2000 NSX Online Reference Owner's Manual Use these links (and links throughout this manual) to navigate through this reference. For a printed owner's manual, click on authorized manuals or go to www.helminc.com. Contents Owner's Identification Form Introduction ................................................................................................................................................... i A Few Words About Safety ........................................................................
Main Menu Owner's Identification OWNER This Owner's Manual should be considered a permanent part of the car, and should remain with the car when it is sold. ADDRESS STREET CITY STATE/PROVINCE V. I. N. ZIP CODE / POSTAL CODE DELIVERY DATE (Date sold to original retail purchaser) DEALER NAME ADDRESS DEALER NO.
Main Menu Introduction Congratulations on your selection of the 2000 Acura NSX. We are certain you will be pleased with your purchase of one of the most sophisticated and technologically-advanced sports cars in the world. One of the best ways to enhance the enjoyment of your new Acura is to read this manual. In it, you will learn how to operate its driving controls and convenience items. Afterwards, keep this owner's manual in your car so you can refer to it at any time.
▼ ▲ Main Menu Main Menu A Few Words About Safety A Few Words About Safety Your safety, and the safety of others, isYour verysafety, important. Andsafety operating this and the of others, vehicle is anAnd important is very safely important. operating this responsibility. car safely is an important responsibility.
Main Menu Your Car at a Glance HEADLIGHT SWITCH (P.56) TURN SIGNAL LEVER (P.58) WINDSHIELD WIPER CONTROLS (P.59) HAZARD WARNING SWITCH (P.60) DIGITAL CLOCK (P.83) HOOD RELEASE HANDLE (P.133) DOOR LOCK SWITCH (P.69) AUTOMATIC CLIMATE CONTROL (P.90) POWER WINDOW SWITCHES (P.73) AUDIO SYSTEM (P.100) MIRROR CONTROLS (P.82) TRUNK RELEASE BUTTON (P.70) FUEL FILL DOOR RELEASE (P.129) SHIFT LOCK RELEASE (P.154) (Automatic transmission only) SEAT ADJUSTMENT SWITCH (P.
Main Menu Your Car at a Glance TCS ON/OFF SWITCH (P.161) INSTRUMENT PANEL BRIGHTNESS (P.57) HAZARD WARNING LIGHT (P.60) HEADLIGHT MOTOR (P.57) HEADLIGHTS (P.56) CRUISE CONTROL MASTER SWITCH (P.60) WINDSHIELD WIPERS/ WASHERS (P.59) REAR WINDOW DEFOGGER (P.57) TURN SIGNALS (P.58) HORN BUTTONS TELESCOPE ADJUSTMENT (P.61) TILT ADJUSTMENT (P.
Main Menu 4
Main Menu Driver and Passenger Safety This section gives you important information about how to protect yourself and your passenger. It shows you how to use seat belts properly. It explains your Supplemental Restraint System. And it tells you how to properly restrain children in your car. Important Safety Precautions .......... 6 Your Car's Safety Features .............. 7 Seat Belts........................................ 8 Airbags............................................ 9 Seats & Seat-Backs.........
Main Menu Table of Contents Important Safety Precautions You'll find many safety recommendations throughout this section, and throughout this manual. The recommendations on this page are the ones we consider to be the most important. Always Wear Your Seat Belt A seat belt is your best protection in all types of collisions. Airbags supplement seat belts, but airbags are designed to inflate only in a moderate to severe frontal collision.
Main Menu Table of Contents Your Car's Safety Features Your car is equipped with many features that work together to protect you and your passenger during a crash. (1) Safety Cage (2) Crush Zones (3) Seats & Seat-Backs (4) Head Restraints (5) Collapsible Steering Column (6) Seat Belts (7) Seat Belt Tensioners (8) Airbags (9) Door Locks Some safety features do not require any action on your part.
Main Menu Table of Contents Your Car's Safety Features ０３／０７／１０ Seat Belts For your safety, and the safety of your passenger, your car is equipped with seat belts in both seating positions. Your seat belt system also includes a light on the instrument panel to remind you and your passenger to fasten your seat belts. Why Wear Seat Belts Seat belts have proven to be the single most effective safety device.
Main Menu Table of Contents Your Car's Safety Features Airbags The most important things you need to know about your airbags are: Airbags do not replace seat belts. The seat belts are the occupants' primary protection in all types of collisions. Airbags supplement seat belts by providing extra protection for occupants' heads and chests.
Main Menu Table of Contents Your Car's Safety Features Seats & Seat-Backs Your car's seats are designed to keep you in a comfortable, upright position so you can take full advantage of the protection offered by seat belts and the energy absorbing materials in the seats. How you adjust your seats and seatbacks can also affect your safety.
Main Menu Table of Contents Your Car's Safety Features Pre-Drive Safety Checklist To make sure you and your passenger get the maximum protection from your car's safety features, check the following each time before you drive away: You and any adult passenger, or a larger child who has outgrown child seats, are wearing your seat belts and wearing them properly (see page 15). A small child riding in a forwardfacing child seat is properly restrained (see page 26).
Main Menu Table of Contents Protecting Adults Introduction The following pages provide instructions on how to properly protect adult occupants. These instructions also apply to a child whom you have decided is large enough and mature enough to ride as a passenger. (See page 29 for important additional guidelines on how to properly protect larger children.) 1. Close and Lock the Doors After everyone has entered the car, be sure the doors are closed and locked.
Main Menu Table of Contents Protecting Adults To reduce the chance of injury, wear your seat belt properly, sit upright with your back against the seat, and move the seat as far back as possible from the steering wheel while still ０３／０７／１０ １６：１１：０９ maintaining full control ３１Ｓ５Ａ９３０ of the car. Also make sure your passenger moves the seat as far to the rear as possible. Sitting too close to an airbag can result in serious injury or death if the airbags inflate.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Protecting Adults Reclining a seat-back so that the shoulder part of the belt no longer rests against the occupant's chest reduces the protective capability of the belt. It also increases the chance of sliding under the belt in a crash and being seriously injured. The farther a seat-back is reclined, the greater the risk of injury. Reclining the seat-back too far can result in serious injury or death in a crash.
Main Menu Table of Contents Protecting Adults ０３／０７／１０ 4. Fasten and Position the Seat Belts Insert the latch plate into the buckle, then tug on the belt to make sure the belt is securely latched. Also check that the belt is not twisted, because a twisted belt can cause serious injuries in a crash. １６：１１：０９ ３１Ｓ５Ａ９３０ spreads the forces of a crash over the strongest bones in your upper body. Improperly positioning the seat belts can cause serious injury or death in a crash.
Main Menu Table of Contents Protecting Adults If a seat belt does not seem to work as it should, it may not protect the occupant in a crash. No one should sit in a seat with an inoperative seat belt. Anyone using a seat belt that is not working properly can be seriously injured or killed. Have your Acura dealer check the belt as soon as possible. See page 35 for additional information about your seat belt system and how to take care of your belts. 5.
Main １６：１１：０９ Menu Table of３１Ｓ５Ａ９３０ Contents ０３／０７／１０ ００２１ Protecting Adults Advice for Pregnant Women Sitting improperly or out of position can result in serious injury or death in a crash. Always sit upright, well back in the seat, with your feet on the floor. Remember, to get the best protection from your car's airbags and other safety features, you must sit properly and wear your seat belt properly.
Main Menu Table of Contents Protecting Adults Additional Safety Precautions Two people should never use the same seat belt. If they do, they could be very seriously injured in a crash. Do not put any accessories on seat belts. Devices intended to improve occupant comfort or reposition the shoulder part of a seat belt can severely compromise the protective capability of the seat belt and increase the chance of serious injury in a crash. Do not place hard or sharp objects between yourself and an airbag.
Main Menu Table of Contents０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Protecting Children Children who are unrestrained or improperly restrained can be seriously injured or killed in a crash. Any child too small for a seat belt should be properly restrained in a child seat. A larger child should be properly restrained with a seat belt. Children depend on adults to protect them. However, despite their best intentions, many parents and other adults may not know how to properly protect young passengers.
Main Menu Table of Contents Protecting Children Your Car is Not Recommended for Child Passengers We strongly recommend that you do not carry any child in this car. One reason is that your car does not have a back seat, and accident statistics show that a child of any size or age is safer when they are properly restrained in the back seat of a vehicle. The Passenger's Airbag Poses Serious Risks to Children Airbags have been designed to help protect adults in a moderate to severe frontal collision.
Main Menu Table of Contents Protecting Children U.S. Models Canadian Models To remind you of the passenger's airbag hazards, your car has warning labels on the dashboard and on the driver's and passenger's visors. Please read and follow the instructions on these labels. To remind you of the airbag hazards, your car has warning labels on the driver's and passenger's visors. Please read and follow the instructions on these labels.
Main Menu Table of Contents Protecting Children Additional Safety Precaution Do not leave a child alone in your car. Leaving a child without adult supervision is illegal in most states and Canadian provinces and can be very hazardous. For example, a small child left in a car on a hot day can die from heatstroke. A child left alone with the key in the ignition can accidentally set the car in motion, possibly injuring themselves or others.
Main Menu Table of Contents Protecting Children 2. The child seat should be of the proper type and size to fit the child. 3. The child seat should fit the passenger's seat. Due to variations in the design of child seats, vehicle seats, and seat belts, all child seats will not fit all seating positions in all cars. Before purchasing a child seat, we recommend that parents test the child seat to make sure it fits properly in the passenger's seat.
Main Menu Table of Contents Protecting Children Placing a Child Seat Passenger's Seat This page briefly summarizes Acura's recommendations on where to place a child seat in your car. Infants: Never in the passenger's seat, due to the passenger's airbag hazard. Airbags Pose Serious Risks to Children The passenger's airbag inflates with enough force to kill or seriously injure an infant in a rear-facing child seat. A small child in a forward-facing child seat is also at risk.
Main Menu Table of Contents Protecting Children After selecting a proper child seat, there are three main steps in installing the seat: To provide security during normal driving maneuvers as well as during a collision, we recommend that parents secure a child seat as firmly as possible. 1. Secure the child seat to the car with a seat belt. All child seats must be secured to the car with the lap part of a lap/shoulder belt.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２ Protecting Children Protecting Small Children If you decide to carry a small child in this car, follow the instructions and guidelines below. Child Seat Type A child who can sit up without support, and who fits within the child seat maker's weight and height limits, should be restrained in a forward-facing, upright child seat. Of the different seats available, we recommend those that have a fivepoint harness system as shown.
Main Menu Table of Contents Protecting Children Child Seat Installation The passenger's seat belt has a locking mechanism that must be activated to secure a child seat. The following pages provide instructions and tips on how to secure a forward-facing child seat with this type of seat belt. 1. Move the vehicle seat to the rearmost position. Moving the seat as far back as possible reduces the chance of a child being injured or killed if the passenger's airbag inflates.
Main Menu Table of Contents Protecting Children Additional Precautions for Small Children Never hold a small child on your lap. If you are not wearing a seat belt in a crash, you could be thrown forward into the dashboard and crush the child. 5. After confirming that the belt is locked, grab the shoulder part of the belt near the buckle and pull up to remove any slack from the lap part of the belt. Remember, if the lap part of the belt is not tight, the child seat will not be secure.
Main Menu Table of Contents Protecting Children Protecting Larger Children If a child is too short for the shoulder part of the belt to properly fit, we The passenger's airbag poses recommend that the child use a serious risks to children, including those who have outgrown child seats. booster seat until they are tall enough to use the seat belt without a If the vehicle seat is too far forward, booster.
Main Menu Table of Contents Protecting Children However, if the belt touches or crosses the child's neck, the child needs to use a booster seat. Do not let a child wear a seat belt across the neck. This could result in serious neck injuries during a crash. Do not let a child put the shoulder part of a seat belt behind the back or under the arm. This could cause very serious injuries during a crash. It also increases the chance that the child will slide under the belt in a crash and be injured.
Main Menu Table of Contents Protecting Children A child may continue using a booster seat until the tops of the ears are even with the top of the seat-back. A child of this height should be tall enough to use the lap/shoulder belt without a booster. When Can a Larger Child Ride in this Car Children vary widely. And while age may be one indicator of when a child can safely ride in this car, there are other important factors you should consider.
Main Menu Table of Contents Protecting Children If you decide that a child can safely ride in this car, be sure to: Carefully read the owner's manual and make sure you understand all seat belt instructions and all safety information. Move the vehicle seat to the rearmost position. Have the child sit up straight, back against the seat, and feet on or near the floor. Check that the child's seat belt is properly positioned and secured. Driver and Passenger Safety Supervise the child.
Main Menu Table of Contents Protecting Children Using Child Seats with Tethers NSX-T 4 in (10 cm) 1 in (2.5 cm) 9.7 in (24.6 cm) Fixed Roof Model Your car has a tether anchorage point on the panel behind the passenger's seat-back for securing a tether-style child seat to the car. Since a tether can provide additional security, we recommend using a tether whenever one is required or available. Pass the strap between the top of the seat and the bottom of the head restraint.
Main Menu Table of Contents Protecting Children 3. Use a razer blade or sharp knife. 4. Install the anchor plate and mounting hardware. (Canadian Models) The hardware is stored in the glove box. Driver and Passenger Safety (U.S. models only) The hardware is available for purchase from your Acura dealer (part numbers: 82410-S84-C10 for the hardware, 82419-S84-COO for the cover).
Main Menu Table of Contents Additional Information About Your Seat Belts Seat Belt System Components Your seat belt system includes lap/ shoulder belts in both seating positions. The seat belts are also equipped with automatic seat belt tensioners. The system also includes a light on the instrument panel to remind you and your passenger to fasten your belts. If the driver's seat belt is not fastened before the ignition is turned ON (II), the light will come on and a beeper will also sound.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Additional Information About Your Seat Belts To deactivate the locking mechanism, unlatch the buckle and let the seat belt fully retract. To refasten the belt, pull it out only as far as needed. See page 15 for instructions on how to wear the lap/shoulder belt properly. Seat Belt Maintenance For safety, you should check the condition of your seat belts regularly. Pull each belt out fully and look for frays, cuts, burns, and wear.
Main Menu Table of Contents Additional Information About Your SRS SRS Components Your Supplemental Restraint System (SRS) includes: Two front airbags. The driver's airbag is stored in the center of the steering wheel; the front passenger's airbag is stored in the dashboard. Both are marked "SRS AIRBAG." Automatic seat belt tensioners that tighten the front seat belts during a moderate to severe frontal collision. Sensors that can detect a moderate to severe frontal collision.
Main Menu Table of Contents Additional Information About Your SRS After a crash, you may see what looks like smoke. This is actually powder from the airbag's surface. Although the powder is not harmful, people with respiratory problems may experience some temporary discomfort. If this occurs, get out of the car as soon as it is safe to do so. During a crash, your seat belt helps restrain your lower body and torso, while the tensioner tightens and locks the seat belt to help keep you in place.
Main Menu Table of Contents Additional Information About Your Seat Belts How the Automatic Seat Belt Tensioners Work Your Acura has automatic seat belt tensioners for added protection during a severe frontal collision. If your airbags inflate, the tensioners immediately tighten the front seat belts to help hold the occupants in place. The belts will remain tight until you unbuckle them in the normal way. How the SRS Indicator Light If the light comes on or flashes on Works and off while you drive.
Main Menu Table of Contents Additional Information About Your SRS SRS Service Your Supplemental Restraint System is virtually maintenance-free, and there are no parts you can safely service. However, you must have your car serviced if: Your airbags ever inflate. The airbags, seat belt tensioners and control unit must be replaced. Do not try to remove or replace the airbags yourself. This must be done by an Acura dealer or a knowledgeable body shop. The SRS indicator light alerts you to a problem.
Main Menu Table of Contents０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Carbon Monoxide Hazard Your car's exhaust contains carbon monoxide gas. You should have no problem with carbon monoxide entering the car in normal driving if you maintain your car properly. Have the exhaust system inspected for leaks whenever: The car is raised for an oil change. You notice a change in the sound of the exhaust. The car was in an accident that may have damaged the underside. Carbon monoxide gas is toxic.
Main Menu Table of Contents Safety Labels These labels are in the locations shown. They warn yon of potential hazards that could cause serious injury. Read these labels carefully. SUN VISOR U.S. models BATTERY Canadian models If a label comes off or becomes hard to read, contact your Acura dealer for a replacement. FOLDING SPARE TIRE DASHBOARD U.S.
Main Menu Table of Contents Safety Labels EXPANSION TANK CAP Driver and Passenger Safety
Main Menu 44
Main Menu Instruments and Controls This section gives information about the controls and displays that contribute to the daily operation of your Acura. All the essential controls are within easy reach. Component Locations..................... 46 Control Locations............................ 47 Indicator Lights................................ 48 Gauges.............................................. 53 Speedometer................................ 53 Tachometer..................................
Main Menu Table of Contents Component Locations HOOD REAR WINDOW ENGINE COVER FRONT COMPARTMENT FOLDING SPARE TIRE *NSX illustration is shown.
Main Menu Table of Contents Control Locations HEADLIGHT SWITCH (P.56) TURN SIGNAL LEVER (P.58) WINDSHIELD WIPER CONTROLS (P.59) HAZARD WARNING SWITCH (P.60) HOOD RELEASE HANDLE (P.133) DIGITAL CLOCK (P.83) DOOR LOCK SWITCH (P.69) AUTOMATIC CLIMATE CONTROL (P.90) POWER WINDOW SWITCHES (P.73) AUDIO SYSTEM (P.100) MIRROR CONTROLS (P.82) TRUNK RELEASE BUTTON (P.70) FUEL FILL DOOR RELEASE (P.129) SHIFT LOCK RELEASE (P.154) (Automatic transmission only) SEAT ADJUSTMENT SWITCH (P.
Main Menu Table of Contents Indicator Lights The instrument panel has many indicators to give you important information about your car.
Main Menu Table of Contents Indicator Lights Seat Belt Reminder Light This indicator flashes for several seconds when you turn the ignition ON (II). It flashes as a reminder to you and your passenger to fasten the seat belts. A beeper also sounds if you have not fastened your seat belt. If you do not fasten your seat belt, the beeper will stop after a few seconds but the light stays on until you do. Both the light and the beeper stay off if you fasten your seat belt before turning on the ignition.
Main Menu Table of Contents Indicator Lights Restraint SRS Supplemental System Indicator This indicator lights when you turn the ignition switch ON (II). If it comes on at any other time, it indicates a problem in the supplemental restraint system. For complete information, see page 39. Instruments and Controls US Canada ABS Anti-lock Brake System (ABS) Indicator This light normally comes on when you turn the ignition switch ON (II) and goes off after the engine starts.
Main Menu Table of Contents Indicator Lights Door and Lamp Monitor (Except NSX-T) (NSX-T) All the lights in the monitor display come on for a few seconds when you turn the ignition switch ON (II). Traction Control System (TCS) Indicator This indicator has three functions: Electric Power Steering (EPS) Indicator This light normally comes on when you turn the ignition ON (II) and goes off after the engine starts. If it comes on at any other time, there is a problem in the Electric Power Steering system.
Main Menu Table of Contents Indicator Lights Turn Signal and Hazard Warning Indicators The left or right turn signal light blinks when you signal a lane change or turn. If the light does not blink or blinks rapidly, it usually means one of the turn signal bulbs is burned out (see page 218). Replace the bulb as soon as possible, since other drivers cannot see that you are signalling. When you turn on the Hazard Warning switch, both turn signal lights blink.
Main Menu Table of Contents Gauges TEMPERATURE GAUGE TACHOMETER SPEEDOMETER OIL PRESSURE GAUGE Speedometer U.S. Models This shows your speed in miles per hour (mph). The smaller inner numbers are the speed in kilometers per hour (km/h). Canadian Models This shows your speed in kilometers per hour (km/h). The smaller inner numbers are the speed in miles per hour (mph). Tachometer The tachometer shows the engine speed in revolutions per minute (rpm).
Main Menu Table of Contents Gauges FUEL GAUGE VOLTMETER ODOMETER Voltmeter This meter shows you the battery voltage when the ignition is ON (II). A prolonged reading of lower than 11 volts can indicate a problem with the battery or charging system. Have your car inspected by your Acura dealer. TRIP METER TRIP METER RESET BUTTON Fuel Gauge This shows how much fuel you have. It is most accurate when the car is on level ground.
Main Menu Table of Contents Steering Column Controls The two pods on the steering column contain controls for driving features you use most often. The left pod has controls for the turn signals, headlights, high beams, and the rear window defogger. The right pod has controls for the windshield washers and wipers, cruise control and hazard warning lights. Underneath the instrument panel are the headlight motor switch, instrument panel brightness control, and the TCS On/Off switch.
Main Menu Table of Contents Steering Column Controls Headlights If you leave the lights on with the ignition switch in ACCESSORY (I) or LOCK (0), you will hear a reminder chime when you open the driver's door. To flash the high beams when the headlight doors are closed, pull back and hold the turn signal lever. This simultaneously raises the headlight doors and turns on the high beams. Release the lever and the high beams go off. Within a few seconds, the headlight doors will close automatically.
Main Menu Table of Contents Steering Column Controls Headlight Motor Instrument Panel Brightness Rear Window Defogger HEADLIGHT MOTOR BUTTON INSTRUMENT PANEL BRIGHTNESS KNOB To raise and lower the headlight doors without turning on the headlights, push the dashboard button behind the left pod. The knob on the dashboard behind the left pod controls the brightness of the instrument panel lights. Push the knob to get it to pop out.
Main Menu Table of Contents Steering Column Controls Turn Signals To signal a lane change, push lightly on the turn signal lever in the proper direction and hold it. The lever will return to the center position as soon as you release it. TURN SIGNAL LEVER Make sure the rear window is clear and you have good visibility before starting to drive. The defogger and antenna wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side to side.
Main Menu Table of Contents Steering Column Controls Windshield Wipers The lever on the right pod controls the windshield wipers and washers. The rotary switch at the end of the lever has three positions: INT: intermittent LO: low speed HI: high speed In intermittent, the wipers operate every few seconds. You can vary how often the wipers sweep the windshield by turning the INT TIME ring next to the rotary switch. In low speed and high speed, the wipers run continuously.
Main Menu Table of Contents Steering Column Controls Windshield Washers Hazard Warning Cruise Control Master Switch To clean the windshield, pull back on the wiper control lever. The washers spray until you release the lever. The wipers run at low speed while you're pulling the lever, then complete one more sweep of the windshield after you release it. Push the large red button on the right pod to turn on the hazard warning lights (four-way flashers).
Main Menu Table of Contents Steering Column Controls Steering Wheel Adjustment See page 16 for important safely information about how to properly position the steering wheel. Make any steering wheel adjustment before you start driving. ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ After you have adjusted the steering wheel, make sure you have securely locked it in place by moving it in and out and up and down.
Main Menu Table of Contents Steering Wheel Controls ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Cruise Control Cruise control allows you to maintain a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It should be used for cruising on straight, open highways. It is not recommended for conditions such as city driving, winding roads, slippery roads, heavy rain, or bad weather. You should have full control of the car under those conditions.
Main Menu Table of Contents Steering Wheel Controls RESUME/accel cruise control. To resume the set speed, press the RESUME/accel button. The CRUISE CONTROL light on the instrument panel comes on. When climbing a steep hill, the automatic transmission may downshift to hold the set speed. Changing the Set Speed You can increase the set cruising speed in any of these ways: SET/decel 3. Press and release the SET/decel button on the steering wheel.
Main Menu Table of Contents Steering Wheel Controls Even with the cruise control turned on, you can still use the accelerator pedal to speed up for passing. After completing the pass, take your foot off the accelerator pedal. The car will return to the set cruising speed. Resting your foot on the brake or clutch pedal will cause the cruise control to cancel. Cancelling the Cruise Control You can cancel the cruise control in any of these ways: Tap the brake or clutch pedal.
Main Menu Table of Contents Keys and Locks Keys Acura-approved key blanks. KEY NUMBER PLATE MASTER KEYS (Black) VALET KEY (Gray) These keys contain electronic circuits that are activated by the Immobilizer System. They will not work to start the engine if the circuits are damaged. Protect the keys from direct sunlight, high temperature, and high humidity. Do not drop the keys or set heavy objects on them. Your car comes with two master keys and a valet key.
Main Menu Table of Contents Keys and Locks Learning Key If you attempt to use the learning key to start your car's engine, it may cause a malfunction in the system that makes your master and valet keys unusable. If this happens, you should contact your Acura dealer. If you need a new key made, take the key number plate, the learning key, and all other keys that came with your car to your Acura dealer. You should also receive a small case containing a learning key.
Main Menu Table of Contents Keys and Locks The system may not recognize your key's coding if another immobilizer key or other metal object is near the ignition switch when you insert the key. To make sure the system recognizes the key code: Do not keep other immobilizer keys on the same key ring. Use a plastic or leather key fob, not metal. Keep other keys away from your vehicle's key and the ignition switch while trying to start the engine.
Main Menu Table of Contents０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Keys and Locks LOCK (0) — You can insert or remove the key only in this position. To switch from ACCESSORY to LOCK, you must push the key in slightly as you turn it. If your car has an automatic transmission, the shift lever must also be in Park. The antitheft lock will lock the steering column when you remove the key. If the front wheels are turned, the anti-theft lock may sometimes make it difficult to turn the key from LOCK to ACCESSORY.
Main Menu Table of Contents Keys and Locks Power Door Locks DOOR LOCK SWITCH LOCK TAB Both doors will lock when you use the key to lock either door from the outside. Unlocking the driver's door with the key unlocks only that door. Unlocking the passenger's door with the key unlocks both doors. To lock the door without the key, push the lock tab down and close the door. Each door has a door lock switch. Either switch locks and unlocks both doors.
Main Menu Table of Contents Keys and Locks Lockout Prevention Trunk If you forget and leave the key in the ignition switch. Lockout Prevention will not allow you to lock the driver's door. With the driver's door open and the key in the ignition, both door lock switches are disabled. If you try to lock an open driver's door by pushing the lock tab down, the tabs on both doors pop up. Pushing the lock tab down on the passenger's door only locks that door.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２ Keys and Locks Glove Box GLOVE BOX An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt. Always keep the glove box closed while driving. TRUNK MAIN SWITCH To protect items in the trunk when you need to give the key to someone else: Open the glove box by squeezing the handle. Close it with a firm push. Lock or unlock the glove box with the master key.
Main Menu Table of Contents Seat Adjustments See pages 12 — 13 for important safety information and warnings about how to properly position seats and seat-backs. Adjust the seat before you start driving. The power seats in your car are adjusted with the two switches on the outside of the seat bottom. Push the front switch forward or backward to adjust the distance to the steering wheel and pedals.
Main Menu Table of Contents Power Windows Your car's windows are electricallypowered. Turn the ignition switch to ON (II) to raise or lower either window. DRIVER'S WINDOW SWITCH The driver's armrest has a master power window control panel. To open the passenger's window, push down on the switch and hold it down until the window reaches the desired ０３／０７／１０ ３１Ｓ５Ａ９３０ position.１６：１１：０９ To close the window, push up on the window switch.
Main Menu Table of Contents Power Windows The master control panel also contains these extra features: AUTO — To open the driver's window fully, push the window switch firmly down and release it. The window automatically goes all the way down. To stop the window from going all the way down, push the window switch up briefly. To open the driver's window only partially, push the window switch down lightly and hold it. The window will stop as soon as you release the switch.
Main Menu Table of Contents Removable Roof Panel On the NSX-T Your Acura's roof panel has a single release handle on each side, making it easy to remove and install. When not in use, the roof panel can be stored in a special holder under the rear window. Always clean and dry the roof panel before you remove it so dirt and water do not fall in the interior and engine compartment. Do not put any items other than the roof panel in the roof holder or you can damage the roof holder.
Main Menu Table of Contents Removable Roof Panel Removing and Storing 1. Open both windows. 2. Turn off the engine and set the parking brake. 3. Release each side of the roof by pushing the lock tab sideways and pulling down the release lever. Instruments and Controls 4. Open the door. Locate the rear window release handle on the rear of the driver's door opening, next to the seat. Pivot this handle towards the driver's seat. The rear window will pop up slightly. 5.
Main Menu Table of Contents Removable Roof Panel 6. Pull up the roof cover release lever and raise the roof cover. 7. Unsnap the hook end of the strap from the rear window frame. 8. Put the hook around the edge of the roof cover to hold it up.
Main Menu Table of Contents Removable Roof Panel 9. Lift the roof straight up off the car. Since the roof must go in the holder backwards, it is recommended that you carry it around to the opposite side of the car. 10. Place the roof in the holder with the rear facing forward. Make sure the pins at both front corners of the holder are in the holes in the roof panel. Instruments and Controls 11. Lower the roof cover and push it down until it latches. Snap the hook on the window frame. 12.
Main Menu Table of Contents Removable Roof Panel panel mechanism to jam or to not latch the roof properly. If the wind noise feels unpleasant while you are driving with the roof panel removed, you can reduce the noise by inserting a plug in the hole located at each side of the rear roof pillar. These plugs are stored in the glove box. Do not use any plugs other than the ones that came with your car.
Main Menu Table of Contents Removable Roof Panel 10. Close the roof cover and snap the hook onto the window frame. Close the rear window. Roof Unlatched Indicator ROOF UNLATCHED INDICATOR 8. Set the roof in place on the car. Make sure all four corners are sitting flush with the car body. Instruments and Controls 9. Secure the roof by turning each release lever until the lock tab clicks forward. Pull on the levers to make sure they are locked.
Main Menu Table of Contents Removable Roof Panel Maintenance Dust is the main cause of creaks or other sounds coming from the roof. Regularly clean the roof panel and body seals with glass cleaner and a soft cloth. Every three to six months, depending on how often the roof is removed, rub a thin film of Shin-Etsu Silicone grease (available from your Acura dealer, P/N 08798-9013) onto the seals wherever they touch the roof panel or each other.
Main Menu Table of Contents Removable Roof Panel, Mirrors Mirrors Adjusting the Power Mirrors SELECTOR SWITCH When the seals are new, the glass will seal more tightly if you open the door slightly before closing the window. Never store any items other than the roof panel in the holder. Because it is above the engine, the holder can get very warm. Instruments and Controls TAB Keep the inside and outside mirrors clean and adjusted for best visibility.
Main Menu Table of Contents Mirrors, Digital Clock Digital Clock HOUR MIN. 3. Push the appropriate edge of the adjustment switch to move the mirror right, left, up or down. 4. When you finish, move the selector switch to the center (off) position. This turns off the adjustment switch so you can't move a mirror out of position by accidentally bumping the switch. The digital clock displays the time with the ignition switch ON (II). To see the time with the ignition off, press and hold the DISPLAY button.
Main Menu Table of Contents Digital Clock, Parking Brake 4. Press and hold the MIN. button until the numbers advance to the desired time. You can use the RESET button to quickly set the time to the nearest hour. If the displayed time is before the half hour, pressing RESET button sets the clock back to the previous hour. If the displayed time is after the half hour, pressing the RESET button sets the clock forward to the beginning of the next hour. For example: 1:06 would RESET to 1:00.
Main Menu Table of Contents Console Compartment, Coin Holder Console Compartment Coin Holder CONSOLE COMPARTMENT To open the console compartment, lift the tab on the left edge. The coin holder is located in the front half of the console compartment lid. Open the coin holder by lifting up on the middle of the armrest pad.
Main Menu Table of Contents Beverage Holder, Cigarette Lighter Beverage Holder Be careful when you are using the beverage holder. A spilled liquid that is very hot can scald you or your passenger. Spilled liquids can also damage the upholstery, carpeting, and electrical components in the interior. Cigarette Lighter CIGARETTE LIGHTER The beverage holder is located in the rear half of the console compartment lid. To use the beverage holder, lift up on the middle of the armrest pad.
Main Menu Table of Contents Ashtray, Interior Lights Ashtray NOTICE ASHTRAY Open the ashtray by lifting the lid up. To close the ashtray, push the lid down. To remove it for emptying, lift the lid up to the open position, and push it up further. The ashtray will pop out slightly so you can grasp it and pull it all the way out. After emptying, push it all the way back in. Interior Lights Use the ashtray only for cigarettes, cigars, and other smoking materials.
Main Menu Table of Contents Interior Lights, Courtesy Lights Courtesy Lights DOOR LIGHT FOOTWELL LIGHT OFF ON IGNITION SWITCH LIGHT On the fixed roof model, the interior light is on the ceiling between the sun visors. It also has a three position switch which operates as described. In addition, when the three position switch is in the center position with both doors closed, the two bulbs in the interior light can be turned on separately by the pushbutton switches next to them.
Main Menu Comfort and Convenience Features The climate control system in your Acura provides a comfortable driving environment in all weather conditions. The audio sound system is very versatile. To get the most from this system, take the time to learn what the controls do. The security system helps to discourage vandalism and theft of your Acura. Climate Control System.................. 90 Fully-automatic Operation.......... 91 Semi-automatic Operation.......... 93 Air Conditioning Switch..........
Main Menu Table of Contents Climate Control System The automatic climate control system in your Acura picks the proper combination of air conditioning, heating, and ventilation to maintain the interior temperature you select. The system also adjusts the fan speed and air flow levels. CENTER VENTS The direction of air flow from the vents in the center of the dashboard and in each armrest is adjustable. Move the tab in the center of each vent up-and-down and side-to-side.
Main Menu Table of Contents Climate Control System The climate control system draws air through the exterior vents at the bottom of the windshield. Keep these vents clear of leaves and other debris. TEMPERATURE CONTROL DIAL FULLY-AUTOMATIC OPERATION SELECTED TEMPERATURE FAN SPEED DIAL For the climate control system to provide heating and cooling, the engine must be running.
Main Menu Table of Contents Climate Control System When you set the temperature to its lower limit (60°F/18°C) or its upper limit (90°F/32°C), the system runs at full cooling or heating only. It does not regulate the interior temperature. When the temperature is set between the lower and upper limits, the system regulates the interior temperature to the set value.
Main Menu Table of Contents Climate Control System Semi-automatic Operation You can manually select various functions of the Climate Control system when it is in FULL AUTO. All other features remain automatically controlled. Making any manual selection causes the word FULL to go out. Air Conditioning Switch Pressing the A / C switch turns the air conditioning on and off. You will see ON or OFF in the display.
Main Menu Table of Contents Climate Control System Mode Button Use the MODE button to select the vents the air flows from. Some air will flow from the dashboard corner vents in all modes. Each time you press the MODE button, the display shows the mode selected. Press the button four times to see all the modes. To manually select air flow direction The main air flow comes out of the dashboard and door vents. Close the door vents when using the air conditioning or the windows may fog up.
Main Menu Table of Contents Climate Control System The main air flow is divided between the dashboard/door vents and the floor vents. The main air flow comes from the floor vents.
Main Menu Table of Contents Climate Control System The main air flow is divided between the floor vents and windshield defroster vents.
Main Menu Table of Contents Climate Control System The button directs the main air flow to the windshield for faster defrosting. It also overrides any MODE selection you may have made. To defrost more quickly, turn the temperature control to 82° F- 86° F (28°C-30°C). Press and turn the fan speed dial to high. Warmed air will then flow from the windshield and side defroster vents. To turn off defrost, press the AUTO or DEFROST button.
Main Menu Table of Contents Climate Control System Recirculated and Fresh Air The and buttons select the source of air going into the climate control system. draws fresh air from outside. draws air into the system from the car's interior and recirculates it. You can, for example, manually put the system in recirculation mode when driving through an area of smoke or fumes. When you press the or button, the light in that button comes on.
Main Menu Table of Contents Climate Control System Temperature Sensors The climate control system has temperature sensors located on the dashboard and in the center console. Do not cover these sensors or spill any liquid on them.
Main Menu Table of Contents Audio System The sound system in your NSX can deliver excellent reception on both the AM and FM bands. The cassette system uses Dolby B* noise reduction to give excellent sound reproduction on tapes that were recorded using that feature. The system can also sense when a metal or chromium-dioxide (CrO2) tape is being played, and adjusts accordingly. * Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corpo- LOW ration.
Main Menu Table of Contents Audio System Operating the Radio The ignition switch must be in ACCESSORY (I) or ON (II) to operate the audio system. Turn the system on by pressing the ON/OFF button. The radio comes on and displays the frequency of the station it was last tuned to. The power antenna will also extend. Adjust the volume with the VOL dial (outside ring of the left knob). Select the AM or FM band by pushing the A M / F M button. The selected band is shown next to the frequency display.
Main Menu Table of Contents Audio System Finding a Radio Station To tune to a station, turn the TUNE dial (outside ring of the right knob). Turn it clockwise to tune to a higher frequency, and counterclockwise to tune to a lower frequency. The STEREO indicator next to the frequency display lights if the station is broadcasting in FM stereo. The STEREO indicator will flash if you are driving in an area where the radio signal is weak. This system cannot receive AM broadcasts in stereo.
Main Menu Table of Contents Audio System The easiest way to find your favorite stations is to set their frequencies into the eight preset buttons. To do this, tune to the desired station as described previously. Press one of the preset buttons (1 — 8) and hold it until you hear a beep. You can preset eight stations on each band. When you press the SEEK bar, the radio scans the selected band and stops on the next station with a strong signal.
Main Menu Table of Contents Audio System The A. SELECT function allows you to find stations easily when you are in an unfamiliar area. Press the A. SELECT button. The system automatically scans both the AM and FM bands, memorizes the eight strongest on each band, and stores them in the eight preset buttons. You can then use the buttons to tune to those stations. The light in the A. SELECT button stays on as a reminder. You cannot manually change any presets with A. SELECT on.
Main Menu Table of Contents Audio System Adjusting the Sound Use the TREB and BASS knobs to adjust the tone quality to your liking. Push on the TREB knob to get both to pop out. The outside ring changes the bass level, and the inner knob changes the treble level. When you have finished the adjustments, push the knobs back in so there is less chance of accidentally changing your settings. The BAL control adjusts the sound balance between the speakers. Push on the knob so it pops out.
Main Menu Table of Contents Audio System Audio System Lighting You can use the instrument panel brightness control dial to adjust the illumination of the audio system (see page 57). The audio system illuminates when the parking lights are on, even if the radio is turned off. Stations must use these exact frequencies. It is fairly common for stations to round-off the frequency in their advertising, so your radio could display a frequency of 100.
Main Menu Table of Contents Audio System As required by the FCC: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills. Your radio then receives both the direct signal from the station's transmitter, and the deflected signal. This causes the sound to distort or flutter.
Main Menu Table of Contents Audio System Operating the Cassette Player Make sure the radio is ON. Insert the cassette with the tape opening to the right. Push the cassette most of the way into the slot. It will be pulled in the rest of the way and begin to play. The display will change from the radio frequency to the word TAPE. The or will light to show you which side of the cassette is playing. The indicates the side you inserted facing upward is now playing.
Main Menu Table of Contents Audio System Dolby B noise reduction turns on when you insert a cassette. If the tape was not recorded with Dolby B noise reduction, turn it off by pressing the button. DOLBY NR ON/OFF If you play a metal or chromiumdioxide (CrO2) tape, the system automatically senses it. The METAL indicator in the frequency display lights.
Main Menu Table of Contents Audio System To remove the cassette from the drive, press the (Eject) button. The system automatically ejects the cassette whenever you turn off the system or the ignition switch.
Main Menu Table of Contents Audio System Cassette Search Functions You can use the preset buttons to control tape movement while playing a cassette. Six functions are available: Fast forward, Rewind, Repeat, Replay, Skip, and Scan. Press to fast forward the tape. Press to rewind the tape. To stop fast forward or rewind, press PLAY. Fast forward or rewind stops automatically at the end of the tape. The system reverses direction, then begins to play.
Main Menu Table of Contents Audio System The REPEAT function plays the current song or passage over again. Press REPEAT to enable it. The light in the button stays lit to remind you. When the system senses a silent period in the program (such as the end of a song), it rewinds the tape to the previous silent period. It continues to repeat this same passage as long as REPEAT is on. To turn it off, press the button again. Pressing or also turns off REPEAT.
Main Menu Table of Contents Audio System The REPLAY function is similar to REPEAT. When you press this button, the system immediately goes into rewind. The light in the REPLAY button flashes during rewind. When it senses a silent period on the tape, the system stops rewinding and goes back to PLAY. Unlike REPEAT, this function replays a selection only once. If you do not press again, the tape will play straight through.
Main Menu Table of Contents Audio System The SKIP function allows you to skip over a song or other passage. When you press this button, the system goes into fast forward until it senses a silent period on the tape. The light in the SKIP button flashes during fast forward. When the system finds a silent period, it goes back to PLAY.
Main Menu Table of Contents Audio System SCAN allows you to search a tape for a desired passage. When you press this button, the system goes into fast forward. It goes back to PLAY when it senses a silent period on the tape. It stays in PLAY for eight seconds so you can listen to that passage and decide if you want to hear it all. If you are not interested in that passage, leave the system alone.
Main Menu Table of Contents Audio System The REPLAY, SKIP and SCAN functions use silent periods on the tape to find the end of a selection. These features may not work satisfactorily on tapes that have almost no gap between songs, a high noise level between songs, or silent periods in the middle of songs. Caring for the Cassette Player CLEAN LIGHT If you do not clean the cassette player regularly, it may eventually become impossible to remove the contamination with a normal cleaning kit.
Main Menu Table of Contents Audio System Do not leave cassettes sitting where they are exposed to high heat or humidity, such as on top of the dashboard or in the player. If a cassette is exposed to extreme heat or cold, let it reach a moderate temperature before putting it in the player. Look at the cassette before you insert it. If the tape is loose, tighten it by turning a hub with a pencil or your finger. If the label is peeling off, do not put it in the player.
Main Menu Table of Contents Audio System Operating the CD Changer (Optional) A trunk-mounted Compact Disc changer is available for your car. It holds up to six discs, providing several hours of continuous programming. You operate the CD changer with the same controls used for the radio and cassette player. Load the desired CDs in the magazine and load the magazine in the changer according to the instructions that came with the unit. Play only standard round discs.
Main Menu Table of Contents Audio System To select another disc, press PROG. The next CD in the changer is loaded and starts to play from the first track. The new CD and track numbers are displayed. To return to the radio function, press the A M / F M button. To turn the system completely off, press the ON/OFF button.
Main Menu Table of Contents Audio System You can use the preset buttons while a CD is playing to select passages and change tracks. To move rapidly within a track, press and hold the button to move forward or the button to move backward. The player will fast forward or reverse for as long as you hold the button. It goes to normal play mode when you release the button.
Main Menu Table of Contents Audio System To replay the current track, press REPEAT. The indicator in the preset button will come on as a reminder. At the end of the track, the system skips back to its beginning. That track will repeat continuously until you cancel REPEAT by pressing the button again.
Main Menu Table of Contents Audio System To search for a particular program on a disc, press SCAN. The system will skip forward to the next track and begin to play it. If you do not touch any of the controls, the system skips to the beginning of the next track after ten seconds and begins to play that. When the system gets to a track you want to hear all the way through, press SCAN again. You can only scan tracks on the disc currently being played.
Main Menu Table of Contents Audio System You can get the CD changer to randomly select tracks by pressing A. SELECT. The indicator in the button lights as a reminder. With this active, the system selects and plays tracks randomly rather than sequentially. Random selection only works on the disc currently playing, not across all six discs. Cancel random selection by pressing A. SELECT again. Random selection is also cancelled by selecting the SCAN function.
Main Menu Table of Contents Audio System Protecting Compact Discs Handle a CD by its edges; never touch either surface. Contamination from fingerprints, liquids, felt-tip pens, and labels can cause the CD to not play properly, or possibly jam in the drive. When a CD is not being played, store it in its case to protect it from dust and other contamination. To prevent warpage, keep CDs out of direct sunlight and extreme heat. To clean a disc, use a clean soft cloth.
Main Menu Table of Contents Audio System CD Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Acura dealer.
Main Menu Table of Contents Security System The security system sets automatically fifteen seconds after you lock the doors, hood, rear window, roof panel (NSX-T) and trunk. For the system to activate, you must lock the doors from the outside with the key, lock tab, or door lock switch (see page 69). The security system light next to the driver's door lock starts blinking immediately to show you the system is setting itself. The security system helps to protect your car and valuables from theft.
Main Menu Before Driving Before you begin driving your Acura, you should know what gasoline to use, and how to check the levels of important fluids. You also need to know how to properly store luggage or packages. The information in this section will help you. If you plan to add any accessories to your car, please read the information in this section first. Break-in Period.............................. 128 Gasoline.......................................... 128 Service Station Procedures ..........
Main Menu Table of Contents Break-in Period, Gasoline Break-in Period Help assure your car's future reliability and performance by paying extra attention to how you drive during the first 600 miles (1,000 km). During this period: Avoid full-throttle starts and rapid acceleration. Do not exceed 5,500 rpm for the first 600 miles (1,000 km) of operation. Avoid hard braking. New brakes need to be broken-in by moderate use for the first 200 miles (300 km).
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Service Station Procedures Filling the Fuel Tank Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. Stop the engine and keep heat, sparks, and flame away. Handle fuel only outdoors. Wipe up spills immediately. FUEL FILL CAP 1. Because the fuel fill cap is on the driver's side of the car, park with that side closest to the service station pumps. 3. Remove the fuel fill cap slowly.
Main Menu Table of Contents Service Station Procedures 4. Stop filling the tank after the fuel nozzle automatically clicks off. Do not try to "top off" the tank, leave some room for the fuel to expand with temperature changes. Opening the Engine Compartment RELEASE HANDLE REAR WINDOW Your car has an on-board refueling vapor recovery system to help keep fuel vapors from going into the atmosphere.
Main Menu Table of Contents Service Station Procedures Oil Check NSX-T SUPPORT ROD ENGINE COVER ENGINE COVER DIPSTICK NSX 3. Lift the engine cover. 4. NSX-T Pull the support rod out of its clip and insert the end into the square hole in the engine cover bracket. Except NSX-T Pull the support rod out of its clip and insert the end into the square hole in the window latch bracket. To Close the Rear Window: Snap the support rod back into the clip and lower the engine cover or roof holder.
Main Menu Table of Contents Service Station Procedures UPPER MARK LOWER MARK 2. Wipe the dipstick with a clean cloth or paper towel. 3. Insert it all the way back in its tube. 4. Remove the dipstick again and check the level. It should be between the upper and lower marks. If it is near or below the lower mark, see Adding Oil on page 179.
Main Menu Table of Contents Service Station Procedures Engine Coolant Check EXPANSION TANK Refer to Owner Maintenance Checks on page 177 for information on checking other items in your Acura. Checking the Front Compartment HOOD RELEASE HANDLE MAX MIN Look at the coolant level in the expansion tank. Make sure it is between the MAX and M I N lines. If it is below the M I N line, see Adding Engine Coolant on page 183 for information on adding the proper coolant. 1.
Main Menu Table of Contents Service Station Procedures LATCH HANDLE If you can open the hood without lifting the hood latch handle, or the hood latch handle moves stiffly or does not spring back as before, the mechanism should be cleaned and lubricated (see page 197). SUPPORT ROD HOOD 2. Standing in front of the car, put your fingers under the front edge of the hood to the right of center. Slide your hand to the left until you feel the hood latch handle.
Main Menu Table of Contents Service Station Procedures Refer to Owner Maintenance Checks on page 177 for information on checking other items in your Acura. CLIP 5. Snap the support rod back into its holding clip. 6. Lower the hood about halfway down and let the hood drop. After closing the hood, make sure it is securely latched.
Main Menu Table of Contents Fuel Economy The condition of your car and your driving habits are the two most important things that affect the fuel mileage you get. Car Condition Always maintain your car according to the maintenance schedule. This will keep it in top operating condition. An important part of that maintenance is the Owner Maintenance Checks (see page 177). For example, an underinflated tire causes more "rolling resistance," which uses fuel.
Main Menu Table of Contents０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Accessories and Modifications Modifying your car, or installing some non-Acura accessories, can make your car unsafe. Before you make any modifications or add any accessories, be sure to read the following information. Accessories Your dealer has Genuine Acura accessories that allow you to personalize your car. These accessories have been designed and approved for your car, and are covered by warranty.
Main Menu Table of Contents Accessories and Modifications Modifications Do not remove any original equipment or modify your car in any way that would alter its design or operation. This could make your car unsafe and illegal to drive. In addition, any modifications that decrease ground clearance increase the chance of undercarriage parts striking a curb, speed bump, or other raised object, which could cause your airbags to deploy.
Main Menu Table of Contents Carrying Cargo Your car has several convenient storage areas so you can stow cargo safely. GLOVE BOX The glove box, and the pockets in the front doors, are designed for small, lightweight items. The trunk is intended for larger, heavier items. However, carrying too much cargo, or improperly storing it, can affect your car's handling, stability and operation and make it unsafe. Before carrying any type of cargo, be sure to read the following pages.
Main Menu Table of Contents０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Carrying Cargo Load Limit The maximum load for your car is 400 Ibs (185 kg). This figure includes the total weight of all occupants, cargo, and accessories. To figure out how much cargo you can carry: Add up the weight of all occupants. Subtract the total from 400 Ib (185 kg). The final number is the total weight of cargo you can carry.
Main Menu Table of Contents Carrying Cargo Carrying Cargo in the Trunk Distribute cargo evenly on the floor of the trunk, placing the heaviest items on the bottom and as far forward as possible.
Main Menu Table of Contents General Precautions Your Acura is designed to give you optimum handling and performance on well-maintained roads. As part of this design, your car has a minimum of ground clearance and very lowprofile tires. Use caution if you should drive your car on very rough or rutted roads. You could damage the suspension and underbody by bottoming out. Going too fast over parking lot "speed bumps" can also cause damage.
Main Menu Driving This section gives you tips on starting the engine under various conditions, and how to operate the manual and automatic transmissions. It also includes important information on parking your car, the braking system and the Traction Control System. Preparing to Drive......................... 144 Starting the Engine........................ 145 Starting in Cold Weather at High Altitude ..................... 145 6-speed Manual Transmission..... 146 Recommended Shift Points......
Main Menu Table of Contents Preparing to Drive You should do the following checks and adjustments every day before you drive your car. 1. Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice. 2. Check that the hood, trunk and rear window are fully closed. 3. Visually check the tires. If a tire looks low, use a gauge to check its pressure. 4. Check that any items you may be carrying with you inside are stored properly or fastened down securely. 5.
Main Menu Table of Contents Starting the Engine 1. Apply the parking brake. 2. In cold weather, turn off all electrical accessories to reduce the drain on the battery. 3. Manual Transmission: Push the clutch pedal down all the way. START (III) does not function unless the clutch pedal is depressed. Automatic Transmission: Make sure the shift lever is in Park. Press on the brake pedal. 4. Without touching the accelerator pedal, turn the ignition key to the START (III) position.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ 6-speed Manual Transmission Come to a full stop before you shift into Reverse. You can damage the transmission by trying to shift into Reverse with the car moving. Push down the clutch pedal, and pause for a few seconds before shifting into Reverse, or shift into one of the forward gears for a moment. This stops the gears so they won't "grind." The manual transmission is synchronized in all forward gears for smooth operation.
Main Menu Table of Contents 6-speed Manual Transmission Recommended Shift Points Drive in the highest gear that lets the engine run and accelerate smoothly. This will give you the best fuel economy and effective emissions control. The following shift points are recommended: Engine Speed Limiter If you exceed the maximum speed for the gear you are in, the engine speed will enter into the tachometer's red zone. If this occurs, you may feel the engine cut in and out.
Main Menu Table of Contents 6-speed Manual Transmission Reverse Lockout The 6-speed manual transmission has an electric lockout so you cannot accidentally shift from Fifth to Reverse instead of Sixth. If you cannot shift to Reverse when the car is stopped: 2. If you are still unable to shift to Reverse, apply the parking brake and turn the ignition key to ACCESSORY (I) or LOCK (0). 3. Depress the clutch pedal and shift to Reverse. 4. With the clutch pedal still depressed, start the engine. 1.
Main Menu Table of Contents Automatic Transmission Your Acura's transmission has four forward speeds, and is electronically controlled for smoother shifting. It also has a "lock-up" torque converter for better fuel economy. You may feel what seems like another shift when the converter locks. Shift Lever Position Indicator This display is in the tachometer. It shows you the position of the console shift lever.
Main Menu Table of Contents Automatic Transmission Shift Lever Positions SHIFT LEVER RELEASE BUTTON The console shift lever has seven positions. It must be in Park or Neutral to start the engine. The shift lever on the steering column's right pod allows you to shift up and down manually when the console shift lever is in the " 3 / M " position. Driving Park (P) — This position mechanically locks the transmission. Use Park whenever you are turning off or starting the engine.
Main Menu Table of Contents Automatic Transmission If you have done all of the above and still cannot move the lever out of Park, see Shift Lock Release on page 154 . You must also press the release button to shift into Park. To avoid transmission damage, come to a complete stop before shifting into Park. The shift lever must be in Park before you can remove the key from the ignition switch. Reverse (R) — To shift to Reverse from Park, see the explanation under Park.
Main Menu Table of Contents Automatic Transmission SportShift (3/M) — With the console shift lever in this position, you can use the SportShift lever on the right pod to shift gears; much like a manual transmission without a clutch pedal. Each time you push up on the SportShift lever, the transmission will shift up to the next higher gear. Push down on the lever to downshift. The number of the selected gear is displayed next to the " M " indicator (See page 149).
Main Menu Table of Contents Automatic Transmission Second (2) — To shift to Second, press the release button on the side of the shift lever. This position locks the transmission in second gear. It does not downshift to first gear when you come to a stop. Second gives you more power when climbing, and increased engine braking when going down steep hills. Use second gear when starting out on a slippery surface or in deep snow. It will help reduce wheelspin.
Main Menu Table of Contents Automatic Transmission Shift Lock Release This allows you to move the shift lever out of Park if the normal method of pushing on the brake pedal and pressing the release button does not work. RELEASE BUTTON 1. Set the Parking brake. 2. Remove the key from the ignition switch. 3. Put a cloth on the edge of the Shift Lock Release slot cover next to the shift lever. Use a small flat-tipped screwdriver or finger nail file to remove the cover.
Main Menu Table of Contents Parking Always use the parking brake when you park your car. The indicator on the instrument panel shows that the parking brake is not fully released; it does not indicate that the parking brake is firmly set. Make sure the parking brake is set firmly or your car may roll if it is parked on an incline. If your car has an automatic transmission, set the parking brake before you put the transmission in Park.
Main Menu Table of Contents The Braking System Your Acura is equipped with disc brakes at all four wheels. A power assist helps reduce the effort needed on the brake pedal. The ABS helps you retain steering control when braking very hard. Put your foot on the brake pedal only when you intend to brake. Resting your foot on the pedal keeps the brakes applied lightly, causing them to build up heat. Heat build-up can reduce how well your brakes work.
Main Menu Table of Contents The Braking System Brake System Design The hydraulic system that operates the brakes has two separate circuits. Each circuit works diagonally across the car (the left-front brake is connected with the right-rear brake, etc.). If one circuit should develop a problem, you will still have braking at two wheels. Anti-lock Brakes Your car has an Anti-lock Brake System (ABS) as standard equipment.
Main Menu Table of Contents The Braking System You should never pump the brake pedal, this defeats the purpose of the ABS. Let the ABS work for you by always keeping firm, steady pressure on the brake pedal as you steer away from the hazard. This is sometimes referred to as "stomp and steer." Important Safety Reminders ABS does not reduce the time or distance it takes to stop the car, it only helps with steering control during braking.
Main Menu Table of Contents The Braking System ABS Indicator The ABS is self-checking. If anything goes wrong, the ABS indicator on the instrument panel comes on (see page 50). This means the anti-lock function of the braking system has shut down. The brakes still work like a conventional system without antilock, providing normal stopping ability. You should have the dealer inspect your car as soon as possible. ANTI-LOCK BRAKE SYSTEM INDICATOR* * U.S.
Main Menu Table of Contents Traction Control System You should still install winter tires on your car during the winter. Exercise the same caution in winter driving as you would if your car was not equipped with TCS. Your Acura is equipped with a Traction Control System (TCS). TCS assists you in maintaining traction while accelerating on slippery surfaces. It does this by regulating the engine's power output when it senses either of the drive wheels starting to spin.
Main Menu Table of Contents Traction Control System TCS ON/OFF Switch TCS INDICATOR LIGHT The Traction Control System turns on every time you start the engine, even if you turned it off the last time you drove the car. TCS Indicator The TCS indicator comes on or flashes under the following conditions: When you turn the ignition switch to ON (II). TCS ON/OFF SWITCH This switch is on the dashboard behind the right control pod. It lets you turn the Traction Control System on and off.
Main Menu Table of Contents Driving in Bad Weather Rain, fog, and snow conditions require a different driving technique because of reduced traction and visibility. Keep your car wellmaintained and exercise greater caution when you need to drive in bad weather. The cruise control should not be used in these conditions. Driving Driving Technique — Always drive slower than you would in dry weather. It takes your car longer to react, even in conditions that may seem just barely damp.
Main Menu Table of Contents Driving in Bad Weather, Towing a Trailer Towing a Trailer Your NSX is not designed to tow a trailer. Attempting to do so can void your warranties. Traction — Check your tires frequently for wear and proper pressure. Both are important in preventing "hydroplaning" (loss of traction on a wet surface). In the winter, mount snow tires on all four wheels for the best handling. Watch road conditions carefully, they can change from moment to moment.
Main Menu
Main Menu Maintenance This section explains why it is important to keep your car well maintained and to follow basic maintenance safety precautions. This section also includes Maintenance Schedules for normal driving and severe driving conditions, a Maintenance Record, and instructions for simple maintenance tasks you may want to take care of yourself. If you have the skills and tools to perform more complex maintenance tasks on your Acura, you may want to purchase the Service Manual.
Main Menu Table of Contents Maintenance Safety Regularly maintaining your car is the best way to protect your investment. Proper maintenance is essential to ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ your safety and the safety of your passengers. It will also reward you with more economical, trouble-free driving and help reduce air pollution. Improperly maintaining this car or failing to correct a problem before driving can cause a crash in which you can be seriously hurt or killed.
Main Menu Table of Contents Maintenance Safety Important Safety Precautions Before you begin any maintenance, make sure your car is parked on level ground and that the parking brake is set. Also, be sure the engine is off. This will help to eliminate several potential hazards: Carbon monoxide poisoning from engine exhaust. Be sure there is adequate ventilation whenever you operate the engine. Burns from hot parts. Let the engine and exhaust system cool before touching any parts. Injury from moving parts.
Main Menu Table of Contents Maintenance Schedule The Maintenance Schedule specifies how often you should have your car serviced and what things need attention. It is essential that you have your car serviced as scheduled to retain its high level of safety, dependability, and emissions control performance. The services and time or distance intervals shown in the maintenance schedule assume you will use your car as normal transportation for your passenger and possessions.
Main Menu Table of Contents Maintenance Schedule Your authorized Acura dealer knows your car best and can provide competent, efficient service. However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or person who is skilled in this type of automotive service. Keep all the receipts as proof of completion, and have the person who does the work fill out the Maintenance Record. Check your warranty booklet for more information.
Main Menu Table of Contents U.S. Owners Follow the Normal Conditions Maintenance Schedule if the severe driving conditions specified in the Severe Conditions Maintenance Schedule do not apply. NOTE: If you only OCCASIONALLY drive under a "severe" condition, you should follow the Normal Conditions Maintenance Schedule. Canadian Owners Follow the Maintenance Schedule for Severe Conditions. #: See information on maintenance and emissions warranty, last column, page 169.
Main Menu Table of Contents Service at the indicated distance or time, whichever comes first. Do the items in A, B, C as required for each distance/time interval. Follow this schedule if the severe driving conditions described in the Severe Conditions Schedule on the next page do not apply. Canadian owners: Follow the schedule for Severe Conditions. # : See information on maintenance and emissions warranty, last column, page 169. Note: Check engine oil and coolant at each fuel stop.
Main Menu Table of Contents U.S. Owners Follow the Severe Conditions Maintenance Schedule if you drive your vehicle MAINLY under one or more of the following conditions: Driving less than 5 miles (8 km) per trip or, in freezing temperatures, driving less than 10 miles (16 km) per trip. Driving in extremely hot [over 90°F (32°C)] conditions. Extensive idling or long periods of stop-and-go driving. Driving in mountainous conditions. Driving on muddy, dusty, or de-iced roads.
Main Menu Table of Contents Use this schedule if your vehicle is MAINLY driven in any of the following Severe Conditions, or normally driven in Canada; otherwise use the Normal Schedule. Service at the indicated distance or time, whichever comes first. Do the items in A, B, C, D as required for each distance/time. Note : Check engine oil and coolant at each fuel stop. Check and adjust valve clearance, cold engine, if noisy.
Main Menu Table of Contents # : * Maintenance See information on maintenance and emissions warranty, last column, page 169. 1 : See Timing Belt on page 206 to determine need for replacement.
Main Menu Table of Contents Required Maintenance Record (for Normal and Severe Schedules) You or the servicing dealer can record all completed maintenance here, whether you follow the schedule for normal conditions (page 170) or severe conditions (page 172). Keep the receipts for all work done on your vehicle.
Main Menu Table of Contents Required Maintenance Record (for Normal and Severe Schedules) Maintenance
Main Menu Table of Contents Owner Maintenance Checks You should check the following items at the specified intervals. If you are unsure of how to perform any check, turn to the page given. Engine oil level — Check every time you fill the fuel tank. See page 131. Engine coolant level — Check the expansion tank every time you fill the fuel tank. See page 133. Windshield washer fluid — Check the level in the reservoir monthly.
Main Menu Table of Contents Fluid Locations BRAKE FLUID (Gray Cap) CLUTCH FLUID (Gray Cap) WASHER FLUID (Blue Cap) Maintenance AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow Loop) EXPANSION TANK CAP MANUAL TRANSMISSION FILLER BOLT ENGINE OIL FILL CAP ENGINE OIL DIPSTICK (Orange Loop)
Main Menu Table of Contents Engine Oil Adding Oil Recommended Oil Oil is a major contributor to your engine's performance and longevity. Always use a premium-grade detergent oil. It is highly recommended that you use Genuine Honda Motor Oil in your vehicle for as long as you own it. The API Service label also tells you the service classification of the oil. Always use an oil that is labeled " A P I Service SJ." This service rating may include other classifications, such as CD.
Main Menu Table of Contents Engine Oil The oil container may also display the API Certification seal. Make sure it says "For Gasoline Engines." The SAE numbers tell you the oil's viscosity or weight. Select the oil for your car according to this chart. Ambient Temperature API CERTIFICATION SEAL An oil with a viscosity of 10W-30 is preferred for improved fuel economy and year-round protection in your Acura. You may use a 5W-30 oil if the temperature in your area goes below 32° F(0°C).
Main Menu Table of Contents Engine Oil Changing the Oil and Filter Always change the oil and filter according to the time and distance (miles/kilometers) recommendations in the maintenance schedule. The oil and filter collect contaminants that can damage your engine if they are not removed regularly. Changing the oil and filter requires special tools and access from underneath the car. The car should be raised on a service station-type hydraulic lift for this service.
Main Menu Table of Contents Engine Oil 5. Put a new washer on the drain bolt, then reinstall the drain bolt. Tighten it to: 33 lbf.ft (45 N.m, 4.6 kgf.m) 6. Refill the engine with the recommended oil. Engine oil change capacity (including filter): 5.3 US qt (5.0 l ,4.4 Imp qt) 7. Replace the engine oil fill cap. Start the engine. The oil pressure indicator light should go out within five seconds. If it does not, turn off the engine and reinspect your work. 8.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Cooling System Adding Engine Coolant EXPANSION TANK Always use Genuine Honda Antifreeze/Coolant. If it is not available, you may use another major-brand non-silicate coolant as a temporary replacement. Make sure it is a high-quality coolant recommended for aluminum engines. However, continued use of any nonHonda coolant can result in corrosion, causing the cooling system to malfunction or fail.
Main Menu Table of Contents Cooling System 4. Pour coolant into the expansion tank. Fill it to the MAX line. Put the cap back on the expansion tank. Do not add any rust inhibitors or other additives to your car's cooling system. They may not be compatible with the coolant or engine components. 1. Make sure the engine and radiator are cool. 2. Turn the expansion tank cap counterclockwise, without pressing down on it, until it stops. This relieves any pressure remaining in the cooling system. 3.
Main Menu Table of Contents Cooling System Replacing Engine Coolant The cooling system should be completely drained and refilled with new coolant according to the time and distance recommendations in the maintenance schedule. Only use Genuine Honda Antifreeze/Coolant. Draining the coolant requires access to the underside of the car. Unless you have the tools and knowledge, you should have this maintenance done by a skilled mechanic. To replace the coolant: 1.
Main Menu Table of Contents Cooling System BLEEDER PLUG DRAIN PLUG 3. Start the engine. Turn the heater temperature control dial to maximum heat and turn off the engine. Make sure the engine and radiator are cool to the touch. Maintenance 4. Remove the drain plug from the bottom of the radiator. 5. Loosen the bleeder plug on top of the radiator.
Main Menu Table of Contents Cooling System 7. Loosen the drain plugs on the engine. 8. When the coolant stops draining, tighten the engine drain plugs, reinstall the plugs in the coolant pipes, and reinstall the radiator drain plug. DRAIN PLUG DRAIN PLUG 6. Remove the drain plugs from the coolant pipes under the car. DRAIN PLUG 9. Mix the recommended antifreeze with an equal amount of purified or distilled water in a clean container. The cooling system capacity is: 3.17 US gal (12.0 l ,2.
Main Menu Table of Contents Cooling System BLEEDER CAP 10. Remove the bleeder cap from the top of the heater inlet. Maintenance BLEEDER BOLT 11. Loosen the bleeder bolt on top of the engine. BLEEDER BOLT 12. Loosen the bleeder bolt near the expansion tank.
Main Menu Table of Contents Cooling System 13. Pour coolant into the expansion tank. Coolant will go through the tank into the system. When the tank is full, go to each of the four bleeders. Close each bleeder when coolant comes out of it in a steady stream with no bubbles. You may need to refill the expansion tank. EXPANSION TANK CAP 15. Turn off the engine. Check the expansion tank and, if needed, add coolant to bring it up to the MAX line. Tighten the expansion tank cap.
Main Menu Table of Contents Windshield Washers 3. Read the fluid level on the tube. If the fluid level is near the "E" mark, fill the reservoir with windshield washer fluid up to the brim. RESERVOIR CAP Fill the reservoir with a good-quality windshield washer fluid. This increases the cleaning capability and prevents freezing in cold weather. NOTICE Check the level in the windshield washer reservoir at least monthly during normal usage.
Main Menu Table of Contents Transmission Fluid Automatic Transmission DIPSTICK Check the fluid level with the engine at normal operating temperature. 1. Park the car on level ground. Shut off the engine. 2. Remove the dipstick (yellow loop) from the transmission and wipe it with a clean cloth. UPPER MARK LOWER MARK 3. Insert the dipstick into the transmission. Make sure the notch in the rubber cap fits in the dipstick guide and that you push the dipstick in all the way. 4.
Main Menu Table of Contents Transmission Fluid 6-speed Manual Transmission FILLER BOLT CORRECT LEVEL Check the fluid level with the transmission at normal operating temperature and the car sitting on level ground. Remove the transmission filler bolt and carefully feel inside the bolt hole with your finger. The fluid level should be up to the edge of the bolt hole. If it is not, add Genuine Honda Manual Transmission Fluid (MTF) until it starts to run out of the hole.
Main Menu Table of Contents Brake and Clutch Fluid Check the fluid level in the reservoirs monthly. There are two reservoirs. They are: Brake fluid reservoir (all models) Clutch fluid reservoir (manual transmission only) The brake fluid should be replaced according to the time and distance recommendations in the maintenance schedule. Brake Fluid Always use Genuine Honda DOT 3 brake fluid.
Main Menu Table of Contents Brake and Clutch Fluid Clutch System M AX M IN The fluid should be between the MIN and MAX marks on the side of the reservoir. If it is not, add brake fluid to bring it up to that level. Use the same fluid specified for the brake system. Low fluid level can indicate a leak in the clutch system. Have this system inspected as soon as possible.
Main Menu Table of Contents Air Cleaner Element The air cleaner element should be cleaned or replaced according to the time and distance recommendations in the maintenance schedule. Replacement SCREWS Cleaning (Severe Conditions) Clean the air cleaner element by blowing compressed air through it in the opposite direction to normal air flow. If you do not have access to compressed air (such as a service station), ask your Acura dealer to do this service.
Main Menu Table of Contents Air Cleaner Element, Fuel Filter 5. Install the new air cleaner element, making sure the rubber seal fits on all four sides. 6. Reinstall the air cleaner housing cover. Tighten the six screws. 7. Slide the air intake tube onto the air cleaner housing cover. Tighten the hose clamp. AIR CLEANER ELEMENT 4. Remove the old air cleaner element. Carefully clean the inside of the air cleaner housing with a damp rag. Maintenance 8.
Main Menu Table of Contents Hood Latch, Spark Plugs Hood Latch Spark Plugs The spark plugs in your car are a special platinum-tipped design for longer life. They only need to be replaced every 7 years or 105,000 miles (168,000 km), whichever comes first. Replacement 10 mm CAP NUTS 10 mm BOLTS PIVOTS COVER Clean the hood latch assembly with a mild cleaner, then lubricate it with a multipurpose grease. Lubricate all the moving parts, including the pivot.
Main Menu Table of Contents Spark Plugs IGNITION COIL 10 mm BOLT 2. Disconnect the three ignition coils from the wire harness by squeezing the harness end of each connector and pulling. 3. Remove the two 10 mm bolts holding the ignition coil. Remove the ignition coil by pulling it straight out as you twist it slightly. Maintenance SPARK PLUG SOCKET 4. Remove the spark plug with a five-eighths inch (16 mm) spark plug socket. 5. Put the new spark plug into the socket; then screw it into the hole.
Main Menu Table of Contents Spark Plugs NOTICE Tighten the spark plugs carefully. A spark plug that is too loose can overheat and damage the engine. Overtightening can cause damage to the threads in the cylinder head. Specifications: NGK: PFR6L-11 DENSO: PK20PR-L11 Spark Plug Gap: 0.04 in (1.1 mm ) 7. Install the ignition coil. Install and tighten the two hold-down bolts to: Tightening torque: 9 lbf.ft (12 N.m , 1.2 kgf.m) 6. Torque the spark plug.
Main Menu Table of Contents Battery Check the condition of your car's battery monthly. You should check the color of the test indicator window, and for corrosion on the terminals. Check the battery terminals for corrosion (a white or yellowish powder). To remove it, cover the terminals with a solution of baking soda and water. It will bubble up and turn brown. When this stops, wash it off with plain water. Dry off the battery with a cloth or paper towel.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２ Battery If you need to connect the battery to a charger, disconnect both cables to prevent damage to the car's electrical system. The battery gives off explosive hydrogen gas during normal operation. A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you. If the terminals are severely corroded, clean them with baking soda and water. Then use a wrench to loosen and remove the cables from the terminals.
Main Menu Table of Contents Battery If you need to charge the battery after storing the car, make sure you do it outside the car. Do not connect a battery charger to the jump start terminal in the engine compartment fuse box. Disconnect the terminals to prevent damage to the car's electrical system, and remove the battery from the front compartment so hydrogen gas does not build up during charging. You need to remove the spare tire holder before removing the battery.
Main Menu Table of Contents Wiper Blades Check the condition of the wiper blades at least every six months. Look for signs of cracking in the rubber, or areas that are getting hard. Replace the blades if you find these signs, or they leave streaks and unwiped areas when used. LOCK TAB To replace the blade: 1. Turn the ignition ON (II), switch the wipers to INT or — (low position), then turn the ignition OFF when the wiper arm is approximately midway in its travel. 2.
Main Menu Table of Contents Wiper Blades BLADE 5. Slide the new wiper blade into the holder until the tabs lock. 6. Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place. 7. Turn the ignition switch ON (II) and return the windshield wipers to their park position. REINFORCEMENT 3. Remove the blade from its holder by grasping the tabbed end of the blade. Pull firmly until the tabs come out of the holder. Maintenance 4. Examine the new wiper blades.
Main Menu Table of Contents Air Conditioning System Your car's air conditioning is a sealed system. Any major maintenance, such as recharging, should be done by a qualified mechanic. You can do a couple of things to make sure the air conditioning works efficiently. Periodically check the engine's radiator and air conditioning condenser for leaves, insects, and dirt stuck to the front surface. These block the air flow and reduce cooling efficiency.
Main Menu Table of Contents Drive Belts, Timing Belt Drive Belts ALTERNATOR BELT The belts should have the following "play" or deflection. Alternator belt: 0.4 — 0.53 in (11 — 13.5 mm) Compressor belt: 0.4 — 0.5 in (10 — 12 mm) If you see signs of wear or looseness, have your dealer adjust or replace the belts. COMPRESSOR BELT You should check the condition of the two engine belts every 2 years. Examine the edges of each belt for cracks or fraying.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Tires To safely operate your car, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated. The following pages give more detailed information on how and when to check air pressure, how to inspect your tires for damage and wear, and what to do when your tires need to be replaced.
Main Menu Table of Contents Tires Use a gauge to measure the air pressure at least once a month. Even tires that are in good condition may lose one to two psi (10 to 20 kPa, 0.1 to 0.2 kgf/cm 2 ) per month. Remember to check the spare tire at the same time you check all the other tires. Check the pressure in the tires when they are cold. This means the car has been parked for at least three hours.
Main Menu Table of Contents Tires Tubeless tires have some ability to self-seal if they are punctured. However, because leakage is often very slow, you should look closely for punctures if a tire starts losing pressure. Inspection Every time you check inflation, you should also examine the tires for damage, foreign objects, and wear. You should look for: INDICATOR LOCATION MARKS Bumps or bulges in the tread or side of the tire. Replace the tire if you find either of these conditions.
Main Menu Table of Contents Tires Maintenance In addition to proper inflation, correct wheel alignment helps to decrease tire wear. If you find a tire is worn unevenly, have your dealer check the wheel alignment. The tires were properly balanced by the factory. They may need to be rebalanced at some time before they are worn out. Have your dealer check the tires if you feel a consistent vibration while driving. A tire should always be rebalanced if it is removed from the wheel for repair.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Tires The tire mileage you can expect from your NSX is the same as comparable mid-and rear-engined sports cars, and it will vary greatly with your driving habits. If you drive moderately, the rear tires could last more than 10,000 miles (16,000 km). However, the mileage will be substantially less if you tend to drive your NSX at the upper limits of its capabilities.
Main Menu Table of Contents Tires The ABS works by comparing the speed of the wheels. When replacing tires, use the same size originally supplied with the car. Tire size and construction can affect wheel speed and may cause the system to work inconsistently. If you ever need to replace a wheel, make sure the wheel's specifications match those of the original wheel that came on your car. Replacement wheels are available at your Acura dealer.
Main Menu Table of Contents Tires Snow Tires If you mount snow tires on your Acura, make sure they are radial tires of the same size and load range as the original tires. Mount snow tires on all four wheels to balance your car's handling in all weather conditions. Keep in mind the traction provided by snow tires on dry roads may not be as high as your car's original equipment tires. You should drive cautiously even when the roads are clear. Check with the tire dealer for maximum speed recommendations.
Main Menu Table of Contents Lights Check the operation of your car's exterior lights at least once a month. A burned out bulb can create an unsafe condition by reducing your car's visibility and the ability to signal your intentions to other drivers.
Main Menu Table of Contents Lights Check the following: BRAKE/TAILLIGHT BACK-UP LIGHT Headlights (low and high beam) Parking lights Taillights Brake lights Turn signals Back-up lights Hazard light function License plate light Side marker lights Daytime running lights (Canadian cars) If you find any bulbs are burned out, replace them as soon as possible. Refer to the chart on page 273 to determine what type of replacement bulb is needed.
Main Menu Table of Contents Lights Replacing a Headlight Bulb Your car has halogen headlight and fog light bulbs. When replacing a bulb, handle it by its steel base and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth. NOTICE Halogen headlight bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter. 1.
Main Menu Table of Contents Lights 5. Push the edge of the hold-down spring and turn counterclockwise. BULB 6. Insert the new bulb into the socket, making sure all the tabs are in place. 7. Reinstall the hold-down spring. COVER CONNECTOR HOLD-DOWN SPRING 8. Push the electrical connector back onto the bulb. Make sure it is on all the way. 3. Remove the cover from the back of the burned-out bulb by turning it counterclockwise. 9. Replace the bulb cover.
Main Menu Table of Contents Lights Replacing Front Turn Signal and Parking Light Bulbs 5. Install the new bulb in the socket. 6. Push the bulb holder into the turn signal assembly and turn if clockwise until it locks. 7. Reconnect the electrical connector to the bulb holder. 8. Test the lights to make sure the new bulb is working. 9. Put the turn signal assembly into the bumper. Install and tighten the mounting screw. 1.
Main Menu Table of Contents Lights Replacing Side Marker Bulbs 5. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. RUBBER SEAL 6. Put the socket back into its hole in the lens and turn it clockwise until it locks. 7. Plug the wire harness back into the bulb holder. FLAT BLADE SCREWDRIVER 1. Use your fingernail to lift the rubber seal along the back edge of the side marker lens. 2.
Main Menu Table of Contents Lights Replacing Rear Bulbs 4. If the turn signal light bulb, backup bulb, or tail/stoplight bulb is burned out, remove it by pushing it in and turning counterclockwise. If the taillight bulb is burned out, remove it by pulling it straight out of its socket. 5. Install the new bulb in the socket in the reverse order of removal. The bulbs for the taillights, tail/stoplights, rear turn signals, and back-up lights are behind the trunk liner. 1.
Main Menu Table of Contents Lights Replacing a Rear License Bulb 4. Install the new bulb in the socket. 5. Turn on the parking lights and make sure the new bulb is working. Reinstall the license plate assembly on the bumper bracket with the same two screws. 1. Use a Phillips-head screwdriver to remove the two screws holding the license plate light assembly to the bracket. Pull the assembly away from the bracket. 2.
Main Menu Table of Contents Lights Replacing Bulbs in the Interior Courtesy Lights The courtesy lights in the doors, roof and under the dashboard come apart the same way. They do not all use the same bulb. DOOR 1. Remove the lens by carefully prying on the edge with your fingernail or a small flat-tip screwdriver. The two lenses on the roof-mounted interior light come out as a unit. Maintenance FOOTWELL 2. Remove the bulb by pulling it straight out of its metal tabs. 3.
Main Menu Table of Contents Lights On cars with removable roof (NSX-T) INTERIOR On the fixed roof model (Except NSX-T) INTERIOR TRUNK Maintenance
Main Menu Table of Contents Storing Your Car If you need to park your car for an extended period (more than one month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your car back on the road. If possible, store your car indoors. Block the rear wheels. If the car is to be stored for a longer period, it should be supported on jackstands so the tires are off the ground.
Main Menu Appearance Care Regular cleaning and polishing of your Acura helps to keep it "new" looking. This section gives you hints on how to clean your car and preserve its appearance: the paint, brightwork, wheels and interior. Also included are several things you can do to help prevent corrosion. Exterior Care.................................. 226 Washing...................................... 226 Power Antenna Cleaning.......... 227 Waxing........................................227 Aluminum Wheels......
Main Menu Table of Contents Exterior Care NOTICE NOTICE Although the exterior panels on your NSX are made of hardened aluminum, they may dent more easily than steel under some conditions. Exercise care when leaning on or over any part of the body. Chemical solvents and strong cleaners can damage the paint, metal, and plastic on your car. Washing Frequent washing helps preserve your car's beauty. Dirt and grit can scratch the paint, while tree sap and bird droppings can permanently ruin the finish.
Main Menu Table of Contents Exterior Care Power Antenna Cleaning Twice a year, clean the antenna mast with a dry cloth and mild detergent. Scrub the antenna in upward strokes to avoid bending it. Rinse with water. Make sure the antenna works smoothly by turning the stereo off and on several times with the ignition switch ON (II). The antenna does not need lubricating. If you use a "drive-through" car wash, make sure you turn the stereo off first.
Main Menu Table of Contents Exterior Care Aluminum Wheels Clean your Acura's aluminum alloy wheels as you do the rest of the exterior. Wash them with the same solution, and rinse them thoroughly. The wheels have a protective clearcoat that keeps the aluminum from corroding and tarnishing. Using harsh chemicals, including some commercial wheel cleaners, or stiff brushes can damage this clear-coat. Only use a mild detergent and soft brush or sponge to clean the wheels.
Main Menu Table of Contents Interior Care Carpeting Vacuum the carpeting frequently to remove dirt. Ground-in dirt will make the carpet wear out faster. Periodically shampoo the carpet to keep it looking new. Use one of the foam-type carpet cleaners on the market. Follow the instructions that come with the cleaner, applying it with a sponge or soft brush. Keep the carpeting as dry as possible by not adding water to the foam. Fabric Vacuum dirt and dust out of the material frequently.
Main Menu Table of Contents Interior Care, Corrosion Protection Windows Clean the windows, inside and out, with a commercially-available glass cleaner. You can also use a mixture of one part white vinegar to ten parts water. This will remove the haze that builds up on the inside of the windows. Use a soft cloth or paper towels to clean all glass and clear plastic surfaces. NOTICE The rear window defogger and antenna wires are bonded to the inside of the glass.
Main Menu Table of Contents Corrosion Protection, Body Repairs Many corrosion-preventive measures are built into your Acura. You can help keep your car from corroding by performing some simple periodic maintenance: Repair chips and scratches in the paint as soon as you discover them. Inspect and clean out the drain holes in the bottom of the doors and body. Use a high-pressure spray to clean the underside of your car. This is especially important in areas that use road salt in winter.
Main Menu Table of Contents Body Repairs Make sure the repair facility uses Genuine Acura replacement body parts. Some companies make sheet metal pieces that seem to duplicate the original Acura body parts, but are actually inferior in fit, finish, and corrosion resistance. Once installed, they do not give the same highquality appearance. Appearance Care Inspect areas of the body that have been repaired rather than replaced. Try to look at the inside surfaces.
Main Menu Taking Care of the Unexpected This section covers the morecommon problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your car towed. Changing a Flat Tire ..................... 234 If Your Engine Won't Start...........
Main Menu Table of Contents Changing a Flat Tire If you have a flat tire while driving, stop in a safe place to change it. Stopping in traffic or on the shoulder of a busy１６：１１：０９ road is dangerous. Drive ０３／０７／１０ ３１Ｓ５Ａ９３０ slowly along the shoulder until you get to an exit or an area to stop that is far away from the traffic lanes. FOLDING SPARE TIRE ００２１ The car can easily roll off the jack, seriously injuring anyone underneath.
Main Menu Table of Contents Changing a Flat Tire WHEEL WRENCH JACK AIR PUMP The radiator's electric fan runs automatically, even with the ignition off. The fan's blades can injure you. Keep your hands, arms, and clothing away from the fan when removing the spare tire. AIR PUMP PRESSURE GAUGE SCREWDRIVER EXTENSION 4. Open the trunk (see page 70).Lift the cover; remove the jack, wheel wrench, extension, air pump, pressure gauge, and screwdriver from the trunk.
Main Menu Table of Contents Changing a Flat Tire WHEEL NUTS CIGARETTE LIGHTER JACKING POINT POWER CORD 6. Remove the cigarette lighter from its socket and plug the power cord end into the socket. Make sure the key is in the ignition switch at LOCK (0). Taking Care of the Unexpected 7. Loosen the five wheel nuts 1/2 turn with the wheel wrench. 8. Locate the jacking point nearest the tire you need to change. It is pointed to by an arrow molded into the underside of the body.
Main Menu Table of Contents Changing a Flat Tire NOTICE WHEEL WRENCH Garage-type floor jacks and jacks of similar design can damage your car 's underbody, even if they are located on the jacking point. Only use the scissors jack that comes with your NSX to raise the car. EXTENSION 9. Use the extension and wheel wrench as shown to raise the car until the flat tire is off the ground. 10. Remove the wheel nuts and flat tire.
Main Menu Table of Contents Changing a Flat Tire FOLDING SPARE TIRE BRAKE HUB 11. Before you put on the folding spare tire, wipe any dirt off the mounting surface of the wheel and hub with a clean cloth. This will assure a tight, even contact between the wheel and hub. Taking Care of the Unexpected 12. Put on the folding spare tire with the air valve toward the bottom.
Main Menu Table of Contents Changing a Flat Tire NOTICE VALVE CAP Do not climb into the car when it is on the jack. You could cause the car to roll off the jack, damaging the suspension and body. Keep your fingers and clothing away as the tire inflates and unfolds from its compact size. 13. Unscrew the valve cap from the folding spare tire's air valve by turning it counterclockwise. Then screw on the air pump hose. 14. Reach into the car and turn the ignition switch to ACCESSORY (I).
Main Menu Table of Contents Changing a Flat Tire 15. After about five minutes, unscrew the air pump hose and check the pressure with the supplied pressure gauge. Inflate to: Front: 26 psi (180 kPa , 1.8 kgf/cm2) Rear: 32 psi (220 kPa , 2.2 kgf/cm2) Taking Care of the Unexpected 16. When finished, reach in and turn the ignition switch to LOCK (0). Unplug the air pump power cord. 17. Screw the valve cap on the valve tightly with your hands.
Main Menu Table of Contents Changing a Flat Tire 18. Lower the car to the ground and remove the jack. 19. Tighten the wheel nuts securely in the same crisscross pattern. Have the wheel nut torque checked at the nearest automotive service facility. 20. Store the jack, wheel wrench, extension, air pump, pressure gauge, screwdriver, and flat tire in the trunk. Tighten the wheel nuts to: 80 lbf.ft (108 N.m , 11 kgf.
Main Menu Table of Contents Changing a Flat Tire Storing the Folding Spare Tire Before returning the folding spare tire to its compartment, you must let out all the air. It will fold back to its original space saving shape. To store the flat tire, put a sheet of paper on the contact surface of the tire and the trunk well as shown in the illustration. Slide the tire in the trunk well with the outside surface of the aluminum wheel facing up.
Main Menu Table of Contents Changing a Flat Tire Keep your fingers and clothing away as the tire deflates and folds back to its compact size. 2. Unscrew and remove the folding spare tire valve cap. 3. Remove the rubber cover on top of the valve cap. Use the notch on the valve cap to unscrew the spare tire valve core until the air starts coming out. Use your hand to shield your eyes. The valve core can fly out under pressure.
Main Menu Table of Contents Changing a Flat Tire VALVE CAP 4. As the tire deflates, it will fold back to its original shape. When the air stops coming out of the tire, use the notch on the valve cap to tighten the valve core. Taking Care of the Unexpected 5. Put the rubber cap back on the valve cap. Screw the valve cap back on the folding spare tire valve. 6. Remove the folding spare tire and install the original tire and wheel nuts.
Main Menu Table of Contents Changing a Flat Tire Air Pump The air pump that comes with your NSX is designed specifically to inflate the folding spare tire. Follow these precautions: Connect the air pump only to a 12 V car battery. Connecting it to any other power source could damage the air pump. Applying oil to any component of the air pump is not necessary. 7. Store the folding spare tire in the front compartment with the outside surface of the wheel contacting the bracket of the spare tire well.
Main Menu Table of Contents Changing a Flat Tire This tire gives a harsher ride and less traction on some road surfaces than the regular tire. Use greater caution while driving on this tire. The wheel of the folding spare tire is designed especially to fit your car. Do not use your spare tire on another car unless it is the same make and model. The spare tire is smaller than the regular tire, reducing your car's ground clearance.
Main Menu Table of Contents If Your Engine Won't Start Diagnosing why your engine won't start falls into two areas, depending on what you hear when you turn the key to START (III): You hear nothing, or almost nothing. The engine's starter motor does not operate at all, or operates very slowly. You can hear the starter motor operating normally, or the starter motor sounds like it is spinning faster than normal, but the engine does not start up and run.
Main Menu Table of Contents If Your Engine Won't Start If the headlights dim noticeably or go out when you try to start the engine, either the battery is discharged or the connections are corroded. Check the condition of the battery and terminal connections (see page 200). You can then try jump starting the car from a booster battery (see page 249).
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Jump Starting If your car's battery has run down, you may be able to start the engine by using a booster battery. Although this seems like a simple procedure, you should take several precautions. To jump start your car, follow these directions closely: A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby. Keep all sparks, open flames, and smoking materials away from the battery.
Main Menu Table of Contents Jump Starting FUSE BOX COVER JUMP START TERMINAL 3. Open the rear window and engine cover. Locate the engine compartment fuse box on the driver's side of the compartment. Remove the fuse box cover. Taking Care of the Unexpected 4. Connect one jumper cable to the positive ( + ) terminal on the booster battery. Connect the other end to the JUMP START terminal in the fuse box. 5. Connect the second jumper cable to the negative ( — ) terminal on the booster battery.
Main Menu Table of Contents Jump Starting BOOSTER BATTERY 6. If the booster battery is in another car, have an assistant start that car and run it at a fast idle. 8. Once your car is running, disconnect the negative cable from your car, then from the booster battery. Disconnect the positive cable from your car, then the booster battery. 7. Start your car. If the starter motor still operates slowly, check the jumper cable connections to make sure they have good metal-tometal contact.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ If Your Engine Overheats The pointer of your car's temperature gauge should stay in the midrange under most conditions. It may go higher if you are driving up a long steep hill on a very hot day. If it climbs to the red mark, you should determine the reason. NOTICE Driving with the temperature gauge pointer at the red mark can cause serious damage to your engine.
Main Menu Table of Contents If Your Engine Overheats 6. Look for any obvious coolant leaks, such as a split radiator hose. Everything is still extremely hot, ０３／０７／１０ so use１６：１１：０９ caution. If you ３１Ｓ５Ａ９３０ find a leak, it must be repaired before you continue driving (see Emergency Towing on page 267). Removing the expansion tank cap while the engine is hot can cause the coolant to spray out, seriously scalding you. 7.
Main Menu Table of Contents If Your Engine Overheats 10. Start the engine and set the climate control to FULL AUTO at 90°F (32°C). Add coolant up to the MAX line on the expansion tank. If you do not have the proper coolant mixture available, you can add plain water. Remember to have the cooling system drained and refilled with the proper mixture as soon as you can. Taking Care of the Unexpected 11. Put the expansion tank cap back on tightly. Run the engine and watch the temperature gauge.
Main Menu Table of Contents Low Oil Pressure Indicator LOW OIL PRESSURE INDICATOR NOTICE Running the engine with low oil pressure can cause serious mechanical damage almost immediately. Turn off the engine as soon as you can safely get the car stopped. 4. Start the engine and watch the oil pressure indicator. If the light does not go out within ten seconds, turn off the engine. There is a mechanical problem that needs to be repaired before you can continue driving. (See Emergency Towing on page 267.
Main Menu Table of Contents Charging System Indicator CHARGING SYSTEM INDICATOR This indicator should come on when the ignition switch is ON (II), and go out after the engine starts. If it comes on brightly when the engine is running, it indicates that the charging system has stopped charging the battery. Taking Care of the Unexpected Immediately turn off all electrical accessories: radio, climate control, rear defogger, cruise control, etc.
Main Menu Table of Contents Malfunction Indicator Lamp MALFUNCTION INDICATOR LAMP This indicator comes on for a few seconds when you turn the ignition switch ON (II). If it comes on at any other time, it indicates one of the engine's emissions control systems may have a problem. Even though you may feel no difference in your car's performance, it can reduce your fuel economy and cause your car to put out excessive emissions. Continued operation may cause serious damage.
Main Menu Table of Contents Brake System Indicator BRAKE SYSTEM INDICATOR The Brake System Indicator light comes on when you turn the ignition ON (II). If the parking brake is not set, it goes off after you start the engine. If the parking brake is set, it goes off when you fully release the parking brake with the engine running. Taking Care of the Unexpected If it comes on at any other time, it indicates a problem with the car's brake system.
Main Menu Table of Contents Getting the Headlights to Pop Up If both headlights don't pop up when you turn them on, try the headlight motor button on the dashboard (see page 57 ). If one or both headlights are still down, do the following: PLASTIC CAP 1. Check the fuses for the headlight doors in the under-hood fuse box (see page 264). If you find a blown fuse, replace it with a spare fuse and try the headlights. 2.
Main Menu Table of Contents Fuses All the electrical circuits in your car have fuses to protect them from a short circuit or overload. These fuses are located in three fuse boxes.
Main Menu Table of Contents Fuses UNDER-HOOD ENGINE Push INTERIOR Push Turn The under-hood fuse box is located in the front of the engine compartment on the passenger's side. To open it, push the tab as shown. The engine compartment fuse box is located next to the air cleaner housing. To open, push the tab as shown. The interior fuse box is underneath the dashboard on the driver's side. To open it, turn the knob as shown.
Main Menu Table of Contents Fuses Checking and Replacing Fuses If something electrical in your car stops working, the first thing you should check for is a blown fuse. Determine from the chart on pages 264 and 265, or the diagram on the fuse box lid, which fuse or fuses control that component. Check those fuses first, but check all the fuses before deciding that a blown fuse is not the cause. Replace any blown fuses and check the component's operation. 1. Turn the ignition switch to LOCK (0).
Main Menu Table of Contents Fuses BLOWN 5. Look for a burned wire inside the fuse. If it is burned, replace it with one of the spare fuses of the same rating or lower. If you cannot drive the car without fixing the problem, and you do not have a spare fuse, take a fuse of the same rating or a lower rating from one of the other circuits. Make sure you can do without that circuit temporarily (such as the cigarette lighter or radio).
Main Menu Table of Contents Fuses UNDER-HOOD FUSE BOX * Taking Care of the Unexpected : Canadian Model
Main Menu Table of Contents Fuses ENGINE COMPARTMENT FUSE BOX INTERIOR FUSE BOX : Spare Fuse * : Canadian Model Taking Care of the Unexpected
Main Menu Table of Contents If Your Car Gets Stuck If your car gets stuck in sand, mud, or snow, call a towing service to pull it out (see page 267). NOTICE "Rocking'' your car between forward and reverse gear or revving up the engine and allowing the wheels to spin freely at high speeds can damage the automatic transmission. Use a tow service to prevent transmission damage.
Main Menu Table of Contents Towing If your car needs to be towed, call a professional towing service or, if you belong to one, an organization that provides roadside assistance. Never tow your car behind another vehicle with just a rope or chain. It is very dangerous. Emergency Towing There are three popular methods of towing a car: Wheel Lift Equipment — The tow truck uses two pivoting arms that go under the tires (front or rear) and lift them off the ground. The other two wheels remain on the ground.
Main Menu Table of Contents Towing If your NSX cannot be transported by flat-bed, it should be towed with the rear wheels off the ground. If, due to damage, your car must be towed with the rear wheels on the ground, do the following: 6-speed Manual Transmission Release the parking brake. Shift the transmission to Neutral. Automatic Transmission Release the parking brake. Start the engine. Shift to D, then to N. Turn off the engine.
Main Menu Technical Information The diagrams in this section give you the dimensions and capacities of your Acura, and the locations of the identification numbers. The explanations of several electronic and mechanical systems on your Acura are for the more technically-oriented owner. Identification Numbers................. 270 Specifications................................. 272 Traction Control System............... 274 DOT Tire Quality Grading........... 275 Treadwear..................................
Main Menu Table of Contents Identification Numbers Your car has several identifying numbers located in various places. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is the 17-digit number your Acura dealer uses to register your car for warranty purposes. It is also necessary for licensing and insuring your car. The easiest place to find the VIN is on a plate fastened to the top of the dashboard. You can see it by looking through the windshield on the driver's side.
Main Menu Table of Contents Identification Numbers The Engine Number is stamped on the back left corner of the engine block, below the rear valve cover. TRANSMISSION NUMBER The Transmission Number is on a label on top of the transmission.
Main Menu Table of Contents Specifications page 199. * 1 : 3.0 model (4 AT) * 2 : 3.2 model (6 MT) *1 * Technical Information : Including the coolant in the expansion tank and that remaining in the engine. Expansion tank capacity: 0.55 US gal (2.1 l ,0.46 Imp gal) 2 : Excluding the oil remaining in the engine.
Main Menu Table of Contents Specifications page 264 page 265 page 265 Technical Information
Main Menu Table of Contents Traction Control System The Traction Control System (TCS) monitors how fast the wheels are turning during acceleration. If one drive wheel is turning faster than the other, or both drive wheels are turning faster than the non-driven wheels, engine power is reduced to increase traction. The TCS uses the same wheel speed sensor assemblies as the ABS. An additional sensor measures steering wheel angle, while another sensor measures lateral acceleration (cornering force).
Main Menu Table of Contents DOT Tire Quality Grading (U.S. Vehicles) The tires on your vehicle meet all U.S. Federal Safety Requirements. All tires are also graded for treadwear, traction, and temperature performance according to Department of Transportation (DOT) standards. The following explains these gradings. Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between the tread shoulder and the maximum section width.
Main Menu Table of Contents DOT Tire Quality Grading (U.S. Vehicles) Temperature The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Main Menu Table of Contents Oxygenated Fuels Some conventional gasolines are being blended with alcohol or an ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards, some areas of the United States and Canada use oxygenated fuels to help reduce emissions. If you use an oxygenated fuel, be sure it is unleaded and meets the minimum octane rating requirement. Before using an oxygenated fuel, try to confirm the fuel's contents.
Main Menu Table of Contents Driving in Foreign Countries If you are planning to take your Acura outside the U.S. or Canada, contact the tourist bureaus in the areas you will be traveling in to find out about the availability of unleaded gasoline with the proper octane rating. If unleaded gasoline is not available, be aware that using leaded gasoline in your Acura will affect performance and fuel mileage, and damage its emissions controls. It will no longer comply with U.S.
Main Menu Table of Contents Emissions Controls The burning of gasoline in your car's engine produces several byproducts. Some of these are carbon monoxide (CO), oxides of nitrogen (NOx) and hydrocarbons (HC). Gasoline evaporating from the tank also produces hydrocarbons. Controlling the production of NOx, CO, and HC is important to the environment. Under certain conditions of sunlight and climate, NOx and HC react to form photochemical "smog.
Main Menu Table of Contents Emissions Controls Exhaust Emissions Controls The exhaust emissions controls include four systems: PGM-FI, Ignition Timing Control, Exhaust Gas Recirculation and Three Way Catalytic Converter. These four systems work together to control the engine's combustion and minimize the amount of HC, CO, and NOx that comes out the tailpipe. The exhaust emissions control systems are separate from the crankcase and evaporative emissions control systems.
Main Menu Table of Contents Three Way Catalytic Converter The three way catalytic converter contains precious metals that serve as catalysts, promoting chemical reactions to convert the exhaust gasses without affecting the metals. The catalytic converter is referred to as a three-way catalyst, since it acts on HC, CO, and NOx. A replacement unit must be an original Acura part or its equivalent. The three way catalytic converter must operate at a high temperature for the chemical reactions to take place.
Main Menu
Main Menu Warranty and Customer Relations Customer Relations Information................................. 284 Canada Zone Office Map.............. 285 Warranty Coverages..................... 286 Reporting Safety Defects (U.S. Vehicles)...........................287 Authorized Manuals......................
Main Menu Table of Contents Customer Relations Information Acura dealership personnel are trained professionals. They should be able to answer all your questions. If you encounter a problem that your dealership does not solve to your satisfaction, please discuss it with the dealership's management. The Service Manager or General Manager can help. Almost all problems are solved in this way.
Main Menu Table of Contents Canada Zone Office Map CUSTOMER RELATIONS RELATIONS AVEC LA CLIENTELE Honda Canada Inc. 715 Milner Avenue Toronto, ON M1B 2K8 Tel: 1-888-9-ACURA-9 Fax: Toll-free 1-877-939-0909 Toronto (416) 287-4776 Honda Canada Inc.
Main Menu Table of Contents Warranty Coverages U.S. Owners Your new Acura is covered by these warranties: New Car Limited Warranty — covers your new vehicle, except for the battery, emissions control systems and accessories, against defects in materials and workmanship. Emissions Control Systems Defects Warranty and Emissions Performance Warranty — these two warranties cover your car's emissions control systems. Time, mileage, and coverage are conditional.
Main Menu Table of Contents Reporting Safety Defects (U.S. Vehicles) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Acura Automobile Division, American Honda Motor Co., Inc.
Main Menu Table of Contents
Main Menu Table of Contents Authorized Manuals Purchasing Factory Authorized Manuals (U.S. only) The following publications covering the operation and servicing of your car can be obtained from Helm Incorporated, either by filling out the attached form or, for credit card holders, calling the toll-free phone number on the form. For manuals prior to the year shown below, contact Helm Incorporated, P.O. Box 07280, Detroit, Michigan 48207, or call 1-800-782-4356. Valid only for sales within the U.S.
Main Menu Table of Contents Authorized Manuals Service Manual: This manual covers maintenance and recommended procedures for repair to engine and chassis components. It is written for the Journeyman mechanic, but is simple enough for most mechanically-inclined owners to understand. Electrical Troubleshooting Manual: This manual complements the Service Manual by providing in-depth troubleshooting information for each electrical circuit in your car.
Main Menu Index Accessories Installation.................................. 137 ACCESSORY (Ignition Key Position)........................................ 68 Adding Automatic Transmission Fluid........................................ 191 Brake Fluid................................. 193 Clutch Fluid................................194 Engine Coolant........................... 183 Engine Oil...................................179 Manual Transmission Fluid ..... 192 Windshield Washer Fluid.........
Main Menu Index Beverage Holder.............................. 86 Body Repair.................................... 231 Brakes............................................. 156 Anti-lock System (ABS)............ 157 Break-in, New Linings .............. 128 Fluid............................................ 193 Light, Burned-out...................... 220 Parking.......................................... 84 System Indicator.......................... 49 Wear Indicators, Disc ...............
Main Menu Index Cold Weather, Starting in............. 145 Compact (Folding) Spare Tire..... 245 Controls, Instruments and.............. 45 Coolant Adding.........................................183 Checking.....................................133 Proper Solution.......................... 183 Temperature Gauge.................... 53 Console Compartment.................... 85 Corrosion Protection..................... 230 Courtesy Lights............................... 88 Crankcase Emission Control System....
Main Menu Index Engine Malfunction Indicator Lamp................................. 50, 257 Oil Pressure Gauge..................... 53 Oil Pressure Indicator......... 49, 255 Oil, What Kind to Use............... 179 Overheating................................ 252 Speed Limiter.................... 147, 153 Specifications............................. 272 Engine Cover, Opening the.......... 130 Ethanol in Gasoline ....................... 277 Evaporative Emission Controls.... 279 Exhaust Fumes..................
Main Menu Index Halogen Headlight Bulbs.............. 216 Hazard Warning Flashers............... 60 Headlights Daytime Running Lights............. 56 Emergency Operation, Manual....................................259 High Beam Indicator................... 52 High Beams, Turning on............ 56 Low Beams, Turning on ............. 56 Reminder Chime.......................... 56 Replacing Halogen Bulbs ......... 216 Turning on.................................... 56 Heating and Air Conditioning System.......
Main Menu Index Locks Anti-theft Steering Column........ 68 Fuel Fill Door............................. 129 Glove Box..................................... 71 Power Door.................................. 69 Trunk............................................ 70 Low Coolant Level......................... 133 Lower Gear, Downshifting to a.... 146 Low Fuel Indicator .......................... 52 Low Oil Pressure Indicator.... 49, 255 Lubricant Specifications Chart.... 272 Luggage.................................
Main Menu Index Protecting Adults............................. 12 Additional Safety Precautions.... 18 Advice for Pregnant Women...... 17 Protecting Children......................... 19 Protecting Larger Children........ 29 Protecting Small Children.......... 26 Using Child Seats with Tethers......................................32 Radiator Overheating.................... 252 Radio/Cassette Sound System .... 100 Rear End Towing........................... 267 Rear Lights, Bulb Replacement...
Main Menu Index Shift Lever Position Indicator...... 149 Shift Lock Release......................... 154 Side Marker Lights, Bulb Replacement in.......................... 219 Signaling Turns................................ 58 6-speed Manual Transmission Checking Fluid Level................ 192 Shifting the................................. 146 Snow Tires...................................... 213 Solvent-type Cleaners.................... 226 Sound System.................................
Main Menu Index Specifications............................. 273 Technical Information.............. 269 Tools,Tire Changing.................... 235 Towing A Trailer, Do Not....................... 163 Emergency Wrecker................. 267 Traction Control System (TCS) Operation.................................... 160 Technical Description............... 274 Trailer, Do Not Tow a...................163 Transmission Checking Fluid Level, Automatic...............................
Main Menu Index Windows Cleaning...................................... 230 Operating the Power................... 73 Opening the Rear....................... 130 Rear, Defogger............................ 57 Windshield Cleaning........................................ 60 Defroster...................................... 97 Wipers, Windshield Changing Blades........................ 203 Operation...................................... 59 Worn Tires.....................................
Main Menu Service Information Summary Gasoline: Premium unleaded gasoline, pump octane number of 91 or higher. Fuel Tank Capacity: 18.5 US gal (70 l ,15.4 Imp gal) Recommended Engine Oil: API Service SJ "Energy Conserving" oil, SAE 10W-30 viscosity (see page 179). Oil change capacity (including filter): 5.3 US qt (5.0 l ,4.4 Imp qt) Automatic Transmission Fluid: Honda Premium Formula Automatic Transmission Fluid preferred, or a DEXRON® III ATF as a temporary replacement (see page 191).
