Instruction Manual Professional Weather Center model 01010 CONTENTS Unpacking Instructions............ 2 Package Contents................... 2 Product Registration................ 2 Features & Benefits: 5-in-1........ 3 Features: Display Unit............. 4 Back of Display Unit................ 6 Setup..................................... 7 5-in-1 Sensor Setup................. 7 Display Unit Setup.................. 8 Set the Time & Date................ 9 Measurement Units................
Congratulations on your new AcuRite product. To ensure the best possible product performance, please read this manual in its entirety and retain it for future reference. Unpacking Instructions Remove the protective film that is applied to the LCD screen prior to using this product. Locate the tab and peel off to remove. Package Contents 1. Display unit with tabletop stand 2. 5-in-1 sensor 3. Sensor mounting bracket 4. Mounting hardware 5. Snap-in debris filter for rain collector 6.
Features & Benefits 7 1 2 9 11 3 4 5 8 6 10 5-IN-1 SENSOR 1. R ainfall Collector Funnel 5. T emperature & Humidity Sensors (internal) 2. Solar Cell Panel Converts sunlight into power to run internal aspirating fan. 6. Mounting Bracket 7. W ind Speed Anemometer Internal Aspirating Fan (not shown) 8. Wind Direction Vane Draws ambient air into sensor to reduce solar radiation heating, resulting in more accurate temperature measurement. 9. Mounting Bracket 10.
Features & Benefits Display Unit 36 35 34 1 33 32 2 3 31 30 4 29 5 28 6 7 27 26 8 25 24 9 10 37 11 23 21 12 19 13 14 15 16 4 17 18 22 20
1. Peak Wind Speed 19. Record Lows Highest speed from past 60 minutes. Shown for current category selected on the display (#15). 2. Wind Speed Alarm On Indicator 20. Clear Button 3. Average Wind Speed Deletes record low (#19) shown. of all speeds from past 2 minutes. 21. Record Highs 4. Pressure History Graph Shown for current category selected on the display (#15). Current pressure on right with trend (Rising, Steady or Falling). 22. Clear Button 5.
Back of Display Unit 1 2 3 4 5 BACK OF DISPLAY UNIT 1. A-B-C Switch 4. Clear All ID code that must match 5-in-1 sensor’s A-B-C switch to ensure units synchronize. Clears all data recorded without having to reset time and date. 2. Clear Today Clears data recorded since 12:00am. 3. Reset Full reset to factory defaults. 6 5. Battery Compartment 6. Battery Compartment Cover (Not shown.
SETUP 5-in-1 Sensor Setup 1 Set the A-B-C Switch Locate the A-B-C switch inside the battery compartment. Set the A-B-C switch to A, B or C. You must select the same letter choices for both the sensor and the display unit in order for the units to synchronize. 2 Install or Replace Batteries Batteries MUST be installed for this product to operate. AcuRite recommends high quality alkaline or lithium batteries for the best product performance. Heavy duty or rechargeable batteries are not recommended.
Display Unit Setup 2 Install or Replace Batteries 1 Set the A-B-C Switch The A-B-C switch is located inside the battery compartment. It can be set to A, B or C. However, you must select the same letter choices for both the sensor and the display unit in order for the units to synchronize. Insert 3 x AA alkaline batteries into the battery compartment, as shown. Follow the polarity (+/-) diagram in the battery compartment.
Set the Time & Date The clock and calendar are utilized to time stamp history records and other data, so it is important to set the time and date soon after you power on the display unit. Set the Time 1. Press the “▲” or “▼” buttons until “SET CLOCK?” is displayed on the Selectable Category part of the display unit. 2. Press the “SET” button to set the clock. 3. Press the “▲” or “▼” to adjust the hour. Note the “AM” and “PM” indicators. 4. Press the “SET” button to confirm hour selection. 5.
Select Measurement Units To select between standard units (mph, ºF, etc.) or metric units (kph, ºC, etc.): 1. Press the “▲” or “▼” buttons until “SET UNITS?” is displayed on the Selectable Category part of the display unit. 2. Press the “SET” button to set the unit preference. 3. Press the “▲” or “▼” to select “STAND” for standard or “METRIC” for metric units. 4. Press the “SET” button to confirm your selection. 5. Next, you will see “WIND MPH”.
Placement for Maximum Accuracy AcuRite sensors are sensitive to surrounding environmental conditions. Proper placement of both the display unit and the sensor are critical to the accuracy and performance of this product. Display Unit Placement Place the display unit in a dry area free of dirt and dust. To ensure accurate temperature measurement, place out of direct sunlight and away from heat sources or vents. Display unit stands upright for tabletop use or is wall-mountable.
5-in-1 Sensor Installation Guidelines INSTALLATION HEIGHT Mount the sensor at least 5 feet (1.5 meters) off the ground (higher is better for wind measurement) in an open area. Secure to fence post, 2”x 4” wood, 3/4” pole, etc. (not included) LEVEL INSTALLATION Use the bubble level (included on top of sensor) to ensure level installation for accurate wind measurement. SOLAR CELL INSTALLATION Install the sensor with the solar cell facing SOUTH.
OPERATION Using the Professional Weather Center Learning Mode Self-Calibrating Forecasting use a unique algorithm to analyze changes in pressure over a time period (called Learning Mode) to determine your altitude. After 14 days, the Learning Mode icon disappears from the display screen. At this point, the self-calibrated pressure is tuned in to your location and the unit is ready for superior weather prediction.
Programmable Weather Alarms Each Selectable Weather Category features an alarm option. When an alarm sounds, the display unit emits an audible beep and flashes the affected category, its alarm settings, and any other relevant data. Some alarms can be customized to alert you when your programmed value is reached.
Set a Weather Alarm 1. Choose the weather category for which you wish to set an alarm by pressing the “▲” or “▼” buttons until the category is displayed on the Selectable Category part of the display unit. 2. To program a value (only applies to alarms that require a value), press AND HOLD the “ ” button until the “SET” indicator appears in the area of the display labeled “ALARM” (left of the selected weather category) and the alarm setting flashes. 3.
Troubleshooting Problem No outdoor sensor reception no bars Possible Solution •R elocate the display unit and/or the 5-in-1 sensor. The units must be within 330 ft (100 m) of each other. •M ake sure both units are placed at least 3 feet (.9 m) away from electronics that may interfere with the wireless communication (such as TVs, microwaves, computers, etc). •U se standard alkaline batteries (or lithium batteries in sensor when temperature is below -4ºF/-20ºC).
Troubleshooting Problem Inaccurate temperature or humidity Possible Solution •M ake sure both the display unit and sensor are placed away from heat sources or vents (see p.11). •M ake sure both units are positioned away from moisture sources (see p.11). •M ake sure sensor is mounted at least 5 ft off the ground. • Calibrate indoor and outdoor temperature and humidity (see p.18). No rainfall • Verify the rain gauge stabilizer (plastic tab) has been removed from the bottom of the sensor (see p.7).
Care & Maintenance Display Unit Care Clean with a soft, damp cloth. Do not use caustic cleaners or abrasives. Keep away from dust, dirt and moisture. Clean ventilation ports regularly with a gentle puff of air. 5-in-1 Sensor Care Clean the Sensor Clean with a soft damp cloth. Do not use caustic cleaners or abrasives that will mar the polished surfaces of the rain collection funnel or the solar cell. Scratches will result in decreased performance and reliability.
3. Press the ”▲“ and ”▼“ buttons to calibrate the data value higher or lower from the actual reading. 4. Press the “SET” button to confirm the calibration a djustment. Note: The “CAL” icon remains i lluminated next to calibrated values. Calibrate the Rain Gauge The rain gauge on the 5-in-1 sensor can be calibrated to improve accuracy. Items Needed: 5-in-1 sensor, display unit, plastic cup, pin, screw driver 1. First, ensure 5-in-1 sensor is perfectly level using built-in bubble level. 2.
Specifications TEMPERATURE RANGE Outdoor: -40ºF to 158ºF; -40ºC to 70ºC Indoor: 32ºF to 122ºF; 0ºC to 50ºC HUMIDITY RANGE Outdoor: 1% to 99% Indoor: 16% to 98% WIND SPEED 0 to 99 mph; 0 to 159 kph WIND DIRECTION INDICATORS 16 points RAINFALL 0 to 99.99 in; 0 to 99.
Customer Support AcuRite customer support is committed to providing you with best-inclass service. For assistance, please have the model number of this product available and contact us in any of the following ways: (877) 221-1252 info@chaney-inst.com 24/7 support at www.AcuRite.
Weather Stations Temperature & Humidity Weather Alert Radio Kitchen Thermometers & Timers Clocks It’s More than Accurate, it’s AcuRite offers an extensive assortment of precision instruments, designed to provide you with information you can depend on to Plan your day with confidence™. www.AcuRite.com Printed in China 01010 INST 031414 ©Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark of the Chaney Instrument Co., Lake Geneva, WI 53147.
