CP9575 Actron AutoScanner OBD II Scan Tool ® ENGLISH
Contents Safety Precautions...............................................................3 Signal Words Used...............................................................3 About the Tool......................................................................4 Tool Parts..............................................................................4 Icons......................................................................................5 Connect the Tool.....................................................
Safety Precautions This User’s Manual describes the features of the Tool and provides step-by-step instructions for operating the Tool. Always refer to and follow safety messages and test procedures provided by the manufacturer of the vehicle and the T ool. Read the User’s Manual completely before operating the Tool. An undetected or uncorrected vehicle malfunction could cause a serious, even fatal, accident.
• Most vehicles are equipped with air bags. If you elect to work around air bag components or wiring, follow your vehicle service manual cautions. You could be seriously injured or killed by an unintended deployment. The air bag can still open several minutes after ignition is turned off. • Always follow vehicle manufacturer’s warnings, cautions, and service procedures. About the Tool The Tool allows you to retrieve and erase/reset diagnostic data from the vehicle control module.
ENTER key Selects displayed items. BACK key Returns to the Main Menu or previous screen. OBD II Connector Connects the Tool to the vehicle connector. Icons The following icons may appear on the display: Indicates additional information is available on next screen by using the ERASE key. Indicates additional information is available on previous screen by using the READ key. CONFIRMED PENDING PERMANENT Confirmed codes are reported when a component is indicating a malfunction is present.
The Tool automatically reads Codes and I/M Monitors and displays the data. When done viewing data, press BACK key to return to Main Menu. Diagnostics Menu User Interface To select functions: 1. From the Diagnostic Menu, press the READ or ERASE arrow key until the desired function is highlighted, then press the ENTER key to retrieve and display the results. DIAGNOSTIC MENU ==================== Read Codes Erase Codes MIL Status State OBD Check View Data View Freeze Data ^^ 2.
Vehicle Selection Vehicle Selection will be displayed for Read Codes when a manufacturer specific DTC is retrieved from the vehicle. Erase Codes The Erase function performs the following: 99 Erases Codes (both Confirmed and Pending DTCs). Permanent codes can only be erased by the vehicle. 99 May erase Freeze Data results depending on the vehcle. 99 Sets I/M Monitors to not ready. Perform Erase Codes function only after systems have been checked completely and DTCs have been written down.
I/M Monitors (Emissions) Inspection / Maintenance Monitors provide a snapshot of the Emission System operations by indicating that the I/M Monitors are Ready or Not Ready. For an I/M Monitor to be Ready, the vehicle must have completed a drive cycle (been driven long enough under proper conditions to have completed a drive cycle). A Monitor must be listed as Ready to pass an emissions test. If an I/M Monitor is Not Ready, it is because a drive cycle has not completed.
This Drive Cycle - shows status of monitors since the start of the current drive cycle. Refer to the vehicle service manual for more detailed information on emission-related monitors and their status. 99 Some vehicles do not support This Drive Cycle. If vehicle supports both types of monitors the I/M Monitors Menu displays.
• • • • Operation of the keypad to be checked, Memory of the Tool to be checked, Language to be changed, Units of measure to be changed. State OBD Check (Emissions) The State OBD Check function is used to display a basic status of the vehicle’s OBD system.
Updating Your Tool 1. Download Scanning Suite from http://www.Actron.com/downloads/. 2. Install Scanning Suite. 3. Connect USB Cable to Tool and PC. If tool displays PROGRAM MODE, PROGRAM MODE proceed to step 4. See User Manual If tool displays DIAGNOSTIC MENU, select SYSTEM SETUP. From the system setup menu, select PROGRAM MODE and then proceed to step 4. 4.
Tool ABS FRP Description Absolute Fuel Rail Pressure ABS LOAD Absolute Load Value ABS TPS B, C Throttle Position B, C ABSLT TPS Absolute Throttle Position ACC POS D Accelerator Pedal D, E, F ACC POS REL Relative Accelerator Pedal Position AECD1_TIME1, TIME 2 Total Run Time with EI-AECD #1 Timer 1 Active, #2 Timer Active AECD10_TIME1, TIME 2 Total Run Time with EI-AECD #10 Timer 1 Active, #2 Timer Active AECD11_TIME1, TIME 2 Total Run Time with EI-AECD #11 Timer 1 active, #2 Timer Active AE
Tool Description CACT 11, 12 Charge Air Cooler Temperature Bank 1 Sensor 1 supported, Sensor 2 supported CACT 21,22 Charge Air Cooler Temperature Bank 2 Sensor 1 supported, Sensor 2 supported CALC LOAD Calculated Engine Load CAT TEMP11, TEMP12 Catalytic Converter Temp Bank1, Temp Bank 3 CAT TEMP21, TEMP22 Catalytic Converter Temp Bank2, Temp Bank 4 CLR DIST Distance since erase CLR TIME Minutes Run since Erase CLR TRPS Warmups Since Erase CMD EQ RAT Commanded Equivalence Ratio COOLANT E
Tool Description EGR_A_ERR, B_ERR EGR A Error, B Error EGRT 11, 21 Exhaust Gas Recirculation Temperature Bank 1 Sensor 1, Bank 2 Sensor 1 EGRT 12, 22 Exhaust Gas Recirculation Temperature Bank 1 Sensor 2, Bank 2 Sensor 2 EGT 11, 21 Exhaust Gas Temperature (EGT) Bank 1 Sensor 1, Bank 2 Sensor 1 EGT 12, 22 Exhaust Gas Temperature (EGT) Bank 1 Sensor 2, Bank 2 Sensor 2 EGT 13, 23 Exhaust Gas Temperature (EGT) Bank 1 Sensor 3, Bank 2 Sensor 3 EGT 14, 24 Exhaust Gas Temperature (EGT) Bank 1 Sensor
Tool Description IAT 12, 22 Intake Air Temperature Sensor Bank 1 Sensor 2, Bank 2 Sensor 2 IAT 13, 23 Intake Air Temperature Sensor Bank 1 Sensor 3, Bank 2 Sensor 3 ICP_A, B Injection Control Pressure A, B ICP_A_CMD, B_CMD Commanded Injection Control Pressure A, B IDLE_TIME Total Idle Run Time IGN ADV Timing Advance LAMBDA11, 21 02 Sensor Lambda Bank 1 Sensor 1, Bank 2 Sensor 1 LAMBDA12, 22 02 Sensor Lambda Bank 1 Sensor 2, Bank 2 Sensor 2 LT FTRM1 Long Term Fuel Trim 1 or 3 LT FTRM2 Lo
Tool Description PM 11, PM 21 PM Sensor Mass Concentration Bank 1 Sensor 1, Bank 2 Sensor 1 PNTE_Stat PM NTE control area status PTO STATUS PTO Status PTO_STAT Power Take Off (PTO) Status PTO_TIME Total Run Time With PTO Active REAG_DEMD Average Demanded Reagent Consumption REAG_LVL Reagent Tank Level REAG_RATE Average Reagent Consumption REL FRP Relative Fuel Rail Pressure REL TPS Relative Throttle Position RUN_TIME Total Engine Run Time SCR REAG DEV, DEV1, DEV2, DEV3, DEV4 SCR ind
Tool Description TCA_CINT, TCB_CINT Turbocharger A Compressor Inlet Temperature, Turbocharger B TCA_COUT, TCB_COUT Turbocharger A Compressor Outlet Temperature, Turbocharger B TCA_RPM, TCB_RPM Turbocharger A RPM, B RPM TCA_TCOUT, TCB_TCOUT Turbocharger A Turbine Outlet Temperature, Turbocharger B TCA_TINT, TCB_TINT Turbocharger A Turbine Inlet Temperature, Turbocharger B THROT CMD Commanded Throttle Actuator Control TP G Absolute Throttle Position G TQ_ACT Actual Engine - Percent Torque TQ
Declaration of Conformity: This product is declared to be in compliance with the European RoHS Directive 2002/95/EC which restricts the following substances in electrical and electronic equipment: Substance Maximum Concentration Cadmium (Cd) 100 ppm Hexavalent Chromium (CrVI) 1000 ppm Lead (Pb) 1000 ppm Mercury (Hg) 1000 ppm Polybrominated Biphenyls (PBB) 1000 ppm Polybrominated Diphenyl Ethers (PBDE) 1000 ppm This product is declared to conform to the following standard under the EMC directiv
Bosch Limited Warranty THIS WARRANTY IS EXPRESSLY LIMITED TO ORIGINAL RETAIL BUYERS OF BOSCH ELECTRONIC DIAGNOSTIC TOOLS (“UNITS”). Bosch Units are warranted against defects in materials and workmanship for one year (12 months) from date of delivery. This warranty does not cover any Unit that has been abused, altered, used for a purpose other than that for which it was intended, or used in a manner inconsistent with instructions regarding use.
©2013 Bosch Automotive Service Solutions LLC 0002-001-3106 REV.
