User's Manual
www.acuitybrands.com
www.acuitybrands.com
USER MANUAL
ATG2
This product is a battery powered Bluetooth® Low Energy beacon. It works with Acuity Brands’ Atrius™ Assets – Asset
tracking and management software service. The product communicates its position to Atrius Assets.
This product does not have any end user interface. All of the BLE beacon position information are gathered and processed in the
cloud.
ATG2RegulatoryWarningSheet
Warning: Changes or modifications to this device not expressly approved by Acuity Brands
Lighting, Inc. could void the user’s authority to operate the equipment.
“NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.”
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference and (2) this device must accept any interference received, including interference that may cause
undesired operation.
RF Exposure Warning!
This equipment complies with FCC and Industry Canada RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This device contains transmitters and receivers which emit Radio Frequency (RF) energy. The device is designed to
comply with the limits for exposure to RF energy set by the Federal Communications Commission (FCC) of the United States,
Industry Canada (IC) of Canada, and the regulating entities of other countries. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.”
Cet équipement est conforme aux limites d'exposition aux radiations FCC et Industrie Canada RSS-102 établies pour un
environnement non contrôlé. Cet appareil contient des émetteurs et des récepteurs qui émettent de l'énergie de radiofréquence
(RF). L'appareil est conçu pour respecter les limites d'exposition à l'énergie RF fixées par la Federal Communications Commission
(FCC) des États-Unis, Industrie Canada (IC) du Canada et les organismes de réglementation d'autres pays. Cet émetteur ne doit
pas être situé à proximité ou fonctionner en conjonction avec une autre antenne ou un autre émetteur. »
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a
type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its gain should be so chosen that
the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour
l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à
l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à
l'établissement d'une communication satisfaisante.
This radio transmitter (IC: 6715C-ATG2) has been approved by Industry Canada to operate with the antenna types listed below with
the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this
list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.