User Guide
Table Of Contents
- 1 Safety Precautions
- 1.1 Read All Instructions
- 2 Important Safety Warnings and Instructions
- 3 Getting Started
- 4 Using the Scan Tool
- 5 Diagnostic Menu
- 5.1 I/M Monitors (Emissions)
- 5.2 Read Codes
- 5.3 Erase Codes
- 5.4 MIL Status
- 5.5 State OBD Check
- 5.6 View Data
- 5.7 Record Data
- 5.8 View Freeze Data
- 5.9 Drive Cycle Monitor
- 5.10 O2 Monitor Tests
- 5.11 Diagnostic Monitor Tests
- 5.12 On-Board Systems
- 5.13 Vehicle Information
- 5.14 Oil Light Reset
- 5.15 Battery Reset
- 5.16 Charging System Monitor
- 5.17 Modules Present
- 6 Troubleshooting
- 7 Appendix A— PID Definitions
- 8 Appendix B—Glossary
- 9 Limited Warranty
en
|
26
|
User guide
| CP9680
AutoScanner® Plus
573102 | REV. B | 03.2016
Bosch Automotive Service Solutions Inc.
PM Filter Mon Particulate matter filter monitor
3. Return to Special Tests Menu.
• Press .
5.2 Read Codes
The Read Codes function allows the scan tool to read
the DTCs from the vehicle’s control modules. DTCs are
used to help determine the cause of a problem or prob-
lems with a vehicle. These codes cause the control
module to illuminate the malfunction indicator lamp
(MIL) when emission-related or driveability fault occurs.
When referring to the engine control module, MIL is also
known as service engine soon or check engine lamp.
Read Codes can be done with the key on engine off
(KOEO) or with the key on engine running (KOER).
From the Diagnostic Codes Menu:
1. Select Read Codes.
• Use the UP and DOWN keys until Read
Codes is highlighted.
• Press .
Diagnostic Codes
Read Codes
Erase Codes
View Freeze Data
Component Locator
Acronyms
Review Data
Print Data
Code Lookup
System Setup
2. If more than one module is supported, a menu is
displayed.
• Use the UP and DOWN keys until the
desired choice is highlighted.
• Press .
Select Module
OBDII/EOBD
Engine
ABS
Airbag
All of the Above
If no DTCs are present, a message stating “System Pass: No
Faults Detected” is displayed. If All of the Above is selected
from the Select Module menu, all of the codes will be
displayed as if all menu items were selected individually.
Read Codes
Press ENTER to continue
No codes found
3. View and write down the DTCs.
• Use the UP and DOWN keys until the
desired choice is highlighted.
This screen indicates where the Read Codes information
is located.
DTC Description
DTC Type
X/Y
Module
DTC#
DTC Number - number of the trouble code found in
vehicle service information.
X of Y - Indication that code x of y is being viewed,
where x is the code being viewed of the total y.
Module - The name of the module (e.g. ABS) or address of
the module (e.g. Mod $28) or both are shown (ABS $28) in
this field. The table below describes modules supported.
Module Description
ECM Engine or powertrain module
TCM Transmission control module
TCCM Transfer case control module
ABS Anti-lock brake system module
HPCM Hybrid powertrain control module
MOD $XX
Module address for the OBDII/EOBD mod-
ule reporting the DTC
SRS Supplemental restraint system module
DTC Description - This area is reserved for the text describ-
ing the trouble code listed in the DTC number field.
DTC Type - This area is reserved for providing additional
information about the DTC. Multiple DTC types may be
possible for a given DTC number. Not all vehicles sup-
port DTC types. This table describes possible DTC types.
DTC Type Description
History
Intermittent codes placed in the vehicle’s
memory when the trouble originally oc-
curred, and will remain there even if the
trouble has been corrected. If no trouble
after 50 engine warm-up cycles, the DTC
will be erased.