User's Manual

ManualsBrandsAcu-Rite ManualsWeather RadioAcu-Rite 973

Thank You! We appreciate you for purchasing the new generation radio-controlled

wireless weather station and atomic clock. This instrument is designed and engineered

with state-of-the-art technology and components. It will provide these accurate and

reliable measurements: date, time, barometric pressure, and indoor/outdoor tempera-

tures and humidity levels. A weather forecast component rounds out the features of this

versatile weather clock.

1 CHECK PACKAGE CONTENTS

(1) Main Unit – 9.25” x 6” x 1”*

(1) Thermo. Hygro. remote sensor – 2.5” x 3.75” x 1”*

(1) 10’* wired low temperature adaptor

(2) 1” (2.5cm) screws with plastic anchors

(1) Instruction manual

00973 INST0511-06

Deluxe Wireless Weather Station

& Atomic Clock

Main Unit

Instruction Manual

MODEL # 00973

CHANNEL

MIN/MAX

PRESSURE

ALARM

C/F

0-1-2-3-6-12

-.24

-.18

-.12

-.06

+.06

+.12

+.18

+.24

- 8

- 6

- 4

- 2

inHg/Hr Hr/hPa

MOON

REMOTE

INDOOR OUTDOOR

PRESSURE

FORECAST

MAIN UNIT

(zone)

2 READ

Please read this entire manual carefully before you set up the instrument and begin to

use it. In this way you can become familiar with the features of the weather station &

clock to get the most benefit from it.

9 PRODUCT SPECIFICATIONS MODEL#00593W

MEASUREMENT RANGE:

Indoor main unit : 0º C to + 50º C (+32º F to +122º F)

Outdoor/Indoor humidity : 20% - 99% RH

Wireless sensor : -20º C to +70º C (-4º F to +158º F)

with low-temp adaptor : -30º C to +70º C (-22ºF to +158º F)

Barometer : 900 to 1050 mb/hPa

Channel : maximum of three wireless sensors

Transmission : up to 30M (100 ft.) open area, RF434 MHz

Resolution : 0.1º for temperature, 1% for humidity, 1 hPa mb for

pressure

Clock : WWVB radio-controlled, quartz back-up

Batteries : AA x 2 alkaline for main unit; AA x 2 alkaline for

wireless sensor

* dimensions approximate

Wireless Sensor

with low

temperature

adaptor

THERMO HYGRO

Do not return product to retail store. For Technical Assistance and

product return information, please call Customer Care:

877-221-1252

HOURS: Monday through Friday from 8:00 a.m. to 4:45 pm CST.

Summary of content (5 pages)

PAGE 1
00973 INST0511-06 9 PRODUCT SPECIFICATIONS MEASUREMENT RANGE: Indoor main unit Outdoor/Indoor humidity Wireless sensor with low-temp adaptor Barometer Channel Transmission Resolution : : : : : : : : Clock Batteries : : Instruction Manual MODEL#00593W 0º C to + 50º C (+32º F to +122º F) 20% - 99% RH -20º C to +70º C (-4º F to +158º F) -30º C to +70º C (-22ºF to +158º F) 900 to 1050 mb/hPa maximum of three wireless sensors up to 30M (100 ft.) open area, RF434 MHz 0.
PAGE 2
3 INSTALL BATTERIES SNOOZE Main Unit: Always install batteries into the main unit first. On the back of the unit, remove the battery compartment cover. Insert 2 AA alkaline (or lithium – See NOTES below) batteries. Replace the cover. Wireless Sensor: After batteries have been put into the main unit, remove the 4 screws to remove the back cover of the wireless sensor. Insert 2 AA alkaline (or lithium) batteries. Press the “TX” button and replace the back cover and the 4 screws on the sensor.
PAGE 3
Using the included LOW TEMPERATURE ADAPTOR 5 PREVIEW THE DISPLAY The wireless sensor will operate normally down to -4 ºF. Below -4 ºF, the electronics may operate erratically or become non-functional until the temperature raises again. In case temperatures fall below -4ºF, bring the wireless sensor indoors and use the included low temperature adaptor by running the wire out through a soft seal opening such as a window or door.
PAGE 4
MAIN UNIT WIRELESS SENSOR Operation buttons are located on the front and back of the main unit 6 UNDERSTAND WHAT THE BUTTONS DO.
PAGE 5
Adjust the barometric pressure to reflect your current conditions: NOTE: Please see http://weather.unisys.com/surface/sfc_con_pres.html to help set and adjust the barometric pressure. 1) Hold “PRESSURE” button for 3 seconds 2) Press “P+” , and/or “P-” to adjust the air pressure according to the current pressure. 3) Press the “PRESSURE” button to confirm the setting Moon Phase: The moon phase will automatically display based on the calender date.