Installation Guide

MyWirelessTV 2
Multi-Room Wireless
HD Video Kit
NEXT
Model# MWTV2TX & MWTV2RX
D
Troubleshooting
C
Setting Up IR Control (Optional)
Quick Start Guide
This Quick Start Guide will walk you through the easy steps
to set up MyWirelessTV 2 Kit.
A
How MyWirelessTV Works
B
Setting Up Transmitter & Receiver
C
Setting Up IR Control
D
Troubleshooting
You will need the following items from your MyWirelessTV 2 kit:
•
Wireless HD Transmitter
•
Wireless HD Receiver
•
Two (2) Power Supplies
•
Two (2) HDMI Cables
•
IR Blaster Cable
•
IR Receiver Extension Cable
© 2014 Actiontec Electronics, Inc. Actiontec, Actiontec Installation Buddy, Creative Solutions for the Digital Life,
and the Actiontec logo are trademarks or registered trademarks of Actiontec Electronics, Inc. in the U.S. or other
countries. All other names are properties of their respective owners.
Product photo may differ from actual product, however functionality remains as stated above.
Specifications are subject to change without notice.
FREQUENTLY ASKED QUESTIONS
1
Q
Do I must connect a TV to the Transmitter’s HDMI Out-
to-TV port?
A
No. This step is optional.
2
Q
I’m not seeing video on the TV that’s connected to the
Transmitter.
A
Check the power and connection from the video source to
the Transmitter, and the connection from the Transmitter
to TV.
3
Q
I’m not seeing video on the TV that’s connected to the
Receiver.
A
Check the power and connection from Receiver to the TV,
and make sure the correct source input is selected on the
TV.
4
Q
The audio and video on the Receiver’s TV seems
slower than on Transmitter’s TV.
A
This is expected since the Receiver receives AV transmis-
sion from the Transmitter over the air.
Your HDTVs and cable/satellite box should be connected as
shown in the previous diagram. You can now start enjoying
HDTV anywhere you want it!
Step
6b Plug the IR Extender cable’s
green connector in to the Green port
on the back of the Receiver.
5
Q
The video quality is poor and sometimes there’s no
video displays on the Receiver’s TV.
A
You may need to adjust the orientation of the Transmitter
and Receiver units, and direct them to be facing each
other. You can view the MyWirelessTV connection
strength on the Menu page of the Receiver. To access the
Menu page, press the MENU button once on the Receiver.
6
Q
I cannot control the source device with its remote con-
trol, via the MyWirelessTV Receiver OR the source de-
vice is slow to respond to the remote control.
A
Make sure the IR Blaster cable is connected to the Trans-
mitter “IR Transmit” port, and the sensor is mounted di-
rectly on top of the source device’s IR Sensor window.
Also make sure the Receiver or the IR Receiver cable sen-
sor is in line-of-sight of the remote control.
7
Q
What is the MENU button on the Receiver?
A
The MENU button provides access to the Menu screen.
You can view the device firmware version, signal strength,
change the language for display and video stream mode.
Step
5d Locate the Infrared (IR) sensor
on your source device box, and mount the
IR Blaster head on top of the box over the
sensor of the source device.
Step
6a Get the IR Extender cable
(with a green connector) from the
MyWirelessTV 2 kit.
Step
5a Get the IR Blaster cable
from MyWirelessTV 2 kit. The IR Blaster
cable has a black connector.
Step
5b Plug the IR Blaster cable’s
black connector into the Transmit port
on the back of the Transmitter.
Step
5c Remove the adhesive tape from the bottom of the
IR Blaster head.
Part No: 0530-0731-000 QS1155/0811
The IR Blaster Cable connects to your Wireless HD Video
Transmitter. The IR Blaster can receive IR signal from your
Source Device’s remote control over MyWirelessTV network, and
emits the IR signal to control the Source Device. Thus, you can
control the Source Device from wherever the TV and Wireless HD
Video Receiver are located.
The IR Receiver Extension Cable extends the IR receiver of the
Wireless HD Video Receiver. Thus, it allows the Receiver to
receives IR signal from the remote control, if the unit is placed in
an area where IR signal is not in line-of-sight of the source’s
remote control. Use of this cable is optional.
Note: If the Receiver and Transmitter are in the same room,
setting up IR Blaster cable is not required.”
For Technical Support call
1-888-436-0657
How to Videos, User Manual, Latest Firmware and additional
information are available Online at
http://www.actiontec.com/mwtv2
Step
6c Remove the protective cov-
ering of the double stick tape and at-
tach the flat end of the IR Extender
cable to the front corner of the HDTV
bezel or frame.
MWTV2_QSG-0530-0731-000-v5_QS sngl pnl 2014/5/5 16:37 页 2