http://www.advancedactuators.com PREFACE Thank you for purchasing the Actuator Systems NextBolt fingerprint deadbolt. Please read the documentation carefully before installation & use. The manual details all installation procedures and operation steps. Manufacturer and/or Distributors of the Actuator Systems NextBolt will not be responsible for any damages caused by incorrect installation or mishandling of the lock. Any such damages will void manufacturer’s warranty.
http://www.advancedactuators.com Table of Contents Preface………………………………………………………………1 Installation Manual 1. Parts ........................................................................................ 3 2. Required Tools........................................................................ 5 3. Pre-installation ........................................................................ 5 3.1 Mark and bore holes on the door .................................. 5 3.2 Deadbolt Latch Selection ..................
http://www.advancedactuators.com 1. Parts Please familiarize yourself with all the parts in the packaging box of the Actuator Systems NextBolt. If any part is missing or damaged, contact our service center or your local dealer. Outdoor Unit Indoor Unit Strike Lining Box Indoor and Outdoor Rubber Gaskets Strike Plate Keys 3 NextBolt User Manual For support contact us a 1-800-408-7101 ext.
http://www.advancedactuators.com Deadbolt Latch 2 ¾‖ backset (70mm) Screws (2 x 18 mm & 1 x 29mm) Deadbolt Latch 2 3/8‖ backset (60mm) Wooden & Metal Screws (1) Fixing Plate 4 NextBolt User Manual For support contact us a 1-800-408-7101 ext.
http://www.advancedactuators.com 2. Required Tools – With the EZ Mount Kit Installation is quick and easy. If your door has an existing deadbolt you only need the following tools. ① Philips & flat head screw drivers 3. Pre-installation 3.1 Mark and bore holes on the door 3.11 Mark holes on door For doors with existing deadbolt lock with 2 1/8” diameter hole: 1) Remove existing cylindrical deadbolt . 5 NextBolt User Manual For support contact us a 1-800-408-7101 ext.
http://www.advancedactuators.com 2) Please be sure to use the included clear installation template when installing the Actuator Systems NextBolt on a door with an existing deadbolt. 3) Rest the installation template on the front of the door, on top of the existing 2 1/8‖ hole, making sure that it is aligned properly for the door’s existing 2 3/8‖ or 2 ¾‖ backset. 6 NextBolt User Manual For support contact us a 1-800-408-7101 ext.
http://www.advancedactuators.com For doors that do not have a cylindrical deadbolt lock or a hole for the cylindrical deadbolt lock: A. Start approximately 46‖ from floor. Select the appropriate installation template according to the length of the backset. Fold and apply the template to the edge of the door bevel. Mark the center point of the cylinder hole on the door face, and then mark the center point of the deadbolt hole on door edge, as indicated on the template. B.
http://www.advancedactuators.com 3.12 Bore holes A. Bore a 2 1/8‖ diameter hole in the center of door face for chassis. (It is recommended to bore this hole from both sides of the door to avoid splintering.) B. Bore a 1‖ diameter hole in the center of door edge for deadbolt. 3.2 Deadbolt Latch Selection There are two deadbolt latches in each box, one with a 2 3/8‖ (60mm) backset and the other with a 2 ¾‖ (70mm) backset. Make sure which length you will need and select the right one before installation.
http://www.advancedactuators.com 4. Installation 4.1 Installation of Deadbolt A. Insert the deadbolt latch into the hole in the edge of the door (follow the UP sign), keeping it parallel to the face of the door. Mark the outline of the face plate and remove the deadbolt. B. Then chisel 1/8‖ deep rectangular shape, per your marking (or until the faceplate is flush with the door edge). C. Insert the deadbolt latch; make sure the deadbolt UP sign is facing upwards. Then fasten the screws.
http://www.advancedactuators.com 4.2 Installing Strike and Strike Lining Box (on the door jamb) A. (1) Close the door until the deadbolt touches the door jamb along the face plate to mark the horizontal center lines. (2) Measure one half of the door thickness from one side of the door jamb, and then mark the vertical center lines. (3) Extend the vertical center line and the horizontal line to mark the drill center point for the strike. B.
http://www.advancedactuators.com 4.3 Sizing Tail Piece (to the right length) The Actuator Systems NextBolt is designed to fit door thicknesses of 1 3/8‖ to 2‖. Four pre-sized tailpieces are included with the Actuator Systems NextBolt for 1 3/8‖, 1 ½‖, 1 ¾‖ and 2‖ thick doors. Your door thickness and length of the tailpiece being used must match exactly. EX: If your door is 1 ¾‖ thick, then you must use the 1 ¾‖ long tailpiece. The Actuator Systems NextBolt comes with the 1 ¾‖ tailpiece preinstalled.
http://www.advancedactuators.com IF YOUR DOOR THICKNESS DOES NOT EXACTLY MATCH ANY OF THE PRE-CUT TAILPIECES LENGTHS, THEN YOU MUST TRIM THE PRE-INSTALLED TAIL PIECE TO MATCH YOUR EXACT DOOR THICKNESS. If you need to trim the tailpiece, be sure to measure the exact thickness of your door, mark the tailpiece (with a marker) where it needs to be cut and trim the tail piece accordingly per the exact thickness of your door, with a hacksaw or metal cutters.
http://www.advancedactuators.com 4.4 Installation of the Outdoor Unit 1) Attach the rubber gasket to the back of the outdoor unit. 2) Make sure the deadbolt is engaged. 13 NextBolt User Manual For support contact us a 1-800-408-7101 ext.
http://www.advancedactuators.com 3) Make sure the tail piece is vertical. 4) Insert tail piece through the cross slot of the latch. 14 NextBolt User Manual For support contact us a 1-800-408-7101 ext.
http://www.advancedactuators.com 5) Insert the connector and wire through the cylinder hole below the deadbolt latch. 6) On the INSIDE side of the door screw the fixing plate to the outside door lock using the two 90mm screws. You can break off the screws to the needed length depending on your required thickness. Insure these have a snug fit. 15 NextBolt User Manual For support contact us a 1-800-408-7101 ext.
http://www.advancedactuators.com 4.5 Installation of the Indoor Unit The outdoor unit should now be firmly fastened to the outside of the door. This will make it much easier and simpler to attach the inside portion of the lock. 1) Select the proper door opening orientation on the back plate of the Indoor Unit. If the door is left handed, please push the orientation selector switch to ―L‖ position; if it’s right handed, switch the selector to ―R‖ position.
http://www.advancedactuators.com 2) Plug wire set into circuit board, making sure all prongs are firmly seated. Make sure the black dots on the cable and connector align. 3) Turn the manual turn knob to the vertical position, facing downward. 17 NextBolt User Manual For support contact us a 1-800-408-7101 ext.
http://www.advancedactuators.com 4) Insert the tail piece into the vertical retaining slot of the indoor unit. 5) Gently finish joining the outdoor and indoor units together. . 18 NextBolt User Manual For support contact us a 1-800-408-7101 ext.
http://www.advancedactuators.com 6) Fasten the two shorter (15mm) screws through the fixing plate on the upper section of the inside unit. 19 NextBolt User Manual For support contact us a 1-800-408-7101 ext.
http://www.advancedactuators.com 7) Fasten the two long screws through the bottom fixing post holes on the inside unit. 8) Move the manual turn knob back and forth to ensure that deadbolt opens and closes mechanically. 20 NextBolt User Manual For support contact us a 1-800-408-7101 ext.
http://www.advancedactuators.com 9) Insert 4 high-quality AA batteries 21 NextBolt User Manual For support contact us a 1-800-408-7101 ext.
http://www.advancedactuators.com 10) Press the electronic open/close button to ensure that the deadbolt opens and closes electronically. 4.6 Final inspection/adjustment prior to enrollment Note: After installation and prior to using the unit, make sure you read and follow the steps below: ① Turn the inside knob to the horizontal position; next turn it to the vertical position (locked position). It should turn freely.
http://www.advancedactuators.com CLOSING THE SLIDING COVER. 5. Trouble Shooting PROBLEMS Indoor turn knob does not turn or turns very sluggishly POSSIBLE REASONS 1. Incorrect installation 2. Incorrect tailpiece length SOLUTIONS 1. Make sure the tail piece was inserted vertically through the cross slot of the deadbolt and slot of the indoor unit while the turn knob was vertical (facing down). 2. Measure the door thickness and swap or trim the tail piece per section 4.
http://www.advancedactuators.com Indoor turn knob turns but nothing happens. 1. The tail piece 1. Remove and reinstall the did not go outdoor unit. Then insert the through the cross tail piece through the cross slot of the slot of the deadbolt and slot deadbolt; of the indoor unit while the turn knob is in vertical position (facing down). 2.
http://www.advancedactuators.com When the sliding 1. Improper cover is fully lifted positioning of and immediately the strike and put down to engage strike lining box. the deadbolt, but It may be the deadbolt does deflecting the not fully engage, or deadbolt. four alert beeps are heard. When the sliding 1. Batteries not cover is lifted up inserted during daily use, correctly; nothing happens (fingerprint scanner does not blink) 2.
http://www.advancedactuators.com With no fingerprints enrolled in the Actuator Systems NextBolt, the deadbolt will engage/disengage when the sliding cover is fully opened and immediately closed. Definitions of Indication Beeps: Single, Short Beep – Indicates that any operations sequence has begun OR that the door has been successfully locked or unlocked OR that the sliding cover has been left open for more than ten seconds.
http://www.advancedactuators.com Verifying Fingerprints: Process of authentication by scanning enrolled fingerprints to: A) Unlock the door B) Authenticate Administrators enrolled fingerprints to program the Actuator Systems NextBolt.
http://www.advancedactuators.com Always wait until the fingerprint scanner turns on to place your finger on the scanning window. This is true for both fingerprint enrollment AND verification. When trying to enroll or verify fingerprints in direct sunlight, be sure to shade the sensor with your shadow, so sunlight will not reflect off of the mirror in the sensor.
http://www.advancedactuators.com The first two fingerprint users enrolled will automatically be programmed as ADMINISTRATORS (Users 1 and 2). ADMINISTRATORS can apply all programming functions as well as verify their fingerprints to unlock the door. The 3rd thru 99th fingerprint users enrolled (Users 3 thru 99) are automatically programmed at the USER level. USER level fingerprints can only be used to unlock the door, not to program the lock.
http://www.advancedactuators.com Fully open the sliding cover located on the outdoor unit immediately Sensor will flicker for less than one second A single short beep will be heard and the fingerprint sensor will power on After the fingerprint sensor powers on , rest your pointer finger on the sensor window during the first of three scans Keep your pointer finger on the scanning window thru all three scans.
http://www.advancedactuators.com Close the sliding cover (USER 2 through USER 99): Section II - Enrolling Fingerprint Users 2 thru 99: Sliding cover must be closed before any programming sequence can begin. As noted in the Helpful Hints section, the third thru ninety-ninth fingerprint users enrolled (Users 3 thru 99) are automatically programmed at the USER level. USER level fingerprints can only be used to unlock the door, not to program the lock.
http://www.advancedactuators.com Remove the battery cover from the indoor unit Press the ―ADD‖ button located on the indoor unit Single beep will be heard 32 NextBolt User Manual For support contact us a 1-800-408-7101 ext.
http://www.advancedactuators.
http://www.advancedactuators.com A single short beep will be heard and the fingerprint sensor will power on Rest the new user’s pointer finger on the sensor window during the first of three scans Keep your pointer finger on the scanning window until you hear a single long beep or four beeps. After the scanning is completed you will hear one of the following: o Single, long beep indicating that the operation was successful OR o Four beeps indicating that your fingerprint was not successfully enrolled.
http://www.advancedactuators.com Section III – Deleting Individual Fingerprint Users: Sliding cover must be closed before any programming sequence can begin. The Individual Fingerprint User Deletion programming function deletes the individual user you select from your enrolled users.
http://www.advancedactuators.com Fully open the sliding cover located on the outdoor unit immediately Sensor will flicker for less than one second A single short beep will be heard and the fingerprint sensor will power on Rest an Administrator’s fingerprint on the scanning window When the LED light goes out enter the keypress sequence. (The chart is in Appendix A of this manual). o If you hear four beeps this indicates that the Administrator was not recognized.
http://www.advancedactuators.com id sequence and wait for the long beep for each user you wish to remove. Close the sliding cover to end the deletion procedure. Close the sliding cover Repeat steps from the beginning of Section III to delete the next most recently enrolled fingerprint user. Section IV – Deleting ALL Fingerprint Users: Sliding cover must be closed before any programming sequence can begin.
http://www.advancedactuators.com Please use the following steps to delete ALL fingerprint users: 1. Press and hold the DEL button. 2. While holding down the DEL button add the other two buttons (ADD & OPEN/CLOSE). Now all three buttons on the lock will be held down. 3. When one long beep is heard, pull the outside cover up and place the Admin finger on the sensor for verification when the sensor light turns on. 4. Once one long beep is heard, the lock is reset successfully.
http://www.advancedactuators.com Section V – Unlocking the Actuator Systems NextBolt from outside: In case of emergency, override keys can be used to disengage the deadbolt. Please use the following steps to unlock the Actuator Systems NextBolt from outside, with your enrolled fingerprint: Fully lift the sliding cover located on the outdoor unit. 39 NextBolt User Manual For support contact us a 1-800-408-7101 ext.
http://www.advancedactuators.com A single short beep will be heard and the fingerprint sensor will power on After the fingerprint sensor powers on, rest any enrolled fingerprint on the sensor window to verify. If fingerprint verification is successful, the deadbolt will disengage and a single, short beep will be heard; If verification of enrolled fingerprint was not successful, then 4 short beeps will be heard.
http://www.advancedactuators.com Close the sliding cover Section VI – Locking the Actuator Systems NextBolt from Outside: In case of emergency, override keys can be used to engage the deadbolt. Please use the following steps to lock the Actuator Systems NextBolt from outside (when leaving): 41 NextBolt User Manual For support contact us a 1-800-408-7101 ext.
http://www.advancedactuators.com Make sure your door is closed Open and immediately close the sliding cover Deadbolt will engage and a single, short beep will be heard Section VII – Locking and Unlocking the Actuator Systems NextBolt from Inside: In case of emergency, manual turn knob can be used to disengage the deadbolt. Please use the following steps to lock and unlock the Actuator Systems NextBolt from inside: 42 NextBolt User Manual For support contact us a 1-800-408-7101 ext.
http://www.advancedactuators.com Press the ‖OPEN/CLOSE‖ button (located between the ADD and DEL buttons) Deadbolt will engage/disengage and single, short beep will be heard. Support: Contact the Actuator Systems NextBolt dealer that you purchased the lock from OR Contact us at: support@advancedactuators.com for additional support. 43 NextBolt User Manual For support contact us a 1-800-408-7101 ext.
http://www.advancedactuators.
http://www.advancedactuators.
http://www.advancedactuators.
http://www.advancedactuators.com 88 89 90 91 92 93 94 95 96 97 98 99 ADD/DEL/ADD/ADD/DEL/DEL/DEL ADD/DEL/ADD/ADD/DEL/DEL/ADD ADD/DEL/ADD/ADD/DEL/ADD/DEL ADD/DEL/ADD/ADD/DEL/ADD/ADD ADD/DEL/ADD/ADD/ADD/DEL/DEL ADD/DEL/ADD/ADD/ADD/DEL/ADD ADD/DEL/ADD/ADD/ADD/ADD/DEL ADD/DEL/ADD/ADD/ADD/ADD/ADD ADD/ADD/DEL/DEL/DEL/DEL/DEL ADD/ADD/DEL/DEL/DEL/DEL/ADD ADD/ADD/DEL/DEL/DEL/ADD/DEL ADD/ADD/DEL/DEL/DEL/ADD/ADD 47 NextBolt User Manual For support contact us a 1-800-408-7101 ext.
http://www.advancedactuators.com USER ENROLLMENT TABLE Number Name Finger Used (L/R) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 48 NextBolt User Manual For support contact us a 1-800-408-7101 ext.
http://www.advancedactuators.com 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 49 NextBolt User Manual For support contact us a 1-800-408-7101 ext.
http://www.advancedactuators.com 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 50 NextBolt User Manual For support contact us a 1-800-408-7101 ext.
http://www.advancedactuators.com 91 92 93 94 95 96 97 98 99 51 NextBolt User Manual For support contact us a 1-800-408-7101 ext.
http://www.advancedactuators.com We would like to personally thank you for your purchase of our exciting NextBolt Series biometric deadbolt lock from Actuator Systems. We hope you enjoy using it as much as we enjoy developing this technology for you. For more helpful information about your NextBolt please visit www.advancedactuators.com/support.php or our knowledgebase at http://www.advancedactuators.com/kb/ For all Tech Support Questions: Call: 407-567-7130 Ext 102 or Email: support@advancedactuators.
