Installation Guide

MyWirelessTV allows video and audio to be sent from video
source to the TV wirelessly. Therefore, you have the freedom to
place the TV virtually anywhere within the home and enjoy live
TV without the wiring mess.
Make sure you identify which ‘source device’ that you want to
connect to the Transmitter. Video from that ‘source device’ will be
transmitted to your receiver box(s).
INSTALLATION for the MyWirelessTV is EASY. Both units come
pre-paired to work with each other. All you need to do is connect
the cables according to the diagram or, if you want, follow the
detailed step-by-step instructions.
A
How MyWirelessTV Works
Step
1b (Optional) If the source device is
previously connected to an HDTV, unplug
the HDMI cable from the back of the
source, then plug the free end of the HDMI
cable into the HDMI port that labels
Out-to-TV on the back of the Transmitter.
Step
1c Otherwise, get an HDMI cable
from MyWirelessTV 2 Kit. Plug one end
into the HDMI Input port on the back of
the Transmitter.
Step
1a Select the Source Device (i.e. a Cable/Satellite set-top
box or Blu-ray player) you wish to transmit signal to the TV, and
power off that device. Get the Wireless HD Video Transmitter
unit from MyWirelessTV 2 Kit and follow the steps below.
B
Setting Up Transmitter & Receiver
Step
3a Get the Wireless HD Video
Receiver, HDMI cable and power
supply. Go to the TV that you want to
connect.
Step
3b Plug one end of this HDMI
cable into an HDMI port on the HDTV.
Step
2a Get the power supply from MyWirelessTV 2 Kit.
Plug the smaller end of the power supply into the 5VDC port
on the back of the Transmitter.
Step
3d Turn on the TV and switch the source to the HDMI
input that the Receiver is connected to.
Step
4a Plug the smaller end of the
power supply into the 5VDC port on
the back of the Receiver.
Step
3c Plug the other end of the
HDMI cable into the HDMI port labels
Out-to-TV on the back of the Re-
ceiver.
Step
4b Plug the larger end of the
power supply into a power outlet.
Step
4c Make sure the Power Light
on the Receiver is SOLID Green.
Flip this Quick Start Guide over to continue
NEXT
Note: Only use power adapter, Actiontec Electronics Inc., Model # WA-10P05FU
Note: The LINK light will blink.
Up to
150 ft.
range*
RECEIVER MWTV2RX
TRANSMITTER MWTV2TX
HDTV
(Optional)
(Optional)
(Optional)
HDTV
POWER
OUTLET
POWER
OUTLET
SOURCE
DEVICE
2
1b
4
3
5
6
Please refer to
this illustration
while connecting
cables
Step
4d Wait for a bit as the Receiver
connects to the Transmitter. The LINK
light should show SOLID Green once
they’re connected.
CAUTION
Do NOT place the MyWirelessTV
Transmitter or Receiver on top of
or near a heat-generating source.
*Range subject to change. Walls, ceilings
and floors may reduce the wireless range.
Step
1d Plug the other end into the
HDMI port on the Source Device.
Step
2b Plug the larger end of the
power supply into a power outlet.
Step
2c Verify the Power Light on
the Transmitter is SOLID Green.
Note: If the Transmitter and Receiver are in the same room, you
may skip to Step 1c.
Step
2a Get the power supply from
MyWirelessTV 2 Kit. Plug the smaller end
of the power supply into the 5VDC port
on the back of the Transmitter.
1c
1d
Step
2d Now power on your video Source Device.
pic
MWTV2_QSG-0530-0731-000-v5_QS sngl pnl 2014/5/5 16:37 页 1