the

Gateway is

Green. This may

take a few moments.

Ethernet Light on Wireless DSL Gateway

Step 12 Plug the other end of

the

Green Cable into the Phone

Jack

closest to your computer.

Questions? Call toll-free at 1-800-247-7285 Questions? Call toll-free at 1-800-247-7285

Note: If the DSL Light continues to blink,make sure you received notification from

your DSL Service Provider that your DSL service is On.Otherwise,contact your

DSL Service Provider immediately.

Questions? Call toll-free at 1-800-247-7285 Questions? Call toll-free at 1-800-247-7285 Questions? Call toll-free at 1-800-247-7285

Before proceeding,make sure you have received notification

from your phone company that your DSL line is active.

Note:

If you have a Macintosh Computer,see section 6,“Setup a Macintosh

Computer,”at the end of this Quick Start Guide.

Step 1 Open a Web browser

(Netscape Navigator or Internet

Explorer,for example).In the

address bar,enter

http://192.168.0.1,then press

Enter on the keyboard.

Step 2 The “Main Menu”screen

appears.Select

Setup/ Configuration.

Step 3 Click Non-Windows

Setup

in the left-hand column

of the “Set Up/Configuration”

screen.

Step 4 The “Actiontec DSL Modem

Setup Page”screen appears.

Follow the onscreen instructions.

Have your Internet Service

Provider

(ISP) Worksheet handy

and use it to fill in the text boxes

in the

Actiontec DSL Modem

Setup Page.

If you have not received your ISP

Worksheet,contact your ISP. The

Worksheet is provided separately

from this kit by your ISP.

Step 5 Click Save and Restart at the bottom of the Actiontec

DSL Modem Setup Page to save your changes.

The Wireless DSL Gateway is now configured and ready for

use.For more information regarding technical support, please

review the Start Here Guide.

If you received a Block of IP addresses from your Internet Service

Provider,follow the instructions in Section 4 of this Guide,

“Configure a Block of IP Addresses.”Otherwise,go to Section 5,

“Configure a Single IP Address.”

Security Notice

Don’t be a victim! Secure your DSL service from unwanted

intrusions.Please refer to the Security section of your User

Manual for more information regarding network security.

Install the Phone Filters

Step 1 Unplug your Telephones

(or other devices) from their

current

Phone Jacks.

Step 2 Open the Clear Bag

and remove the Phone Filters

from the bag.

What are Phone Filters? Phone Filters separate the DSL signal

from the voice signal,allowing you to talk on the telephone

and be online at the same time.

All Devices with the same phone number as your DSL Line

require Phone Filters.This includes telephones,fax machines,

caller ID boxes,and answering machines.

Caution: Do Not unplug the Green Cable from the Phone Jack near your Computer.

Note: The number and type of Phone Filters included in this kit may vary.

Step 3 Plug a Phone Filter

into every Phone Jack in your

house with the same phone

number as your DSL Line,and

a telephone (or other device)

connected to it.

If you need additional Phone

Filters,contact your DSL

Service Provider.

Note: If you have a wall-mount telephone,you must install the Wall-Mount Phone

Filter. For all other telephones or other devices,use the small Phone Filters.To

install a Wall-Mount Phone Filter,see “Installing a Wall-Mount Phone Filter,”below.

Step 4 Plug one end of the Phone

Cord

into the Phone Filter and

keep the other end attached to

the telephone (or other device).

Caution:Do Not connect a Phone Filter into the Phone Jack near your Computer

(the Phone Jack into which your Green Cable is plugged).

To Install a Telephone next to your Computer:

Step 1 Find the Phone Cord

connected to the Telephone next to

your Computer.Unplug this Phone

Cord from the Phone Jack it is

currently plugged into (you may

have already unplugged the cable

during the modem installation

process).Keep the other end

connected to the Telephone.

Phone

Jack

Phone

Cord

Note: Do Not unplug the Green cable from the Phone Jack near your computer.

Step 2 Plug the Phone Cord

into the Port marked “Phone” on

the back of the Gateway.

Do Not

plug the Phone Cord into the

back of your Computer.

Make sure you have connected

your Phone to the Gateway

exactly as shown in the picture to

the right.

Power

Outlet

Power

Cord

Note: The phone port on the Gateway includes a built-in microfilter.As a result,

no additional filter is needed.

Phone

Port

DSL Cable

1) Remove the wall-mount telephone from the wall jack.

2) Open the top and bottom toggles until they snap into the

open position.

3) Push the Wall-Mount Phone Filter into the wall jack,fully

inserting the plug on the back of the filter into the wall

jack opening.

4) Push the toggles back into the closed position until they

lock on the studs of the wall jack.

5) Reattach the telephone to the Wall-Mount Phone Filter.

Installing a Wall-Mount Phone Filter

Configure the Gateway

Flip this Quick Start Guide over to continue



If you are installing DSL service

and have a monitored home

security alarm,

Do Not continue

with this installation process.We

recommend calling your DSL

Service Provider for a technician

installation,or contacting your

security system provider for

further details.Please refer to

the Security section of the User

Manual for more information.

Yellow Port

Green Port

Yellow Cable

Green

Cable

QwstARK RedQS.qxd 12/2/03 11:20 AM Page 1

Summary of content (4 pages)

PAGE 1
QwstARK RedQS.qxd 1 12/2/03 11:20 AM Page 1 2 Connect the Gateway to a Computer Before proceeding, make sure you have received notification from your phone company that your DSL line is active. If you are installing DSL service and have a monitored home security alarm, Do Not continue with this installation process.We recommend calling your DSL Service Provider for a technician installation, or contacting your security system provider for further details.
PAGE 2
QwstARK RedQS.qxd 4 12/2/03 11:20 AM Page 2 Configure a Block of IP Addresses Note: The information required to configure a block of IP addresses is provided by your ISP. If this information has not been provided, contact your ISP. Step 1 Click Setup in the top menu. Step 5 Make sure the circle next to Obtain an IP Address through PPPoA is selected. Step 6 Check the box next to Unnumbered Mode.
PAGE 3
PAGE 4