2000 Integra Hatchback Online Reference Owner's Manual Use these links (and links throughout this manual) to navigate through this reference. For a printed owner's manual, click on authorized manuals or go to www.helminc.com. Contents Owner's Identification Form Introduction ........................................................................................................................................ i A Few Words About Safety.......................................................................
Main Menu Owner's Identification OWNER This Owner's Manual should be considered a permanent part of the car, and should remain with the car when it is sold. ADDRESS STREET CITY STATE/PROVINCE V. I. N. ZIP CODE / POSTAL CODE DELIVERY DATE (Date sold to original retail purchaser) DEALER NAME ADDRESS DEALER NO.
Main Menu Introduction Congratulations ! Your selection of a 2000 Acura Integra was a wise investment. It will give you years of driving pleasure. One of the best ways to enhance the enjoyment of your new Acura is to read this manual. In it, you will learn how to operate its driving controls and convenience items. Afterwards, keep this owner's manual in your car so you can refer to it at any time. Several warranties protect your new Acura.
０３／０７／２６ １９：００：４０ ３１ＳＤＰ６１０ ０００３ Main Menu A A Few Few Words Words About About Safety Safety Your Your safety, safety, and the safety of others, is is very important. important. And And operating this car safely is anisimportant vehicle safely an important responsibility. responsibility.
Main Menu Your Car at a Glance DOOR LOCK SWITCHES/ HATCH LOCK SWITCH (P. 75) MIRROR CONTROLS (P. 86) DIGITAL CLOCK (P. 88) INDICATOR LIGHTS (P. 53) GAUGES (P. 58) HEATING/COOLING CONTROLS (P. 94) POWER WINDOW SWITCHES (P. 84) AUDIO SYSTEM (P. 102) FUEL FILL DOOR RELEASE (P. 124) SHIFT LEVER (P. 138, 140) HOOD RELEASE HANDLE (P. 125) PARKING BRAKE (P.
Main Menu Your Car at a Glance CRUISE CONTROL (P. 67) INSTRUMENT PANEL BRIGHTNESS (P. 63) MOONROOF (P. 85) HAZARD WARNING LIGHTS (P. 65) REAR WINDOW DEFOGGER (P. 65) HORN BUTTONS HEADLIGHTS/TURN SIGNALS (P. 62/63) TILT ADJUSTMENT (P. 66) WINDSHIELD WIPERS/WASHERS (P.
Main Menu 4
Main Menu Driver and Passenger Safety This section gives you important information about how to protect yourself and your passengers. It shows you how to use seat belts properly. It explains your Supplemental Restraint System. And it tells you how to properly restrain infants and children in your car. Important Safety Precautions.......... 6 Your Car's Safety Features.............. 7 Seat Belts........................................ 8 Airbags...........................................
Main Menu Table of Contents Important Safety Precautions You'll find many safety recommendations throughout this section, and throughout this manual. The recommendations on this page are the ones we consider to be the most important. Always Wear Your Seat Belt A seat belt is your best protection in all types of collisions. Airbags supplement seat belts, but airbags are designed to inflate only in a moderate to severe frontal collision.
Main Menu Table of Contents Your Car's Safety Features Your car is equipped with many features that work together to protect you and your passengers during a crash. Some safety features do not require any action on your part. These include a strong steel framework that forms a safety cage around the passenger compartment; front and rear crush zones that are designed to crumple and absorb energy during a crash; and a collapsible steering column.
Main Menu Table of Contents Your Car's Safety Features ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Seat Belts For your safety, and the safety of your passengers, your car is equipped with seat belts in all seating positions. Your seat belt system also includes a light on the instrument panel to remind you and your passengers to fasten your seat belts. Why Wear Seat Belts Seat belts are the single most effective safety device for adults and larger children.
Main Menu Table of Contents Your Car's Safety Features Airbags The most important things you need to know about your airbags are: Airbags do not replace seat belts. The seat belts are the occupants' primary protection in all types of collisions. The airbags supplement the seat belts by providing extra protection for the head and chest of each front seat occupant in a moderate to severe frontal collision.
Main Menu Table of Contents Your Car's Safety Features Seats & Seat-Backs Your car's seats are designed to keep you in a comfortable, upright position so you can take full advantage of the protection offered by seat belts and the energy absorbing materials in the seats. How you adjust your seats and seatbacks can also affect your safety.
Main Menu Table of Contents Your Car's Safety Features Pre-Drive Safety Checklist To make sure you and your passengers get the maximum protection from your car's safety features, check the following each time before you drive away: All adults, and children who have outgrown child safety seats, are wearing their seat belts and wearing them properly (see page 16). Any infant or small child is properly restrained in a child seat in the back seat (see page 21).
Main Menu Table of Contents Protecting Adults Introduction The following pages provide instructions on how to properly protect the driver and other adult occupants. These instructions also apply to children who have outgrown child seats and are large enough to wear lap/shoulder belts. (See page 37 for important additional guidelines on how to properly protect larger children.) 1. Close and Lock the Doors After everyone has entered the car, be sure the doors and the hatch are closed and locked.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ Protecting Adults 2. Adjust the Front Seats Any driver who sits too close to the steering wheel is at risk of being seriously injured or killed by striking the steering wheel, or from being struck by an inflating airbag during a crash.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ Protecting Adults 3. Adjust the Seat-Backs Adjust the driver's seat-back to a comfortable, upright position, leaving ample space between your chest and the airbag cover in the center of the steering wheel. If you sit too close to the steering wheel, you could be injured if the airbag inflates. Driver and Passenger Safety A front passenger should also adjust the seat-back to an upright position, but as far from the dashboard as possible.
Main Menu Table of Contents０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Protecting Adults 4. Adjust the Head Restraints Improperly positioning head restraints reduces their effectiveness and you can be seriously injured in a crash. Properly adjusted head restraints will help protect occupants from whiplash and other crash injuries. See page 82 for how to adjust the head restraints. Make sure head restraints are in place and positioned properly before driving.
Main Menu Table of Contents Protecting Adults 5. Fasten and Position the Seat Belts Insert the latch plate into the buckle, then tug on the belt to make sure the belt is securely latched. Also check that the belt is not twisted, because a twisted belt can cause serious injuries in a crash. If necessary, pull up on the belt again to remove any slack from the shoulder part, then check that the belt rests across the center of your ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ０ chest and over your shoulder.
Main Menu Table of Contents Protecting Adults Never place the shoulder portion of a lap/shoulder belt under your arm or behind your back.This could cause very serious injuries in a crash. See page 42 for additional information about your seat belt system and how to take care of your belts. 6. Adjust the Steering Wheel If a seat belt does not seem to work as it should, it may not protect the occupant in a crash. No one should sit in a seat with an inoperative seat belt.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ Protecting Adults 7. Maintain a Proper Sitting Position After all occupants have adjusted their seats and put on seat belts, it is very important that they continue to sit upright, well back in their seats, with their feet on the floor, until the car is parked and the engine is off. Sitting improperly can increase the chance of injury during a crash.
Main Menu Table of Contents Protecting Adults Advice for Pregnant Women Pregnant women should also sit upright and as far back as possible from the steering wheel or dashboard. This will reduce the risk of injuries to both the mother and her unborn child that can be caused by a crash or an inflating airbag. Each time you have a check-up, ask your doctor if it's okay for you to drive. Additional Safety Precautions Two people should never use the same seat belt.
Main Menu Table of Contents Protecting Adults Do not place hard or sharp objects between yourself and an airbag. Carrying hard or sharp objects on your lap, or driving with a pipe or other sharp object in your mouth, can result in injuries if your airbags inflate. Do not attach or place objects on the front airbag covers.
Main Menu ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Table of Contents Protecting Children Children who are unrestrained or improperly restrained can be seriously injured or killed in a crash. Any child too small for a seat belt should be properly restrained in a child seat. A larger child should be properly restrained with a seat belt. Children depend on adults to protect them. However, despite their best intentions, many parents and other adults may not know how to properly protect young passengers.
Main Menu Table of Contents Protecting Children Children Should Sit in the Back Seat According to accident statistics, children of all ages and sizes are safer when they are restrained in the back seat, not the front seat. The National Highway Traffic Safety Administration and Transport Canada recommend that all children ages 12 and under be properly restrained in the back seat. In the back seat, children are less likely to be injured by striking hard interior parts during a collision or hard braking.
Main Menu Table of Contents Protecting Children U.S. Models Canadian Models To remind you of the passenger's airbag hazards, and that children must be properly restrained in the back seat, your car has warning labels on the dashboard and on the driver's and front passenger's visors. Please read and follow the instructions on these labels. To remind you of the airbag hazards, your car has warning labels on the driver's and front passenger's visors.
Main Menu Table of Contents Protecting Children If You Must Drive with Several Children Your car has two seating positions in the back seat where children can be properly restrained. If you ever have to carry more than two children in your car: Place the largest child in the front seat, provided the child is large enough to wear a seat belt properly (see page 37). Move the vehicle seat as far to the rear as possible (see page 13). Have the child sit upright and well back in the seat (see page 18).
Main Menu Table of Contents Protecting Children General Guidelines for Using Child Seats The following pages give general guidelines for selecting and installing child seats for infants and small children. Selecting a Child Seat To provide proper protection, a child seat should meet three requirements: 1. 2. The child seat should meet safety standards. The child seat should meet Federal Motor Vehicle Safety Standard 213 (FMVSS 213) or Canadian Motor Vehicle Safety Standard 213 (CMVSS 213).
Main Menu Table of Contents Protecting Children 3. The child seat should fit the vehicle seating position (or positions) where it will be used. Due to variations in the design of child seats, vehicle seats, and seat belts, all child seats will not fit all vehicle seating positions. However, Acura is confident that one or more child seat models can fit and be properly installed in all recommended seating positions in your car.
Main Menu Table of Contents Protecting Children Placing a Child Seat This page briefly summarizes Acura's recommendations on where to place rear-facing and forward-facing child seats in your car. Airbags Pose Serious Risks to Children The passenger's airbag inflates with enough force to kill or seriously injure an infant in a rear-facing child seat. A small child in a forward-facing child seat is also at risk.
Main Menu Table of Contents Protecting Children Installing a Child Seat After selecting a proper child seat, and a good position to install the seat, there are three main steps in installing the seat: To provide security during normal driving maneuvers as well as during a collision, we recommend that parents secure a child seat as firmly as possible. 1.Secure the child seat to the car with a seat belt. All child seats must be secured to the car with the lap part of a lap/shoulder belt.
Main Menu Table of Contents０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Protecting Children Protecting Infants Placing a rear-facing child seat in the front seat can result in serious injury or death if the airbags inflate. Always place a rear-facing child seat in the back seat, not the front. Child Seat Type Only a rear-facing child seat provides proper support for a baby's head, neck, and back. Infants up to about one year of age must be restrained in a rear-facing child seat.
Main Menu Table of Contents Protecting Children Rear-Facing Child Seat Installation The lap/shoulder belts in the back seats have a locking mechanism that must be activated to secure a child seat. The following pages provide instructions and tips on how to secure a rear-facing child seat with this type of seat belt. 1. With the child seat in the desired back seating position, route the belt through the child seat according to the seat maker's instructions, then insert the latch plate into the buckle.
Main Menu Table of Contents Protecting Children To deactivate the locking mechanism and remove a child seat, unlatch the buckle, unroute the seat belt, and let the belt fully retract. 4. After confirming that the belt is locked, grab the shoulder part of the belt near the buckle and pull up to remove any slack from the lap part of the belt. Remember, if the lap part of the belt is not tight, the child seat will not be secure.
Main Menu Table of Contents Protecting Children Rear-Facing Child Seat Installation Tips For proper protection, an infant must ride in a reclined, or semi-reclined position. To determine the proper reclining angle, check with the baby's doctor or follow the seat maker's recommendations. To achieve the desired reclining angle, it may help to put a rolled up towel under the toe of the child seat, as shown.
Main Menu Table of Contents Protecting Children Protecting Small Children Of the different seats available, we recommend those that have a fivepoint harness system as shown. We also recommend that a small child stay in the child seat as long as possible, until the child reaches the weight or height limit for the seat. Child Seat Type A child who can sit up without support, and who fits within the child seat maker's weight and height limits, should be restrained in a forward-facing, upright child seat.
Main Menu Table of Contents ３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Protecting Children Child Seat Installation Improperly placing a forwardfacing child seat in the front seat can result in serious injury or death if the airbags inflate. If you must place a forwardfacing child seat in front, move the vehicle seat as far back as possible and properly restrain the child.
Main Menu Table of Contents Protecting Children 2. To activate the lockable retractor, slowly pull the shoulder part of the belt all the way out until it stops, then let the belt feed back into the retractor (you might hear a clicking noise as the belt retracts). 3. After the belt has retracted, tug on it. If the belt is locked, you will not be able to pull it out. If you can pull the belt out, it is not locked and you will need to repeat these steps. 4.
Main Menu Table of Contents Protecting Children To deactivate the locking mechanism in order to remove a child seat, unlatch the buckle, unroute the seat belt, and let the belt fully retract. Additional Precautions for Small Children Never hold a small child on your lap. If you are not wearing a seat belt in a crash, you could be thrown forward into the dashboard and crush the child. If you are wearing a seat belt, the child can be torn from your arms during a crash.
Main Menu Table of Contents０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Protecting Children Protecting Larger Children When a child reaches the recommended weight or height limit for a forward-facing child seat, the child should sit in one of the back seats and wear a lap/shoulder belt. If a child is too short for the shoulder part of the belt to properly fit, we recommend that the child use a booster seat until tall enough to use the seat belt without a booster.
Main Menu Table of Contents Protecting Children If the shoulder part of the belt rests over the child's collarbone and against the center of the chest, as shown, the child is large enough to wear the seat belt. However, if the belt touches or crosses the child's neck, the child needs to use a booster seat. Do not let a child wear a seat belt across the neck. This could result in serious neck injuries during a crash. Do not let a child put the shoulder part of a seat belt behind the back or under the arm.
Main Menu Table of Contents Protecting Children A child may continue using a booster seat until the tops of the ears are even with the top of the seat-back. A child of this height should be tall enough to use the lap/shoulder belt without a booster. When Can a Larger Child Sit in Front The National Highway Traffic Safety Administration and Transport Canada recommend that all children ages 12 and under be properly restrained in a back seat.
Main Menu Table of Contents Protecting Children If you decide that a child can safely ride up front, be sure to: Using Child Seats with Tethers CARGO AREA Carefully read the owner's manual and make sure you understand all seat belt instructions and all safety information. Move the vehicle seat to the rearmost position. Have the child sit up straight, back against the seat, and feet on or near the floor. Check that the child's seat belt is properly positioned and secured. Supervise the child.
Main Menu Table of Contents Protecting Children If you are not sure how to reinstall the tether hardware, contact your Acura dealer. When reinstalling tether hardware, make sure the toothed washer is on the bottom of the bolt. Tighten the bolt to: 16 lbf.ft (22 N.m , 2.2 kgf.m) If a torque wrench was not used, see your Acura dealer as soon as possible to verify proper reinstallation.
Main Menu Table of Contents Additional Information About Your Seat Belts Seat Belt System Components Your seat belt system includes lap/ shoulder belts in all four seating positions. The seat belt system also includes a light on the instrument panel to remind you and your passengers to fasten your belts. If the driver's seat belt is not fastened before the ignition is turned ON (II), the light will come on and a beeper will also sound.
Main Menu Table of Contents Additional Information About Your Seat Belts All seat belts have an emergency locking retractor. In normal driving, the retractor lets you move freely in your seat while it keeps some tension on the belt. During a collision or sudden stop, the retractor automatically locks the belt to help restrain your body. The seat belts in all seating positions except the driver's have an additional locking mechanism that must be activated to secure a child seat.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Additional Information About Your Seat Belts If a seat belt is worn during a crash, you should have your dealer inspect the belt, and replace it if necessary. A belt that has been worn during a crash may not provide the same level of protection in a subsequent crash. The dealer should also inspect the anchors for damage and replace them if needed.
Main Menu Table of Contents Additional Information About Your SRS SRS Components Your Supplemental Restraint System (SRS) includes: Two front airbags. The driver's airbag is stored in the center of the steering wheel; the front passenger's airbag is stored in the dashboard. Both are marked "SRS AIRBAG." An indicator light on the instrument panel that alerts you to a possible problem with the system (see page 47).
Main Menu Table of Contents Additional Information About Your SRS After a crash, you may see what looks like smoke. This is actually powder from the airbag's surface. Although the powder is not harmful, people with respiratory problems may experience some temporary discomfort. If this occurs, get out of the car as soon as it is safe to do so. Since both airbags use the same sensors, both airbags normally inflate at the same time. However, it is possible for only one airbag to inflate.
Main Menu Table of Contents Additional Information About Your SRS How the SRS Indicator Light If the light comes on or flashes on Works and off while you drive. The purpose of the SRS S R S light is to alert you to a ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ If you see any of these indications, potential problem with your your airbags may not deploy when Supplemental Restraint System. you need them. See your Acura dealer as soon as possible.
Main Menu Table of Contents Additional Information About Your SRS Additional Safety Precautions Do not attempt to deactivate your airbags. Together, airbags and seat belts provide the best protection in a moderate to severe frontal collision. Do not tamper with SRS components or wiring for any reason. Tampering could cause the airbags to deploy, possibly causing very serious injury. See page 131 for further information and precautions relating to your SRS.
Main Menu Table of Contents０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Carbon Monoxide Hazard Your car's exhaust contains carbon monoxide gas. You should have no problem with carbon monoxide entering the car in normal driving if you maintain your car properly. Have the exhaust system inspected for leaks whenever: The car is raised for an oil change. Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and even kill you. Avoid any enclosed areas or activities that expose you to carbon monoxide.
Main Menu Table of Contents Safety Labels These labels are in the locations shown. They warn you of potential hazards that could cause serious injury. Read these labels carefully. DASH BOARD U.S. models only SUN VISOR U.S. models If a label comes off or becomes hard to read, contact your Acura dealer for a replacement.
Main Menu Instruments and Controls This section gives information about the controls and displays that contribute to the daily operation of your Acura. All the essential controls are within easy reach. Control Locations............................ 52 Indicator Lights................................ 53 Gauges.............................................. 58 Speedometer................................ 58 Tachometer.................................. 58 Odometer......................................
Main Menu Table of Contents Control Locations DOOR LOCK SWITCHES/ HATCH LOCK SWITCH (P. 75) MIRROR CONTROLS (P. 86) INDICATOR LIGHTS (P. 53) GAUGES (P. 58) DIGITAL CLOCK (P. 88) HEATING/COOLING CONTROLS (P. 94) POWER WINDOW SWITCHES (P. 84) AUDIO SYSTEM (P. 102) FUEL FILL DOOR RELEASE (P. 124) SHIFT LEVER (P. 138, 140) HOOD RELEASE HANDLE (P. 125) Instruments and Controls PARKING BRAKE (P.
Main Menu Table of Contents Indicator Lights The instrument panel has many indicators to give you important information about your car.
Main Menu Table of Contents Indicator Lights Seat Belt Reminder Light This indicator lights when you turn the ignition switch ON (II). It is a reminder to you and your passengers to protect yourselves by fastening the seat belts. A beeper also sounds if you have not fastened your seat belt. If you do not fasten your seat belt, the beeper will stop after a few seconds but the light stays on until you do. Both the light and the beeper stay off if you fasten your seat belt before turning on the ignition.
Main Menu Table of Contents Indicator Lights Supplemental Restraint SRS System Indicator This indicator lights when you turn the ignition switch ON (II). If it comes on at any other time, it indicates a problem in the supplemental restraint system. For complete information, see page 47. Charging System Indicator If this light comes on when the engine is running, the battery is not being charged. For complete information, see page 236.
Main Menu Table of Contents Indicator Lights Turn Signal and Hazard Warning Indicators The left or right turn signal light blinks when you signal a lane change or turn. If the light does not blink or blinks rapidly, it usually means one of the turn signal bulbs is burned out (see page 208). Replace the bulb as soon as possible, since other drivers cannot see that you are signalling. When you turn on the Hazard Warning switch, both turn signal lights blink.
Main Menu Table of Contents Indicator Lights High Beam Indicator This light comes on with the high beam headlights. See page 62 for information on the headlight controls. On Canadian models, this indicator comes on with reduced brightness when the Daytime Running Lights (DRL) are on (see page 62). Immobilizer System Indicator This indicator comes on for a few seconds when you turn the ignition switch ON (II). It will then go off if you have inserted a properly-coded ignition key.
Main Menu Table of Contents Gauges TEMPERATURE GAUGE TACHOMETER SPEEDOMETER TRIP METER RESET BUTTON ODOMETER Speedometer U.S. Models This shows your speed in miles per hour (mph). The smaller inner numbers are the speed in kilometers per hour (km/h). Canadian Models This shows your speed in kilometers per hour (km/h). The smaller inner numbers are the speed in miles per hour (mph).
Main Menu Table of Contents Gauges TEMPERATURE GAUGE TACHOMETER TRIP METER RESET BUTTON Fuel Gauge This shows how much fuel you have. It is most accurate when the car is on level ground. It may show slightly more or less than the actual amount when you are driving on curvy or hilly roads. SPEEDOMETER ODOMETER FUEL GAUGE TRIP METER Temperature Gauge This shows the temperature of the engine's coolant.
Main Menu Table of Contents Gauges Maintenance Required Indicator MAINT REQD This indicator reminds you that it is time to take your car in for scheduled maintenance. Refer to the Maintenance Schedules for Normal and Severe Driving Conditions on pages 162 — 166 . For the first 6,000 miles (9,600 km) after the Maintenance Required Indicator is reset, it will come on for two seconds when you turn the ignition switch ON (II).
Main Menu Table of Contents Controls Near the Steering Wheel The two levers on the steering column contain controls for driving features you use most often. The left lever controls the turn signals, headlights, and high beams. The right lever controls the windshield washers and wipers.
Main Menu Table of Contents Controls Near the Steering Wheel Headlights If you leave the lights on with the ignition switch in ACCESSORY (I) or LOCK (0), you will hear a reminder beeper when you open the driver's door. To flash the high beams, pull the turn signal lever back lightly, then release it. The high beams will come on and go off. The high beams will stay on for as long as you hold the lever back, no matter what position the headlight switch is in.
Main Menu Table of Contents Controls Near the Steering Wheel Instrument Panel Brightness Turn Signals To signal a lane change, push lightly on the turn signal lever in the proper direction and hold it. The lever will return to the center position as soon as you release it. TURN SIGNAL LEVER The knob on the dashboard to the right of the steering column controls the brightness of the instrument panel lights. Turn the knob to adjust the brightness. Signal a turn or lane change with this lever.
Main Menu Table of Contents Controls Near the Steering Wheel Windshield Wipers The right lever controls the windshield wipers and washers. The rotary switch at the end of the lever has three positions: INT: intermittent : low speed : high speed In intermittent, the wipers operate every few seconds. In low speed and high speed, the wipers run continuously. Instruments and Controls Windshield Washers To operate the wipers in mist mode, push the control lever down.
Main Menu Table of Contents Controls Near the Steering Wheel Rear Window Wiper and Washer Hazard Warning Rear Window Defogger Push the red button under the center air vent to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your car is disabled.
Main Menu Table of Contents Controls Near the Steering Wheel Steering Wheel Adjustment See page 17 for important safety information about how to properly ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ position the steering wheel. The defogger wires on the inside of Make any steering wheel adjustment the rear window can be accidentally before you start driving. damaged. When cleaning the glass, always wipe side to side. Make sure the rear window is clear and you have good visibility before starting to drive.
Main Menu Table of Contents Controls Near the Steering Wheel, Steering Wheel Controls Cruise Control LS, GS and GS-R models Cruise control allows you to maintain a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It should be used for cruising on straight, open highways. It is not recommended for 3. Push the lever up to lock the conditions such as city driving, steering wheel in that position.
Main Menu Table of Contents Steering Wheel Controls The cruise control may not hold the set speed when you are going up and down hills. If your speed increases going down a hill, use the brakes to slow down to the desired speed. This will cancel the cruise control. To resume the set speed, press the RESUME/accel button. The CRUISE CONTROL light on the instrument panel comes on. Using the Cruise Control RESUME/ accel SET/decel 1.
Main Menu Table of Contents Steering Wheel Controls Changing the Set Speed You can increase the set cruising speed in either of two ways: Press and hold the RESUME/ accel button. The car will accelerate. When you reach the desired cruising speed, release the button. Push on the accelerator pedal. Accelerate to the desired cruising speed and press the SET/decel button. You can decrease the set cruising speed in either of two ways: Press and hold the SET/decel button. The car will decelerate.
Main Menu Table of Contents Steering Wheel Controls Cancelling the Cruise Control You can cancel the cruise control in any of these ways: Tap the brake or clutch pedal. Press the SET/decel and RESUME/accel buttons at the same time. Press the Cruise Control Master Switch. When you tap the brake or clutch pedal, or press the SET and RESUME buttons at the same time, the CRUISE CONTROL light on the instrument panel will go out and the car will begin to slow down.
Main Menu Table of Contents Keys and Locks Keys VALET KEY (GREY) MASTER KEY (BLACK) You should have received a key number plate with your set of keys. You will need this number if you have to get a lost key replaced. Keep the plate stored in a safe place. When replacing keys, use only Acura-approved key blanks. KEY NUMBER PLATE Your car comes with two master keys and a valet key.
Main Menu Table of Contents Keys and Locks These keys contain electronic circuits that are activated by the Immobilizer System. They will not work to start the engine if the circuits are damaged. Protect the keys from direct sunlight, high temperature, and high humidity. Do not drop the keys or set heavy objects on them. Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth. The keys do not contain batteries. Do not try to take them apart.
Main Menu Table of Contents Keys and Locks Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your car undriveable. If you have lost your key and you cannot start the engine, contact your Acura dealer. As required by the FCC: This device complies with Part 15 of the FCC rules.
Main Menu ０３／０７／１０ Table of Contents １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Keys and Locks LOCK (0) — You caii insert or remove the key only in this position. To switch from ACCESSORY to LOCK, you must push the key in slightly as you turn it. If your car has an automatic transmission, the shift lever must also be in Park. The antitheft lock will lock the steering column when you remove the key. If the front wheels are turned, the anti-theft lock may sometimes make it difficult to turn the key from LOCK to ACCESSORY.
Main Menu Table of Contents Keys and Locks Door Locks LOCK TAB The doors can also be locked and unlocked from the outside with the key. Power Door/Hatch Locks MASTER DOOR AND HATCH LOCK SWITCH SE model When you push in the lock tab on the driver's door, that door and the hatch will lock. LS, GS, GS-R and Type-R models When you push in the lock tab on the driver's door, both doors and the hatch will lock. Each door has a lock tab above the inside door handle.
Main Menu Table of Contents Keys and Locks LS, GS, GS-R and Type-R models Each door has a master door and hatch lock switch. Either switch locks and unlocks both doors and the hatch. Push the switch down to lock both doors and the hatch and up to unlock them. To lock the passenger's door when getting out of the car, push the lock tab in and close the door. To lock the driver's door, pull the outside door handle and push the lock tab in or push the master switch down.
Main Menu Table of Contents Keys and Locks LEVER See page 132 for cargo loading and weight limit information. Keep the hatch closed at all times while driving to avoid damaging the hatch and to prevent exhaust gas from getting into the interior. See Carbon Monoxide Hazard on page 49. LOCK MASTER KEY To open the hatch, slide the lever behind the hatch's back edge until it releases the hatch and lift the hatch. To close the hatch, push down on the hatch's back edge.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ Keys and Locks Glove Box An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt. Always keep the glove box closed while driving. Open the glove box by pulling the bottom of the handle. Close it with a firm push. Lock or unlock the glove box with the master key.
Main Menu Table of Contents Seat Adjustments Front Seat Adjustments See pages 13 — 14 for important safety information and warnings about how to properly position seats and seat-backs. Make all seat adjustments before you start driving. To adjust the seat forward and backward, pull up on the lever under the seat cushion's front edge. Move the seat to the desired position and release the lever. Try to move the seat to make sure it is locked in position.
Main Menu Table of Contents Seat Adjustments Driver's Seat Height Adjustment Driver's Lumbar Support Except SE and Type-R models See pages 13 —14 for important safety information and warnings about how to properly position seats and seat-backs. Vary the lumbar support by moving the lever on the right side of the seat-back. Make all adjustments before you start driving. The height of your driver's seat is adjustable.
Main Menu Table of Contents Seat Adjustments Rear Seat Access To get into the back seat on the driver's side, pull up on the seat-back adjustment lever. RELEASE LEVER To get into the back seat on the passenger's side, push forward on the release lever at the base of the seat-back. The entire seat will slide forward at the same time to allow easier entry to the back seat. After you return the seat-back to the upright position, push the whole seat backwards until it latches.
Main Menu Table of Contents Seat Adjustments Head Restraints See page 15 for important safety information and a warning about how to properly position the head restraints. RELEASE BUTTON The front head restraints adjust for height. You need both hands to adjust the restraint. Do not attempt to adjust it while driving. To raise it, pull upward. To lower the restraint, push the release button sideways and push the restraint down.
Main Menu Table of Contents Folding Rear Seat, Cargo Area Cover Folding Rear Seat To lock the seat-back upright, push the seat-back firmly against its latch. Tug on the seat-back to make sure it is latched. Cargo Area Cover MOUNTING ROD Make sure all items in the cargo area are secured. Loose items can fly forward and cause injury if you have to brake hard. See Carrying Cargo on page 132. RELEASE TAB The back of the rear seat folds down to give you more cargo space. Each side folds down separately.
Main Menu ０３／０７／１０ Table of Contents １６：１１：０９ ３１Ｓ５Ａ９３０ Power Windows Your car's windows are electricallypowered. Turn the ignition switch to ON (II) to raise or lower any window. MAIN SWITCH Closing a power window on someone's hands or fingers can cause serious injury. Each door has a switch that controls its window. To open the window, push the switch down and hold it. Release the switch when you want the window to stop. Close the window by pushing the switch up and holding it.
Main Menu Table of Contents Power Windows, Moonroof The master control panel also contains these extra features: AUTO — To open the driver's window fully, push the window switch firmly down and release it. The window automatically goes all the way down. To stop the window from going all the way down, push the window switch up briefly. To open the driver's window only partially, push the window switch down lightly and hold it. The window will stop as soon as you release the switch.
Main Menu Table of ３１Ｓ５Ａ９３０ Contents ３／０７／１０ １６：１１：０９ ００２１ Moonroof, Mirrors Mirrors Adjusting the Power Mirrors SELECTOR SWITCH Closing the moonroof on someone's hands or fingers can cause serious injury. Make sure passengers are clear of the moonroof before closing it. NOTICE If you try to open the moonroof in below-freezing temperatures, or when it is covered with snow or ice, you can damage the moonroof panel or motor. TAB Keep the inside and outside mirrors clean and adjusted for best visibility.
Main Menu Table of Contents Mirrors, Parking Brake Parking Brake ADJUSTMENT SWITCH 3. Push the appropriate edge of the adjustment switch to move the mirror right, left, up or down. 4. When you finish, move the selector switch to the center (off) position. This turns off the adjustment switch so you can't move a mirror out of position by accidentally bumping the switch. PARKING BRAKE LEVER NOTICE Driving the car with the parking brake applied can damage the rear brakes and axles.
Main Menu Table of Contents Digital Clock M H RESET 3. Press and hold the H button until the hour advances to the desired hour. 4. Press and hold the M button until the numbers advance to the desired minutes. The digital clock displays the time with the ignition switch ON (II). To see the time with the ignition off, press and hold the wide button next to the clock. To set the clock: 1. Turn the ignition switch ON (II) to display the time. 2.
Main Menu Table of Contents Beverage Holder Push To open the beverage holder, push on the front to get it pop out slightly. Then pull it out the rest of the way. To close it, push it until it latches. Be careful when you are using the beverage holder. A spilled liquid that is very hot can scald you or your passengers. Spilled liquids can also damage the upholstery, carpeting, and electrical components in the interior.
Main Menu Table of Contents Console Compartment, Cigarette Lighter Cigarette Lighter Console Compartment CONSOLE COMPARTMENT To open the console compartment, pull up the front edge of the lid. To close, lower the lid and push it down until it latches. Instruments and Controls CARD HOLDER The pocket on the underside of the console compartment lid can be used to hold cards. CIGARETTE LIGHTER The ignition switch must be in ACCESSORY (I) or ON (II) for the cigarette lighter to work.
Main Menu Table of Contents Ashtrays ASHTRAY NOTICE Use the ashtray only for cigarettes, cigars, and other smoking materials. To prevent a possible fire and damage to your car, don't put paper or other things that can burn in the ashtray. ASHTRAY Open the front ashtray by pulling on the front. Push it in to close it. To remove the ashtray for emptying, push down on the metal plate inside, then pull the ashtray out completely. The rear ashtray is at the rear end of the center console.
Main Menu Table of Contents Interior Lights Getting Light Spotlights Cargo Area Light LS, GS and GS-R models Turn on the spotlight by pushing the button next to each light. Push the button again to turn it off. The cargo area light has a twoposition switch. In the OFF (down) position, the light does not come on. In the ON (up) position, the light comes on when you open the hatch. DOOR ACTIVATED The ceiling light has a three-position switch. In the OFF position, the light does not come on.
Main Menu Comfort and Convenience Features The heating and air conditioning* systems in your Acura provide a comfortable driving environment in all weather conditions. The standard audio system has many features. This section describes those features and how to use them. (If you selected an optional audio system, refer to the operating instructions that came with it.) Your Acura has an anti-theft audio system that requires a code number to enable it. * Air conditioning is optional on the Type-R model.
Main Menu Table of Contents Heating and Cooling Proper use of the Heating and Cooling system can make the interior dry and comfortable, and keep the windows clear for best visibility. (Type-R model only) If your car does not have air conditioning, it can be installed at any time. Your dealer will install a Genuine Acura air conditioning system that meets Acura's high quality standards and is designed to exactly fit your car. Please contact your dealer for more information.
Main Menu Table of Contents Heating and Cooling Mode Buttons Use the MODE buttons to select the vents the air flows from. Some air will flow from the dashboard corner vents in all modes. Air flows from the center and corner vents in the dashboard. Air flow is divided between the vents in the dashboard and the floor vents. Air flows from the floor vents. Air flow is divided between the floor vents and the defroster vents at the base of the windshield.
Main Menu Table of Contents Heating and Cooling Vent Controls CENTER VENT SIDE VENT How to Use the System This section covers how to set up the system controls for ventilation, heating, cooling, dehumidifying, and defrosting. The engine must be running for the heater and air conditioning to generate hot and cold air. The heater uses engine coolant to warm the air. If the engine is cold, it will be several minutes before you feel warm air coming from the system.
Main Menu Table of Contents Heating and Cooling It is best to leave the system in Fresh Air mode under almost all conditions. Keeping the system in Recirculation mode, particularly with the A/C off, can cause the windows to fog up. Switch to Recirculation mode when you are driving through smoky or dusty conditions, then switch back to Fresh Air mode when the condition clears. The outside air intakes for the heating and cooling system are at the base of the windshield.
Main Menu Table of Contents Heating and Cooling To Cool with A/C 1. Turn on the A/C by pressing the button. The light in the button should come on when a fan speed is selected. 2. Make sure the temperature control lever is set to maximum cool. 3. Select 4. If the outside air is humid, select Recirculation mode. If the outside air is dry, select Fresh Air mode. 5. Set the fan to the desired speed.
Main Menu Table of Contents Heating and Cooling If the interior is very warm from being parked in the sun, you can cool it down more rapidly by setting up the controls this way: 1. Start the engine. 2. Turn on the A/C by pressing the button. Make sure the temperature control lever is all the way to the left. 3. Set the fan to maximum speed. 4. Open the windows partially. Select and Fresh Air mode.
Main Menu Table of Contents Heating and Cooling To Defog and Defrost To remove fog from the inside of the windows: 1. Switch the fan on. 2. Turn on the air conditioning. 3. Select Fresh Air mode and 4. Adjust the temperature control lever so the air flow from the defroster vents feels warm. 5. Turn on the rear window defogger to help clear the rear window.
Main Menu Table of Contents Heating and Cooling To remove exterior frost or ice from the windshield and side windows after the car has been sitting out in cold weather: 1. Start the engine. 2. Select the Fresh Air mode and 3. Switch the fan and temperature controls to maximum. To rapidly remove exterior frost or ice from the windshield (on very cold days), first select the Recirculation mode. Once the windshield is clear, select the Fresh Air mode to avoid fogging the windows.
Main Menu Table of Contents Audio System AM/FM/CD Audio System Your Acura's audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations. AM/FM 1-2 BUTTON TUNE BAR The anti-theft feature will disable the system if it is disconnected from the vehicle's battery.
Main Menu Table of Contents Audio System Operating the Radio The ignition switch must be in ACCESSORY (I) or ON (II) to operate the audio system. Turn the system on by pushing the PWR/ VOL knob. Adjust the volume by turning the same knob. The antenna extends automatically. The system turns off and the antenna retracts when you turn the ignition switch to LOCK (0). The band and frequency that the radio was last tuned to is displayed. To change bands, press the A M / F M 1.2 button.
Main Menu Table of Contents Audio System To store a frequency: 1. Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each Preset button. AM/FM 1-2 BUTTON TUNE BAR 2. Use the TUNE or SEEK function to tune the radio to a desired station. 3. Pick the Preset button you want for that station. Press the button and hold it until you hear a beep. 4. Repeat steps 1 to 3 to store a total of six stations on AM and twelve on FM.
Main Menu Table of Contents Audio System AUTO SELECT — If you are traveling far from home and can no longer receive the stations you preset, you can use the Auto Select feature to find stations in the local area. To activate Auto Select, press the A. SEL/RPT button. A. SEL will flash in the display, and the system will go into scan mode for several seconds. It automatically scans both bands, looking for stations with strong signals.
Main Menu Table of Contents Audio System Adjusting the Sound Bass, Treble, Balance, and Fader are each adjustable. You select which of these you want to adjust by pressing the MODE button several times. The selected mode, BAS, TRE, FAD, or BAL is shown in the display. Balance/Fader — These two modes adjust the strength of the sound coming from each speaker. BAL adjusts the side-to-side strength, while FAD adjusts the front-to-back strength. Select BAL or FAD by pressing the MODE button.
Main Menu Table of Contents Audio System Radio Frequencies Your Acura's radio can receive the complete AM and FM bands. Those bands cover these frequencies: AM band: 530 to 1,710 kilohertz FM band: 87.7 to 107.9 megahertz Radio stations on the AM band are assigned frequencies at least ten kilohertz apart (530, 540, 550). Stations on the FM band are assigned frequencies at least 0.2 megahertz apart (87.9, 88.1, 88.3). Stations must use these exact frequencies.
Main Menu Table of Contents Audio System Electrical interference from passing vehicles and stationary sources can cause temporary reception problems. As required by the FCC: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills.
Main Menu Table of Contents Audio System Operating the CD Player You operate the CD player with the same controls used for the radio. With the system on, insert the disc into the CD slot. Push the disc in halfway, the drive will pull it in the rest of the way and begin to play. The number of the track that is playing is shown in the display. AM/FM1-2 BUTTON CD BUTTON CD SLOT CD INDICATOR You can also play 3-inch (8-cm) discs without using an adapter ring. In all cases, play only standard round discs.
Main Menu Table of Contents Audio System If you turn the system off while a CD is playing, either with the PWR/VOL knob or by turning off the ignition, the disc will stay in the drive. When you turn the system back on, the CD will begin playing where it left off. Press the eject button to remove the disc from the drive. If you eject the disc, but do not remove it from the slot, the system will automatically reload the disc after 15 seconds and put the CD player in pause mode.
Main Menu Table of Contents Audio System Operating the CD Changer (Optional) A Compact Disc changer is available for your car. It holds up to six discs, providing several hours of continuous entertainment. You operate this CD changer with the same controls used for the in-dash CD player. Load the desired CDs in the magazine and load the magazine in the changer according to the instructions that came with the unit. Play only standard round discs. Oddshaped CDs may jam in the drive or cause other problems.
Main Menu Table of Contents Audio System Protecting Compact Discs Handle a CD by its edges; never touch either surface. Contamination from fingerprints, liquids, felt-tip pens, and labels can cause the CD to not play properly, or possibly jam in the drive. When a CD is not being played, store it in its case to protect it from dust and other contamination. To prevent warpage, keep CDs out of direct sunlight and extreme heat. Comfort and Convenience Features To clean a disc, use a clean soft cloth.
Main Menu Table of Contents Audio System CD Player Error Indications If you see an error indication in the display while operating the CD player, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Acura dealer.
Main Menu Table of Contents Audio System CD Changer Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Acura dealer.
Main Menu Table of Contents Audio System Operating the Cassette Player (Optional) The cassette system features Dolby B* noise reduction, automatic sensing of chromium-dioxide (CrO2) tape, and autoreverse for continuous play. The tape direction indicator will light to show you which side of the cassette is playing. The indicates the side you inserted facing upward is now playing. If you want to play the other side, press the PROG button.
Main Menu Table of Contents Audio System Tape Search Functions With a cassette playing, you can use the FF, REW, TMS, or REPEAT function to find a desired program. FAST FORWARD/ REWIND FF/REW — Fast Forward and Rewind move the tape rapidly. Press and release the side of the TUNE bar to fast forward the tape, or the side to rewind. You will see FF or REW flashing in the display. To stop fast forward or rewind, press the PLAY button.
Main Menu Table of Contents Audio System TMS — The Tape Music Search function allows you to find the beginning of a song or passage. To activate TMS, press the SEEK bar. Press the side to advance to the beginning of the next song or passage, or the side to return to the beginning of the current song or passage. FF or REW will flash in the display as the tape moves. When the system reaches the beginning of the next song or passage (FF), or the beginning of the current one (REW), it goes back to PLAY mode.
Main Menu Table of Contents Audio System Caring for the Cassette Player The cassette player picks up dirt and oxides from the tape. This contamination builds up over time and causes the sound quality to degrade. To prevent this, you should clean the player after every 30 hours of use. Your dealer has a cleaning kit available. If you do not clean the cassette player regularly, it may eventually become impossible to remove the contamination with a normal cleaning kit.
Main Menu Table of Contents Audio System Theft Protection Your car's audio system will disable itself if it is disconnected from electrical power for any reason. To make it work again, the user must enter a specific five-digit code in the Preset buttons. Because there are hundreds of number combinations possible from five digits, making the system work without knowing the exact code is nearly impossible. You should have received a card that lists your audio system's code number and serial number.
Main Menu 120
Main Menu Before Driving Before you begin driving your Acura, you should know what gasoline to use, and how to check the levels of important fluids. You also need to know how to properly store luggage or packages. The information in this section will help you. If you plan to add any accessories to your car, please read the information in this section first. General Precautions...................... 122 Break-in Period.............................. 123 Gasoline..........................................
Main Menu Table of Contents General Precautions Curbs and steep inclines could damage the front and rear bumpers. Low curbs that do not affect the average car may be high enough to hit the bumper on your Acura. The front or rear bumper may scrape when trying to drive onto an incline, such as a steep driveway or trailer ramps. Type-R model Your Acura is designed to give you optimum handling and performance on well-maintained roads. As part of this design, your car has a minimum of ground clearance.
Main Menu Table of Contents Break-in Period, Gasoline Break-in Period Help assure your car's future reliability and performance by paying extra attention to how you drive during the first 600 miles (1,000 km). During this period: Avoid full-throttle starts and rapid acceleration. Avoid hard braking. New brakes need to be broken-in by moderate use for the first 200 miles (300 km). You should follow these same recommendations with an overhauled or exchanged engine, or when the brakes are relined.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Service Station Procedures Filling the Fuel Tank Pull Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. Stop the engine and keep heat, sparks, and flame away. Handle fuel only outdoors. Wipe up spills immediately. 4. Stop filling the tank after the fuel nozzle automatically clicks off. Do not try to "top off" the tank, leave some room for the fuel to expand with temperature changes.
Main Menu Table of Contents Service Station Procedures 5. Screw the fuel fill cap back on, tighten it until it clicks at least three times. If you do not properly tighten the cap, the Malfunction Indicator Lamp may come on (see page 237). Opening the Hood 6. Push the fuel fill door closed until it latches. LATCH HOOD RELEASE HANDLE 1. Shift to Park or Neutral and set the parking brake. Pull the hood release handle located under the lower left corner of the dashboard. The hood will pop up slightly.
Main Menu Table of Contents Service Station Procedures If you can open the hood without lifting the hood latch handle, or the hood latch handle moves stiffly or does not spring back as before, the mechanism should be cleaned and lubricated (see page 187). To close the hood, lift it up slightly to remove the support rod from the hole. Put the support rod back into its holding clip. Lower the hood to about a foot (30 cm) above the fender, then let it drop.
Main Menu Table of Contents Service Station Procedures Oil Check DIPSTICK Check the engine oil level every time you fill the car with fuel. Wait a few minutes after turning the engine off before you check the oil. 2. Wipe the dipstick with a clean cloth or paper towel. 3. Insert it all the way back in its tube. 1. Remove the dipstick (orange handle).
Main Menu Table of Contents Service Station Procedures Refer to Owner Maintenance Checks on page 169 for information on checking other items in your Acura. Engine Coolant Check MAX MIN UPPER MARK LOWER MARK RESERVE TANK 4. Remove the dipstick again and check the level. It should be between the upper and lower marks. If it is near or below the lower mark, see Adding Oil on page 171. Before Driving Look at the coolant level in the radiator reserve tank. Make sure it is between the MAX and MIN lines.
Main Menu Table of Contents Fuel Economy The condition of your car and your driving habits are the two most important things that affect the fuel mileage you get. Vehicle Condition Always maintain your car according to the maintenance schedule. This will keep it in top operating condition. An important part of that maintenance is the Owner Maintenance Checks (see page 169). For example, an underinflated tire causes more "rolling resistance," which uses fuel.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Accessories and Modifications Modifying your car, or installing some non-Acura accessories, can make your car unsafe. Before you make any modifications or add any accessories, be sure to read the following information. Accessories Your dealer has Genuine Acura accessories that allow you to personalize your car. These accessories have been designed and approved for your car, and are covered by warranty.
Main Menu Table of Contents Accessories and Modifications Modifications Do not remove any original equipment or modify your car in any way that would alter its design or operation. This could make your car unsafe and illegal to drive. In addition, any modifications that decrease ground clearance increase the chance of undercarriage parts striking a curb, speed bump, or other raised object, which could cause your airbags to deploy.
Main Menu Table of Contents Carrying Cargo CONSOLE COMPARTMENT FRONT DOOR POCKET Your car has several convenient storage areas so you can stow cargo safely. The glove box, and the pockets in the doors are designed for small, lightweight items. The cargo area is intended for larger, heavier items, In addition, the back seat can be folded down to allow you to carry more cargo or longer items.
Main Menu ０３／０７／１０ Table of Contents １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Carrying Cargo Load Limit The maximum load for your car is 700 lbs (325 kg). This figure includes the total weight of all occupants, cargo, accessories, and the tongue weight if you are towing a trailer. To figure out how much cargo you can carry: Overloading or improper loading can affect handling and stability and cause a crash in which you can be hurt or killed. Follow all load limits and other loading guidelines in this manual.
Main Menu Table of Contents Carrying Cargo Carrying Cargo in the Cargo Area or on a Roof Rack Distribute cargo evenly on the floor of the cargo area, placing the heaviest items on the bottom and as far forward as possible. If you fold down the back seat, tie down items that could be thrown about the car during a crash or sudden stop. Do not place items on the cargo area cover, or stack objects higher than the top of the back seat.
Main Menu Driving This section gives you tips on starting the engine under various conditions, and how to operate the 5-speed manual and automatic transmissions. It also includes important information on parking your car, the braking system, and facts you need if you are planning to tow a trailer. Preparing to Drive......................... 136 Starting the Engine........................ 137 Starting in Cold Weather at High Altitude..................... 137 5-speed Manual Transmission.....
Main Menu Table of Contents Preparing to Drive You should do the following checks and adjustments every day before you drive your car. 1. Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice. 2. Check that the hood and hatch are fully closed. 3. Visually check the tires. If a tire looks low, use a gauge to check its pressure. 4. Check that any items you may be carrying with you inside are stored properly or fastened down securely. Driving 5.
Main Menu Table of Contents Starting the Engine 1. Apply the parking brake. 2. In cold weather, turn off all electrical accessories to reduce the drain on the battery. 3. Manual Transmission: Push the clutch pedal down all the way. START (III) does not function unless the clutch pedal is depressed. Automatic Transmission: Make sure the shift lever is in Park. Press on the brake pedal. 4. Without touching the accelerator pedal, turn the ignition key to the START (III) position.
Main Menu ０３／０７／１０ Table of Contents １６：１１：０９ ３１Ｓ５Ａ９３０ 5-speed Manual Transmission Come to a full stop before you shift into Reverse. You can damage the transmission by trying to shift into Reverse with the car moving. Push down the clutch pedal, and pause for a few seconds before shifting into Reverse, or shift into one of the forward gears for a moment. This stops the gears so they won't "grind." The manual transmission is synchronized in all forward gears for smooth operation.
Main Menu Table of Contents 5-speed Manual Transmission Recommended Shift Points Drive in the highest gear that lets the engine run and accelerate smoothly. This will give you the best fuel economy and effective emissions control. The following shift points are recommended: Engine Speed Limiter If you exceed the maximum speed for the gear you are in, the engine speed will enter into the tachometer's red zone. If this occurs, you may feel the engine cut in and out.
Main Menu Table of Contents Automatic Transmission Your Acura's transmission has four forward speeds, and is electronically controlled for smoother shifting. It also has a "lock-up" torque converter for better fuel economy. You may feel what seems like another shift when the converter locks. Shift Lever Position Indicator Shift Lever Positions SHIFT LEVER This indicator on the instrument panel shows which position the shift lever is in.
Main Menu Table of Contents Automatic Transmission Reverse (R) — To shift to Reverse from Park, see the explanation under Park. To shift to Reverse from Neutral, come to a complete stop and then shift. Press the release button before shifting into Reverse from Neutral. Park (P) — This position mechanically locks the transmission. Use Park whenever you are turning off or starting the engine. To shift out of Park, you must press on the brake pedal and have your foot off the accelerator pedal.
Main Menu Table of Contents Automatic Transmission Drive (D3) —This position is similar to D4, except only the first three gears are selected. Use D3 when towing a trailer in hilly terrain, or to provide engine braking when going down a steep hill. D3 can also keep the transmission from cycling between third and fourth gears in stop-and-go driving. For faster acceleration when in D3 or D4, you can get the transmission to automatically downshift by pushing the accelerator pedal to the floor.
Main Menu Table of Contents Automatic Transmission Shift Lock Release This allows you to move the shift lever out of Park if the normal method of pushing on the brake pedal and pressing the release button does not work. RELEASE BUTTON 1. Set the Parking brake. 2. Remove the key from the ignition switch. 3. Put a cloth on the edge of the Shift Lock Release slot cover next to the shift lever.
Main Menu Table of Contents Parking Always use the parking brake when you park your car. The indicator on the instrument panel shows that the parking brake is not fully released; it does not indicate that the parking brake is firmly set. Make sure the parking brake is set firmly or your car may roll if it is parked on an incline. If the car is facing uphill, turn the front wheels away from the curb. If you have a manual transmission, put it in first gear.
Main Menu Table of Contents The Braking System Your Acura is equipped with disc brakes at all four wheels. A power assist helps reduce the effort needed on the brake pedal. Put your foot on the brake pedal only when you intend to brake. Resting your foot on the pedal keeps the brakes applied lightly, causing them to build up heat. Heat build-up can reduce how well your brakes work. It also keeps your brake lights on all the time, confusing drivers behind you.
Main Menu Table of Contents The Braking System Brake System Design The hydraulic system that operates the brakes has two separate circuits. Each circuit works diagonally across the vehicle (the left-front brake is connected with the right-rear brake, etc.). If one circuit should develop a problem, you will still have braking at two wheels. Front Anti-lock Brakes The Integra LS, GS, GS-R and Type-R models have an Anti-lock Brake System (ABS) as standard equipment.
Main Menu Table of Contents The Braking System You should never pump the brake pedal, this defeats the purpose of the ABS. Let the ABS work for you by always keeping firm, steady pressure on the brake pedal as you steer away from the hazard. This is sometimes referred to as "stomp and steer." Important Safety Reminders ABS does not reduce the time or distance it takes to stop the car, it only helps with steering control during braking.
Main Menu Table of Contents The Braking System, Limited Slip Differential ABS Indicator ABS INDICATOR* * U.S. indicator shown The ABS is self-checking. If anything goes wrong, the ABS indicator on the instrument panel comes on (see page 55). This means the anti-lock function of the braking system has shut down. The brakes still work like a conventional system without antilock, providing normal stopping ability. You should have the dealer inspect your car as soon as possible.
Main Menu Table of Contents Driving in Bad Weather Rain, fog, and snow conditions require a different driving technique because of reduced traction and visibility. Keep your car wellmaintained and exercise greater caution when you need to drive in bad weather. The cruise control should not be used in these conditions. Driving Technique — Always drive slower than you would in dry weather. It takes your car longer to react, even in conditions that may seem just barely damp.
Main Menu Table of Contents Driving in Bad Weather Traction — Check your tires frequently for wear and proper pressure. Both are important in preventing "hydroplaning" (loss of traction on a wet surface). In the winter, mount snow tires on all four wheels for the best handling. Watch road conditions carefully, they can change from moment to moment. Wet leaves can be as slippery as ice. "Clear" roads can have patches of ice.
０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ Main Menu Table of Contents Towing a Trailer Your Acura has been designed primarily to carry passengers and their cargo. You can use it to tow a trailer if you carefully observe the load limits, use the proper equipment, and follow the guidelines in this section. On Type-R model Your vehicle is not designed to tow a trailer. Attempting to do so can void your warranties.
Main Menu Table of Contents Towing a Trailer Checking Loads The best way to confirm that vehicle and trailer weights are within limits is to have them checked at a public scale. Using a suitable scale or a special tongue load gauge, check the tongue load the first time you set up a towing combination (a fully-loaded vehicle and trailer), then recheck the tongue load whenever the conditions change. Safety Chain Always use a safety chain.
Main Menu Table of Contents Towing a Trailer Trailer Brakes Acura recommends that any trailer having a total weight of 1,000 Ibs (450 kg) or more be equipped with its own electric or surge-type brakes. If you choose electric brakes, be sure they are electronically actuated. Do not attempt to tap into your vehicle's hydraulic system. No matter how successful it may seem, any attempt to attach trailer brakes to your vehicle's hydraulic system will lower braking effectiveness and create a potential hazard.
Main Menu Table of Contents Towing a Trailer Additional Trailer Equipment Many states and provinces require special outside mirrors when towing a trailer. Even if they don't, you should install special mirrors if you cannot clearly see behind you, or if the trailer creates a blind spot. Ask your trailer sales or rental agency if any other items are recommended or required for your towing situation.
Main Menu Table of Contents Towing a Trailer Driving Safely With a Trailer The added weight, length, and height of a trailer will affect your vehicle's handling and performance, so driving with a trailer requires some special driving skills and techniques. For your safety and the safety of others, take time to practice driving maneuvers before heading for the open road, and follow the guidelines discussed below.
Main Menu Table of Contents Towing a Trailer Handling Crosswinds and Buffeting Parking Crosswinds and air turbulence caused by passing trucks can disrupt your steering and cause trailer swaying. When being passed by a large vehicle, keep a constant speed and steer straight ahead. Do not try to make quick steering or braking corrections. Follow all normal precautions when parking, including firmly setting the parking brake and putting the transmission in Park (automatic) or in 1 st or Reverse (manual).
Main Menu Maintenance This section explains why it is important to keep your car well maintained and to follow basic maintenance safety precautions. This section also includes Maintenance Schedules for normal driving and severe driving conditions, a Maintenance Record, and instructions for simple maintenance tasks you may want to take care of yourself. If you have the skills and tools to perform more complex maintenance tasks on your Acura, you may want to purchase the Service Manual.
Main Menu Table of Contents Maintenance Safety Regularly maintaining your car is the best way to protect your investment. Proper maintenance is essential to ３／０７／１０ １６：１１：０９ your safety and the safety３１Ｓ５Ａ９３０ of your passengers. It will also reward you with more economical, trouble-free driving and help reduce air pollution. Improperly maintaining this car or failing to correct a problem before driving can cause a crash in which you can be seriously hurt or killed.
Main Menu Table of Contents Maintenance Safety Important Safety Precautions Before you begin any maintenance, make sure your car is parked on level ground and that the parking brake is set. Also, be sure the engine is off. This will help to eliminate several potential hazards: Carbon monoxide poisoning from engine exhaust. Be sure there is adequate ventilation whenever you operate the engine. Burns from hot parts. Let the engine and exhaust system cool before touching any parts. Injury from moving parts.
Main Menu Table of Contents Maintenance Schedule The Maintenance Schedule specifies how often you should have your car serviced and what things need attention. It is essential that you have your car serviced as scheduled to retain its high level of safety, dependability, and emissions control performance. The services and time or distance intervals shown in the maintenance schedule assume you will use your car as normal transportation for passengers and their possessions.
Main Menu Table of Contents Maintenance Schedule Your authorized Acura dealer knows your car best and can provide competent, efficient service. However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or person who is skilled in this type of automotive service. Keep all the receipts as proof of completion, and have the person who does the work fill out the Maintenance Record. Check your warranty booklet for more information.
Main Menu Table of Contents U.S. Owners Follow the Normal Conditions Maintenance Schedule if the severe driving conditions specified in the Severe Conditions Maintenance Schedule do not apply. NOTE: If you only OCCASIONALLY drive under a "severe" condition, you should follow the Normal Conditions Maintenance Schedule. Canadian Owners Follow the Maintenance Schedule for Severe Conditions. # : See information on maintenance and emissions warranty, last column, page 161.
Main Menu Table of Contents Service at the indicated distance or time, whichever comes first. Do the items in A, B, C as required for each distance/time interval. Follow this schedule if the severe driving conditions described in the Severe Conditions Schedule on the next page do not apply. Canadian owners: Follow the schedule for Severe Conditions. page 199 # : See information on maintenance and emissions warranty, last column, page 161 .
Main Menu Table of Contents U.S. Owners Follow the Severe Conditions Maintenance Schedule if you drive your vehicle MAINLY under one or more of the following conditions: Driving less than 5 miles (8 km) per trip or, in freezing temperatures, driving less than 10 miles (16 km) per trip. Driving in extremely hot [over 90° F (32° C)] conditions. Extensive idling or long periods of stop-and-go driving. Trailer towing, driving with a roof top carrier, or driving in mountainous conditions.
Main Menu Table of Contents Use this schedule if your vehicle is MAINLY driven in any of the following Severe Conditions, or normally driven in Canada; otherwise use the Normal Schedule. Service at the indicated distance or time, whichever comes first. Do the items in A, B, C, D as required for each distance/time. Severe Conditions: Driving less than 5 miles (8 km) per trip or, in freezing temperatures, driving less than 10 miles (16 km) per trip. Driving in extremely hot (over 90°F/32°C) conditions.
Main Menu Table of Contents *: See Timing Belt on page 195 to determine need for replacement. NOTE: Check engine oil and coolant at each fuel stop.
Main Menu Table of Contents Required Maintenance Record (for Normal and Severe Schedules) You or the servicing dealer can record all completed maintenance here, whether you follow the schedule for normal conditions (page 162 ) or severe conditions (page 164). Keep the receipts for all work done on your vehicle.
Main Menu Table of Contents Required Maintenance Record (for Normal and Severe Schedules) Maintenance
Main Menu Table of Contents Owner Maintenance Checks You should check the following items at the specified intervals. If you are unsure of how to perform any check, turn to the page given. Engine oil level — Check every time you fill the fuel tank. See page 127. Engine coolant level — Check the radiator reserve tank every time you fill the fuel tank. See page 128. Windshield washer fluid — Check the level in the reservoir monthly.
Main Menu Table of Contents Fluid Locations BRAKE FLUID (Gray cap) AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop) COOLANT RESERVOIR (5-speed Manual Transmission only) CLUTCH FLUID (Gray cap) ENGINE OIL FILL-CAP (Blackcap) WASHER FLUID (Blue cap) POWER STEERING FLUID (Red cap) RADIATOR CAP ENGINE OIL DIPSTICK (Orange loop) Maintenance
Main Menu Table of Contents Engine Oil Adding Oil ENGINE OIL FILL CAP Recommended Oil Oil is a major contributor to your engine's performance and longevity. Always use a premium-grade detergent oil. It is highly recommended that you use Genuine Honda Motor oil in your vehicle for as long as you own it. The API Service label also tells you the service classification of the oil. Always use an oil that is labeled "API Service SJ." This service rating may include other classifications, such as CD.
Main Menu Table of Contents Engine Oil The oil container may also display the API Certification seal. Make sure it says "For Gasoline Engines." API CERTIFICATION SEAL Maintenance The SAE numbers tell you the oil's viscosity or weight. Select the oil for your car according to this chart. Ambient Temperature An oil with a viscosity of 5W-30 is preferred for improved fuel economy and year-round protection in your Acura.
Main Menu Table of Contents Engine Oil Synthetic Oil You may use a synthetic motor oil if it meets the same requirements given for conventional motor oil: energy conserving, a service classification of SJ, and the proper weight as shown on the chart. When using synthetic oil, you must follow the oil and filter change intervals given in the maintenance schedule. Additives Your Acura does not need any oil additives.
Main Menu Table of Contents Engine Oil 1. Run the engine until it reaches normal operating temperature, then shut it off. OIL FILTER OIL DRAIN BOLT WASHER 2. Open the hood and remove the engine oil fill cap. Remove the oil drain bolt and washer from the bottom of the engine. Drain the oil into an appropriate container. 3. Remove the oil filter and let the remaining oil drain. A special wrench (available from your Acura dealer) is required to remove the filter. 4.
Main Menu Table of Contents Engine Oil 5. Put a new washer on the drain bolt, then reinstall the drain bolt. Tighten it to: 33 Ibf.ft (44 N.m , 4.5 kgf.m) 6. Refill the engine with the recommended oil. Engine oil change capacity (including filter): (SE, LS, GS) 4.0 US qt (3.8 , 3.3 Imp qt) (GS-R,Type-R) 4.2 US qt (4.0 , 3.5 Imp qt) 7. Replace the engine oil fill cap. Start the engine. The oil pressure indicator light should go out within five seconds.
Main Menu Table of Contents Cooling System ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ０ Adding Engine Coolant RESERVE TANK MIN MAX If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to the MAX line. Inspect the cooling system for leaks. This coolant should always be a mixture of 50 percent antifreeze and 50 percent water. Never add straight antifreeze or plain water. Maintenance Always use Genuine Honda Antifreeze/Coolant.
Main Menu Table of Contents Cooling System 1. Make sure the engine and radiator are cool. RADIATOR CAP 2. Turn the radiator cap counterclockwise, without pressing down on it, until it stops. This relieves any pressure remaining in the cooling system. 3. Remove the radiator cap by pushing down and turning counterclockwise. RESERVE TANK 4. The coolant level should be up to the base of the filler neck. Add coolant if it is low. 6. Pour coolant into the reserve tank.
Main Menu Table of Contents Cooling System Do not add any rust inhibitors or other additives to your car's cooling system. They may not be compatible with the coolant or engine components. Replacing Engine Coolant The cooling system should be completely drained and refilled with new coolant according to the time and distance recommendations in the maintenance schedule. Only use Genuine Honda Antifreeze/Coolant. Draining the coolant requires access to the underside of the car.
Main Menu Table of Contents Cooling System 6. When the coolant stops draining, tighten the drain plug at the bottom of the radiator. Put a new washer on the drain bolt, then reinstall the drain bolt in the engine block. Tighten it securely. RESERVE TANK FILLER NECK Tightening torque: 58 Ibf.ft (78 N.m , 8.0 kgf.m) HOLDER RESERVE TANK CAP 5. Remove the reserve tank from its holder by pulling it straight up. Drain the coolant, then put the tank back in its holder. 7.
Main Menu Table of Contents Cooling System 10.Fill the radiator with coolant up to the base of the filler neck. 11.Fill the reserve tank to the MAX mark. Install the reserve tank cap. 15.Start the engine and hold it at 1,500 rpm until the radiator fan comes on. Turn off the engine. Check the coolant level in the radiator and add coolant if needed. 12.Install the radiator cap, and tighten it to the first stop. 16.Install the radiator cap, and tighten it fully. 13.
Main Menu Table of Contents Windshield Washers Check the level in the windshield washer reservoir at least monthly during normal usage. In bad weather, when you use the washers often, check the level every time you stop for fuel. This reservoir supplies the windshield and rear window washers. WINDSHIELD WASHER RESERVOIR When you refill the reservoir, clean the edges of the windshield wiper blades with windshield washer fluid on a clean cloth. This will help to condition the blade edges.
Main Menu Table of Contents Transmission Fluid Automatic Transmission DIPSTICK UPPER MARK LOWER MARK Check the fluid level with the engine at normal operating temperature. 1. Park the car on level ground. Shut off the engine. 2. Remove the dipstick (yellow loop) from the transmission and wipe it with a clean cloth. Maintenance 5. If the level is below the lower mark, add fluid into the filler hole to bring it to the upper mark. Always use Honda Premium Formula Automatic Transmission Fluid (ATF).
Main Menu Table of Contents Transmission Fluid, Brake and Clutch Fluid 5-speed Manual Transmission Correct level FILLER BOLT Check the fluid level with the transmission at normal operating temperature and the car sitting on level ground. Remove the transmission filler bolt and carefully feel inside the bolt hole with your finger. The fluid level should be up to the edge of the bolt hole. If it is not, add Genuine Honda Manual Transmission Fluid (MTF) until it starts to run out of the hole.
Main Menu Table of Contents Brake and Clutch Fluid Always use Genuine Honda DOT 3 brake fluid. If it is not available, you should use only DOT 3 or DOT 4 fluid, from a sealed container, as a temporary replacement. However, the use of any non-Honda brake fluid can cause corrosion and decrease the life of the system. Have the brake system flushed and refilled with Honda DOT 3 brake fluid as soon as possible.
Main Menu Table of Contents Power Steering UPPER LEVEL Always use Genuine Honda Power Steering Fluid. If it is not available, you may use another power steering fluid as an emergency replacement. However, continued use can cause increased wear and poor steering in cold weather. Have the power steering system flushed and refilled with Honda PSF as soon as possible. A low power steering fluid level can indicate a leak in the system.
Main Menu Table of Contents Air Cleaner Element The air cleaner element should be cleaned or replaced according to the time and distance recommendations in the maintenance schedule. BOLTS Cleaning (Severe Conditions) Clean the air cleaner element by blowing compressed air through it in the opposite direction to normal air flow. If you do not have access to compressed air (such as a service station), ask your Acura dealer to do this service.
Main Menu Table of Contents Hood Latch, Spark Plugs Hood Latch LATCH ASSEMBLY Clean the hood latch assembly with a mild cleaner, then lubricate it with a multipurpose grease. Lubricate all the moving parts, including the pivot. Follow the time and distance recommendations in the Maintenance Schedule. If you are not sure how to clean and grease the latch, contact your Acura dealer. Spark Plugs The spark plugs in your car are a special platinum-tipped design for longer life.
Main Menu Table of Contents Spark Plugs NOTICE Tighten the spark plugs carefully. A spark plug that is too loose can overheat and damage the engine. Overtightening can cause damage to the threads in the cylinder head. 7. Install the spark plug cap. 8. Repeat this procedure for the other three spark plugs. 4. Remove the spark plug with a five-eighths inch (16 mm) spark plug socket. 5. Put the new spark plug into the socket; then screw it into the hole. Screw it in by hand so you do not crossthread it.
Main Menu Table of Contents Spark Plugs, Battery Specifications: (SE, LS, GS) NGK: PZFR5F-11 DENSO: PKJ16CR-L11 Plug Gap: 0.04 in (1.1 m m (GS-R) NGK: DENSO: Battery Check the condition of your car's battery monthly. You should check the color of the test indicator window, and for corrosion on the terminals. TEST INDICATOR WINDOW ) PFR6G-13 PK20PR-L13 Plug Gap: 0.05 in (1.3 mm ) CType-R) NGK: PFR6G-11 DENSO: PK20PR-L11 Plug Gap: 0.04 in (1.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ Battery If the terminals are severely corroded, clean them with baking soda and water. Then use a wrench to loosen and remove the cables from the terminals. Always disconnect the negative (—) cable first and reconnect it last. Clean the battery terminals with a terminal cleaning tool or wire brush. Reconnect and tighten the cables, then coat the terminals with grease. Check the battery terminals for corrosion (a white or yellowish powder).
Main Menu Table of Contents Battery If your car's battery is disconnected or goes dead, the audio system will disable itself. The next time you turn on the radio you will see "Code" in the frequency display. Use the Preset buttons to enter the five-digit code (see page 119). NOTICE Charging the battery with the cables connected can seriously damage your car's electronic controls. Detach the battery cables before connecting the battery to a charger.
Main Menu Table of Contents Wiper Blades Check the condition of the wiper blades at least every six months. Look for signs of cracking in the rubber, or areas that are getting hard. Replace the blades if you find these signs, or they leave streaks and unwiped areas when used. WIPER ARMS LOCK TAB To replace the blade: 1. Raise the wiper arm off the windshield. Maintenance 2. Disconnect the blade assembly from the wiper arm by pushing in the lock tab.
Main Menu Table of Contents Wiper Blades BLADE BLADE 5. Slide the new wiper blade into the holder until the tabs lock. 6. Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place. 7. Lower the wiper arm down against the windshield. REINFORCEMENT 3. Remove the blade from its holder by grasping the tabbed end of the blade. Pull firmly until the tabs come out of the holder. 4. Examine the new wiper blades.
Main Menu Table of Contents Air Conditioning System Optional for Type-R model Your car's air conditioning is a sealed system. Any major maintenance, such as recharging, should be done by a qualified mechanic. You can do a couple of things to make sure the air conditioning works efficiently. AIR CONDITIONING CONDENSER Periodically check the engine's radiator and air conditioning condenser for leaves, insects, and dirt stuck to the front surface. These block the air flow and reduce cooling efficiency.
Main Menu Table of Contents Drive Belts, Timing Belt Drive Belts The belts should have the following "play" or deflection. Alternator belt: 0.35 — 0.43 in (9.0 — 11.0 mm) Power steering belt: 0.45 — 0.53 in (11.5 — 13.5 mm) Compressor belt (On cars with A/C): 0.30 — 0.37 in (7.5 — 9.5 mm) ALTERNATOR BELT COMPRESSOR BELT POWER STEERING BELT If you see signs of wear or looseness, have your dealer adjust or replace the belts.
Main Menu Table of Contents Tires Inflation To safely operate your car, your tires Keeping the tires properly inflated must be the proper type and size, in provides the best combination of good condition with adequate tread, handling, tread life and riding and correctly inflated. The following pages give more detailed information comfort.
Main Menu Table of Contents Tires Inspection Every time you check inflation, you should also examine the tires for damage, foreign objects, and wear. Recommended Tire Pressures for Normal Driving The following chart shows the recommended cold tire pressures for most normal driving conditions and speeds. Tire pressures for high speed driving are the same as for normal driving. You should look for: Bumps or bulges in the tread or side of the tire. Replace the tire if you find either of these conditions.
Main Menu Table of Contents Tires INDICATOR LOCATION MARKS TREAD WEAR INDICATORS Your car's tires have wear indicators molded into the tread. When the tread wears down to that point, you will see a 1/2 inch (12.7 mm) wide band running across the tread. This shows there is less than 1/16 inch (1.6 mm) of tread left on the tire. A tire that is this worn gives very little traction on wet roads. You should replace the tire if you can see the tread wear indicator in three or more places around the tire.
Main Menu Table of Contents Tires Tire Rotation Front Front (For Non-directional (For Directional Tires and Wheels) Tires and Wheels) To help increase tire life and distribute wear more evenly, you should have the tires rotated every 7,500 miles (12,000 km). Move the tires to the positions shown in the chart each time they are rotated. When shopping for replacement tires, you may find that some tires are "directional." This means they are designed to rotate only in one direction.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Tires Replacing Tires and Wheels The tires that came with your car were selected to match the performance capabilities of the car while providing the best combination of handling, ride comfort, and long life. You should replace them with radial tires of the same size, load range, speed rating, and maximum cold tire pressure rating (as shown on the tire's sidewall).
Main Menu Table of Contents Tires Wheels and Tires Wheels: (SE) 14 x 5 1/2 JJ (LS, GS, GS-R, Type-R) 15x6 JJ Tires: (SE) P195/60R14 85H (LS, GS, GS-R) P195/55R15 84V (Type-R) 195/55R15 84V See page 252 for information about DOT Tire Quality Grading. Winter Driving SE, LS, GS and GS-R models Tires that are marked " M + S " or "All Season" on the sidewall have an all-weather tread design. They should be suitable for most winter driving conditions.
Main Menu Table of Contents Tires Snow Tires Tire Chains All Models SE, LS, GS and GS-R models If you mount snow tires on your Acura, make sure they are radial tires of the same size and load range as the original tires. Mount snow tires on all four wheels to balance your car's handling in all weather conditions. Keep in mind the traction provided by snow tires on dry roads may not be as high as your car's original equipment tires. You should drive cautiously even when the roads are clear.
Main Menu Table of Contents Lights Check the operation of your car's exterior lights at least once a month. A burned out bulb can create an unsafe condition by reducing your car's visibility and the ability to signal your intentions to other drivers.
Main Menu Table of Contents Lights BACK-UP LIGHT TURN SIGNAL SIDE MARKER LIGHT Check the following: Headlights (low and high beam) Parking lights Taillights Brake lights High-mount brake light Turn signals Back-up lights Hazard light function License plate light Side marker lights Daytime running lights (Canadian models) If you find any bulbs are burned out, replace them as soon as possible. Refer to the chart on page 251 to determine what type of replacement bulb is needed.
Main Menu Table of Contents Lights Headlight Aiming The headlights were properly aimed when your car was new. You should check their aim if you regularly carry heavy items in the cargo area or pull a trailer. Each headlight assembly has horizontal and vertical adjustment indicators. These are set to their "0" positions after the headlights are aimed at the factory. To check these settings: HORIZONTAL ANGLE GAUGE 1. Make sure the fuel tank is full. Park the car on level ground. 2.
Main Menu Table of Contents Lights VERTICAL ANGLE GAUGE 5. Check the vertical angle gauge. The bubble should be centered underneath the longest scribe mark on the gauge. Maintenance HORIZONTAL ADJUSTMENT 6. If either indicator is not aligned with its "0" mark as described, an adjustment can be made using a Phillips-head screwdriver to realign it with the "0" mark. Please refer to the illustrations. VERTICAL ADJUSTMENT 7.
Main Menu Table of Contents Lights Replacing a Headlight Bulb Your car has two bulbs on each side, four in total. Make sure you are replacing the bulb that is burned out. Your car uses halogen headlight bulbs. When replacing a bulb, handle it by its plastic case and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth. NOTICE Halogen headlight bulbs get very hot when lit.
Main Menu Table of Contents Lights Replacing Front Turn Signal/ Parking and Side Marker Light Bulbs 5. Install the new bulb in the socket. 6. Insert the socket back into the light assembly. Turn it clockwise to lock it in place. 7. Test the lights to make sure the new bulb is working. 8. Put the light assembly into the bumper. Make sure the tab on the light assembly fits into the bumper slot. Tighten the mounting screw. SCREW 1.
Main Menu Table of Contents Lights Replacing a High-mount Brake Light Bulb LS model 1. Undo the cover fasteners by pushing on the center of each fastener's head until it pops in. Remove the cover. 3. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. 5. Reset each fastener by pushing on the pointed end until it pops back almost flush with the fingers on the housing. 2. Determine which bulb is burned out. 4.
Main Menu Table of Contents Lights Replacing Rear Turn Signal and Side Marker Light Bulbs 3. If the turn signal light bulb is burned out, remove it by pushing it in and turning counterclockwise. If the side marker light bulb is burned out, remove it by pulling it straight out of its socket. Replacing Tail/Stoplight and Back-up Light Bulbs 4. Install the new bulb in the reverse order of removal. 5. Push the socket into the light assembly and turn it clockwise until it locks. 1.
Main Menu Table of Contents Lights 4. Try the tail/stoplights and back-up light to verify which bulb needs replacing. Remove the bulb by turning it counterclockwise. 5. Install the new bulb in the socket. Test it to make sure it works. 6. Reinstall the socket into the light assembly. 2. Undo the seven cover fasteners by pushing on the center of each fastener's head until it pops in. Remove the taillight cover panel. 3. Remove the socket by turning it one-quarter turn counterclockwise. 7.
Main Menu Table of Contents Lights Replacing a Rear License Bulb 4. Turn on the parking lights and check that the new bulb is working. 5. Reinstall the license light assembly. Install the two screws and tighten them securely. 8. Reset each fastener by pushing on the pointed end until it pops back almost flush with the fingers on the housing. 9. Reinstall the cover. Secure each fastener by pushing on the center until it locks (the center is flush with the head). Maintenance 1.
Main Menu Table of Contents Lights Replacing Ceiling, Spot and Cargo Area Light Bulbs The ceiling, spot and cargo area lights come apart the same way. They do not all use the same bulb. CARGO AREA LIGHT LS, GS and GS-R models SPOTLIGHTS CEILING LIGHT 2. Remove the bulb by pulling it straight out of its metal tabs. 3. Push the new bulb into the metal tabs. Snap the lens back in place. 1. Remove the lens by carefully prying on the edge of the lens with a fingernail file or a small flat-tip screwdriver.
Main Menu Table of Contents Storing Your Car If you need to park your car for an extended period (more than one month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your car back on the road. If possible, store your car indoors. Block the rear wheels. If the car is to be stored for a longer period, it should be supported on jackstands so the tires are off the ground.
Main Menu AppearanceCare Regular cleaning and polishing of your Acura helps to keep it "new" looking. This section gives you hints on how to clean your car and preserve its appearance: the paint, brightwork, wheels and interior. Also included are several things you can do to help prevent corrosion. Exterior Care.................................. 216 Washing...................................... 216 Power Antenna Cleaning.......... 216 Waxing........................................ 217 Aluminum Wheels.....
Main Menu Table of Contents Exterior Care Washing Frequent washing helps preserve your car's beauty. Dirt and grit can scratch the paint, while tree sap and bird droppings can permanently ruin the finish. Wash your car in a shady area, not in direct sunlight. If the car is parked in the sun, move it into the shade and let the exterior cool down before you start. Only use the solvents and cleaners recommended in this Owner's Manual.
Main Menu Table of Contents Exterior Care Waxing Always wash and dry the whole car before waxing it. You should wax your car, including the metal trim, whenever water sits on the surface in large patches. It should form into beads or droplets after waxing. You should use a quality liquid or paste wax. Apply it according to the instructions on the container. In general, there are two types of products: Waxes — A wax coats the finish and protects it from damage by exposure to sunlight, air pollution, etc.
Main Menu Table of Contents Interior Care Carpeting Vacuum the carpeting frequently to remove dirt. Ground-in dirt will make the carpet wear out faster. Periodically shampoo the carpet to keep it looking new. Use one of the foam-type carpet cleaners on the market. Follow the instructions that come with the cleaner, applying it with a sponge or soft brush. Keep the carpeting as dry as possible by not adding water to the foam. Fabric Vacuum dirt and dust out of the material frequently.
Main Menu Table of Contents Interior Care Dirt build-up in the loops of the seat belt anchors can cause the belts to retract slowly. Wipe the insides of the loops with a clean cloth dampened in mild soap and warm water or isopropyl alcohol. Windows Clean the windows, inside and out, with a commercially-available glass cleaner. You can also use a mixture of one part white vinegar to ten parts water. This will remove the haze that builds up on the inside of the windows.
Main Menu Table of Contents Corrosion Protection Two factors normally contribute to causing corrosion in your car: 1. Moisture trapped in body cavities. Dirt and road salt that collects in hollows on the underside of the car stays damp, promoting corrosion in that area. 2. Removal of paint and protective coatings from the exterior and underside of the car. Many corrosion-preventive measures are built into your Acura.
Main Menu Table of Contents Body Repairs Body repairs can affect your car's resistance to corrosion. If your car needs repairs after a collision, pay close attention to the parts used in the repair and the quality of the work. Make sure the repair facility uses Genuine Acura replacement body parts. Some companies make sheet metal pieces that seem to duplicate the original Acura body parts, but are actually inferior in fit, finish, and corrosion resistance.
Main Menu 222
Main Menu Taking Care of the Unexpected This section covers the morecommon problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your car towed. Compact Spare Tire....................... 224 Changing a Flat Tire..................... 225 If Your Engine Won't Start.....
Main Menu Table of Contents Compact Spare Tire Your car has a compact spare tire that takes up less space. Use this spare tire as a temporary replacement only. Get your regular tire repaired or replaced and put back on your car as soon as you can. Check the inflation pressure of the compact spare tire every time you check the other tires. It should be inflated to: 60 psi (420 kPa , 4.
Main Menu Table of Contents Changing a Flat Tire If you have a flat tire while driving, stop in a safe place to change it. Stopping in traffic or on the shoulder ３／０７／１０ ３１Ｓ５Ａ９３０ of a busy１６：１１：０９ road is dangerous. Drive slowly along the shoulder until you get to an exit or an area to stop that is far away from the traffic lanes. JACK 3. Open the hatch. Pull up the floor mat and remove the spare tire cover. ００２１ 4. Take the tool kit out of the spare tire well. 5.
Main Menu Table of Contents Changing a Flat Tire JACKING POINT JACK 6. Turn the jack's end bracket counterclockwise to loosen it, then remove the jack. 7. (Except Type-R) Loosen the four wheel nuts 1/2 turn with the wheel wrench. (Type-R) Loosen the five wheel nuts 1/2 turn with the wheel wrench. Taking Care of the Unexpected 8. Find the jacking point nearest the wheel you are removing. Place the jack under the jacking point.
Main Menu Table of Contents Changing a Flat Tire EXTENSION WHEEL WRENCH 9. Use the extension and wheel wrench as shown to raise the vehicle until the flat tire is off the ground. 10.Remove the wheel nuts and flat tire. Temporarily place the flat tire on the ground with the outside surface of the wheel facing up. You could scratch the wheel if you put it face down. BRAKE HUB 11.Before mounting the spare tire, wipe any dirt off the mounting surface of the wheel and hub with a clean cloth.
Main Menu Table of Contents Changing a Flat Tire (Except Type-R) (Type-R) 12.Put on the spare tire. Put the wheel nuts back on finger-tight, then tighten them in a crisscross pattern with the wheel wrench until the wheel is firmly against the hub. Do not try to tighten them fully. Taking Care of the Unexpected 13.Lower the car to the ground and remove the jack. 14.Tighten the wheel nuts securely in the same crisscross pattern.
Main Menu Table of Contents Changing a Flat Tire, If Your Engine Won't Start WING BOLT 17.Secure the flat tire by screwing If Your Engine Won't Start the wing bolt back into its hole. Diagnosing why your engine won't SPACER CONE０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ start falls into two areas, depending 18.Store the jack in its holder with the end bracket facing to the right. Turn the jack's end bracket to lock it in place. Store the tool kit.
Main Menu Table of Contents If Your Engine Won't Start Nothing Happens or the Starter Motor Operates Very Slowly When you turn the ignition switch to START (III), you do not hear the normal noise of the engine trying to start. You may hear a clicking sound or series of clicks, or nothing at all. Check these things: Your car has the Immobilizer System. You should use a properly-coded master or valet key to start the engine (see page 72 ).
Main Menu Table of Contents If Your Engine Won't Start, Jump Starting To jump start your car, follow these Jump Starting The Starter Operates Normally If your car's battery has run down, directions closely: In this case, the starter motor's ０３／０７／１０ ３１Ｓ５Ａ９３０ ００２１ you may１６：１１：０９ be able to start the engine speed sounds normal, or even faster by using a booster battery. Although 1.
Main Menu Table of Contents Jump Starting BOOSTER BATTERY 3. Connect one jumper cable to the positive ( + ) terminal on the booster battery. Connect the other end to the positive ( + ) terminal on your Acura's battery. 4. Connect the second jumper cable to the negative (—) terminal on the booster battery. Connect the other end to the grounding strap as shown. Do not connect this jumper cable to any other part of the engine. 5.
Main Menu Table of Contents If Your Engine Overheats Your car can overheat for several The pointer of your car's temperareasons, such as lack of coolant or a ture gauge should stay in the midmechanical problem. The only range under most conditions. It may indication may be the temperature go higher if you are driving up a long gauge climbing to or above the red steep hill on a very hot day. If it ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ mark.
Main Menu Table of Contents０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ If Your Engine Overheats 6. Look for any obvious coolant leaks, such as a split radiator hose. Everything is still extremely hot, so use caution. If you find a leak, it must be repaired before you continue driving (see Emergency Towing on page 245). 7. If you don't find an obvious leak, check the coolant level in the radiator reserve tank (see page 124). If the level is below the MIN mark, add coolant to halfway between the MIN and MAX marks. 8.
Main Menu Table of Contents Low Oil Pressure Indicator NOTICE Running the engine with low oil pressure can cause serious mechanical damage almost immediately. Turn off the engine as soon as you can safely get the car stopped. LOW OIL PRESSURE INDICATOR This indicator should light when the ignition switch is ON (II), and go out after the engine starts. It should never come on when the engine is running.
Main Menu Table of Contents Charging System Indicator Immediately turn off all electrical accessories: radio, heater, A/C, rear defogger, cruise control, etc. Try not to use other electrically-operated controls such as the power windows. Keep the engine running and take extra care not to stall it. Starting the engine will discharge the battery rapidly. CHARGING SYSTEM INDICATOR This indicator should come on when the ignition switch is ON (II), and go out after the engine starts.
Main Menu Table of Contents Malfunction Indicator Lamp MALFUNCTION INDICATOR LAMP This indicator comes on for a few seconds when you turn the ignition switch ON (II). If it comes on at any other time, it indicates one of the engine's emissions control systems may have a problem. Even though you may feel no difference in your car's performance, it can reduce your fuel economy and cause your car to put out excessive emissions. Continued operation may cause serious damage.
Main Menu Table of Contents Brake System Indicator BRAKE SYSTEM INDICATOR* *U.S. indicator shown The Brake System indicator light should normally come on only when the parking brake is not fully released. If it comes on at any other time, it indicates a problem with the car's brake system. In most cases, the problem is a low fluid level in the brake fluid reservoir. Press lightly on the brake pedal to see if it feels normal.
Main Menu Table of Contents Closing the Moonroof LS, GS and GS-R Models If the electric motor will not close the moonroof, do the following: ROUND PLUG SOCKET 1. Check the fuse for the moonroof motor (see page 240). If the fuse is blown, replace it with one of the same or lower rating. 2. Try closing the moonroof. If the new fuse blows immediately or the moonroof motor still does not operate, you can close the moonroof manually. 3. Get the moonroof wrench out of the tool kit in the cargo area. 4.
Main Menu Table of Contents Fuses All the electrical circuits in your car have fuses to protect them from a short circuit or overload. These fuses are located in two or three fuse boxes. UNDER-HOOD TAB ABS FUSE BOX INTERIOR The under-hood fuse box is located in the engine compartment next to the battery. To open it, push the tab as shown. The interior fuse box is underneath the dashboard on the driver's side. Remove the fuse box lid by swinging the lid down and pulling it straight out of its hinges.
Main Menu Table of Contents Fuses Checking and Replacing Fuses If something electrical in your car stops working, the first thing you should check for is a blown fuse. Determine from the chart on pages 243 and 244, or the diagram on the fuse box lid, which fuse or fuses control that component. Check those fuses first, but check all the fuses before deciding that a blown fuse is not the cause. Replace any blown fuses and check the component's operation. 1. Turn the ignition switch to LOCK (0).
Main Menu Table of Contents Fuses BLOWN If you replace the blown fuse with a spare fuse that has a lower rating, it might blow out again. This does not indicate anything wrong. Replace the fuse with one of the correct rating as soon as you can. NOTICE 5. Look for a burned wire inside the fuse. If it is burned, replace it with one of the spare fuses of the same rating or lower.
Main Menu Table of Contents Fuses INTERIOR FUSE BOX * : On Canadian models CONTINUED Taking Care of the Unexpected
Main Menu Table of Contents Fuses UNDER-HOOD FUSE BOX ABS FUSE BOX Taking Care of the Unexpected
Main Menu Table of Contents Emergency Towing If your vehicle needs to be towed, call a professional towing service or, if you belong to one, an organization that provides roadside assistance. Never tow your vehicle behind another vehicle with just a rope or chain. It is very dangerous. There are three popular types of professional towing equipment: Flat-bed Equipment — The operator loads your vehicle on the back of a truck. This is the best way of transporting your Acura.
Main Menu Table of Contents Emergency Towing If you decide to tow your vehicle with all four wheels on the ground, make sure you use a properlydesigned and attached tow bar. Prepare the vehicle for towing as described above, and leave the ignition switch in Accessory (I) so the steering wheel does not lock. Make sure the radio and any items plugged into the accessory power socket are turned off so they do not run down the battery.
Main Menu Technical Information The diagrams in this section give you the dimensions and capacities of your Acura, and the locations of the identification numbers. The explanations of several electronic and mechanical systems on your Acura are for the more technically-oriented owner. Identification Numbers................. 248 Specifications................................. 250 DOT Tire Quality Grading (U.S. Cars).............................. 252 Treadwear.................................. 252 Traction..
Main Menu Table of Contents Identification Numbers Your car has several identifying numbers located in various places. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is the 17-digit number your Acura dealer uses to register your car for warranty purposes. It is also necessary for licensing and insuring your car. The easiest place to find the VIN is on a plate fastened to the top of the dashboard. You can see it by looking through the windshield on the driver's side.
Main Menu Table of Contents Identification Numbers The Engine Number is stamped into the engine block. MANUAL TRANSMISSION NUMBER AUTOMATIC TRANSMISSION NUMBER The Transmission Number is on a label on top of the transmission.
Main Menu Table of Contents Specifications *1 : SE, LS, GS, GS-R * 2 : Type-R *1 * 1 : SE, LS, GS * 2 : GS-R, Type-R Technical Information page 189. * 3 : GS-R * 4 : Type-R : Including the coolant in the reserve tank and that remaining in the engine. Reserve tank capacity: 0.16 US gal (0.6 ,0.13 Imp gal) * 2 : SE, LS, GS * 3 : GS-R,Type-R * 4 : Excluding the oil remaining in the engine.
Main Menu Table of Contents Specifications page 243 page 244 *1 * : Type-R *2 : SE, LS, GS, GS-R * : Type-R * 1 : SE : Except high-mount brake light installed in rear spoiler *2 : LS, GS, GS-R * 3 : Type-R Technical Information
Main Menu Table of Contents DOT Tire Quality Grading (U.S. Cars) The tires on your car meet all U.S. Federal Safety Requirements. All tires are also graded for treadwear, traction, and temperature performance according to Department of Transportation (DOT) standards. The following explains these gradings. Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between the tread shoulder and the maximum section width.
Main Menu Table of Contents DOT Tire Quality Grading (U.S. Cars) Temperature The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Main Menu Table of Contents Oxygenated Fuels Some conventional gasolines are being blended with alcohol or an ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards, some areas of the United States and Canada use oxygenated fuels to help reduce emissions. If you use an oxygenated fuel, be sure it is unleaded and meets the minimum octane rating requirement. Before using an oxygenated fuel, try to confirm the fuel's contents.
Main Menu Table of Contents Driving in Foreign Countries If you are planning to take your Acura outside the U.S. or Canada, contact the tourist bureaus in the areas you will be traveling in to find out about the availability of unleaded gasoline with the proper octane rating. If unleaded gasoline is not available, be aware that using leaded gasoline in your Acura will affect performance and fuel mileage, and damage its emissions controls. It will no longer comply with U.S.
Main Menu Table of Contents Emissions Controls The burning of gasoline in your car's engine produces several byproducts. Some of these are carbon monoxide (CO), oxides of nitrogen (NOx) and hydrocarbons (HC). Gasoline evaporating from the tank also produces hydrocarbons. Controlling the production of NOx, CO, and HC is important to the environment. Under certain conditions of sunlight and climate, NOx and HC react to form photochemical "smog.
Main Menu Table of Contents Emissions Controls Onboard Refueling Vapor Recovery The Onboard Refueling Vapor Recovery (ORVR) system captures the fuel vapors during refueling. The vapors are adsorbed in a canister filled with activated carbon. While driving, the fuel vapors are drawn into the engine and burned off. Exhaust Emissions Controls The exhaust emissions controls include three systems: PGM-FI, Ignition Timing Control and Three Way Catalytic Converter.
Main Menu Table of Contents Three Way Catalytic Converter The three way catalytic converter contains precious metals that serve as catalysts, promoting chemical reactions to convert the exhaust gasses without affecting the metals. The catalytic converter is referred to as a three-way catalyst, since it acts on HC, CO, and NOx. A replacement unit must be an original Acura part or its equivalent. The three way catalytic converter must operate at a high temperature for the chemical reactions to take place.
Main Menu Warranty and Customer Relations Customer Relations Information................................. 260 Canada Zone Office Map.............. 261 Warranty Coverages..................... 262 Reporting Safety Defects (U.S. Vehicles)........................... 263 Authorized Manuals......................
Main Menu Table of Contents Customer Relations Information Acura dealership personnel are trained professionals. They should be able to answer all your questions. If you encounter a problem that your dealership does not solve to your satisfaction, please discuss it with the dealership's management. The Service Manager or General Manager can help. Almost all problems are solved in this way.
Main Menu Table of Contents Canada Zone Office Map CUSTOMER RELATIONS RELATIONS AVEC LA CLIENTELE Honda Canada Inc.
Main Menu Table of Contents Warranty Coverages U.S. Owners Your new Acura is covered by these warranties: New Car Limited Warranty — covers your new vehicle, except for the battery, emissions control systems and accessories, against defects in materials and workmanship. Emissions Control Systems Defects Warranty and Emissions Performance Warranty — these two warranties cover your vehicle's emissions control systems. Time, mileage, and coverage are conditional.
Main Menu Table of Contents Reporting Safety Defects (U.S. Vehicles) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Acura Automobile Division, American Honda Motor Co., Inc.
Main Menu Table of Contents This page intentionally left blank 264
Main Menu Table of Contents Authorized Manuals Purchasing Factory Authorized Manuals (U.S. only) The following publications covering the operation and servicing of your vehicle can be obtained from Helm Incorporated, either by filling out the attached form or, for credit card holders, calling the toll-free phone number on the form. For manuals prior to the year shown below, contact Helm Incorporated, P.O. Box 07280, Detroit, Michigan 48207, or call 1-800-782-4356. Valid only for sales within the U.S.
Main Menu Table of Contents Authorized Manuals Service Manual: This manual covers maintenance and recommended procedures for repair to engine and chassis components. It is written for the Journeyman mechanic, but is simple enough for most mechanically-inclined owners to understand. Electrical Troubleshooting Manual: This manual complements the Service Manual by providing in-depth troubleshooting information for each electrical circuit in your vehicle.
Main Menu Index Accessories and Modifications.... 130 Accessories................................. 130 Additional Safety Precaution.... 131 Modifications............................. 131 ACCESSORY (Ignition Key Position)........................................ 74 Adding Automatic Transmission Fluid........................................ 182 Brake Fluid................................. 184 Clutch Fluid................................ 184 Engine Coolant........................... 176 Engine Oil............
Main Menu Index Brakes Anti-lock System (ABS)............ 146 Break-in, New Linings.............. 123 Fluid............................................ 183 Light, Burned-out...................... 210 Parking.......................................... 87 System Indicator.................. 54, 238 Wear Indicators......................... 145 Brakes, ABS Operation.................................... 146 System Indicator.................. 55, 148 Braking System..............................
Main Menu Index Clock, Setting the............................ 88 Clutch Fluid.................................... 183 Code, Audio System...................... 119 CO in the Exhaust......................... 256 Cold Weather, Starting in............. 137 Compact Spare............................... 224 Console Compartment.................... 90 Consumer Information*................ 260 Controls, Instruments and............. 51 Coolant Adding......................................... 176 Checking.............
Main Menu Index Engine Coolant Temperature Gauge..... 59 Drive Belts.................................. 195 Malfunction Indicator Lamp................................ 54, 237 Oil Pressure Indicator........ 54, 235 Oil, What Kind to Use............... 171 Overheating................................ 233 Specifications............................. 250 Engine Speed Limiter........... 139, 142 Ethanol in Gasoline ....................... 254 Evaporative Emissions Controls.. 256 Exhaust Fumes......................
Main Menu Index Hydroplaning.................................. 150 Halogen Headlight Bulbs.............. 207 Hatch................................................. 76 Opening the................................. 76 Open Monitor Light.................... 56 Hazard Warning Flashers.............. 65 Headlights Aiming......................................... 205 Daytime Running Lights............. 62 High Beam Indicator................... 57 High Beams, Turning on............ 62 Low Beams, Turning on..........
Main Menu Index Locks Anti-theft Steering Column........ 74 Fuel Fill Door............................. 124 Glove Box..................................... 78 Hatch............................................. 76 Power Door and Hatch............... 75 Low Coolant Level......................... 128 Lower Gear, Downshifting to a.... 138 Low Fuel Indicator.......................... 54 Low Oil Pressure Indicator.... 54, 235 Lubricant Specifications Chart................................... 250, 251 Luggage......
Main Menu Index Windows....................................... 84 Pre-Drive Safety Checklist............. 11 Pregnancy, Using Seat Belts.......... 19 Protecting Adults............................. 12 Additional Safety Precautions.... 19 Advice for Pregnant Women...... 19 Protecting Children......................... 21 Protecting Infants........................ 29 Protecting Larger Children........ 37 Protecting Small Children.......... 33 Using Child Seats with Tethers......................................
Main Menu Index Shifting The Automatic Transmission.. 140 The 5-speed Manual Transmission.......................... 138 Shift Lever Position Indicator...... 140 Shift Lock Release......................... 143 Side Marker Lights, Bulb Replacement in.......................... 208 Signaling Turns................................ 63 Snow Tires...................................... 202 Solvent-type Cleaners.................... 216 Sound System................................. 102 Spare Tire Inflating............
Main Menu Index Winter Driving........................... 201 Tools, Tire Changing.................... 225 Towing A Trailer...................................... 151 Emergency................................. 245 Transmission Checking Fluid Level, Automatic............................... 182 Checking Fluid Level, Manual.................................... 183 Fluid Selection............................ 182 Identification Number............... 249 Shifting the Automatic..............
Main Menu Service Information Summary Gasoline: (SE, LS, GS) Unleaded gasoline, pump octane number of 86 or higher. (GS-R, Type-R) Premium unleaded gasoline, pump octane number of 91 or higher. Fuel Tank Capacity: 13.2 US gal (50 l ,11.0 Imp gal) Recommended Engine Oil: API Service SJ "Energy Conserving" oil, SAE 5W-30 viscosity (see page 171). Oil change capacity (including filter): (SE, LS, GS) 4.0 US qt (3.8 l ,3.3 Imp qt) (GS-R, Type-R) 4.2 US qt (4.0 l ,3.
