Owner's manual

ManualsBrandsActiveforever ManualsHealth and hygieneMettler Sonicator Plus 994 4-Channel Combination Therapy Device

Sonicator

Plus 994 Specifications

General Specifications:

Input: 90–240 VAC, 50–60 Hz, 2.3 Amp. Nom.

Certification:

Domestic model

The Sonicator Plus 994 complies with the ultrasound

performance standards set forth in the Code of Federal

Regulations, Title 21 (Food and Drugs), Part 1050.10 and

IEC 601-2-5, 1

Ed., 1984

ETL and C-ETL Listed:

Domestic model

Model ME 994 (9801427)

Classification: Protective Class I Equipment

CE model

Type BF Equipment

Enclosed equipment without protection against ingress of

water.

Equipment not suitable for use in the presence of a

flammable anesthetic mixture with air or with nitrogen oxide

Year 2000 Compliant Yes

U.S. Patent Numbers: U.S. and foreign patents applied for and granted including

U.S. Patent Numbers 4,966,131 and 5,095,890.

Weight: 10.7 pounds

4,9 kg

Dimensions: 5 in (H) x 14.5 in (W) x 10 in (D)

12.7 cm (H) x 36.8 cm (W) x 25.4 cm (D)

Operating Temperature: +50°F to +104°F

+10°C to +40°C

Humidity:

Operating, 30% to 75% Relative Humidity at 104°F (40°C)

Nonoperating, 5 to 95% Relative Humidity, non-condensing

Storage Temperature: -40°F to 167°F

-40°C to 75°C

Storage Humidity: Storage, 30% to 90% Relative Humidity at 40º C, Non-

condensing

Storage Pressure: 700-900 mB

Environmental Disposal: The device contains lead in the form of solder used to

produce electrical contact between components. To avoid

adverse environmental impact, utilize a disposal facility that

performs complete incineration of the device at a temperature

in excess of 1000°C.

The shipping materials are fabricated of cardboard and may

be disposed of with other paper products.

Summary of content (8 pages)

PAGE 1
Sonicator® Plus 994 Specifications General Specifications: Input: 90–240 VAC, 50–60 Hz, 2.3 Amp. Nom. Certification: Domestic model The Sonicator Plus 994 complies with the ultrasound performance standards set forth in the Code of Federal Regulations, Title 21 (Food and Drugs), Part 1050.10 and IEC 601-2-5, 1st Ed.
PAGE 2
Treatment timer: Timer Accuracy: ±0.5 minutes for times less than 5 minutes ±10% for times from 5 to 10 minutes ±1.0 minute for times greater that 10 minutes ±5%, CE specification Maximum Treatment Time: 60 minutes–electrical stimulation 30 minutes–ultrasound or combination therapy Treatment Timer: Treatment time counts down to zero when a time is set, or up to 60 or 30 minutes when no time is set. The digital timer indicates time in minutes and seconds.
PAGE 3
Pulse Width 2 ms Output 1, 3.2 or 3.3 MHz Ultrasound Pulse Space 10 ms Time Figure 3.1—Pulse Waveform—20% Duty Cycle 1, 3.2 or 3.3 MHz Ultrasound 5 ms Output Pulse Width Pulse Space Time 10 ms Figure 3.2—Pulse Waveform—50% Duty Cycle In the continuous mode, the power is on at least 95% of the time the timer is running. The continuous mode waveform is shown below: Output 1, 3.2 or 3.3 MHz Ultrasound Time Figure 3.
PAGE 4
the applicator face. A few inches from the face, it is a single smooth bell-shaped curve. Nearer the face the pattern varies more due to phase cancellations. Sample curves measured in the far field from the surface are shown in Figures 3.3, 3.4, 3.5 and 3.6. Figure 3.4—10 cm² Applicator (1 MHz), ME 7310,—Three Dimensional Beam Pattern Figure 3.5—5 cm² Applicator (1 MHz), ME 7513—Three Dimensional Beam Pattern Figure 3.6—5 cm² Applicator (3.2 MHz), ME 7513—Three Dimensional Beam Pattern Figure 3.
PAGE 5
Waveform Specifications: Interferential Mode Waveform Type: Polarity: Volts: Current: Figure 3.8— Interferential Waveform Average current at maximum intensity and frequency: Maximum current density under 2" diameter electrode. Frequency: Frequency Modulation: Phase Duration: Available Amplitude Modulation Options: Sinewave None 0–65 volts RMS, 1 Kohm load 0–65 mA RMS, 1 Kohm load 65 mA RMS 3.
PAGE 6
4–1,000 ms beat envelope Available Amplitude Modulation Options: Continuous Surge Reciprocation Available Channels: All Waveform Type: Polarity: Volts: Current: Average current at maximum intensity and frequency: Maximum current density under 2" diameter electrode. Frequency: Burst modulated sine wave None 0–50 volts RMS, 1 Kohm load 0–50 mA RMS, 1 Kohm load Medium Frequency Mode Figure 3.
PAGE 7
Phase Duration: Available Amplitude Modulation Options: 50–300 µs Available Channels: All Waveform Type: Polarity: Volts: Current: Average current at maximum intensity and frequency: Monophasic twin peak Positive or negative 500 volts peak, 1 Kohm load 0–500 mA peak, 1 Kohm load Continuous Surge Reciprocation High Volt Mode 500 volts 8 us 50 % 0 volts 75 us Figure 3.12—High Volt Waveform 1.2 mA at 120 pps with 1 Kohm load Maximum current density under 2" diameter electrode.
PAGE 8
Available Amplitude Modulation Options: Continuous Available Channels: Channel Two only Amplitude Modulation Specifications: Vector rotation: Interferential Mode Only -50% amplitude modulation in anti phase with an eight second modulation period.