User Guide

ManualsBrandsActron ManualsAutomotiveAutoScanner Plus OBD II Scan Tool for All 1996 and Newer and Select 1994-95 vehicles - Includes ABS and Airbag Features for Select Applications

Table Of Contents

1 Safety Precautions

CP9680 AutoScanner® Plus

en User guide

Summary of content (52 pages)

PAGE 1
CP9680 AutoScanner® Plus en User guide
PAGE 2
en | 2 | User guide | CP9680 AutoScanner® Plus Serial No: ___________________________________ SW ID: ______________________________________ HW Ver: _____________________________________ Boot Ver: ____________________________________ Prod ID: _____________________________________ Board ID: ____________________________________ Burn Date: __________________________________ Record the above information about your tool. The information is available at Main Menu --> System Setup --> Tool Information.
PAGE 3
CP9680 AutoScanner® Plus | User guide | 3 | en Table of Contents 1 Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . 5 1.1 Read All Instructions. . . . . . . . . . . . . . . . . 5 1.2 Safety Messages . . . . . . . . . . . . . . . . . . . . 5 2 Important Safety Warnings and Instructions. . . 5 3 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1 Introduction. . . . . . . . .
PAGE 4
en | 4 | User guide | CP9680 AutoScanner® Plus 573102 | REV. B | 03.2016 Bosch Automotive Service Solutions Inc.
PAGE 5
CP9680 AutoScanner® Plus | User guide | 5 | en 1 Safety Precautions For your safety, read this manual thoroughly before operating your scan tool. Always refer to and follow safety messages and test procedures provided by the manufacturer of the vehicle or equipment being tested. The safety messages presented below and throughout this user’s manual are reminders to the operator to exercise extreme care when using this test instrument. 1.
PAGE 6
en | 6 | User guide | CP9680 AutoScanner® Plus WARNING WARNING Risk of poisoning. • Use this scan tool in locations with mechanical ventilation providing at least 4 air changes per hour. Engine exhaust contains odorless gas which can be lethal. • Route the exhaust outside while testing with the engine running. Poisoning can result in death or serious injury. Risk of flying particles. • Safety goggles and protective gloves must be worn by the operator and any bystanders while using electrical equipment.
PAGE 7
CP9680 AutoScanner® Plus | User guide | 7 | en WARNING CAUTION Engine compartment contains electrical connections and hot or moving parts. • Keep yourself, test leads, clothing and other objects clear of electrical connections and hot or moving engine parts. • Do not wear watches, rings, or loose fitting clothing when working in an engine compartment. • Do not place tools or test equipment on fenders or other places in engine compartment.
PAGE 8
en | 8 | User guide | CP9680 AutoScanner® Plus 3 Getting Started 3.1 Introduction The scan tool was developed by experts in the automotive service industry to help diagnose vehicles and assist in troubleshooting procedures. The scan tool monitors vehicle events and retrieves codes from the vehicle’s control modules to help pinpoint problem areas.
PAGE 9
CP9680 AutoScanner® Plus | User guide | 9 | en more information on OBDII connectors, go to http:// www.obdclearinghouse.com/oemdb. • • DTCs consist of a five-digit alphanumeric code. The DTCs format and general code types are shown below. 1. OBD II Data Link Connector (DLC) Pins 1 8 2. 3.
PAGE 10
en | 1 0 | User guide | CP9680 AutoScanner® Plus 4 Using the Scan Tool 4.1 The Scan Tool vides power to the scan tool when reprogramming from a personal computer or off-vehicle reviewing of codes and printing. 4.2 Specifications Color, backlit, QVGA resolution Display 1 Operating Temperature 0 to 50°C (32 to 122°F) Storage Temperature -20 to 70°C (-4 to 158°F) Internal Power 4-AAA batteries External Power 7 to 16 Volts A minimum of 8.
PAGE 11
CP9680 AutoScanner® Plus | User guide | 11 | en CAUTION Do not soak keypad as water might find its way inside the scan tool. 4.4 Power Internal Battery • Battery power is not required to use tool. • ON/OFF button on Scan Tool turns tool on and off. • Press and hold ON/OFF for at least 1 second to turn on Scan Tool. • The Scan Tool will automatically turn OFF after a user-selectable period of inactivity when powered from the internal batteries. The default is 2 minutes.
PAGE 12
en | 1 2 | User guide | CP9680 AutoScanner® Plus Measurement Units English Metric 3. Quick Test Quick Test is a feature of the tool that occurs the first time the tool establishes communication with the vehicle after vehicle selection. Quick Test will display the results of I/M Monitors and Read Codes. From System Setup screen: 1. Select Quick Test. • Use the UP and DOWN keys until Quick Test is highlighted. • Press . System Setup Save measurement setting. • Press .
PAGE 13
CP9680 AutoScanner® Plus | User guide | 13 | en • Press Language Setup . English Español Francais System Setup English/Metric Auto-Power Off Quick Test Print Header Language Setup Long PID Names Pre-Trigger Setup Tool Information Display Test 3. 2. Select desired Print Header choice. • Use the UP and DOWN keys until desired choice is highlighted. Print Header ON OFF Save Language Setup setting. • Press . NOTE: When Spanish or French translation is not known, English will be shown.
PAGE 14
en | 1 4 | User guide | CP9680 AutoScanner® Plus System Setup Pre-Trigger Setup This function is used to configure how many Pre-Trigger frames are stored prior to beginning a recording. Pre-Trigger frames are the negative frames when you are playing back a recording. From System Setup screen: 1. Select Pre-Trigger Setup. • Use the UP and DOWN keys until PreTrigger Setup is highlighted. • Press .
PAGE 15
CP9680 AutoScanner® Plus | User guide | 15 | en System Setup English/Metric Auto-Power Off Quick Test Print Header Language Setup Long PID Names Pre-Trigger Setup Tool Information Display Test 2. 3. Start Display Test. • Press . Look for missing spots. • The first screen displayed says, “Check for missing spots in the display.” Display Test Check for spots in the display Press BACK to exit • Solid red, green, and blue screens are displayed. • 4.
PAGE 16
en | 1 6 | User guide | CP9680 AutoScanner® Plus System Setup –– Quick Test Print Header Language Setup Long PID Names Pre-Trigger Setup Tool Information Display Test Keypad Test Memory Test 2. –– –– Memory Test INT RAM INT FLASH Press a key. • Key name or scroll direction should inverse colors on display. • will return the tool to the System Setup screen. Keypad Test CODE BACK If no problems were detected, then “Passed” is displayed. If RAM fails, an error message is shown.
PAGE 17
CP9680 AutoScanner® Plus | User guide | 17 | en tool can be powered from vehicle or PC using USB to use the Review Data function. 1. Select Review Data. • Use the UP and DOWN keys until Review Data is highlighted. • Press . Main Menu Vehicle Diagnostics Acronyms Review Data Print Data Code Lookup System Setup This function is very similar to View Data. The only difference is that View Data is real-time viewing of PIDs, while Recording is a viewing of previously recorded PIDs.
PAGE 18
en | 1 8 | User guide | CP9680 AutoScanner® Plus 0.0 3.5 95 692 OPEN OPEN 75 4.5 3.1 ABSLT TPS(%) CALC LOAD(%) COOLANT(°F) ENG SPEED(RPM) FUEL SYS 1 FUEL SYS 2 IAT(°F) IGN ADV(°) LT FTRM1(%) Frame: 0 Throttle position –– • • Time: 0.0 If graphing is available for selected PID, the “ ” icon is located on the side of the screen. –– Press to select PIDS to graph. –– Use the UP and DOWN arrow keys to highlight the second PID to graph and then press the RIGHT arrow to select.
PAGE 19
CP9680 AutoScanner® Plus | User guide | 19 | en • • • • 3. 4.7 Use the UP and DOWN keys. Press . The Print Data menu shows a check mark next to the items that have data. If there isn’t a checkmark next to the item, then this item can’t be selected until the appropriate function is run from the Diagnostic Menu. Vehicle? OBDII/EOBD US Europe Asia Prev: 06 Accord Prev: 04 Express 1500 Prev: 04 Express 1500 Prev: 04 Express 1500 Return to Select Print Data screen. • Press . Code Lookup 3.
PAGE 20
en | 2 0 | User guide | CP9680 AutoScanner® Plus 5. Press again to return to the Diagnostic Menu. Main Menu 4.8 Locating the OBD II Data Link Connector (DLC) Vehicle Diagnostics Acronyms Review Data Print Data Code Lookup System Setup • The OBDII data link connector (DLC) is usually located under the driver’s side dash. • Refer to vehicle user manual for DLC location. • For more information, go to http://www.obdclearinghouse.com/oemdb.
PAGE 21
CP9680 AutoScanner® Plus | User guide | 21 | en • • If NO is selected, the Tool proceeds to manual selection. Press . Turn Key Off VIN 1GCFG15T541238036 Please turn the key off for 10 seconds then turn the key on. 2004 Chevrolet Express 1500 5.3 Press ENTER to continue Is this correct? Yes 5. • No If Manual was selected in Step 1, use the DOWN keys to select: • OBDII/EOBD • US • Europe • Asia • Previous Vehicle: • Press .
PAGE 22
en | 2 2 | User guide | CP9680 AutoScanner® Plus CodeConnect® information. The power of CodeConnect® is that repair information is vehicle and trouble code specific and is based on the largest experiencebased database available. CodeConnect® information is available whenever is visible on the display. It has the potential of being displayed while trouble codes are being displayed from Read Codes or while Viewing Freeze Frame data.
PAGE 23
CP9680 AutoScanner® Plus | User guide | 23 | en From the Main Menu or Diagnostic Menu. 1. Select Acronyms. • Use the UP and DOWN keys until Acronyms is highlighted. • Press . # Of Emiss Number Of Emission Related DTC Main Menu Vehicle Diagnostics Acronyms Review Data Print Data Code Lookup System Setup 4.14 2. Select the alphabetical group range for the desired acronym. • Use the UP and DOWN keys until the desired group range is highlighted. • Press .
PAGE 24
en | 2 4 | User guide | CP9680 AutoScanner® Plus 3. Select the component. • Use the UP and DOWN keys until the desired component is highlighted. • Full component name will scroll on bottom of screen for the highlighted component. • Press .
PAGE 25
CP9680 AutoScanner® Plus | User guide | 25 | en During normal driving conditions, the vehicle computer scans the emission system. After a specific amount of drive time (each monitor has specific driving conditions and time required), the computer monitors decide if the vehicles emission system is working correctly or not as well as detecting out of range values. When the monitor status is: • ok - vehicle was driven enough to complete the monitor.
PAGE 26
en | 2 6 | User guide | CP9680 AutoScanner® Plus PM Filter Mon 3. 5.2 Particulate matter filter monitor Read Codes Return to Special Tests Menu. • Press . Read Codes The Read Codes function allows the scan tool to read the DTCs from the vehicle’s control modules. DTCs are used to help determine the cause of a problem or problems with a vehicle. These codes cause the control module to illuminate the malfunction indicator lamp (MIL) when emission-related or driveability fault occurs.
PAGE 27
CP9680 AutoScanner® Plus | User guide | 27 | en Confirmed codes are reported when a component, sensor, or other part of the vehicle is indication a malfunction is present. Codes transmitted through the PCMs data stream when a trouble condition is acCurrent tive and cannot be erased. The problem must be repaired to remove the DTC. Indicates the current code has been set Intermittent at least once but possibly not enough to cause a history code to be stored.
PAGE 28
en | 2 8 | User guide | CP9680 AutoScanner® Plus ----- Diagnostic Codes 1/1 ECM Read Codes Erase Codes View Freeze Data Component Locator Acronyms Review Data Print Data Code Lookup System Setup EGR Position High MIL CODE 213 Active is a DTC that was present at the time of scan tool request. P0113 • If diagnostic results and codes are not to be erased select NO and press .
PAGE 29
CP9680 AutoScanner® Plus | User guide | 29 | en Select Module MIL is OFF OBDII/EOBD Engine ABS Airbag MIL lamp should be OFF engine is running Press ENTER to continue 4. Observe “Command sent” message is displayed. • Press . Erase Codes Command sent Codes remaining:0 Press ENTER to continue 5. Return to Diagnostic Codes Menu. • 5.4 Press . MIL Status From Special Tests Menu: 1. Select MIL Status. • Use the UP and DOWN keys until MIL Status is highlighted. • Press .
PAGE 30
en | 3 0 | User guide | CP9680 AutoScanner® Plus State OBD Check MIL Status Codes Found Monitors OK Monitors Inc Monitors N/A • OFF 0 3 4 4 If one or more control module stops responding, the scan tool displays a message. –– If continuing, dashes will replace data in right-hand column. –– If NO is selected, then the scan tool attempts to re-establish communication with that module. Validating PIDs 3. 5.6 Return to Special Tests Menu. • Press .
PAGE 31
CP9680 AutoScanner® Plus | User guide | 31 | en ABS LOAD(%) ABSLT TPS($01) ABSLT TPS($07) ACC POS D(%) BARO PRS(”HG) CALC LOAD(%) CALC LOAD(%) CAT TEMP11(°F) CLR DIST(mi) CLR DIST(mi) Select Data to View 0.0 6.3 6.3 0.0 29.2 0.0 0.0 73 499 513 Entire Data List Custom Data List English/Metric Absolute Load Value If Long PID Names is turned ON, the expanded text for the PID will scroll on the bottom line of display. See “Long PID Names” in section 3.
PAGE 32
en | 3 2 | User guide | CP9680 AutoScanner® Plus ABS TPS B(%) MIL STATUS 0.0 Off Validating PIDs Validating PID List PID 116/329 Please Wait Throttle Position B If the icon displays while a PID is selected press to view graph. Press to Return to PID Screen. Refer to “View Entire List.” on page 4-19 for instructions on how to select PIDs to graph and how to view graph. 5. Return to Select Data to View Menu. • Press . 6. Return to Datastream Menu. • Press . 5.7 3.
PAGE 33
CP9680 AutoScanner® Plus | User guide | 33 | en Record Data TROUB CODE FUEL SYS 1 FUEL SYS 2 CALC LOAD(%) COOLANT (°F) ST FTRM1(%) LT FTRM1(%) MAP(”HG) ENG SPEED(RPM) VEH SPEED(MPH) Playback data? Yes No P2122 N/A N/A 0.0 -40 0.0 0.0 28.1 0 0 Definition that caused Freeze Fra 5.8 View Freeze Data When an emission-related fault occurs, certain vehicle conditions are recorded by the on-board computer. This information is referred to as freeze frame data.
PAGE 34
en | 3 4 | User guide | CP9680 AutoScanner® Plus • Vehicle computer module losing power (on some vehicles). From Special Tests Menu: 1. Select Drive Cycle Monitor. • Use the UP and DOWN keys until Drive Cycle Monitor is highlighted. • Press .
PAGE 35
CP9680 AutoScanner® Plus | User guide | 35 | en 5.10 O2 Monitor Tests OBDII regulations require applicable vehicles monitor and test oxygen (O2) sensors to determine problems related to fuel and emissions. The O2 Monitor Tests allows retrieval of completed O2 sensors monitor test results. • The O2 Monitor Tests is not an on-demand test. O2 sensors are not tested when selected via the menu. O2 sensors are tested when engine operating conditions are within specified limits.
PAGE 36
en | 3 6 | User guide | CP9680 AutoScanner® Plus Test $03 Special Tests ID MOD MAX MEAS MIN STS I/M Monitors Drive Cycle Monitor State OBD Check MIL Status O2 Monitor Tests Diagnostic Monitor Tests On-Board Systems Vehicle Information Charging System Monitor • • 2. Applicable diagnostic monitor tests are displayed. Review test results displayed on scan tool. • Use the UP and DOWN keys until desired result is highlighted. • Press .
PAGE 37
CP9680 AutoScanner® Plus | User guide | 37 | en Special Tests I/M Monitors Drive Cycle Monitor State OBD Check MIL Status O2 Monitor Tests Diagnostic Monitor Tests On-Board Systems Vehicle Information Charging System Monitor • 2. A list of on-board systems and components available for testing are shown on the display. Select test. • Use the UP and DOWN keys until desired test is highlighted. • Press . On-Board Systems EVAP System Test • • The CVN calculation may take several minutes.
PAGE 38
en | 3 8 | User guide | CP9680 AutoScanner® Plus VIN (MOD $09) Vehicle Information 1HGCM56866A018504 Retrieving CVN data. It may take up to 1.5 minutes. Press BACK to exit CVN (MOD $09) Vehicle Information 00 5C 02 52 Retrieving CALID data. It may take up to 1.5 minutes. Press BACK to exit CAL ID (MOD $ 09) Vehicle Information 37805-RAD-A590 -------------- Retrieving IPT data. It may take up to 1.5 minutes. Press BACK to exit IPT (MOD $ 09) 2. Select information to view from the menu.
PAGE 39
CP9680 AutoScanner® Plus | User guide | 39 | en Sensor Monitor Completion Counts O2SCOMPX O2 Bank x Sensor Conditions Encountered O2SCONDX O2 Counts Bank x Monitor Completion Condition EGRCOMP EGR Counts Monitor Conditions Encountered EGRCOND EGR Counts AIR Monitor Completion Condition AIRCOMP Counts (Secondary Air) AIR Monitor Conditions Encountered AIRCOND Counts (Secondary Air) Monitor Completion Condition EVAPCOMP EVAP Counts Monitor Conditions Encountered EVAPCOND EVAP Counts Oil Service Reset Cycle
PAGE 40
en | 4 0 | User guide | CP9680 AutoScanner® Plus battery) or a battery with a different capacity (mAh), the vehicle may require reprogramming to the new battery type in addition to performing the battery reset. Reprogramming is not a function of the tool. Consult the vehicle manual for additional vehicle-specific information. From the Special Tests Menu: 1. Select Battery Reset. • Use the UP and DOWN keys until Battery Reset is highlighted. • Press .
PAGE 41
CP9680 AutoScanner® Plus | User guide | 41 | en Test Results Charging System Monitor DLC KOEO Voltage DLC Cranking Voltage DLC KOER Voltage 12.2 10.4 14.7 DLC KOEO Voltage: 12.2V Please start the engine Press BACK to exit 4. ess ENTER to view the data plot. When the cranking condition is detected, the scan tool will begin collecting DLC voltage readings. • If the engine starts, press . Charging System Monitor Collecting data Press ENTER when the engine has started 5.
PAGE 42
en | 4 2 | User guide | CP9680 AutoScanner® Plus Special Tests Modules Present O2 Monitor Tests Diagnostic Monitor Tests On-Board Systems Vehicle Information Oil Light Reset Charging System Monitor Modules Present Component Locator Acronyms ID Protocol $01 CAN*7e9 $00 CAN*7e8 Press ENTER to continue The types of protocols (communication types) supported by the scan tool are: • ISO 9141-2 protocol is shown as ISO.
PAGE 43
CP9680 AutoScanner® Plus | User guide | 43 | en • 6.2 Verify the control module is not defective. Refer to the service manual to diagnose the control module. Scan Tool Does Not Power Up WARNING Review Safety Messages on page 5 before troubleshooting. If scan tool will not power up, communicate with vehicle control module, pass scan tool self-tests, or functions incorrectly in any other way, do the following: • Check and replace the batteries (if needed). • Clean the DLC pins.
PAGE 44
en | 4 4 | User guide | CP9680 AutoScanner® Plus PID PID Description PID PID Description AECD10_TIME1, TIME 2 AECD11_TIME1, TIME 2 AECD12_TIME1, TIME 2 AECD13_TIME1, TIME 2 AECD14_TIME1, TIME 2 AECD15_TIME1, TIME 2 AECD16_TIME1, TIME 2 AECD17_TIME1, TIME 2 AECD18_TIME1, TIME 2 AECD19_TIME1, TIME 2 AECD2_TIME1, TIME 2 AECD20_TIME1, TIME 2 AECD3_TIME1, TIME 2 AECD4_TIME1, TIME 2 AECD5_TIME1, TIME 2 AECD6_TIME1, TIME 2 AECD7_TIME1, TIME 2 AECD8_TIME1, TIME 2 AECD9_TIME1, TIME 2 ALCOHOL BARO PRS BAT_PWR BP
PAGE 45
CP9680 AutoScanner® Plus | User guide | 45 | en PID PID Description PID FRT_A, B FUEL LEVEL FUEL PRES Fuel Rail Temperature A, B Fuel Level Input Fuel Rail Pressure Fuel System 1 Loop Status, System 2 Loop Status Fuel Type Engine Fuel Rate Fueling Injection Timing Glow Plug Lamp Status Commanded Intake Air Flow A Control, B Control Relative Intake Air Flow A Position, B Position Intake Air Temp Intake Air Temperature Sensor Bank 1 Sensor 1, Bank 2 Sensor 1 Intake Air Temperature Sensor Bank 1 Sensor 2,
PAGE 46
en | 4 6 | User guide | CP9680 AutoScanner® Plus PID PID Description TAC_A_REL, B_ REL TCA_CINP, TCB_ CINP TCA_CINT, TCB_ CINT TCA_COUTT, TCB_COUTT TCA_RPM, TCB_ RPM TCA_TOUTT, TCB_TOUTT TCA_TINT, TCB_ TINT THROT CMD TP G TQ_ACT Relative Throttle A Position, B Position TQ_DD TQ_MAX1, MAX2, MAX3, MAX4, MAX5 TQ_REF TROUB CODE VEH SPEED VGT_A_ACT VGT_A_ACT, B_ ACT Turbocharger Compressor Inlet Pressure Sensor A, Pressure Sensor B Turbocharger A Compressor Inlet Temperature, Turbocharger B Turbocharger A
PAGE 47
CP9680 AutoScanner® Plus | User guide | 47 | en CAM: Camshaft position sensor. Sends a frequency signal to the PCM to synchronize fuel injector and spark plug firing. Catalytic converter: Designed to reduce exhaust emissions. CAN: Controller area network CARB: California air resources board. Governing body for emissions control in California. CKP REF: Crankshaft position reference. CKP: Crankshaft position. See CPS.
PAGE 48
en | 4 8 | User guide | CP9680 AutoScanner® Plus determines optimum spark timing from sensor information — engine speed, throttle position, coolant temperature, engine load, vehicle speed, Park/Neutral switch position, and knock sensor condition. EVAP: Evaporative emissions system FC: Fan control Freeze frame: A block of memory containing DTCs of the vehicle operating conditions for a specific time. FTP: Federal test procedure. Strict test of vehicle’s emissions.
PAGE 49
CP9680 AutoScanner® Plus | User guide | 49 | en voltage changes to 0.4 volts or less when the exhaust gas is lean (high oxygen content). This sensor only operates after it reaches a temperature of approximately 349ºC (660ºF). O2 sensors are usually found both upstream and downstream of the catalytic converter. The PCM uses these sensors to fine tune the air-fuel ratio and to monitor the efficiency of the catalytic converter. See Bank 1, Bank 2, Sensor 1, Sensor 2.
PAGE 50
en | 5 0 | User guide | CP9680 AutoScanner® Plus STS: Service throttle soon TAC: Throttle actuator control TBI: Throttle body injection. A fuel injection system having one or more injectors mounted in a centrally located throttle body, as opposed to positioning the injectors close to an intake valve port. TBI is also called Central Fuel Injection (CFI) in some vehicles. TCC: Torque converter clutch TCM: Transmission control module TCS: Traction control system for PCM and brakes TDC: Top dead center.
PAGE 51
CP9680 AutoScanner® Plus | User guide | 51 | en 9 Limited Warranty THIS WARRANTY IS EXPRESSLY LIMITED TO ORIGINAL RETAIL BUYERS OF BOSCH ELECTRONIC DIAGNOSTIC TOOLS (“UNITS”). BOSCH Automotive Service Solutions LLC Units are warranted against defects in materials and workmanship for one year (12 months) from date of delivery.
PAGE 52
Bosch Automotive Service Solutions Inc. 3000 Apollo Drive Brook Park, OH 44142 USA Telephone 1-800-228-7667 www.actron.