Introduction Congratulations! Your selection of a 2010 Acura TSX was a wise investment. It will give you years of driving pleasure. One of the best ways to enhance the enjoyment of your new vehicle is to read this manual. In it, you will learn how to operate its driving controls and convenience items. Afterwards, keep this owner’s manual in your vehicle so you can refer to it at any time. As you read this manual, you will find information that is preceded by a symbol.
Introduction California Proposition 65 Warning WARNING: This product contains or emits chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Event Data Recorders This vehicle is equipped with one or more devices commonly referred to as event data recorders. These devices record front seat belt use, front passenger seat occupancy, airbag deployment data, and the failure of any airbag system component.
A Few Words About Safety Your safety, and the safety of others, is very important. And operating this vehicle safely is an important responsibility. To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual. This information alerts you to potential hazards that could hurt you or others. Of course, it is not practical or possible to warn you about all the hazards associated with operating or maintaining your vehicle.
2010 TSX Online Reference Owner's Manual Contents Owner's Identification Form Your Vehicle at a Glance (main controls) ................................................................................................ 3 Driver and Passenger Safety (seat belts, SRS, and child protection) ............................................................. 5 Instruments and Controls (indicators, gauges, multi-information display, dashboard, and steering column) ........
Overview of Contents Contents A convenient reference to the sections in this manual. Your Vehicle at a Glance A quick reference to the main controls in your vehicle. Driver and Passenger Safety Important information about the proper use and care of your vehicle’s seat belts, an overview of the supplemental restraint system, and valuable information on how to protect children with child restraints.
Your Vehicle at a Glance MULTI-INFORMATION DISPLAY (P.70) MOONROOF SWITCH (P.151) MIRROR CONTROLS (P.145) Your Vehicle at a Glance DRIVER’S FRONT AIRBAG (P.9) HOMELINK BUTTONS (P.301) PASSENGER’S FRONT AIRBAG(P.9) DRIVING POSITION MEMORY SYSTEM BUTTONS＊ (P.142) AUDIO SYSTEM (P.174) CLOCK＊ (P.289) COMPASS＊ (P.294) POWER DOOR LOCK MASTER SWITCH (Unlocking Fuel Fill Door) (P.124) POWER WINDOW SWITCHES (P.147) HAZARD WARNING BUTTON (P.117) CLIMATE CONTROL SYSTEM (P.166) TRUNK RELEASE BUTTON(P.
Your Vehicle at a Glance HEADLIGHTS/TURN SIGNALS (P.111)/ FOG LIGHTS＊3 (P.115) INSTRUMENT PANEL BRIGHTNESS(P.115) WINDSHIELD WIPERS/ WASHERS (P.110) PASSENGER AIRBAG OFF INDICATOR (P.33) CENTER DISPLAY＊2 REMOTE AUDIO CONTROL BUTTONS (P.286) INTERFACE DIAL＊2 (P.222) SELECTOR KNOB＊3 (P.175) VEHICLE STABILITY ASSIST (VSA) SYSTEM OFF SWITCH (P.393) HAZARD WARNING BUTTON (P.117) REAR WINDOW DEFOGGER/HEATED MIRROR BUTTON (P.117, 146) BLUETOOTH HANDSFREELINK SYSTEM VOICE CONTROL BUTTONS (P.
Driver and Passenger Safety Important Safety Precautions .......... 6 Your Vehicle’s Safety Features........ 7 Seat Belts ........................................ 8 Airbags ............................................ 9 Protecting Adults and Teens.......... 11 1. Close and Lock the Doors ...... 11 2. Adjust the Front Seats ............ 13 3. Adjust the Seat-Backs ............. 14 4. Adjust the Head Restraints .... 14 5. Fasten and Position the Seat Belts .............................. 15 6.
Important Safety Precautions You’ll find many safety recommendations throughout this section, and throughout this manual. The recommendations on this page are the ones we consider to be the most important. Always Wear Your Seat Belt A seat belt is your best protection in all types of collisions. Airbags are designed to supplement seat belts, not replace them.
Your Vehicle’s Safety Features (10) (1) (8) (9) (7) (5) (7) (2) (8) (6) (11) (2) (1) Safety Cage (2) Crush Zones (3) Seats and Seat-Backs (4) Head Restraints (5) Collapsible Steering Column (6) Seat Belts (7) Front Airbags (8) Side Airbags (9) Side Curtain Airbags (10) Door Locks (11) Automatic Seat Belt Tensioners Some features do not require any action on your part.
Your Vehicle’s Safety Features Seat Belts Your vehicle is equipped with seat belts in all seating positions. Your seat belt system also includes an indicator on the instrument panel and a beeper to remind you and your passengers to fasten your seat belts. Why Wear Seat Belts Seat belts are the single most effective safety device for adults and larger children. (Infants and smaller children must be properly restrained in child seats.
Your Vehicle’s Safety Features Airbags Driver and Passenger Safety Your vehicle has a supplemental restraint system (SRS) with front airbags to help protect the heads and chests of the driver and a front seat passenger during a moderate to severe frontal collision (see page 25 for more information on how your front airbags work).
Your Vehicle’s Safety Features The most important things you need to know about your airbags are: Airbags do not replace seat belts. They are designed to supplement the seat belts. Airbags offer no protection in rear impacts, or minor frontal or side collisions. What you should do: Always wear your seat belt properly, and sit upright and as far back from the steering wheel as possible while allowing full control of the vehicle.
Protecting Adults and Teens See pages 36 − 54 for important guidelines on how to properly protect infants, small children, and larger children who ride in your vehicle. 1.Close and Lock the Doors After everyone has entered the vehicle, be sure the doors are closed and locked. Your vehicle has a door/ trunk open indicator (red) on the instrument panel to indicate when any door or the trunk lid is not tightly closed.
Protecting Adults and Teens Locking the doors reduces the chance of someone being thrown out of the vehicle during a crash, and it helps prevent passengers from accidentally opening a door and falling out. Locking the doors also helps prevent an outsider from unexpectedly opening a door when you come to a stop. When the trunk is not tightly closed, this indicator will come on. When one or more doors or the trunk lid are not tightly closed, the corresponding indicator for each condition will come on.
Protecting Adults and Teens 2.Adjust the Front Seats The National Highway Traffic Safety Administration and Transport Canada recommend that drivers allow at least 10 inches (25 cm) between the center of the steering wheel and the chest. In addition to adjusting the seat, you can adjust the steering wheel up and down, and in and out (see page 118 ). Sitting too close to a front airbag can result in serious injury or death if the front airbags inflate.
Protecting Adults and Teens 3.Adjust the Seat-Backs 4.Adjust the Head Restraints Reclining the seat-back too far can result in serious injury or death in a crash. Adjust the seat-back to an upright position, and sit well back in the seat. Adjust the driver’s seat-back to a comfortable, upright position, leaving ample space between your chest and the airbag cover in the center of the steering wheel. Passengers with adjustable seatbacks should also adjust their seatback to a comfortable, upright position.
Protecting Adults and Teens Make sure head restraints are in place and positioned properly before driving. Properly adjusted head restraints will help protect occupants from whiplash and other crash injuries. Position the lap part of the belt as low as possible across your hips, then pull up on the shoulder part of the belt so the lap part fits snugly. This lets your strong pelvic bones take the force of a crash and reduces the chance of internal injuries.
Protecting Adults and Teens If necessary, pull up on the belt again to remove any slack, then check that the belt rests across the center of your chest and over your shoulder. RELEASE BUTTON Never place the shoulder portion of a lap/shoulder belt under your arm or behind your back. This could cause very serious injuries in a crash. If a seat belt does not seem to work properly, it may not protect the occupant in a crash. This spreads the forces of a crash over the strongest bones in your upper body.
Protecting Adults and Teens Sitting improperly can increase the chance of injury during a crash. For example, if an occupant slouches, lies down, turns sideways, sits forward, leans forward or sideways, or puts one or both feet up, the chance of injury during a crash is greatly increased. In addition, an occupant who is out of position in the front seat can be seriously or fatally injured in a crash by striking interior parts of the vehicle or being struck by an inflating front airbag.
Protecting Adults and Teens When driving, remember to sit upright and adjust the seat as far back as possible while allowing full control of the vehicle. When riding as a front passenger, adjust the seat as far back as possible. This will reduce the risk of injuries to both you and your unborn child that can be caused by a crash or an inflating front airbag. Each time you have a checkup, ask your doctor if it’s okay for you to drive.
Additional Information About Your Seat Belts This system uses the same sensors as the front airbags to monitor whether the front seat belts are latched or unlatched, and how much weight is on the front passenger’s seat (see pages 27 and 28 ). The seat belt system includes an indicator on the instrument panel and a beeper to remind you and your passengers to fasten your seat belts.
Additional Information About Your Seat Belts If the indicator comes on or the beeper sounds when the driver’s seat belt is latched and there is no front seat passenger and no items on the front seat, something may be interfering with the monitoring system. Look for and remove: Any items under the front passenger’s seat. Any object(s) hanging on the seat or in the seat-back pocket. Any object(s) touching the rear of the seat-back. If no obstructions are found, have your vehicle checked by a dealer.
Additional Information About Your Seat Belts Automatic Seat Belt Tensioners The tensioners are designed to activate in any collision severe enough to cause the front airbags to deploy. If a side curtain airbag deploys during a side impact, the tensioner on that side of the vehicle will also deploy. To deactivate the lockable retractor, unlatch the buckle and let the seat belt fully retract. To refasten the seat belt, pull it out only as far as needed.
Additional Information About Your Seat Belts Seat Belt Maintenance For safety, you should check the condition of your seat belts regularly. Pull each belt out fully, and look for frays, cuts, burns, and wear. Check that the latches work smoothly and the belts retract easily. If a belt does not retract easily, cleaning the belt may correct the problem (see page 441 ). Any belt that is not in good condition or working properly will not provide good protection and should be replaced as soon as possible.
Additional Information About Your Airbags Airbag System Components (1) (15) (8) (9) (2) (7) (12) (11) (5) Driver and Passenger Safety (14) (8) (1) Driver’s Front Airbag (3) (2) Passenger’s Front Airbag (3) Control Unit (6) (4) Front Seat Belt Tensioners (5) Side Airbags (6) Driver’s Seat Position Sensor (7) Front Passenger’s Weight Sensors (10) (8) Front Impact Sensors (9) Passenger Airbag Off Indicator (10) Side Impact Sensors (First) (11) Occupant Position Detection System (OPDS) Sensors (12) Front P
Additional Information About Your Airbags Your airbag system includes: Two SRS (supplemental restraint system) front airbags. The driver’s airbag is stored in the center of the steering wheel; the front passenger’s airbag is stored in the dashboard. Both are marked ‘‘SRS AIRBAG’’ (see page 25 ). Two side airbags, one for the driver and one for a front passenger. The airbags are stored in the outer edges of the seatbacks. Both are marked ‘‘SIDE AIRBAG’’ (see page 29 ).
Additional Information About Your Airbags How Your Front Airbags Work Although both airbags normally inflate within a split second of each other, it is possible for only one airbag to deploy. An indicator on the instrument panel that alerts you that the passenger’s side airbag has been turned off (see page 32 ). An indicator on the dashboard that alerts you that the passenger’s front airbag has been turned off (see page 33 ).
Additional Information About Your Airbags The total time for inflation and deflation is one-tenth of a second, so fast that most occupants are not aware that the airbags deployed until they see them lying in their laps. After inflating, the front airbags immediately deflate, so they won’t interfere with the driver’s visibility, or the ability to steer or operate other controls. After a crash, you may see what looks like smoke. This is actually powder from the airbag’s surface.
Additional Information About Your Airbags Advanced Airbags Your front airbags are also advanced airbags. The main purpose of this feature is to help prevent airbagcaused injuries to short drivers and children or small-statured adults who ride in front. If the occupant’s belt is not latched, the airbag will deploy at a slightly lower threshold, because the occupant would need extra protection.
Additional Information About Your Airbags If there is a problem with the sensor, the SRS indicator will come on, and the airbag will inflate in the normal manner regardless of the driver’s seating position. Be aware that objects placed on the passenger’s seat can also cause the airbag to be turned off. PASSENGER’S SEAT WEIGHT SENSOR The passenger’s advanced front airbag system has weight sensors under the seat.
Additional Information About Your Airbags To ensure that the passenger’s advanced front airbag system will work properly, do not do anything This includes: A rear passenger pushing or pulling on the back of the front passenger’s seat. Moving the front seat or seat-back forcibly back against cargo on the seat or floor behind it. Hanging heavy items on the front passenger seat, or placing heavy items in the seat-back pocket.
Additional Information About Your Airbags Only one airbag will deploy during a side impact. If the impact is on the passenger’s side, the passenger’s side airbag will deploy even if there is no passenger. To get the best protection from the side airbags, front seat occupants should wear their seat belts and sit upright and well back in their seats. Side Airbag Cutoff System Your vehicle has a side airbag cutoff system designed primarily to protect a child riding in the front passenger’s seat.
Additional Information About Your Airbags How Your Side Curtain Airbags Work One or both side curtain airbags may inflate in a moderate to severe frontal collision which causes the front airbags to deploy. To get the best protection from the side curtain airbags, occupants should wear their seat belts and sit upright and well back in their seats. How the SRS Indicator Works The SRS indicator alerts you to a potential problem with your airbags or seat belt tensioners.
Additional Information About Your Airbags If the indicator comes on at any other time, or does not come on at all, you should have the system checked by your dealer. For example: If the SRS indicator does not come on after you turn the ignition switch to the ON (II) position. If the indicator stays on after the engine starts. U.S. Ignoring the SRS indicator can result in serious injury or death if the airbag systems or tensioners do not work properly.
Additional Information About Your Airbags How the Passenger Airbag Off Indicator Works Canada If no weight is detected on the front seat, the airbag will be automatically shut off. However, the indicator will not come on. The passenger airbag off indicator may come on and off repeatedly if the total weight on the seat is near the airbag cutoff threshold.
Additional Information About Your Airbags Airbag Service Your airbag systems are virtually maintenance free, and there are no parts you can safely service. However, you must have your vehicle serviced if: An airbag ever inflates. Any airbag that has deployed must be replaced along with the control unit and other related parts. Any seat belt tensioner that activates must also be replaced. Do not try to remove or replace any airbag by yourself.
Additional Information About Your Airbags Do not remove or modify a front seat without consulting your dealer. This could make the Driver and Passenger Safety driver’s seat position sensor or the front passenger’s weight sensors ineffective. If it is necessary to remove or modify a front seat to accommodate a person with disabilities, first contact Acura Client Services at 800-382-2238.
Protecting Children − General Guidelines All Children Must Be Restrained Each year, many children are injured or killed in vehicle crashes because they are either unrestrained or not properly restrained. In fact, vehicle accidents are the number one cause of death of children age 12 and under. Children depend on adults to protect them. However, despite their best intentions, many adults do not know how to properly protect child passengers.
Protecting Children − General Guidelines The National Highway Traffic Safety Administration and Transport Canada recommend that all children aged 12 and under be properly restrained in a back seat. Some states have laws restricting where children may ride. Children who ride in back are less likely to be injured by striking interior vehicle parts during a collision or hard braking. Also, children cannot be injured by an inflating front airbag when they ride in the back.
Protecting Children − General Guidelines To remind you of the passenger’s front airbag hazards, and that children must be properly restrained in a back seat, your vehicle has warning labels on the dashboard (U.S. models) and on the front visors. Please read and follow the instructions on these labels. U.S.
Protecting Children − General Guidelines Place the largest child in the front seat, provided the child is large enough to wear the lap/shoulder belt properly (see page 51 ). Move the vehicle seat as far to the rear as possible (see page 134 ). Have the child sit upright and well back in the seat (see page 17 ). Make sure the seat belt is properly positioned and secured (see page 15 ).
Protecting Children − General Guidelines Make sure any unused seat belt that a child can reach is buckled, the lockable retractor is activated, and the belt is fully retracted and locked. If a child wraps a loose seat belt around their neck, they can be seriously or fatally injured. (See pages 48 and 49 for how to activate and deactivate the lockable retractor.) Use the childproof door locks to prevent children from opening the rear doors. This can prevent Do not leave children alone in a vehicle.
Protecting Infants and Small Children Protecting Infants Only a rear-facing child seat provides proper support for a baby’s head, neck, and back. Do not put a rear-facing child seat in a forward-facing position. If placed facing forward, an infant could be very seriously injured during a frontal collision.
Protecting Infants and Small Children In any of these situations, we strongly recommend that you install the child seat directly behind the front passenger’s seat, move the seat as far forward as needed, and leave it unoccupied. Or, you may wish to get a smaller rear-facing child seat. Protecting Small Children Of the different seats available, we recommend those that have a fivepoint harness system as shown.
Protecting Infants and Small Children, Selecting a Child Seat If it is necessary to put a forwardfacing child seat in the front, move the vehicle seat as far to the rear as possible, and be sure the child seat is firmly secured to the vehicle and the child is properly strapped in the seat. Placing a forward-facing child seat in the front seat can result in serious injury or death if the front airbag inflates.
Selecting a Child Seat, Installing a Child Seat In seating positions and vehicles not equipped with LATCH, a LATCHcompatible child seat can be installed using a seat belt. Whatever type of seat you choose, to provide proper protection, a child seat should meet three requirements: 3. The child seat should fit the vehicle seating position (or positions) where it will be used.
Installing a Child Seat A child seat secured with a seat belt should be installed as firmly as possible. However, it does not need to be ‘‘rock solid.’’ Some side-to-side movement can be expected and should not reduce the child seat’s effectiveness. 3. Secure the child in the child seat. If the child seat is not secure, try installing it in a different seating position, or use a different style of child seat that can be firmly secured.
Installing a Child Seat Installing a Child Seat with LATCH Your vehicle is equipped with LATCH (Lower Anchors and Tethers for CHildren) at the outer rear seats. The lower anchors are located between the seat-back and seat bottom, and are to be used only with a child seat designed for use with LATCH. The location of each lower anchor is indicated by a small button above the anchor point. You can find lower anchors in the slits in the seat-backs.
Installing a Child Seat TETHER STRAP HOOK 8. Push and pull the child seat forward and from side-to-side to verify that it is secure. Flexible type Other LATCH-compatible seats have a flexible-type connector as shown above. ANCHOR 6. Route the tether strap through the legs of the head restraint and over the seat-back, making sure the strap is not twisted. 4. Whatever type you have, follow the child seat maker’s instructions for adjusting or tightening the fit. 5.
Installing a Child Seat Installing a Child Seat with a Lap/ Shoulder Belt When not using the LATCH system, all child seats must be secured to the vehicle with the lap part of a lap/ shoulder belt. In addition, the lap/shoulder belts in all seating positions except the driver’s have a lockable retractor that must be activated to secure a child seat. 1.
Installing a Child Seat 4. After confirming that the belt is locked, grab the shoulder part of the belt near the buckle, and pull up to remove any slack from the lap part of the belt. Remember, if the lap part of the belt is not tight, the child seat will not be secure. 5. Push and pull the child seat forward and from side-to-side to verify that it is secure enough to stay upright during normal driving maneuvers.
Installing a Child Seat Installing a Child Seat with a Tether Using an Anchor TETHER STRAP HOOK TETHER STRAP HOOK TETHER ANCHORAGE POINTS Outer Position ANCHOR ANCHOR Center Position ANCHOR COVER A child seat with a tether can be installed in any seating position in the back seat, using one of the anchorage points shown above. Since a tether can provide additional security to the lap/shoulder belt installation, we recommend using a tether whenever one is required or available. 1.
Protecting Larger Children When a child reaches the recommended weight or height limit for a forward-facing child seat, the child should sit in a back seat on a booster seat and wear the lap/ shoulder belt. Allowing a child age 12 or under to sit in front can result in injury or death if the passenger’s front airbag inflates.
Protecting Larger Children 3. Does the shoulder belt cross between the child’s neck and arm? Using a Booster Seat 4. Is the lap part of the belt as low as possible, touching the child’s thighs? 5. Will the child be able to stay seated like this for the whole trip? If you answer yes to all these questions, the child is ready to wear the lap/shoulder belt correctly. If you answer no to any question, the child needs to ride on a booster seat.
Protecting Larger Children A child may continue using a booster seat until the tops of their ears are even with the top of the vehicle’s or booster’s seat-back. A child of this height should be tall enough to use the lap/shoulder belt without a booster seat. When Can a Larger Child Sit in Front The National Highway Traffic Safety Administration and Transport Canada recommend that all children age 12 and under be properly restrained in a back seat.
Protecting Larger Children If you decide that a child can safely ride up front, be sure to: Carefully read the owner’s manual, and make sure you understand all seat belt instructions and all safety information. Move the vehicle seat to the rearmost position. Additional Safety Precautions Do not let a child wear a seat belt across the neck. This could result in serious neck injuries during a crash. Do not let a child put the shoulder part of a seat belt behind the back or under the arm.
Carbon Monoxide Hazard Have the exhaust system inspected for leaks whenever: Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and even kill you. Avoid any enclosed areas or activities that expose you to carbon monoxide. The vehicle is raised for an oil change. You notice a change in the sound of the exhaust. The vehicle was in a collision that may have damaged the underside. High levels of carbon monoxide can collect rapidly in enclosed areas, such as a garage.
Safety Labels These labels are in the locations shown. They warn you of potential hazards that could cause serious injury or death. Read these labels carefully. If a label comes off or becomes hard to read (except for the U.S. dashboard label which may be removed by the owner), contact your dealer for a replacement. SUN VISOR U.S. models RADIATOR CAP Canadian models DOOR JAMBS U.S. models Canadian models DASHBOARD U.S.
Instruments and Controls This section gives information about the controls and displays that contribute to the daily operation of your vehicle. All the essential controls are within easy reach. Seats ................................................ 134 Power Seat Adjustments........... 134 Driver’s Lumbar Support .......... 135 Head Restraints ......................... 135 Folding the Rear Seats .............. 138 Seat Heaters ................................... 141 Driving Position Memory System..........
Control Locations MULTI-INFORMATION DISPLAY (P.70) MOONROOF SWITCH (P.151) MIRROR CONTROLS (P.145) AUDIO SYSTEM (P.174) CLOCK＊, COMPASS＊ (P.289) (P.294) DRIVING POSITION MEMORY SYSTEM BUTTONS＊ (P.142) HAZARD WARNING BUTTON (P.117) POWER DOOR LOCK MASTER SWITCH (Unlocking Fuel Fill Door) (P.124) CLIMATE CONTROL SYSTEM (P.166) POWER WINDOW SWITCHES (P.147) ACCESSORY POWER SOCKET (P.156) TRUNK RELEASE BUTTON (P.130) HOOD RELEASE HANDLE ACCESSORY POWER (P.350) SOCKET (P.
Instrument Panel VEHICLE STABILITY ASSIST (VSA) SYSTEM INDICATOR (P.63) FOG LIGHT INDICATOR (P.66) HIGH BEAM INDICATOR (P.66) CRUISE MAIN INDICATOR (P.66) CRUISE CONTROL INDICATOR (P.66) SYSTEM MESSAGE INDICATOR (P.67) LOW TIRE PRESSURE/TPMS INDICATOR (P.64, 386) MALFUNCTION INDICATOR LAMP (P.60, 472) CHARGING SYSTEM INDICATOR (P.61, 471) SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR (P.62) ELECTRIC POWER STEERING (EPS) INDICATOR (P.65) LOW OIL PRESSURE INDICATOR (P.60, 471) SECURITY SYSTEM INDICATOR (P.
Instrument Panel Indicators The instrument panel has many indicators to give you important information about your vehicle. Seat Belt Reminder Indicator This indicator comes on when you turn the ignition switch to the ON (II) position. It reminds you and your passengers to fasten your seat belts. A beeper also sounds if you have not fastened your seat belt. You will also see a ‘‘FASTEN SEAT BELT’’ message on the multiinformation display.
Instrument Panel Indicators Immobilizer System Indicator This indicator comes on briefly when you turn the ignition switch to the ON (II) position. It will then go off if you have inserted a properly coded ignition key. If it is not a properly coded key, the indicator will blink, and the engine’s fuel system will be disabled (see page 121 ). U.S. Canada Parking Brake and Brake System Indicator This indicator has two functions: 1. It comes on when you turn the ignition switch to the ON (II) position.
Instrument Panel Indicators Anti-lock Brake System (ABS) Indicator This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position, and when the ignition switch is turned to the START (III) position. If this indicator comes on at any other time, there is a problem in the ABS. If this happens, take the vehicle to your dealer to have it checked. With this indicator on, your vehicle still has normal braking ability but no anti-lock function.
Instrument Panel Indicators If it comes on and stays on at any other time, or it does not come on when you turn the ignition switch to the ON (II) position, there is a problem with the VSA system. You will also see a ‘‘CHECK VSA SYSTEM’’ message on the multiinformation display. Take your vehicle to a dealer to have it checked. Without VSA, your vehicle still has normal driving ability, but will not have VSA traction and stability enhancement. For more information, see page 392 .
Instrument Panel Indicators Low Tire Pressure/ TPMS Indicator This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. This indicator has two functions: 1. If it comes on while driving, it indicates that one or more of your vehicle’s tires are significantly low on pressure. You will also see a ‘‘CHECK TIRE PRESSURE’’ message on the multiinformation display (see page 388 ).
Instrument Panel Indicators If this happens, stop the vehicle in a safe place and turn off the engine. Reset the system by restarting the engine. The indicator will stay on, but should go off after driving a short distance. If it does not go off, or comes back on again while driving, take the vehicle to your dealer to have it checked. With the indicator on, the EPS may be turned off, making the vehicle harder to steer.
Instrument Panel Indicators Lights On Indicator This indicator reminds you that the exterior lights are on. It comes on when the light switch is in either the or position. If you turn the ignition switch to the ACCESSORY (I) or the LOCK (0) position without turning off the light switch, this indicator will remain on. A reminder chime will also sound when you open the driver’s door.
Instrument Panel Indicators Low Fuel Indicator Most of the time, this indicator comes on along with other indicators in the instrument panel such as the seat belt reminder indicator, SRS indicator, VSA system indicator, etc. This indicator is in the fuel gauge. It comes on as a reminder that you must refuel soon. You will also see a ‘‘FUEL LOW’’ message on the multiinformation display. Security System Indicator SECURITY SYSTEM INDICATOR This indicator comes on when the security system is set.
Gauges TACHOMETER SPEEDOMETER TEMPERATURE GAUGE Fuel Gauge This shows how much fuel you have. It may show slightly more or less than the actual amount. The needle returns to the bottom after you turn off the ignition. FUEL GAUGE Avoid driving with an extremely low f uel level. Running out of f uel could cause the engine to misf ire, damaging the catalytic converter. MULTI-INFORMATION DISPLAY U.S. model is shown.
Gauges Instruments and Controls Temperature Gauge This shows the temperature of the engine’s coolant. During normal operation, the pointer should rise from the bottom mark to about the middle of the gauge. In severe driving conditions, such as very hot weather or a long period of uphill driving, the pointer may rise to the upper zone. If it reaches the red (hot) mark, pull safely to the side of the road. Turn to page 469 for instructions and precautions on checking the engine cooling system.
Multi-Information Display The multi-information display in the instrument panel displays various information and messages when the ignition switch is in the ON (II) position. Some of the messages help you operate your vehicle more comfortably. Others help to keep you aware of the periodic maintenance your vehicle needs for continued trouble-free driving. There are three types of messages: normal display messages, engine oil life and maintenance messages, and system messages.
Multi-Information Display SEL/RESET BUTTON In the multi-information display, the system message is also displayed (see page 78 ) and you can customize your vehicle control settings (see page 81 ). UPPER SEGMENT INFO BUTTONS (▲/▼) With the ignition switch in the ON (II) position, the multi-information display changes as shown on the next page each time you press the INFO (▲/▼) button or the SEL/ RESET button. When you turn the ignition switch to the ON (II) position, your last selection is displayed. U.
Multi-Information Display Trip Computer (See page 74.) HFL＊ (See page 77.) Tire Pressure for each tire (See page 76.) Outside Temperature (See page 74.) Engine Oil Life (See page 76.) : Press the INFO button (▲/▼). U.S. model is shown. ＊ : This display will be shown when the Bluetooth HandsFreeLink is activated. 72 2010 TSX : Press the SEL/RESET button.
Multi-Information Display Odometer U.S. Trip Meter Canada TRIP METER A TRIP METER B When you reset Trip A, average fuel economy A is reset at the same time. When you reset Trip B, average fuel economy B is reset. ODOMETER The odometer shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S.
Multi-Information Display Outside Temperature U.S. CANADA OUTSIDE TEMPERATURE This shows the outside Fahrenheit temperature in U.S. models, and Celsius temperature in Canadian models. The temperature sensor is in the front bumper. The temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your vehicle speed is under 19 mph (30 km/h).
Multi-Information Display ELAPSED TIME AVERAGE SPEED This shows the accumulated traveling time since you last reset it. When you turn the ignition switch to the ON (II) position, ELAPSED TIME is reset. This shows the average speed you are traveling in miles per hour (mph) for U.S. models or kilometers per hour (km/h) for Canadian models. You can customize the Trip A and AVERAGE FUEL A reset condition on the multi-information display (see page 89 ).
Multi-Information Display Engine Oil Life ENGINE OIL LIFE This shows the remaining engine oil life. It shows 100% after the engine oil is replaced and the display is reset. The engine oil life is calculated based on engine operating conditions. For more information, see page 403 . Tire Pressure Monitor U.S. Canada When the tire pressure monitor is shown on the multi-information display, press the SEL/RESET button. The display changes as shown. You can see the pressure of each tire in this monitor.
Multi-Information Display Bluetooth HandsFreeLink Instruments and Controls To use the system, your cell phone and the HFL system must be linked. Not all cell phones are compatible with this system. Refer to page 304 for instructions on how to link your cell phone to HFL and how to receive or make phone calls, or visit the acura.com/handsfreelink website. In Canada, visit www.acura. ca, or call 1-888-9-ACURA-9.
Multi-Information Display System Messages SYSTEM MESSAGE INDICATOR The system message(s) triggers the appropriate indicator(s) on the instrument panel, including the system message indicator, to come on. The system message indicator does not go off until the problem(s) is corrected. You will also hear a beep when the system message comes on for the first time.
Multi-Information Display See page 11 U.S. Canada See page 471 See page 19 See page 19 See page 472 U.S. Canada See page 471 See page 427 See page 32 U.S. U.S.
Multi-Information Display See page 65 See page 388 See page 114 6-cylinder models only See page 389 See page 389 See page 404 U.S.
Multi-Information Display Customized Settings You can customize some vehicle control settings. To enter the customizing mode, press and hold either INFO button (▲/▼) for more than 3 seconds. To change the settings, the ignition switch must be in the ON (II) position, and the vehicle must be stopped with the transmission in Park (automatic) or with the parking brake set (manual).
Multi-Information Display Group Setup METER SETUP (P.86) Menu Item LANGUAGE SELECTION ADJUST OUTSIDE TEMP. DISPLAY Changes the outside temperature reading above or below its current reading. TRIP A RESET with REFUEL Causes trip meter A and the average fuel economy to reset when you refuel. Resets the elapsed time of your current trip. ELAPSED TIME RESET POSITION SETUP＊2 (P.92) LIGHTING SETUP (P.94) Description Changes the language used in the display.
Multi-Information Display Group Setup DOOR SETUP (P.99) Menu Item AUTO DOOR LOCK DOOR LOCK MODE SECURITY RELOCK TIMER AUTO DOOR UNLOCK DEFAULT ALL (P.108) Changes which doors unlock with the remote transmitter in a first push. The exterior lights flash each time you press the LOCK or UNLOCK button. A beeper will also sound when you press the LOCK button twice. Changes how long it takes (in seconds) for the doors to relock and the security system to set after you unlock but do not open the door.
Multi-Information Display Each time you press the INFO (▲/ ▼) button, the screen changes as shown on the next page. Press the INFO (▲/▼) button until you see the setup you want to customize, then press the SEL/RESET button to enter your selection. Customize Settings You can customize some of the vehicle control settings to your preference. Here are the settings you can customize: METER SETUP POSITION SETUP＊ LIGHTING SETUP DOOR SETUP If you do not make any changes, select ‘‘EXIT.
Multi-Information Display METER SETUP See page 86. Any of the normal displays Instruments and Controls POSITION SETUP＊ See page 92. LIGHTING SETUP See page 94. DOOR SETUP See page 99. : Press the SEL/ RESET button. : Press the INFO button (▲/▼). : Press and hold the INFO button (▲/▼).
Multi-Information Display Meter Setup Here are the four custom settings for the meter setup: LANGUAGE SELECTION ADJUST OUTSIDE TEMP. DISPLAY TRIP A RESET with REFUEL ELAPSED TIME RESET While ‘‘METER SETUP’’ is shown, press the SEL/RESET button to enter the customize mode. Each time you press the INFO (▲/ ▼) button, the screen changes as shown in the illustration. Press the INFO (▲/▼) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.
Multi-Information Display Language Selection You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO (▲/▼) button repeatedly. Press the SEL/RESET button to see the selections. Select the desired language by pressing the INFO (▲/▼) button, then enter your selection by pressing the SEL/RESET button. When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
Multi-Information Display Adjust Outside Temp. Display U.S. models If you sometimes find that the temperature reading is a few degrees above or below the actual temperature, you can adjust it by following these instructions: Canadian models Adjust the outside temperature value by pressing the INFO (▲/▼) button repeatedly. Press the SEL/RESET button to set the desired value. U.S.
Multi-Information Display Trip A Reset With Refuel You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO (▲/▼) button repeatedly. Press the SEL/RESET button to see the selections. Select ON or OFF by pressing the INFO (▲/▼) button, then enter your selection by pressing the SEL/ RESET button. When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
Multi-Information Display Elapsed Time Reset There are three elapsed time reset choices you can make: IGN OFF − The elapsed time is reset when you turn the ignition switch to the LOCK (0) position. TRIP A − The elapsed time is reset when Trip A is reset. TRIP B − The elapsed time is reset when Trip B is reset. You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO (▲/▼) button repeatedly. 90 2010 TSX Press the SEL/RESET button to see the selections.
Multi-Information Display If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘ELAPSED TIME RESET’’ and repeat the procedure again. Instruments and Controls When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
Multi-Information Display Position Setup All models except Canadian TSX with 4-cylinder engine You can customize the MEMORY POSITION LINK setting in position setup. While ‘‘POSITION SETUP’’ is shown, press the SEL/RESET button to enter the customize mode. Each time you press the INFO (▲/ ▼) button, the screen changes as shown in the illustration. Press the INFO (▲/▼) button until you see the custom setting then press the SEL/RESET button to enter your selection. : Press the SEL/RESET button.
Multi-Information Display Memory Position Link Press the SEL/RESET button to see the selections. Select ON or OFF by pressing the INFO (▲/▼) button, then enter your selection by pressing the SEL/ RESET button. You can choose this item to customize from ‘‘POSITION SETUP’’ by pressing the INFO (▲/ ▼) button repeatedly. When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
Multi-Information Display Lighting Setup Here are the three custom settings for the lighting setup: INTERIOR LIGHT DIMMING TIME HEADLIGHT AUTO OFF TIMER AUTO LIGHT SENSITIVITY ＊ While ‘‘LIGHTING SETUP’’ is shown, press the SEL/RESET button to enter the customize mode. Each time you press the INFO (▲/ ▼) button, the screen changes as shown in the illustration. Press the INFO (▲/▼) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.
Multi-Information Display Interior Light Dimming Time You can choose this item to customize from ‘‘LIGHTING SETUP’’ by pressing the INFO (▲/ ▼) button repeatedly. Press the SEL/RESET button to see the selections. Select the desired setting (15 SEC, 30 SEC, or 60 SEC) by pressing the INFO (▲/▼) button, then enter your selection by pressing the SEL/ RESET button. When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
Multi-Information Display Headlight Auto Off Timer The headlights, parking lights, side marker lights, taillights, and license plate lights go off after the selected time when you remove the key from the ignition switch and close the driver’s door. To change how long the lights stay on before they go off, follow these instructions: You can choose this item to customize from ‘‘LIGHTING SETUP’’ by pressing the INFO (▲/ ▼) button repeatedly. 96 2010 TSX Press the SEL/RESET button to see the selections.
Multi-Information Display Auto Light Sensitivity All models except Canadian TSX with 4-cylinder engine MIN − The headlights come on when it is dark. Instruments and Controls The headlights automatically come on when the headlight switch is in the AUTO position and the ambient light reaches a changeable level. You can select the auto light sensitivity from the following five levels: MAX − The headlights come on when it is bright.
Multi-Information Display Press the SEL/RESET button to see the selections. Select the desired setting (MAX, HIGH, MID, LOW or MIN) by pressing the INFO (▲/▼) button, then enter your selection by pressing the SEL/RESET button. When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO LIGHT SENSITIVITY’’ and repeat the procedure again.
Multi-Information Display Door Setup Here are the five custom settings for the door setup: Instruments and Controls AUTO DOOR LOCK DOOR LOCK MODE KEYLESS LOCK ACKNOWLEDGMENT SECURITY RELOCK TIMER AUTO DOOR UNLOCK While ‘‘DOOR SETUP’’ is shown, press the SEL/RESET button to enter the customize mode. Each time you press the INFO (▲/ ▼) button, the screen changes as shown in the illustration.
Multi-Information Display Auto Door Lock There are three settings you can choose from: OFF − The auto door lock is deactivated all the time. WITH VEH SPD − The doors lock when the vehicle speed reaches about 10 mph (about 15 km/h). SHIFT FROM P − The doors lock whenever you move the shift lever out of Park. (Automatic transmission model only) A/T model is shown. You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO (▲/▼) button repeatedly.
Multi-Information Display If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO DOOR LOCK’’ and repeat the procedure again. To select whether the driver’s door unlocks or all the doors unlock when you unlock the doors with the remote transmitter or the key, follow these instructions. You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO (▲/▼) button repeatedly.
Multi-Information Display If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘DOOR LOCK MODE’’ and repeat the procedure again. Press the SEL/RESET button to enter the selecting mode. Select the desired setting by pressing the INFO (▲/▼) button, then enter your selection by pressing the SEL/RESET button. When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
Multi-Information Display Keyless Lock Acknowledgment To turn this feature on or off, follow these instructions. You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO (▲/▼) button repeatedly. Instruments and Controls When you push the LOCK button on the remote transmitter, some exterior lights flash, and a beeper sounds when you push the LOCK button again within 5 seconds to verify that the doors and the trunk are locked and the security system has set (see page 292 ).
Multi-Information Display Security Relock Timer If you unlock the doors with the remote transmitter, but do not open any of the doors within 30 seconds, the doors and the fuel fill door, automatically relock, and the security system sets. You can change this relock time from 30 seconds to 60 or 90 seconds. When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
Multi-Information Display If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘SECURITY RELOCK TIMER’’ and repeat the procedure again. Select the desired setting by pressing the INFO (▲/▼) button, then enter your selection by pressing the SEL/RESET button. Instruments and Controls Press the SEL/RESET button to enter the selecting mode. When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
Multi-Information Display Auto Door Unlock There are five possible settings for automatic transmission models and three possible settings for manual transmission models. Automatic transmission model only DRIVER DOOR with SHIFT to P − The driver’s door unlocks when you move the shift lever to Park. Automatic transmission model only DRIVER DOOR with IGN OFF − The driver’s door unlocks when you turn the ignition switch to the LOCK (0) position.
Multi-Information Display Press the SEL/RESET button to enter the selecting mode. Select the desired setting by pressing the INFO (▲/▼) button, then enter your selection by pressing the SEL/RESET button. If you choose ‘‘DRIVER DOOR with IGN OFF,’’ you will see the above display. Press the INFO (▲/▼) button to switch the door lock mode setting. Then, press the SEL/RESET button to enter your selection. If you choose ‘‘DRIVER DOOR with SHIFT to P,’’ you will see the above display.
Multi-Information Display DEFAULT ALL If you want to set the default settings, press the INFO (▲/▼) button to select DEFAULT ALL, then press the SEL/RESET button. To set the default settings, press the INFO (▲/▼) button to select SET then press the SEL/RESET button. If you want to cancel DEFAULT ALL, select CANCEL, then press the SEL/RESET button. The screen goes back to the previous display.
Controls Near the Steering Wheel HEADLIGHTS/TURN SIGNALS (P.111)/ FOG LIGHTS＊3 (P.115) INSTRUMENT PANEL BRIGHTNESS(P.115) WINDSHIELD WIPERS/ WASHERS (P.110) PASSENGER AIRBAG OFF INDICATOR (P.33) CENTER DISPLAY＊2 INTERFACE DIAL＊2 (P.222) SELECTOR KNOB＊3 (P.175) VEHICLE STABILITY ASSIST (VSA) SYSTEM OFF SWITCH (P.393) HAZARD WARNING BUTTON (P.117) REAR WINDOW DEFOGGER/ HEATED MIRROR BUTTON (P.117, 146) BLUETOOTH HANDSFREELINK SYSTEM VOICE CONTROL BUTTONS (P.
Windshield Wipers and Washers Push the right lever up or down to select a position. LO − The wipers run at low speed. HI − The wipers run at high speed. MIST − The wipers run at high speed until you release the lever. OFF − The wipers are not activated. ADJUSTMENT RING 1. MIST 2. OFF 3. INT − Intermittent 4. LO − Low speed 5. HI − High speed 6. Windshield washers INT − The length of the wipe interval is varied automatically according to vehicle’s speed. Vary the delay by turning the adjustment ring.
Turn Signals and Headlights Headlights − Turning the switch to the ‘‘ ’’ position turns on the parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights. 1. Turn signal 2. Off 3. Parking and instrument panel lights 4. AUTO＊ 5. Headlights on 6. High beams 7. Flash high beams 8. Fog lights off ＊ 9. Fog lights on＊ ＊ : If equipped Turning the switch to the ‘‘ ’’ position turns on the headlights.
Headlights All models except Canadian TSX with 4-cylinder engine AUTO − The automatic lighting feature turns on the headlights and all other exterior lights, when it senses low ambient light. To turn on automatic lighting, turn the light switch to AUTO. The lights will come on automatically when the outside light level becomes low (at dusk, for example). The lights on indicator comes on as a reminder. The lights and indicator will turn off automatically when the system senses high ambient light.
Headlights You can change this 15 second timer to 0, 30, or 60 seconds (see page 96 ). The automatic lighting off feature activates if you leave the headlight switch in the ‘‘ ’’ or ‘‘ ’’ position or if the lights are turned on by setting the switch in the ‘‘AUTO’’ position (if equipped), and you remove the key, then open and close the driver’s door. The lights will turn on again when you unlock or open the driver’s door.
Headlights Daytime Running Lights With the headlight switch off or in the position, the high beam headlights and the high beam indicator come on with reduced brightness when you turn the ignition switch to the ON (II) position and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake. The headlights revert to normal operation when you turn them on with the switch.
Fog Lights, Instrument Panel Brightness Fog Lights You can use the fog lights only when the headlights are on low beam. Instrument Panel Brightness INSTRUMENT PANEL BRIGHTNESS CONTROL KNOB The knob on the instrument panel controls the brightness of the instrument panel lights. Turn the knob to adjust the brightness with the ignition switch in the ON (II) position and the parking lights on.
Instrument Panel Brightness To reduce glare at night, the instrument panel illumination dims when you turn the light switch to the or position. Turning the knob to the right until you hear a tone will cancel the reduced brightness. BRIGHTNESS LEVEL When you turn the knob, the multiinformation display changes to vertical bars that show you the current level. The instrument panel will illuminate with reduced brightness when you unlock and open the driver’s door.
Hazard Warning Button, Rear Window Defogger Hazard Warning Button Rear Window Defogger HAZARD WARNING BUTTON The defogger will shut itself off within about 10 to 30 minutes according to the outside temperature (over 32°F, 0°C). The defogger and antenna wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe sideto-side. Push the button under the audio controls to turn on the hazard warning lights (four-way flashers).
Steering Wheel Adjustments Make any steering wheel adjustments before you start driving. LEVER 3. Push the lever forward fully to lock the steering wheel in position. To adjust Make sure the lever is positioned securely at the bottom of the steering column as shown. Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash. Adjust the steering wheel only when the vehicle is stopped. 4.
Keys and Locks MASTER KEY VALET KEY KEY NUMBER WITH REMOTE (Light Gray) TRANSMITTER TAG You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Acura-approved key blanks. These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged. Do not drop the keys or set heavy objects on them.
Keys and Locks Retractable Master Key RELEASE BUTTON Push Always make sure the key is fully extended when you insert it to the ignition switch. If the key is not fully extended, the immobilizer system may not operate properly and prevent the engine from starting. The key may come in contact with your finger while being retracted or extended. Make sure your fingers do not touch the pivot of the key when retracting or extending the key. The master key can be retracted into the remote transmitter.
Immobilizer System The immobilizer system protects your vehicle from theft. If an improperly coded key (or other device) is used, the engine’s fuel system is disabled. Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle inoperable. If you lose your key and you cannot start the engine, contact your dealer. Always take the ignition key with you whenever you leave the vehicle alone.
Ignition Switch LOCK (0) − You can insert or remove the key only in this position. To turn the key, push it in slightly. If your vehicle has an automatic transmission, the shift lever must also be in Park. If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key. The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III).
Ignition Switch START (III) − Use this position only to start the engine. The switch returns to the ON (II) position when you let go of the key. Instruments and Controls You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or the ACCESSORY (I) position and open the driver’s door. Remove the key to turn off the beeper. Removing the key from the ignition switch while driving locks the steering. This can cause you to lose control of the vehicle.
Door Locks LOCK TAB Lock To Lock Unlock To Unlock All doors can be locked from the outside by using the key in the driver’s door. To unlock only the driver’s door, insert the key, turn it clockwise, and release it. The remaining doors unlock when you turn the key a second time within a few seconds. You can customize the door lock/ unlock settings (see page 99 ).
Door Locks Default setting When the vehicle speed reaches about 10 mph (15 km/h) or more, all the doors lock automatically. When you shift to P after driving, the driver’s door unlocks. Lockout Prevention If you forget and leave the key in the ignition switch, lockout prevention will not allow you to lock the driver’s door. With any door open and the key in the ignition switch, locking with master door lock switch is disabled.
Remote Transmitter LED LOCK BUTTON TRUNK BUTTON UNLOCK BUTTON PANIC BUTTON LOCK − Press this button once to lock all doors. Some exterior lights will flash. When you push LOCK twice within 5 seconds, you will hear a beep to verify that the doors are locked and the security system has set. You cannot lock the doors if any door is not fully closed or if the key is in the ignition switch. UNLOCK − Press this button once to unlock the driver’s door (or all the doors depending on the door lock setting).
Remote Transmitter Recalling a Memorized Driving Position With Driver 1 With Driver 2 memory that is activated by the transmitter you normally carry. Here are the settings activated with the remote: Customized settings (see page 81 ). All models except Canadian TSX with 4-cylinder engine TRUNK − Press and hold this button for about 1 second to open the trunk. You cannot open the trunk if the key is in the ignition switch. Driving position memory (see page 142 ).
Remote Transmitter You will also see the ‘‘DRIVER 1’’ or ‘‘DRIVER 2’’ message on the multiinformation display, depending on which linked remote transmitter is used. You can turn off this driving position memory activation. Press and hold the LOCK and UNLOCK buttons at the same time. The LED in the remote transmitter will blink twice. Then release the buttons. Doing this also cancels the memory position link setting for that remote and restores the default settings.
Remote Transmitter 4. Remove the old battery and note the polarity. Make sure the polarity of the new battery is the same (＋ side facing down), then insert it in the keypad. An improperly disposed of battery can hurt the environment. Always confirm local regulations for battery disposal. 3. Place a cloth on the edge of the keypad to prevent scratches, and remove the upper half by carefully prying on the edge with a small flat-tip screwdriver. 5.
Trunk The trunk will lock when you lock the driver’s door with the key, the remote transmitter, either master door lock switch, or the lock tab on the driver’s door. TRUNK RELEASE SWITCH To unlock the trunk, turn the key twice to unlock the doors, push the rear of either master door lock switch, or push UNLOCK twice on the remote transmitter. TRUNK RELEASE BUTTON To open the trunk from the outside, push the release switch, then lift up.
Trunk Even if the trunk release is locked with the main switch, you can open the trunk with the remote transmitter. Trunk Main Switch MAIN SWITCH ON OFF To close the trunk, use the inner handle to lower the lid, then press down on the back edge. Keep the trunk lid closed at all times while driving to avoid damaging it, and to prevent exhaust gas from getting into the interior. See Carbon Monoxide Hazard, page 55 .
Trunk Emergency Trunk Opener TRUNK RELEASE LEVER Parents should decide if their children should be shown how to use this feature. Unlocking and Opening the Trunk Manually For more information about child safety, see page 39 . RELEASE BUTTON As a safety feature, your vehicle has a release lever on the trunk latch so the trunk can be opened from the inside. If the power door lock system cannot unlock the trunk, unlock and open it manually from inside the vehicle.
Trunk If you need to unlock and open the trunk manually, it means there may be a problem with the power door lock system or the trunk lock. Have the vehicle checked by your dealer. COVER Instruments and Controls 2. Pull up the cover of the tether anchor point on the left side. 3. Insert the master key in the lock on the rear shelf. 4. Turn the key clockwise, then release the key. The trunk lid will be opened. 5. Reinstall the head restraint.
Seats Power Seat Adjustments Driver’s seat only: See pages 13 − 14 for important safety information and warnings about how to properly position the seats and seatbacks. Moves the whole seat up and forward, or down and backward. The front of the seat also tilts up or down at the same time. The controls for the power adjustable front seats are on the outside edge of each seat bottom. You can adjust the seats with the ignition switch in any position. Make all seat adjustments before you start driving.
Seats Driver’s Lumbar Support Head Restraints See page 14 for important safety information and a warning about improperly positioning head restraints. They are most effective when you adjust them so the center of the back of the occupant’s head rests against the center of the restraint. Vary the lumbar support by moving the lever on the side of the seat-back. Move the lever forward or backward to adjust the lumbar support through its full range.
Seats Front Rear Center CUSHION CUSHION Failure to reinstall the head restraints can result in severe injury during a crash. Always replace the head restraints before driving. LEGS SEAT-BACK RELEASE BUTTON RELEASE BUTTON LEGS SEAT-BACK Adjusting the Head Restraint Removing the Head Restraint The head restraints adjust for height. You need both hands to adjust a restraint. Do not attempt to adjust it while driving. To raise it, pull upward.
Seats Active Head Restraints against whiplash and injuries to the neck and upper spine. For a head restraint system to work properly: Do not hang any items on the head restraints, or from the restraint legs. If the restraints do not return to their normal position, or in the event of a severe collision, have the vehicle inspected by an Acura dealer. Do not place any object between an occupant and the seat-back. Install each restraint in its proper location.
Seats Folding the Rear Seats The back of the rear seat folds down to give you direct access to the trunk. Each side folds down separately. With only half the seat folded, you can still carry a passenger in the back seat. The seat-back can be released from inside the trunk. GUIDE CENTER SHOULDER BELT When storing cargo, you can move the rear center shoulder belt out of the way by removing the belt from the guide.
Seats Make sure that the folded seat-back does not press against the front passenger’s seat, as this could cause the weight sensors to work improperly. Remove any items from the seat before you fold down the seat-back. Make sure the rear seat armrest is stored. To lock the seat-back upright, push it firmly against the trunk panel. Make sure it is latched in place by pulling on the top of the seat. Do not put any heavy items on the seat-back when it is folded down.
Seats Armrest Front Rear LEVER To use the console lid as an armrest, slide it to the desired position while pulling up the release lever. Release the lever to lock it in position where you want it to stop. The rear seat armrest is in the center of the rear seat. Pivot it down to use it. A beverage holder is located in the armrest.
Seat Heaters In the HI setting, the heater turns off when the seat gets warm, and turns back on after the seat’s temperature drops. Passenger’s Seat HEATERS Driver’s Seat Both front seats are equipped with seat heaters. Because of the sensors for the side airbag cutoff system, there is no heater in the passenger’s seat-back. The ignition switch must be in the ON (II) position to use the heaters.
Driving Position Memory System All models except Canadian TSX with 4-cylinder engine Your vehicle has a memory feature for the driver’s seat position. Two seat positions can be stored in separate memories. You select a memorized position by pushing the appropriate button or using the appropriate remote transmitter (Driver 1 or Driver 2). This setting can be linked or unlinked with the remote transmitter. To switch the link setting, see page 93 .
Driving Position Memory System To cancel the storing procedure after pressing the SET button, do any of the following: Selecting a Memorized Position MEMORY BUTTONS Readjust the seat position. On vehicles with manual transmission Turn the ignition switch out from the ON (II) position. Each memory button stores only one driving position. Storing a new position erases the previous setting stored in that button’s memory.
Driving Position Memory System To stop the system’s automatic adjustment, do any of these actions: Press any button on the control panel: SET, 1, or 2. Push any of the adjustment switches for the seat. If desired, you can use the adjustment switches to change the seat position after it is in its memorized position. If you change the memorized position, the indicator in the memory button will go out. To keep this seat position for later use, you must store it in the driver’s seat position memory.
Mirrors AUTO BUTTON SENSOR Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving. Adjusting the Power Mirrors ADJUSTMENT SWITCH There is also a sensor on the back of the mirror. Items hung on the mirror may block this sensor and af f ect its perf ormance. SELECTOR SWITCH 1. Turn the ignition switch to the ON (II) position. 2. Move the selector switch to L (driver’s side) or R (passenger’s side).
Mirrors 3. Push the appropriate edge of the adjustment switch to move the mirror right, left, up, or down. 4. When you finish, move the selector switch to the center (off) position. This turns the adjustment switch off to keep your settings. Reverse Tilt Door Mirror The passenger’s outside mirror has a reverse tilt feature. When in reverse, the mirror will tilt down slightly to improve your view as you parallel park. Shifting out of reverse will return the mirror to its original position.
Power Windows MAIN SWITCH INDICATOR Closing a power window on someone’s hands or fingers can cause serious injury. DRIVER’S WINDOW SWITCH To close either front window fully, pull back the window switch firmly to the second detent, then release it. The window automatically goes all the way up. To stop the window from going all the way up, push down on the window switch briefly. FRONT PASSENGER’S WINDOW SWITCH Turn the ignition switch to the ON (II) position to raise or lower any window.
Power Windows When you push the main switch in, the indicator comes on and the passengers’ windows cannot be raised or lowered. Use the main switch when you have children in the vehicle so they do not injure themselves by operating the windows unintentionally. To cancel this feature, push on the switch again. The switch will pop out and the indicator will go off. The windows and the main switch feature will operate for up to 10 minutes after you turn off the ignition switch.
Power Windows Opening the Windows and Moonroof with the Remote Transmitter You can open all of the windows and the moonroof from outside with the remote transmitter. 3. To open the windows and moonroof further, press the button again (within 10 seconds of step 1) and hold it. If the windows and the moonroof stop before the desired position, repeat steps 1 and 2. You cannot close the windows or the moonroof with the remote transmitter.
Power Windows 3. Turn the key clockwise again, and hold it. All four windows and the moonroof start to open. To stop the windows and the moonroof, release the key. 4. To open the windows and the moonroof further, turn and hold the key again (within 10 seconds of step 2). To close: 1. Insert the key in the driver’s door lock. 2. Turn the key counterclockwise, then release it. 3. Turn the key counterclockwise again, and hold it. All four windows and the moonroof start to close.
Moonroof MOONROOF SWITCH Open The moonroof can be tilted up in the back for ventilation, or it can be slid back into the roof. Use the switch on the front ceiling to operate the moonroof. You must turn the ignition switch to the ON (II) position to operate the moonroof. To open the moonroof, pull back on the switch and hold it. Release the switch when the moonroof reaches the desired position. To close the moonroof, push the switch forward and hold it. Release the switch to stop the operation.
Moonroof Auto Reverse If the moonroof runs into any obstacle while it is closing automatically, it will reverse direction, and then stop. To close the moonroof, remove the obstacle, then use the moonroof switch again. You can open and close the moonroof for up to 10 minutes after you turn off the ignition switch. Opening either front door cancels this function. Auto reverse stops sensing when the moonroof is almost closed.
Parking Brake PARKING BRAKE LEVER If you drive without releasing the parking brake, a beeper will sound, and you will also see a ‘‘RELEASE PARKING BRAKE’’ message on the multi-information display. Instruments and Controls Driving the vehicle with the parking brake applied can damage the rear brakes and hubs. A beeper will sound if the vehicle is driven with the parking brake on. To apply the parking brake, pull the lever up fully. To release it, pull up slightly, push the button, and lower the lever.
Interior Convenience Items COAT HOOK BEVERAGE HOLDER in REAR DOOR DRIVER’S POCKET SUN VISOR SUNGLASSES HOLDER VANITY MIRROR FRONT DOOR POCKET CENTER POCKET GLOVE BOX CARGO HOOKS CENTER POCKET＊ ACCESSORY POWER SOCKET SIDE POCKET BEVERAGE HOLDER in REAR SEAT ARMREST CONSOLE COMPARTMENT USB ADAPTER CABLE＊ ACCESSORY POWER SOCKET ＊: If equipped 154 2010 TSX BEVERAGE HOLDER AUXILIARY INPUT JACK
Interior Convenience Items Beverage Holders FRONT REAR Spilled liquids can damage the upholstery, carpeting, and electrical components in the interior. BEVERAGE HOLDER To use the front beverage holder, push on the lid. It will swing open. To close the lid, push it down until it latches. The rear seat also has a beverage holder in the center armrest. To use it, pivot the armrest down. 155 2010 TSX Instruments and Controls Push Be careful when you are using the beverage holders.
Interior Convenience Items Accessory Power Sockets FRONT Each socket is intended to supply power for 12 volt DC accessories that are rated 120 watts or less (10 amps). Console Compartment CONSOLE COMPARTMENT LEVER CONSOLE COMPARTMENT Your vehicle has two accessory power sockets; one is at the front of the center console and the other is in the console compartment. To use an accessory power socket, the ignition switch must be in the ACCESSORY (I) or ON (II) position.
Interior Convenience Items Glove Box Instruments and Controls To lock An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt. Always keep the glove box closed while driving. GLOVE BOX DETACHABLE SHELF Open the glove box by pulling the handle to the left. Close it with a firm push. Lock or unlock the glove box with the master key. Inside the glove box, there is a detachable shelf.
Interior Convenience Items Sunglasses Holder Push SHELF You can remove the shelf to get more space in the glove box. To remove it, open the glove box and pull out the shelf while disengaging its tabs from the glove box frame. To open the sunglasses holder, push then release the indent. It will unlatch and swing down. To close it, push it until it latches. Make sure the holder is closed while you are driving. 158 2010 TSX Some larger styles of sunglasses may not fit in the holder.
Interior Convenience Items Sun Visors Vanity Mirror Driver’s Pocket To use the sun visor, pull it down. You can also use the sun visor at the side window. Remove the support rod from the clip and swing the sun visor toward the side window. To use the vanity mirror on the back of the sun visor, pull up the cover. To open the driver’s pocket, push the button on the lid. To close it, push the lid up until it latches. The vanity mirror lights come on when you pull up the cover.
Interior Convenience Items Center Pockets Coat Hook COAT HOOK Push To open the pocket, push on the lid. To close it, push the lid down until it latches. On vehicles without navigation system To open the center pocket, push on the lid. It will unlatch and swing up. To close it, push the lid down until it latches. 160 2010 TSX To use a coat hook, slide it out slightly, then pull it down. Make sure the coat hook is pulled up when you are not using it. This hook is not designed for large or heavy items.
Interior Lights Ceiling Light DOOR ACTIVATED POSITION After all doors are closed tightly, the light dims slightly, then fades out in about 30 seconds. Spotlights To change the ‘‘INTERIOR LIGHT DIMMING TIME’’ setting, see page 95 . The ceiling light has a three-position switch: ON, Door Activated, and OFF. In the Door Activated (center) position, the light comes on when you: If you leave any door open without the key in the ignition switch, the ceiling light will go off after about 15 minutes.
Interior Lights OFF POSITION The spotlights (with the switch in the DOOR position) also come on when you unlock the door with the key or the remote transmitter, and when you remove the key from the ignition switch. Courtesy Lights DOOR ACTIVATED The spotlights have a two-position switch. In the DOOR position, the lights come on when you open any door. The lights fade out in about 30 seconds after the doors are closed tightly. In the OFF position, the lights do not come on.
Interior Lights COURTESY LIGHT Instruments and Controls The courtesy light between the spotlights comes on when you turn the parking lights on. To adjust its brightness, turn the instrument panel brightness control knob on the dashboard, with the ignition switch in the ON (II) position (see page 115 ). In addition to the courtesy light on the ceiling, the driver’s ambient foot light comes on.
164 2010 TSX
Features The climate control system in your vehicle provides a comfortable driving environment in all weather conditions. Your vehicle has an anti-theft audio system that requires a code number to enable it. The security system helps to discourage vandalism and theft of your vehicle. Models without navigation system Audio System ................................. 175 Playing the FM/AM Radio ........... 176 Playing the XM Radio ................. 183 Playing a Disc .................................
Climate Control System Without navigation system DRIVER’S SIDE TEMPERATURE With navigation system PASSENGER’S SIDE TEMPERATURE DRIVER’S SIDE TEMPERATURE AUTO INDICATOR CENTER DISPLAY DUAL BUTTON AUTO BUTTON DRIVER’S SIDE TEMPERATURE CONTROL SWITCH OFF BUTTON WINDSHIELD DEFOGGER BUTTON AIR CONDITIONING BUTTON PASSENGER’S SIDE TEMPERATURE CONTROL SWITCH MODE CONTROL BUTTON REAR WINDOW DEFOGGER/ HEATED MIRROR BUTTON RECIRCULATION BUTTON U.S. models are shown.
Climate Control System Voice Control System On models with navigation system The climate control system can also be operated by voice control. See the Navigation System manual for complete details. Using Automatic Climate Control The automatic climate control system in your vehicle maintains the interior temperature you select. The system also adjusts the fan speed and airflow levels. 2. Set the desired temperature with the temperature control switch.
Climate Control System When you set the temperature to its lower limit ( ) or its upper limit ( ), the system runs at full cooling or heating only. It does not regulate the interior temperature. system (GPS). If one side of the vehicle is getting too much sun, the system lowers the temperature only on that side. When you adjust a fan control, the fan is taken out of AUTO mode.
Climate Control System Fan Control Press the ▲ side of the bar to increase the fan speed and airflow. Press the ▼ side of the bar to decrease them. Air Conditioning (A/C) Button Recirculation Button This button turns the air conditioning on and off. You will see A/C ON or A/C OFF in the display. When the indicator in the button is on, air from the vehicle’s interior is sent through the system again. When the indicator is off, air is brought in from the outside of the vehicle (fresh air mode).
Climate Control System Rear Window Defogger Button This button turns the rear window defogger off and on (see page 117 ). Pushing this button also turns the power mirror heaters on and off. Mode Control Use the mode control button to select the vents the air flows from. Some air will flow from the dashboard vents in all modes. Airflow is divided between the floor and corner vents and the defroster vents at the base of the windshield.
Climate Control System Dual Temperature Control Your vehicle has two temperature control switches, one for the driver, and one for the front passenger. DUAL BUTTON Features The driver’s side and the passenger’s side temperature can be controlled independently by adjusting these switches when the green indicator in the DUAL button is on. Temperature Control Push AUTO or . The selected temperatures appear in the display (in the center display on models with navigation system).
Climate Control System To set the driver’s side temperature to a different value than the passenger’s, press the DUAL button, then push the switch up or down on the driver’s side. To set the passenger’s side to a different value than the driver’s, push the switch up or down on the passenger’s side. You can adjust the passenger’s side without pressing the DUAL button first. Driver’s Side When you set the temperature to its upper or lower limit, it is displayed as or .
Climate Control System Climate Control Sensors SUNLIGHT SENSOR Features TEMPERATURE SENSOR The climate control system has two sensors: a sunlight sensor on top of the dashboard, and a temperature sensor next to the steering column. Do not cover the sensors or spill any liquid on them.
Audio System An audio system is standard on all models. Read the appropriate pages (as shown below) to use your vehicle’s audio system. Audio system without navigation system Canadian TSX with 4-cylinder engine For vehicles without navigation system, see pages 175 through 221 . For vehicles with navigation system, see pages 222 through 283 .
Audio System (Models without navigation system) The knob turns left and right. Use it to scroll through lists, or to make selections or adjustments to a list or menu item on the display. When you make a selection, push the center of the selector (ENTER) to go to that selection. Selector Knob RETURN BUTTON SELECTOR KNOB Most audio system functions can be controlled by standard buttons, bars, and knobs. In addition, you can access some functions by using the selector knob on the audio system.
Playing the FM/AM Radio (Models without navigation system) Without XM Radio With XM Radio VOL/ (VOLUME/POWER) KNOB VOL/ (VOLUME/POWER) KNOB AM BUTTON AM BUTTON TITLE BUTTON TITLE BUTTON PRESET BUTTONS FM BUTTONS FOLDER BAR SCAN BUTTON SKIP BAR SELECTOR KNOB RETURN BUTTON FM BUTTON PRESET BUTTONS SKIP BAR CATEGORY BAR A.SEL (AUTO SELECT) BUTTON SCAN BUTTON SELECTOR KNOB RETURN BUTTON MENU BUTTON 176 2010 TSX A.
Playing the FM/AM Radio (Models without navigation system) The band and frequency that the radio was last tuned to are displayed. To change bands, press the AM or FM button. On the FM band, ST will be displayed if the station is broadcasting in stereo. Stereo reproduction in AM is not available. On the AM band, AM noise reduction turns on automatically. To Select a Station You can use any of five methods to find radio stations on the selected band: tune, skip, scan, the preset buttons, and auto select.
Playing the FM/AM Radio (Models without navigation system) Preset − Each preset button can store one frequency on AM and two frequencies on FM. 1. Select the desired band, AM or FM. FM1 and FM2 let you store six stations each. 2. Use the tune, skip, scan, or RDS function to tune the radio to a desired station. 3. Pick a preset button, and hold it until you hear a beep. 4. Repeat steps 1 through 3 to store a total of six stations on AM and twelve stations on FM.
Playing the FM/AM Radio (Models without navigation system) If the station you are listening to is not an RDS station, the display continues to show the frequency with the PS name display function on. Radio Data System (RDS) On the FM band, you can select a favorite station and display the program service name provided by the radio data system (RDS). The program service name display function shows the name of the station you are listening to. You can turn this function on or off.
Playing the FM/AM Radio (Models without navigation system) Radio Data System (RDS) Category RDS CATEGORY On the FM band selected, you can select the program category provided by the RDS. Press either side (▲ or ▼) of the CATEGORY bar (FOLDER bar on models without XM radio) to display and select an RDS category.
Playing the FM/AM Radio (Models without navigation system) RDS Program SCAN You can use the RDS program search or scan function even if the PS name display function is off. In this case, the display shows a frequency in place of a PS name. Adjusting the Sound Selector knob adjustable direction is shown. Features The scan function samples all stations with strong signals on the selected RDS category. To activate it, press and release the SCAN button. You will see SCAN in the display.
Playing the FM/AM Radio (Models without navigation system) SUBW − Adjusts the strength of sound from the subwoofer speaker. SVC − Adjusts the volume level based on the vehicle speed. CLOCK ADJUST − Adjusts the clock setting (see page 290 ). SUBWOOFER is selectable. Each mode is shown in the display as it changes. Turn the selector knob to adjust the setting to your liking. When the level reaches the center, you will see ‘‘C’’ in the display. BASS − Adjusts the bass. TREBLE − Adjusts the treble.
Playing the XM Radio (Models without navigation system) All models except Canadian TSX with 4-cylinder engine Features XM RADIO BUTTON TITLE BUTTON VOL/ (VOLUME/POWER) KNOB SKIP BAR CATEGORY BAR SCAN BUTTON U.S. model is shown.
Playing the XM Radio (Models without navigation system) All models except Canadian TSX with 4-cylinder engine Your vehicle is capable of receiving XM Radio anywhere in the United States and Canada, except Hawaii, Alaska, and Puerto Rico. XM is a registered trademark of Sirius XM Radio, Inc. and XM CANADA is a registered business name of Canadian Satellite Radio Inc. XM Radio receives signals from two satellites to produce clear, highquality digital reception. It offers many channels in several categories.
Playing the XM Radio (Models without navigation system) CATEGORY (▼ or ▲) − Press either side of the CATEGORY bar to select another category. TUNE − Turn the selector knob to change channel selections. Turn the knob right for higher numbered channels and left for lower numbered channels. In the category mode, you can only select channels within that category. You can also select a channel or category from the list by using the selector knob.
Playing the XM Radio (Models without navigation system) Preset − You can store up to 12 preset channels using the six preset buttons. Each button stores one channel from the XM1 band and one channel from the XM2 band. To store a channel: button. Either 1. Press the XM1 or XM2 will show in the display. 2. Use the selector knob, or the CATEGORY bar or SCAN button to tune to a desired channel. In category mode, only channels within that category can be selected. In channel mode, all channels can be selected.
Playing the XM Radio (Models without navigation system) The XM satellites are in orbit over the equator; therefore, objects south of the vehicle may cause satellite reception interruptions. To help compensate for this, ground-based repeaters are placed in major metropolitan areas. Signal weaker in these areas. Features Satellite signals are more likely to be blocked by tall buildings and mountains the farther north you travel from the equator.
Playing the XM Radio (Models without navigation system) There may be other geographic situations that could affect XM Radio reception. As required by the FCC: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Receiving XM Radio Service If your XM Radio service has expired or you purchased your vehicle from a previous owner, you can listen to a sampling of the broadcasts available on XM Radio.
Playing a Disc (Models without navigation system) Canadian TSX with 4-cylinder engine Without XM Radio All models except Canadian TSX with 4-cylinder engine With XM Radio VOL/ (VOLUME/POWER) KNOB VOL/ (VOLUME/POWER) KNOB MP3/WMA INDICATOR MP3/WMA INDICATOR CD BUTTON DISC SLOT DISC SLOT TITLE BUTTON DISC EJECT BUTTON TITLE BUTTON PRESET BUTTONS DISC EJECT BUTTON SKIP BAR SKIP BAR PRESET BUTTONS FOLDER BAR SCAN BUTTON SELECTOR KNOB RETURN BUTTON MENU BUTTON CATEGORY BAR SCAN BUTTON SELECTOR
Playing a Disc (Models without navigation system) To Play a Disc To load or play a disc, the ignition switch must be in the ACCESSORY (I) or ON (II) position. You operate the disc player with the same controls used for the radio. To select the disc player, press the CD button. You will see ‘‘CD’’ in the display. The disc and track numbers, and the elapsed time are shown in the display. You can also select the displayed information with the TITLE button (see page 191 ).
Playing a Disc (Models without navigation system) NOTE: If a file on a WMA disc is protected by digital rights management (DRM), the audio unit displays UNSUPPORTED, and then skips to the next file. Text Data Display Function Each time you press the TITLE button, the display shows you the text, if the disc was recorded with text data. You cannot load and play 3-inch (8-cm) discs in this unit. For information on how to handle and protect compact discs, see page 256 .
Playing a Disc (Models without navigation system) The display shows up to 16 characters of selected text data (the folder name, file name, etc.). If the text data has more than 16 characters, you will see the first 15 characters and the indicator on the display. Press and hold the TITLE button until the next 16 characters are shown. You can see up to 31 characters of text data. If you press and hold the TITLE button again, the display shows the first 15 characters again.
Playing a Disc (Models without navigation system) Folder Selection Press ENTER In MP3 or WMA mode, you can also select a folder or track/file from the list by using the selector knob. Push the selector knob (ENTER) to switch the display to the list displayed with three segments, then turn the knob to select a folder. Press the selector knob (ENTER) to change the display to the track/file list, then turn the same knob to select a track/file. Press the selector knob (ENTER) to set your selection.
Playing a Disc (Models without navigation system) To Select Repeat, Random or Scan Mode: Turn the selector knob to select an appropriate repeat, random or scan mode, then press the selector knob (ENTER) to set your selection. MENU ITEMS PLAY MODE ITEMS You can select any type of repeat, random and scan modes by using the MENU button and the selector knob. Push the MENU button to display the menu items, then turn the selector knob to select ‘‘PLAY MODE.
Playing a Disc (Models without navigation system) In MP3 or WMA mode REPEAT ONE FLD − This feature, when activated, replays all the files on the selected folder in the order they are compressed in MP3 or WMA. To activate folder repeat mode, select REPEAT ONE FLD from the menu items. You will see F-REPEAT in the display. The system continuously replays the current folder. Select normal play to turn it off.
Playing a Disc (Models without navigation system) SCAN TRK − The SCAN function samples all the tracks on the disc in the order they are recorded on the disc (all files in the selected folder in MP3 or WMA mode). To activate the scan feature, press and release the SCAN button. You will see SCAN in the display. You will get a 10 second sampling of each track/file in the disc/folder. Press and hold the SCAN button to get out of scan mode and play the last track sampled.
Playing a Disc (Models without navigation system) To Stop Playing a Disc Press the eject button ( ) to remove the disc. If you eject the disc, but do not remove it from the slot, the system will automatically reload the disc after 10 seconds and begin playing. If you turn the system off while a disc is playing, either with the VOL/ knob or by turning off the ignition switch, the disc will stay in the drive. When you turn the system back on, the disc will begin playing where it left off.
Disc Player Error Messages (Models without navigation system) The chart on the right explains the error messages you may see in the display while playing a disc. Error Message HEAT ERROR If you see an error message in the display while playing a disc, press the eject button. After ejecting the disc, check it for damage or deformation. If there is no damage, insert the disc again. For additional information on damaged discs, see page 257 . The audio system will try to play the disc.
Playing an iPod (Models without navigation system) All models except Canadian TSX with 4-cylinder engine USB INDICATOR iPod INDICATOR Features CD BUTTON TITLE BUTTON AUX BUTTON VOL/ (VOLUME/POWER) KNOB SKIP BAR RETURN BUTTON MENU BUTTON SELECTOR KNOB U.S. model is shown.
Playing an iPod (Models without navigation system) To Play an iPod This audio system can select and play the audio files on the iPod with the same controls used for the disc player. To play an iPod, connect it to the USB adapter cable in the console compartment by using your dock connector, then press the AUX button. The ignition switch must be in the ACCESSORY (I) or ON (II) position. The iPod will also be charged with the ignition switch in these positions.
Playing an iPod (Models without navigation system) NOTE: Do not connect your iPod using a hub. Connecting an iPod USB ADAPTER CABLE DOCK CONNECTOR Do not keep the iPod in the vehicle. Direct sunlight and high heat will damage it. Features Do not use an extension cable between the USB adapter cable equipped with your vehicle and your dock connector. We recommend backing up your data before playing it. USB CONNECTOR 1.
Playing an iPod (Models without navigation system) If the iPod indicator does not appear in the audio display, check the connections, and try to reconnect the iPod a few times. If the audio system still does not recognize the iPod, the iPod may need to be reset. Follow the instructions that came with your iPod, or you can find reset instructions online at www.apple.com/ ipod.
Playing an iPod (Models without navigation system) Pressing the RETURN button goes back to the previous display and pressing the MENU button cancels this setting mode. To Select a File from iPod Menu You can also select a file from any list on the iPod menu: playlists, artists, albums and songs, by using the selector knob. Push the selector knob (ENTER) to switch the display to an iPod menu, then turn the selector knob to select a desired list. Press ENTER to set your selection. Features Push ENTER.
Playing an iPod (Models without navigation system) To Select Repeat or Shuffle Mode: MENU ITEMS You can select any type of repeat and shuffle mode by using the MENU button and the selector knob. Press the MENU button to display the menu items, then turn the selector knob to select ‘‘PLAY MODE.’’ Press ENTER to set the selection.
Playing an iPod (Models without navigation system) REPEAT OFF − This feature turns off the repeat mode. SHUFFLE ALBUM − This feature plays all available albums in a selected list (playlists, artists, albums or songs) in random order. The files in each album are played in the recorded order. You will see ALB SHUF in the display. Select the normal play mode or SHUFFLE OFF to turn off this feature.
Playing an iPod (Models without navigation system) To Stop Playing Your iPod To play the radio, press the AM, FM, or (if equipped) button. Press the CD button to switch to the disc mode (if a disc is loaded). Press the AUX button to switch the audio mode between the Bluetooth Audio (if equipped) and iPod. Disconnecting an iPod You can disconnect the iPod at any time when you see ‘‘OK to disconnect’’ message＊ in the iPod display.
iPod Error Messages (Models without navigation system) If you see an error message on the audio display while playing an iPod, find the solution in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer. Error Message Solution FILE ERROR The system cannot read the file(s). Check the files in the iPod. There is a possibility that the files have been damaged. Appears when an unsupported iPod is inserted.
Playing a USB Flash Memory Device (Models without navigation system) All models except Canadian TSX with 4-cylinder engine FILE TYPE INDICATOR USB INDICATOR CD BUTTON TITLE BUTTON AUX BUTTON VOL/ (VOLUME/POWER) KNOB SKIP BAR CATEGORY BAR RETURN BUTTON MENU BUTTON SELECTOR KNOB U.S. model is shown.
Playing a USB Flash Memory Device (Models without navigation system) The audio system reads and plays the audio files on the USB flash memory device in MP3, WMA or AAC＊ formats. Depending on the format, the display shows MP3, WMA or AAC when a USB flash memory device is playing. The USB flash memory device limit is up to 700 folders or up to 65535 files. The recommended USB flash memory devices are 256 MB or higher. Some digital audio players may be compatible as well.
Playing a USB Flash Memory Device (Models without navigation system) The order of files in USB playback may be different from the order of files displayed in PC or other devices etc. Files are played in the order stored in USB flash memory device. −Bitrate: 48−320/VBR kbps (Max 384) −Supported standards: WMA version 7/8/9 −Partition: Top partition only −Maximum layers: 8 The specifications for compatible MP3 files are: −Sampling frequency: 32/44.1/48 kHz (MPEG1) 16/22.
Playing a USB Flash Memory Device (Models without navigation system) Connecting a USB Flash Memory Device Text Data Display Function Each time you press the TITLE button, the display mode shows you in sequence, the folder name, the file name, the artist name, the album name, the song name, or name off (which turns off the text display). USB ADAPTER CABLE 1. Unclip the USB connector by pivoting it, and pull out the USB adapter cable in the console compartment. 2.
Playing a USB Flash Memory Device (Models without navigation system) To Change or Select Files Use the SKIP bar while a USB flash memory device is playing to select passages and change files. SKIP − Each time you press and release the side of the SKIP bar, the system skips forward to the beginning of the next file. Press and release the side of the bar, to skip backward to the beginning of the current file. Press it again to skip to the beginning of the previous file.
Playing a USB Flash Memory Device (Models without navigation system) Pressing the RETURN button goes back to the previous display and pressing the MENU button cancels this setting mode. To Select Repeat, Random or Scan Mode: MENU ITEMS Turn the selector knob to select an appropriate repeat, random or scan mode, then press the selector knob (ENTER) to set your selection. Features You can select any type of repeat, random and scan modes by using the MENU button and the selector knob.
Playing a USB Flash Memory Device (Models without navigation system) PLAY MODE ITEMS REPEAT ONE FLD − This feature replays all the files on the selected folder in the order they are stored. Select normal play to turn it off. Pressing either side of the CATEGORY bar also turns off this feature. RANDOM IN FLD − This feature plays the files in the selected folder in random order. You will see F-RANDOM in the display. Select normal play to turn it off. REPEAT ONE TRK − This feature continuously plays a file.
Playing a USB Flash Memory Device (Models without navigation system) You can also select the folder scan feature from the menu items with the selector knob (see page 213 ). Select normal play to turn either scan feature off. Pressing either side of the CATEGORY or SKIP bar also turns off the feature. To Stop Playing a USB Flash Memory Device To play the radio, press the FM, AM or button. Press the CD button to switch to the disc mode (if a disc is loaded).
USB Flash Memory Device Error Messages (Models without navigation system) If you see an error message on the audio display while playing a USB flash memory device, find the solution in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer. Error Message FILE ERROR MEDIA ERROR Solution The system cannot read the file(s). Check the files in the USB flash memory device. There is a possibility that the files have been damaged.
Bluetooth Audio System (Models without navigation system) Features TITLE BUTTON AUX BUTTON SKIP BAR U.S. model is shown.
Bluetooth Audio System (Models without navigation system) Your vehicle is equipped with a Bluetooth Audio system, which allows you to listen to streaming audio from your Bluetooth Audio compatible phone. This function is only available on phones that are paired and linked to the vehicle’s Bluetooth HandsFreeLink (HFL) system (see page 311 ). Not all Bluetooth-enabled phones with streaming audio capabilities are compatible with the system. You can find an approved phone by visiting www.acura.
Bluetooth Audio System (Models without navigation system) In the following conditions, the display shows ‘‘NO CONNECT’’ message. Features The phone is not linked to HFL. The phone is not turned on. The phone is not in the vehicle. Another HFL compatible phone, which is not compatible for Bluetooth Audio, is already connected. To skip a file Press the side of the SKIP bar to skip forward to the next file, and press the side to skip backward to the beginning of the current file.
Bluetooth Audio System (Models without navigation system) To change sound settings To switch to HFL mode If you receive a call when the Bluetooth Audio is playing, press the HFL Talk button on the steering wheel. The display switches to the HFL mode (see page 307 ). After ending the call, press the HFL Back button to go back to the Bluetooth Audio mode. Press the MENU button to display the audio settings. Turn the selector to select a desired sound mode, then press ENTER to set your selection.
Bluetooth Audio System (Models without navigation system) Features As required by the FCC: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Audio System (Models with navigation system) Interface Dial Most audio system functions can still be controlled by standard buttons, dials, and knobs, but some functions can only be accessed using the interface dial. The interface dial has two parts, a knob and a selector. ENTER KNOB SELECTOR The knob turns left and right. Use it to make selections or adjustments to a list or menu on the screen. The selector can be pushed left, right, up, down, and in.
Playing the FM/AM Radio (Models with navigation system) NAVIGATION SCREEN Features VOL/ (VOLUME/POWER) KNOB CENTER DISPLAY FM/AM BUTTON PRESET BUTTONS (SOUND) BUTTON CATEGORY BAR TUNE BAR SKIP BAR SCAN/A.SEL (SCAN/ AUTO SELECT) BAR AUDIO BUTTON U.S. model is shown.
Playing the FM/AM Radio (Models with navigation system) To Play the FM/AM Radio STEREO ICON BAND the FM/AM button. You can also change bands by pushing the interface selector up. Each time you push it up, the band will change to FM1, FM2, or AM. On the FM bands, STEREO will be shown on the navigation screen and ST on the center display, if the station is broadcasting in stereo. Stereo reproduction on AM is not available. On the AM band, AM noise reduction turns on automatically.
Playing the FM/AM Radio (Models with navigation system) SCAN ICON Features SKIP (SEEK) − The skip (seek) function searches up and down from the current frequency to find a station with a strong signal. To activate it, press either side ( or ) of the SKIP bar, then release it. You can also activate the skip function (SEEK is displayed on the screen) by pushing the interface selector to the right or left. TUNE ICON TUNE − Use the TUNE bar to tune the radio to a desired frequency.
Playing the FM/AM Radio (Models with navigation system) When the system finds a strong signal, it will stop and play that station for about 10 seconds. If you do nothing, the system will then scan for the next strong station and play it for 10 seconds. When it plays a station that you want to listen to, press the scan side of the bar again, or push the interface selector to the right again. Preset − Each preset button or preset icon can store one frequency on AM and two frequencies on FM.
Playing the FM/AM Radio (Models with navigation system) To turn off auto select, press ENTER on the interface selector. Program Service (PS) Name Display The program service name display function shows the name of the station you are listening to. You can turn this function on or off. Features You can also press the A.SEL side of the SCAN/A.SEL bar. You will see A.SEL on the screen, and the system goes into scan mode for several seconds.
Playing the FM/AM Radio (Models with navigation system) If the station you are listening to is not an RDS station, the audio screen and the center display continue to show the frequency. Radio Data System (RDS) Category When you turn off this function by pressing the TITLE button, the center display shows ‘‘PS OFF.’’ RDS SEARCH ICON With the FM band selected, you can select the program type provided by the RDS. Press the AUDIO button to display the radio information on the screen.
Playing the FM/AM Radio (Models with navigation system) RDS Program Search Turn the selector to select an RDS category. You can use the search or scan function to find radio stations on the selected RDS category by pressing the selector to the right repeatedly. Press ENTER to set your selection. If you do nothing while the RDS category is selected, the selected category is canceled. RDS CATEGORY U.S. model is shown. You can also select an RDS category with the CATEGORY bar.
Playing the FM/AM Radio (Models with navigation system) SEEK/SCAN ICON Turn the knob to the desired RDS category. While the RDS category is selected, move the selector knob to the right to select SEEK in the upper right corner of the screen. Then press ENTER to activate the seek function. RDS CATEGORY LIST SEEK is selected. To activate RDS program search with the interface dial, push the AUDIO button to display the FM radio information on the screen.
Playing the FM/AM Radio (Models with navigation system) If you do nothing, the system will scan for the next strong station and play it for 10 seconds. When it plays a station that you want to listen to, press the SCAN side of the SCAN/ A.SEL bar again. Turn the knob to the desired RDS category. While the RDS category is selected, move the selector knob to the right to select SCAN in the upper right corner of the screen. Then press ENTER to activate the scan function. RDS CATEGORY LIST SCAN is selected.
Playing the FM/AM Radio (Models with navigation system) Radio Text Display This function displays the radio text information of the selected RDS station. TEXT INDICATOR If the selected RDS station has the radio text information, you will see the text indicator on the screen. The text is displayed according to the information from RDS. RADIO TEXT ICON To activate radio text display, use the interface dial. Push the selector down, and turn the knob to select RADIO TEXT icon.
Playing the FM/AM Radio (Models with navigation system) These adjustments can be made with the (Sound) button or the interface dial. Features Adjusting the Sound BASS, TREBLE, FADER, and BALANCE are each adjustable. You can also adjust the strength of the sound coming from the center and subwoofer speakers. In addition, you can set the Dolby PL (ProLogic) II and Speed-sensitive volume compensation (SVC).
Playing the FM/AM Radio (Models with navigation system) The system will return to the audio playing mode in the center display about 10 seconds after you stop adjusting a mode. BASS/TREBLE − To adjust bass and treble, select BASS or TREBLE, and press ENTER on the interface selector. The current setting is shown on the display. Turn the interface knob to the desired level, and enter your selection by pressing ENTER on the interface selector.
Playing the FM/AM Radio (Models with navigation system) NOTE: In some audio playing modes (XM, AUX), when DPLII is on, the music coming from the rear speakers may sound distorted. This is due to compression of the music, and it does not indicate a problem with the setting. Speed-sensitive Volume Compensation (SVC) The SVC mode controls the volume based on vehicle speed. The faster you go, the louder the audio volume becomes. As you slow down, the audio volume decreases.
Playing the XM Radio (Models with navigation system) TITLE BUTTON VOL/ (VOLUME/POWER) KNOB XM RADIO BUTTON CENTER DISPLAY PRESET BUTTONS CATEGORY BAR SKIP BAR TUNE BAR SCAN/A.SEL (SCAN/ AUTO SELECT) BAR AUDIO BUTTON U.S. model is shown.
Playing the XM Radio (Models with navigation system) XM Radio receives signals from two satellites to produce clear, highquality digital reception. It offers many channels in several categories. Along with a large selection of different types of music, XM Radio also allows you to view channel and category selections in the audio display. Operating the XM Radio Push the AUDIO button to display XM information on the screen. You can operate the XM Radio system with the interface dial.
Playing the XM Radio (Models with navigation system) MODE − To switch between the category mode and channel mode, press and hold the TITLE button until the mode changes. The CATEGORY or CHANNEL mode is displayed on the screen. To switch the mode with the interface dial, push down the interface selector to select AUDIO MENU, then turn the knob to select MODE, and press ENTER on the selector repeatedly. In the category mode, such as Jazz, Rock, Classical, etc.
Playing the XM Radio (Models with navigation system) CATEGORY (▼ or ▲) − Press either side of the bar to select another category. You can also change a category by pushing the interface selector left or right. The system plays each channel in numerical order for a few seconds, then selects the next channel. When you hear a channel you want to continue listening to, push the interface selector to the right again or press the SCAN side of the bar to cancel.
Playing the XM Radio (Models with navigation system) button or scroll 5. Press the up again. The other XM band will be shown. Store the next six channels using steps 2 and 3. Once a channel is stored, press and release the proper preset button to tune to it. XM Radio Display Messages ‘‘LOADING’’ − XM is loading the audio or program information. ‘‘OFF AIR’’ − The channel currently selected is no longer broadcasting. ‘‘UPDATING’’ − The encryption code is being updated.
Playing the XM Radio (Models with navigation system) Depending on where you drive, you may experience reception problems. Interference can be caused by any of these conditions: Driving on the north side of an east/west mountain road. Driving on the north side of a large commercial truck on an east/west road. Signal may be blocked by mountains or large obstacles to the south. Signal weaker in these areas.
Playing the XM Radio (Models with navigation system) Note Function If equipped NOTE ICON This function stores the sound content played on the selected satellite radio station with the channel, category, name and title information. To activate this function, press and hold the button for about 2 seconds while a song or passage which you want to store is playing. The function records for about 10 seconds, enough for you to identify the selection when you play it back.
Playing the XM Radio (Models with navigation system) To delete a file, select it by turning the selector knob, then push it to the right. Select ‘‘Delete All’’ or ‘‘Delete Selected Item,’’ then press ENTER. If you decide to purchase XM radio service, contact XM Radio at www.xmradio.com, or at 1-800-852-9696. In Canada, contact XM CANADA at www.xmradio.ca, or at 1-877-209-0079. You will need to give them your radio I.D. number and your credit card number. To get your radio I.D.
Playing Discs (Models with navigation system) NAVIGATION SCREEN VOL/ (VOLUME/POWER) KNOB TITLE BUTTON CENTER DISPLAY DISC BUTTON PRESET BUTTONS CATEGORY BAR SKIP BAR SCAN/A.SEL (SCAN/ AUTO SELECT) BAR AUDIO BUTTON INTERFACE DIAL DISC SLOT DISC EJECT BUTTON DISC LOAD BUTTON U.S. model is shown.
Playing Discs (Models with navigation system) Your vehicle’s audio system has an in-dash disc changer with the same controls used for the radio. To operate the disc changer, the ignition switch must be in the ACCESSORY (I) or the ON (II) position. The disc packages or jackets should have one of these marks. The changer can also play MP3 or WMA format (see page 251 ).
Playing Discs (Models with navigation system) DVD-A discs not meeting DVD verification standards may not be playable. Video CDs and DVD-V format discs will not work in this unit. Do not use discs with adhesive labels. The label can curl up and cause the disc to jam in the unit. Some CD-DA and CD-ROM mixed discs are not playable. Manufactured under license under U.S. Patent ＃’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending.
Playing Discs (Models with navigation system) 4. Repeat this until all six positions are loaded. If you are not loading all six positions, the system will then begin playing the last disc loaded. To load a single disc: 1. Press and release the LOAD button. 2. ‘‘NO DISC’’ is shown on the screen for an empty position in the changer. When the green load indicator comes on and you see ‘‘DISC LOAD’’ in the center display, insert the disc into the slot.
Playing Discs (Models with navigation system) The player can play CD-TEXT, MP3, and WMA formats. When you play CD-TEXT, you will see the track name, artist name, and album name on the screen. When you play MP3/WMA discs, you will see the track name and folder name on the screen. If the disc was not recorded with this information, it will not be displayed.
Playing Discs (Models with navigation system) To exit the track list display, press the AUDIO button, or push the interface selector to the left, or press the cancel button. If you don’t, the system advances to the next track, plays about 10 seconds of it, and continues through the rest of the tracks the same way. If you don’t, the system advances to the next disc, plays about 10 seconds of its first track, and continues through the rest of the discs the same way.
Playing Discs (Models with navigation system) AUDIO MENU SCREEN Turn the interface knob to select a desired repeat or random mode, then press ENTER to set your selection. To cancel the selected repeat or random mode, have the selected mode highlighted, then press ENTER on the interface selector. Track Repeat To replay the current track continuously, select TRACK REPEAT, and press ENTER on the interface selector. As a reminder, you will see REPEAT next to TRACK on the screen.
Playing Discs (Models with navigation system) To Stop Playing a Disc To take the system out of disc mode, press the FM/AM button, the button, or the AUX button. To return to disc mode, press the DISC button. Playing a DVD-A Disc Use the disc controls previously described. The specifications for compatible MP3 files are: −Sampling frequency: 32/44.1/48 kHz (MPEG1) 16/22.
Playing Discs (Models with navigation system) Changing the Folders While playing an MP3/WMA disc, you can select a folder within the disc by pressing either side of the category bar. Each time you press either side of the bar, the folder title and its first file’s information appear in the display in recorded order. Changing and Selecting the Folders/ Files MP3/WMA INDICATOR Using the interface selector, you can see the list of all the files and folders within a disc.
Playing Discs (Models with navigation system) CURRENT TRACK To listen to the rest of the folder, press and hold the SCAN side of the bar until you hear a beep. If you do nothing, the system advances to the next folder, plays 10 seconds of it, and continues with the remaining folders in the same way. When the system has finished sampling the first file in all folders, folder scan is canceled, and the last file played continues to play.
Playing Discs (Models with navigation system) Folder Random This feature, when activated, plays all files in the current folder in random order. To activate folder random play, select FOLDER RANDOM by interface knob, and press ENTER on the interface selector. You will see RANDOM next to FOLDER on the screen. To turn this feature off, highlight FOLDER RANDOM (if not already highlighted), and press ENTER on the interface selector again. To select any type of the random modes, use the interface dial.
Disc Changer Error Messages (Models with navigation system) The chart on the right explains the error messages you may see in the center display while playing a disc. Error Message HEAT ERROR The audio system will try to play the disc. If there is still a problem, the error message will reappear. Press the eject button, and pull out the disc. Insert a different disc. If the new disc plays, there is a problem with the first disc.
Protecting Your Discs General Information When using CD-R or CD-RW discs, use only high quality discs labeled for audio use. When recording a CD-R or CD-RW, the recording must be closed for it to be used by the disc changer. When using DVD-R/RW discs, they should meet DVD verification standards. Play only standard, round, 5-inch (12 cm) discs. Smaller or oddshaped discs may jam in the drive or cause other problems. Handle your discs properly to prevent damage and skipping.
Protecting Your Discs Examples of these discs are shown to the right: 1. Bubbled, wrinkled, labeled, and excessively thick discs Bubbled/ Wrinkled With Label/ Sticker 2. Damaged discs Chipped/ Cracked Using Printer Label Kit Sealed With Plastic Ring 3. Poor quality discs Warped Burrs CONTINUED 257 2010 TSX Features Additional Information on Recommended Discs The in-dash disc player/changer has a sophisticated and delicate mechanism.
Protecting Your Discs 4. Small, irregular shaped discs 3-inch (8-cm) CD 5. Discs with scratches, dirty discs Triangle Shape Fingerprints, scratches, etc. Recommended discs are printed with the following logo. Audio unit may not play the following formats. CD-R or CD-RW may not play due to the recording conditions. Scratches and fingerprints on the discs may cause the sound to skip. This audio unit cannot play a Dualdisc .
Playing an iPod (Models with navigation system) USB ICON iPod ICON Features CENTER DISPLAY AUX BUTTON SKIP BAR MAP BUTTON AUDIO BUTTON CANCEL BUTTON INTERFACE DIAL 259 2010 TSX
Playing an iPod (Models with navigation system) To Play an iPod This audio system can operate the audio files on the iPod with the same controls used for the in-dash disc changer. To play an iPod, connect it to the USB adapter cable in the console compartment by using your dock connector, then press the AUX button. The ignition switch must be in the ACCESSORY (I) or ON (II) position. The iPod will also be recharged with the ignition switch in these positions.
Playing an iPod (Models with navigation system) NOTE: Do not connect your iPod using a hub. Connecting an iPod USB ADAPTER CABLE Do not keep the iPod in the vehicle. Direct sunlight and high heat will damage it. USB ADAPTER CABLE Features Do not use an extension cable between the USB adapter cable equipped with your vehicle and your dock connector. We recommend backing up your data before playing it. USB CONNECTOR 1.
Playing an iPod (Models with navigation system) If the iPod indicator does not appear in the audio display, check the connections, and try to reconnect the iPod a few times. If the audio system still does not recognize the iPod, the iPod may need to be reset. Follow the instructions that came with your iPod, or you can find reset instructions online at www.apple.com/ The current file number and total of the selected playable files are displayed in the center display.
Playing an iPod (Models with navigation system) To Select a File from iPod Menu Features You can also change files with the interface dial. Press the AUDIO button to show the audio control display on the navigation screen. Push the selector to the right side to skip forward and to the left side to skip backward. You can also select a file from any of the iPod menus: playlists, artists, albums and songs, by using the interface dial.
Playing an iPod (Models with navigation system) If you select ‘‘ALL’’ on either the artists or albums list, all available files on the selected list are played. To Select Repeat or Random Mode: Press the AUDIO button to go back to the normal audio playing display. Pressing the CANCEL button goes back to the previous screen, and pressing the MAP button cancels the audio control display on the screen. Push down the selector. You can select any type of repeat and random mode on the audio menu.
Playing an iPod (Models with navigation system) TRACK RANDOM − This feature plays all available files from the selected items in the iPod menu list (playlists, artists, albums or songs) in random order. You will see TRACK RANDOM on the screen. REPEAT − This feature continuously plays a file. To turn it off, press ENTER again. Features To turn it off, have this mode highlighted and press ENTER again.
Playing an iPod (Models with navigation system) To turn it off, have this mode highlighted and press ENTER again. You can also select another list from the iPod menu while keeping the random function. NOTE: Available operating functions vary on models or versions. Some functions may not be available on the vehicle’s audio system. To Stop Playing Your iPod To play the radio, press the AM, FM, or button. Press the DISC button to switch to the disc mode (if a disc is loaded).
Playing an iPod (Models with navigation system) If you reconnect the same iPod, the system may begin playing where it left off, depending on what mode the iPod is in when it is reconnected. iPod Error Messages If you see an error message in the center display, see page 268 .
iPod Error Messages (Models with navigation system) If you see an error message in the center display while playing an iPod, find the solution in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer. Error Message FILE ERROR MEDIA ERROR Solution The system cannot read the file(s). Check the files in the iPod. There is a possibility that the files have been damaged. Appears when an unsupported iPod is inserted.
Playing a USB Flash Memory Device (Models with navigation system) AUDIO CONTROL DISPLAY Features VOL/ (VOLUME/POWER) KNOB (SOUND) BUTTON USB INDICATOR CENTER DISPLAY AUX BUTTON CATEGORY BAR SKIP BAR MAP BUTTON SCAN/A.
Playing a USB Flash Memory Device (Models with navigation system) To Play a USB Flash Memory Device This audio system can operate the audio files on a USB flash memory device with the same controls used for the in-dash disc changer. To play a USB flash memory device, connect it to the USB adapter cable in the console compartment, then press the AUX button. The ignition switch must be in the ACCESSORY (I) or ON (II) position.
Playing a USB Flash Memory Device (Models with navigation system) Voice Control System You can select the AUX mode by using the navigation system voice control buttons, but cannot operate the play mode functions. The specifications for compatible AAC files are: −Sampling frequency: 8/11.025/12/16/22.05/24/32/ 44.1/48 kHz −Bitrate: 48−320 kbps −Supported standards: MPEG4/AAC LC MPEG2/AAC LC −Partition: Top partition only −Maximum layers: 8 Some versions of MP3, WMA, or AAC format may not be supported.
Playing a USB Flash Memory Device (Models with navigation system) When the USB device is connected and the USB mode is selected on the audio system, the USB indicator is shown in the center display. It also shows the folder and file numbers. Pressing the AUDIO button displays the folder and file names, and the elapsed time in the navigation screen. Connecting a USB Flash Memory Device USB ADAPTER CABLE USB ADAPTER CABLE USB CONNECTOR 1.
Playing a USB Flash Memory Device (Models with navigation system) Folder Selection − To select a different folder, press and release either side of the CATEGORY bar. Press the ▲ side to skip to the next folder, and press the ▼ side to skip to the beginning of the previous folder. To Change or Select Files Use the SKIP bar while a USB flash memory device is playing to select passages and change files. To move rapidly within a file, press and hold either side ( or ) of the SKIP bar.
Playing a USB Flash Memory Device (Models with navigation system) To Select a File from Folder and File Lists You can also select a folder or file from the list by using the interface dial. Press the AUDIO button to show the audio control display on the navigation screen. Push up the selector on the interface dial to switch the display to the folder list, then turn the knob on the interface dial to select a folder.
Playing a USB Flash Memory Device (Models with navigation system) highlighted play mode, then press ENTER to turn off that selected mode. To Select Repeat, Random or Scan Mode: TRACK RANDOM − This feature plays all the files in random order. TRACK REPEAT − This feature continuously plays a file. Pressing either side of the SKIP bar also turns off this feature. You can select any type of repeat, random and scan modes on the audio menu screen.
Playing a USB Flash Memory Device (Models with navigation system) TRACK SCAN − This function samples all files in the selected folder in the order they are stored. To activate the scan feature, push the selector to the right. You will see TRACK SCAN on the screen. You will also see SCAN on the center display and the file number blinking. You will get a 10 second sampling of each file in the folder. Push the selector repeatedly to get out of the scan mode. The system plays the last file sampled.
Playing a USB Flash Memory Device (Models with navigation system) If you reconnect the same USB flash memory device, the system will begin playing where it left off. Disconnecting a USB Flash Memory Device You can disconnect the USB flash memory device at any time even if the USB mode is selected on the audio system. Make sure to follow the USB flash memory device’s instructions when you remove it. USB Flash Memory Device Error Messages If you see an error message in the center display, see page 278 .
USB Flash Memory Device Error Messages (Models with navigation system) If you see an error message in the center display while playing a USB flash memory device, find the solution in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer. Error Message FILE ERROR MEDIA ERROR Solution The system cannot read the file(s). Check the files in the USB flash memory device. There is a possibility that the files have been damaged.
Bluetooth Audio System (Models with navigation system) Features TITLE BUTTON AUX BUTTON SKIP BAR AUDIO BUTTON U.S. model is shown.
Bluetooth Audio System (Models with navigation system) Your vehicle is equipped with a Bluetooth Audio system, which allows you to listen to streaming audio from your Bluetooth Audio compatible phone. This function is only available on phones that are paired and linked to the vehicle’s Bluetooth HandsFreeLink (HFL) system (see page 311 ). Not all Bluetooth-enabled phones with streaming audio capabilities are compatible with the system. You can find an approved phone by visiting www.acura.
Bluetooth Audio System (Models with navigation system) In the following conditions, the display shows ‘‘NO CONNECT’’ message after pressing the TITLE button. To skip a file Press the side of the SKIP bar to skip forward to the next file, and press the side to skip backward to the beginning of the current file. Push the side again to skip to the previous file. You can also operate the skip function with the interface dial on the audio control display of the navigation screen. Push the AUDIO button.
Bluetooth Audio System (Models with navigation system) To pause or resume a file Turn the knob on the interface dial to switch the setting between the resume/pause mode and the sound mode. Select RESUME/PAUSE, then press ENTER to set your selection. Each time you press ENTER, the system switches between the resume mode and pause mode. To change sound settings NOTE: The pause function may not be available on some phone devices. The resume/pause mode can stop playing a file temporarily.
Bluetooth Audio System (Models with navigation system) Turn the knob to select a sound mode, then press ENTER to set your selection. Turn the knob to your liking (see page 233 for more sound setting information). To switch to HFL mode After ending the call, press the HFL Back button to go back to the Bluetooth Audio mode.
FM/AM Radio Reception FM/AM Radio Frequencies The radio can receive the complete AM and FM bands. Those bands cover these frequencies: AM band: 530 to 1,710 kHz FM band: 87.7 to 107.9 MHz Radio stations on the AM band are assigned frequencies at least 10 kHz apart (530, 540, 550). Stations on the FM band are assigned frequencies at least 0.2 MHz apart (87.9, 88.1, 88.3). Stations must use these exact frequencies.
FM/AM Radio Reception As required by the FCC: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Features Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills. Your radio then receives both the direct signal from the station’s transmitter, and the deflected signal. This causes the sound to distort or flutter.
Remote Audio Controls MODE BUTTON VOL BUTTON CH BUTTON Three controls for the audio system are mounted in the steering wheel hub. These let you control basic functions without removing your hand from the wheel. The VOL button adjusts the volume up (▲) or down (▼). Press the top or bottom of the button, hold it until the desired volume is reached, then release it. The MODE button changes the mode. Pressing the button repeatedly selects FM1, FM2, AM, or disc (if a disc(s) is loaded).
Remote Audio Controls, Auxiliary Input Jack In MP3 or WMA mode, you can use the skip function to select folders. Press and hold the top (＋) of the CH button until you hear a beep, to skip forward to the first file of the next folder. Press the bottom (−) to skip backward to the previous folder. When playing a USB flash memory device, you can also use the seek function to skip the folder. To activate this, press and hold either side of the CH button until you hear a beep.
Radio Theft Protection Your vehicle’s audio system may disable itself if it is disconnected from electrical power for any reason. To make it work again, you must enter a specific five-digit code with the preset buttons. Because there are hundreds of number combinations possible from the five digits, making the system work without knowing the exact code is nearly impossible. You should have received a radio code card that lists your audio system’s code and serial numbers.
Setting the Clock On models without navigation system To set the time, press the CLOCK button until you hear a beep. The displayed time begins to blink. On models without navigation system Change the hours by pressing the H (hour) button until the numbers advance to the desired time. Change the minutes by pressing the M (minute) button until the numbers advance to the desired time. CLOCK BUTTON Features RESET BUTTON (PRESET 6) Press the CLOCK button again to enter the set time.
Setting the Clock On models without navigation system Adjusting the Clock with MENU Button You can also adjust the clock and switch the clock display between 24hours and 12-hours in the menu mode. To adjust the clock setting: 1. Press and release the MENU button. The display shows you the menu items. You can adjust the clock setting with the ignition switch in the ACCESSORY (I) or ON (II) position. 2. Turn the selector knob to select ‘‘CLOCK ADJUST.’’ 3.
Setting the Clock While setting the clock, pressing the RETURN button will go back to the previous display. Pressing the MENU button again will cancel this setting mode. Features MINUTE SETTING 5. Turn the selector knob to change the setting between 12H and 24H. 6. Press the selector knob (ENTER) to enter your selection. The display will return to the clock adjusting display. 7. To set the time, turn the selector knob and select the hours or the minutes, then press the knob to enter your selection.
Setting the Clock, Security System 10.To enter the clock setting, turn the selector knob to select ‘‘SET,’’ then press the knob. The display will return to the menu item display. 11.Press either the RETURN or MENU button to go back to the normal display. Security System The security system helps to protect your vehicle and valuables from theft.
Security System NOTE: Use the remote transmitter to quickly check that the hood, the trunk, and all doors are closed. Push the lock button twice within 5 seconds. There should be an audible confirmation beep. Do not attempt to alter this system or add other devices to it. Features With the system set, you can still open the trunk with the remote transmitter without triggering the alarm.
Compass On models without navigation system Compass Operation Compass operation can be affected by driving near power lines or stations, across bridges, through tunnels, over railroad crossings, past large vehicles, or driving near large objects that can cause a magnetic disturbance. It can also be affected by accessories such as antennas and roof racks that are mounted by magnets. Compass Calibration COMPASS COMPASS SETTING MENU ITEMS U.S. model is shown.
Compass 5. Press the selector knob (ENTER). The compass display is blinking and the CAL indicator is shown. 6. Drive the vehicle slowly in two complete circles. 3. Turn the selector knob to select ‘‘CALIBRATION.’’ 4. Press the selector knob (ENTER) to enter your selection. The display shows you ‘‘PUSH CAL START.’’ The audio system is not related to the compass system. Even if the compass system is calibrating, the display returns to the normal display which you last selected.
Compass Compass Zone Selection In most areas, there is a variation between magnetic north and true north. Zone selection is required so the compass can compensate for this variation. To check and select the zone, do this: 1. Turn the ignition switch to the ON (II) position. ZONE NUMBER 2. Press and hold the MENU button for about 5 seconds. The display shows you the compass setting menu items. 3. Turn the selector knob to select ‘‘ZONE.’’ Press the selector knob (ENTER) to enter your selection.
Compass The audio system is not related to the compass system. Even if the compass system is in the zone setting mode, the display returns to the normal display which you last selected.
Cruise Control Cruise control allows you to maintain a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It should be used for cruising on straight, open highways. It is not recommended for city driving, winding roads, slippery roads, heavy rain, or bad weather. Improper use of the cruise control can lead to a crash. Use the cruise control only when traveling on open highways in good weather.
Cruise Control Changing the Set Speed You can increase the set cruising speed in any of these ways: Press and hold the RES/ACCEL button. When you reach the desired cruising speed, release the button. Push on the accelerator pedal. Accelerate to the desired cruising speed, then press the SET/ DECEL button. To increase the speed in very small amounts, tap the RES/ ACCEL button. Each time you do this, your vehicle will speed up about 1 mph (1.6 km/h).
Cruise Control Even with the cruise control turned on, you can still use the accelerator pedal to speed up for passing. After completing the pass, take your foot off the accelerator pedal. The vehicle will return to the set cruising speed. Resting your foot on the brake or clutch pedal causes the cruise control to cancel. Canceling Cruise Control You can cancel cruise control in any of these ways: Tap the brake or clutch pedal. Push the CANCEL button on the steering wheel.
HomeLink Universal Transceiver The HomeLink Universal Transceiver built into your vehicle can be programmed to operate up to three remote controlled devices around your home, such as garage doors, lighting, or home security systems. If your garage door was manufactured before April 1, 1982, you may not be able to program HomeLink to operate it. These units do not have safety features that cause the motor to stop and reverse it if an obstacle is detected during closing, increasing the risk of injury.
HomeLink Universal Transceiver If you are training the second or third buttons, go directly to step 1.
HomeLink Universal Transceiver HomeLink is a registered trademark of Johnson Controls, Inc. Features As required by the FCC: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Bluetooth HandsFreeLink Bluetooth HandsFreeLink (HFL) allows you to place and receive phone calls using voice commands, without handling your cell phone. To use HFL, you need a Bluetoothcompatible cell phone. For a list of compatible phones, pairing procedures, and special feature capabilities: In the U.S., visit www.acura.com/ handsfreelink , or call (888) 528-7876. In Canada, visit www.acura.ca, or call (888) 9-ACURA-9.
Bluetooth HandsFreeLink Voice Control Tips MICROPHONE Press and release the HFL Talk button each time you want to make a command. After the beep, speak in a clear, natural tone. To change the volume level of HFL, use the audio system volume knob or the steering wheel volume controls. Vehicle with navigation system is shown. Air or wind noise from the dashboard and side vents, windows and moonroof may interfere with the microphone. Adjust or close them as necessary.
Bluetooth HandsFreeLink Help Features To hear general HFL information, including help on pairing a phone or setting up the system, say ‘‘Tutorial.’’ Information Display As an incoming call notification, you will see the following display: SIGNAL STRENGTH HFL MODE BATTERY LEVEL STATUS For help at any time, including a list of available commands, say ‘‘Hands free help.’’ ROAM STATUS PHONE NUMBER 306 2010 TSX Some phones may send battery, signal strength, and roaming status information to HFL.
Bluetooth HandsFreeLink Features BLUETOOTH INDICATOR BLUETOOTH INDICATOR On models without navigation system You will see ‘‘HANDSFREELINK’’ and the ‘‘ ’’ indicator on the audio display when you operate HFL. U.S. model is shown. On models with navigation system A notification that there is an incoming call, or HFL is in use, will appear on the navigation screen when the audio system is on.
Bluetooth HandsFreeLink How to Use HFL The ignition switch must be in the ACCESSORY (I) or ON (II) position.
Bluetooth HandsFreeLink Redial the last number called (See page 314) ‘‘Transfer’’ Transfer a call from HFL to your phone, or from your phone to HFL (See page 317) ‘‘Mute’’ Mute your voice to the person at the other end of the call (See page 317) ‘‘Send’’ Send numbers or names during a call (See page 317) Press HFL Talk button ‘‘Phonebook’’ Features ‘‘Redial’’ ‘‘Store’’ Store a phonebook entry (See page 318) ‘‘Edit’’ Edit the number of an existing phonebook entry (See page 318) ‘‘Delete’’ De
Bluetooth HandsFreeLink Apply a security passcode to the system that must be input at each key cycle to access the system (See page 324) ‘‘Security’’ ‘‘System Set up’’ ‘‘Change Passcode’’ Change your security passcode (See page 325) ‘‘Call Notification’’ Set how you would like to be notified of an incoming call (See page 325) ‘‘Auto Transfer’’ Press HFL Talk button ‘‘Clear’’ Set calls to automatically transfer from your phone to HFL when you enter the vehicle (See page 325) Clear the system of all
Bluetooth HandsFreeLink To use HFL, you need to pair your Bluetooth-compatible cell phone to the system. Phone Setup This command group is available for paired cell phones. On U.S. models with navigation system Once the pairing process is completed, AcuraLink may display a connection confirmation screen. This screen is used to create a data connection between your cell phone and the AcuraLink system. You can choose to set up the data connection now, or do it later.
Bluetooth HandsFreeLink To rename a paired phone: To delete a paired phone: Press and release the HFL Talk button before a command. Press and release the HFL Talk button before a command. 1. Say ‘‘Phone setup.’’ 1. Say ‘‘Phone setup.’’ 2. Say ‘‘Edit ’’ after the prompts. 2. Say ‘‘Delete’’ after the prompts. 3. If there is more than one phone paired to the system, HFL will ask you which phone’s name you want to change. Follow the HFL prompts and rename the phone. 3.
Bluetooth HandsFreeLink To hear which paired phone is currently linked: To change from the currently linked phone to another paired phone: Press and release the HFL Talk button before a command. Press and release the HFL Talk button before a command. 1. Say ‘‘Phone setup.’’ 1. Say ‘‘Phone setup.’’ 2. Say ‘‘Status’’ after the prompts. 2. Say ‘‘Next phone’’ after the prompts. To change the pairing code setting: Press and release the HFL Talk button before a command. 1. Say ‘‘Phone setup.’’ 3.
Bluetooth HandsFreeLink Making a Call You can make calls using any phone number or a name in the HFL phonebook. You can also redial the last number called. Bluetooth is the wireless technology that links your phone to HFL. HFL uses a Class 2 Bluetooth, which means the maximum range between your phone and vehicle is 30 feet (10 meters). During a call, HFL allows you to talk up to 30 minutes after you remove the key from the ignition switch. However, this may weaken the vehicle’s battery.
Bluetooth HandsFreeLink To make a call from an imported phonebook: Push up the interface selector to show a List. Features On models with navigation system 1. Press the INFO button, then select ‘‘Cellular Phonebook .’’ 2. Select ‘‘Search Imported Phonebook .’’ 3. Select a phonebook you want to choose a phone number from. If the phonebook you select is PINprotected, you will need to enter the PIN to access it. See page 322 for more information.
Bluetooth HandsFreeLink Selecting ‘‘Store in HandsFreeLink,’’ the phone number will be stored in HFL, so that you can call it using HFL’s name tag by voice. Receiving a Call When you receive a call, an incoming call notification (if activated) will play and interrupt the audio system if it is on. Press the HFL Talk button to answer the call, or the HFL Back button to hang up.
Bluetooth HandsFreeLink Muting a Call You can mute your voice to the person you are talking to during a call. Press and release the HFL Talk button and say ‘‘Transfer.’’ To mute your voice during a call, press and release the HFL Talk button and say ‘‘Mute.’’ To unmute your voice, press and release the HFL Talk button and say ‘‘Mute’’ again. Send Numbers or Names During a Call HFL allows you to send numbers or names during a call. This is useful when you call a menu-driven phone system.
Bluetooth HandsFreeLink Phonebook You can store up to 50 names with their associated numbers in HFL. The numbers you store cannot only be phone numbers but other types, such as account numbers or passwords, which can be sent during a menu-driven call. To store a phonebook entry: Press and release the HFL Talk button before a command. NOTE: Avoid using duplicate name entries. Avoid using ‘‘home’’ as a name entry. To edit the number stored in a name: Press and release the HFL Talk button before a command.
Bluetooth HandsFreeLink To list all names in the phonebook: Press and release the HFL Talk button before a command. 1. Say ‘‘Phonebook .’’ 1. Say ‘‘Phonebook .’’ 2. Say ‘‘Delete’’ after the prompts. 2. Say ‘‘List ’’ after the prompts. 3. Say the name you want to delete and follow the HFL prompts to complete the deletion. 3. HFL begins reading the names in the order they were stored.
Bluetooth HandsFreeLink Cellular Phonebook Import Cellular Phonebook: Search Imported Phonebook: (available on some phones) On models with navigation system The entire phonebook data of the cell phone that is linked to HFL can be imported to the navigation system. Once a phonebook has been imported, you can search the phone numbers by the person’s name. If you select Cellular Phonebook from the Information screen menu, you will see four HFL options.
Bluetooth HandsFreeLink Push up the interface selector to show a List. To search for a specific name in the phonebook, enter the keyword for either the first or last name. To display all names in the phonebook, select the ‘‘List ’’ option. Preference Fax Home Car Mobile Voice Work Other Features If the phonebook is PIN-protected, you will need to enter the 4-digit PIN. Select a person from the list.
Bluetooth HandsFreeLink Delete Imported Phonebook: You can delete any imported phonebook. After making a selection, the following screen will appear. PIN Number You can add, change, or remove a PIN number from any phonebook. Select ‘‘Delete Imported Phonebook ,’’ and a list of imported phonebooks will be displayed. Select a phonebook you want to delete. If the phonebook is PINprotected, you will need to enter the 4-digit PIN number. Select ‘‘Yes,’’ then ‘‘OK ’’ to complete the deletion.
Bluetooth HandsFreeLink To change the PIN to a new number: To remove a PIN: Select ‘‘PIN number,’’ then select ‘‘Do not use PIN’’ after you enter the current PIN. Features Select the phonebook you want. The display will change as shown above. The display will change as shown above. Enter the current PIN for this phonebook. Enter the new 4-digit PIN number. You will be asked to re-enter the PIN for verification.
Bluetooth HandsFreeLink System Setup This command group allows you to change or customize HFL basic settings. To set a 4-digit passcode to lock the HFL system for security purposes: Press and release the HFL Talk button before a command. 1. Say ‘‘System setup.’’ 2. Say ‘‘Security’’after the prompts. 3. Follow the HFL prompts and say the 4-digit passcode you want to set. 4. Follow the HFL prompts to confirm the number.
Bluetooth HandsFreeLink Press and release the HFL Talk button before a command. To change your security pass code: To select either a ring tone or a prompt as the incoming call notification＊: 1. Say ‘‘System setup.’’ Press and release the HFL Talk button before a command. 3. Follow the HFL prompts and say the new 4-digit passcode. 4. Follow the HFL prompts to confirm the number. 1. Say ‘‘System setup.
Bluetooth HandsFreeLink To clear the system: Quick Language Selection Change Language This operation clears the passcodes, paired phones, all names in the HFL phonebook, and all imported phonebook data. Canadian models only To quickly change the language: Press and release the HFL Talk button before a command. Canadian models only To change the system language between English and French: Press and release the HFL Talk button before a command. 1.
Bluetooth HandsFreeLink HFL Limitations An incoming call on HFL will interrupt Bluetooth Audio when it is playing. Audio will resume when the call is ended. U.S. models only In addition, you cannot use HFL while using AcuraLink. As required by the FCC: This device complies with Part 15 of the FCC rules.
AcuraLink (U.S. models only) On models with navigation system AcuraLink enhances your ownership experience by providing a direct communication link between your vehicle and the Acura Server. Working through the XM radio satellite, AcuraLink works in conjunction with the navigation system, Bluetooth HandsFreeLink (HFL), and audio system in your vehicle. It displays and receives several kinds of messages, including: Operating tips and information on your vehicle’s features.
AcuraLink (U.S. models only) To view previously read messages: Reading Messages If you have new messages, an envelope icon appears in the top right corner of the navigation screen. Features A list of all messages will be shown. New messages will be at the top. Select the message you want to read by pressing ENTER. To open a message: Press ENTER on the interface selector, then select New Messages from the navigation system map menu. Press the INFO button. The information screen will be shown.
AcuraLink (U.S. models only) Unread messages have a closed envelope icon next to them. The icon disappears when it has already been read. Message Options NOTE: Only Diagnostic Info messages appear on the navigation screen while driving. They indicate if your vehicle has a problem that may need immediate attention (see page 339 ). Select ‘‘Messages’’, then select a message category. Select the message you want to read and press ENTER. After purchasing your vehicle, messages may not appear immediately.
AcuraLink (U.S. models only) Delete − Select this option to delete the current message. Call − Select this option to call a phone number embedded in the message. When you select Call, the Bluetooth HandsFreeLink (HFL) dials the number for you. Call Your Dealer − Select this option to call the Acura dealer you purchased your vehicle from. AcuraLink also directs you to this dealer so you can schedule a maintenance appointment or receive information about a message.
AcuraLink (U.S. models only) Deleting Messages NOTE: Diagnostic info and recall/ campaign messages can only be deleted by your dealer. To delete a single message: Press the INFO button to bring up the Information screen. Scroll to the Messages option, then select it by pressing ENTER on the interface selector. Select the message category that contains the message you want to delete. To delete all messages: NOTE: The Delete All Messages command does not apply to Diagnostic Info and Recall messages.
AcuraLink (U.S. models only) Quick Tips Feature Guide These messages, based on updated vehicle information and comments from other TSX owners, supplement your Owner’s Manual. They provide you with relevant information for a safe and enjoyable ownership experience. For additional information, call Acura Client Services directly through HFL. During the first 90 days of ownership, a number of messages appears each day. These messages help you to use and understand the features of your vehicle.
AcuraLink (U.S. models only) Maintenance Minder You can use the following message options: Make an appointment from the schedule at the dealer. Reschedule the appointment with the dealer. Call your dealer for an appointment. Find the nearest dealer. These messages provide detailed information about the service needed for your vehicle. When a maintenance message appears on the multi-information display, a list of needed maintenance items is provided through an AcuraLink message.
AcuraLink (U.S. models only) Features When you see the maintenance minder message on the multiinformation display, you will also receive a message in the navigation screen. To open the message, press ENTER. Select ‘‘New Messages,’’ then press ENTER. You will see the list of all messages. The most recent message is listed at the top. Select the received message, then press ENTER. You will see the message as shown. To make an appointment, select ‘‘Schedule Dealer Appt.’’ then press ENTER.
AcuraLink (U.S. models only) Scheduled Dealer Appointment To reschedule the appointment: The confirmation message will be displayed on the screen. Make sure to confirm the appointment date, time and dealer. If it is OK, press ENTER. If you want to change or reschedule the appointment date, select ‘‘Cancel,’’ then press ENTER. Press the INFO button to go to the information screen. Select ‘‘Messages,’’ then select ‘‘Scheduled Dealer Appointment’’ from the message category list. Then press ENTER.
AcuraLink (U.S. models only) To cancel the appointment: Features Select ‘‘Messages’’ on the information screen, then press ENTER. Select ‘‘Scheduled Dealer Appointment’’ from the message category list. Then press ENTER. To cancel the appointment, select ‘‘Cancel Appointment,’’ then press ENTER. The system will request you to confirm the cancel on the navigation screen. To cancel the appointment, select ‘‘YES,’’ then press ENTER. If you select ‘‘NO,’’ the screen goes back to the previous message display.
AcuraLink (U.S. models only) If you select the cancel appointment, you cannot try to reschedule the appointment. If you want to change or reschedule the appointment date, call your dealer directly with HFL. Using automated appointment, your registered dealer through My Acura is automatically selected. If you want to select another dealer, such as in case of an emergency, find the nearest dealer and call the dealer directly with HFL.
AcuraLink (U.S. models only) For this reason, it is important that we retain your current phone number. Please update your information using My Acura at www.owners.acura.com. The AcuraLink system cannot determine some mechanical problems (such as squeaks or rattles) that are not triggered by the diagnostic indicator monitors. For more information on the instrument panel indicators, see page 60 .
AcuraLink (U.S. models only) If you want the information now, select the Check Now option. (If the navigation screen is not active, you must select OK from the navigation disclaimer screen before you can check the information.) Reminder Message Depending on the severity of the problem, the message will let you know if you should see your dealer immediately or if you can wait until a later date. You can then use the message options to call your dealer for an appointment or to find the nearest dealer.
AcuraLink (U.S. models only) Turning the Automated Appointment preference off will disable appointment notifications in the vehicle based on appointments created or changed at My Acura’s online scheduling website. AcuraLink/Message Screen To access the following functions, press the SETUP option, push the interface selector to the right to select Other, then rotate the interface knob to select AcuraLink/ Messages.
AcuraLink (U.S. models only) New Message Notification − Select ON if you want to be notified of new messages (envelope icon appears on the navigation screen). Select OFF if you do not want to be notified of new messages (envelope icon does not appear on the screen). Messages can still be accessed using the INFO menu. If you would like to stop receiving messages, visit the My Acura website at www.owners. acura.com to change your messaging preferences.
AcuraLink (U.S. models only) To find more information on Bluetooth compatible and enabled cell phones, visit www.acura.com/handsfreelink or call the HandsFreeLink consumer support at 1-888-528-7876. As required by the FCC: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Rearview Camera and Monitor On vehicles with navigation system REARVIEW CAMERA Whenever you shift to reverse (R) with the ignition switch in the ON (II) position, the rearview is shown on the navigation system screen. For the best picture, always keep the rearview camera clean, and do not cover the camera lens. To avoid scratching the lens when you clean it, use a moist, soft cloth. When in reverse, the navigation system ‘‘hard’’ buttons are locked out, except the ‘‘ ’’ button.
Before Driving Break-in Period .............................. 346 Fuel Recommendation .................. 346 Service Station Procedure ............ 347 Refueling..................................... 347 Tighten Fuel Cap Message ...... 349 Opening and Closing the Hood ........................................ 350 Oil Check .................................... 352 Engine Coolant Check .............. 353 Fuel Economy ................................ 354 Accessories and Modifications .... 357 Carrying Cargo ....
Break-in Period, Fuel Recommendation Break-in Period Help assure your vehicle’s future reliability and performance by paying extra attention to how you drive during the first 600 miles (1,000 km). During this period: Avoid full-throttle starts and rapid acceleration. Do not change the oil until the scheduled maintenance time. Avoid hard braking for the first 200 miles (300 km). Do not tow a trailer.
Service Station Procedure Some gasoline today is blended with oxygenates such as ethanol or MTBE. Your vehicle is designed to operate on oxygenated gasoline containing up to 10% ethanol by volume and up to 15% MTBE by volume. Do not use gasoline containing methanol. On vehicles with manual transmission You may hear a knocking noise from the engine if you drive the vehicle at low engine speed (below about 1,000 rpm) in a higher gear. To stop this, raise the engine speed by shifting to a lower gear.
Service Station Procedures FUEL FILL CAP Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. Stop the engine, and keep heat, sparks, and flame away. Handle fuel only outdoors. Wipe up spills immediately. 5. Stop filling the tank after the fuel nozzle automatically clicks off. Do not try to ‘‘top off’’ the tank. This leaves some room in the fuel tank for the fuel to expand with temperature changes. If the fuel nozzle keeps clicking off HOLDER TETHER 4.
Service Station Procedure 7. Push the fuel fill door closed until it latches. If the door won’t close fully, do not force it. Unlock the drivers door first. The f uel door and its latching mechanism can be permanently damaged if the f uel door is f orced closed when the driver’s door is locked. Tighten Fuel Cap Message off after several days of normal driving once you tighten or replace the fuel fill cap. To scroll to another message, press the INFO button.
Service Station Procedure If the hood latch handle moves stiffly, or if you can open the hood without lifting the handle, the mechanism should be cleaned and lubricated. Opening and Closing the Hood HOOD RELEASE HANDLE LATCH 1. Park the vehicle, and set the parking brake. Pull the hood release handle located under the lower left corner of the dashboard. The hood will pop up slightly. 2. Reach in between the hood and the front grille with your fingers. The hood latch handle is above the ‘‘A’’ logo.
Service Station Procedures GRIP SUPPORT ROD To close the hood, lift it up slightly to remove the support rod from the hole. Put the support rod back into its holding clip. Lower the hood to about a foot (30 cm) above the fender, then let it drop. Make sure it is securely latched. Before Driving CLIP 4-cylinder models 6-cylinder models 3. 4-cylinder models Holding the grip, pull the support rod out of its clip. Insert the end into the designated hole in the hood marked by an arrow.
Service Station Procedure Oil Check UPPER MARK LOWER MARK DIPSTICK (orange handle) 4-cylinder models Park the vehicle on a level surface. Wait a few minutes after turning the engine off before you check the oil. 6-cylinder models 3. Insert the dipstick all the way back into its hole. 1. Remove the dipstick (orange handle/loop). 2. Wipe the dipstick with a clean cloth or paper towel. 352 2010 TSX 4-cylinder models 4. Remove the dipstick again, and check the level.
Service Station Procedures Engine Coolant Check RESERVE TANK RESERVE TANK MAX LOWER MARK 6-cylinder models If it is near or below the lower mark, see Adding Engine Oil on page 415 . MAX MIN MIN 4-cylinder models Look at the coolant level in the radiator reserve tank. Make sure it is between the MAX and MIN lines. If it is below the MIN line, see Adding Engine Coolant on page 420 for information on adding the proper coolant. 6-cylinder models See page 413 for the engine coolant location.
Fuel Economy Actual Mileage and EPA Fuel Economy Estimates Comparison. Fuel economy is not a fixed number. It varies based on driving conditions, driving habits and vehicle condition. Therefore, it is not possible for one set of estimates to predict fuel economy precisely for all drivers in all environments. The EPA fuel economy estimates shown in the example to the right are a useful tool for comparison when buying a vehicle. EPA estimates include: City MPG − Represents urban driving in light traffic.
Fuel Economy Use the recommended viscosity motor oil, displaying the API Certification Seal (see page 416). Maintain proper tire inflation − An underinflated tire increases ‘‘rolling resistance,’’ which reduces fuel economy. Avoid carrying excess weight in your vehicle − It puts a heavier load on the engine, increasing fuel consumption. Drive Efficiently Drive moderately − Rapid acceleration, abrupt cornering, and hard braking increase fuel consumption.
Fuel Economy Minimize the use of the air conditioning system − The A/C puts an extra load on the engine which makes it use more fuel. Use the fresh-air ventilation when possible. Plan and combine trips − Combine several short trips into one. A warmed-up engine is more fuel efficient than a cold one.
Accessories and Modifications Modifying your vehicle, or installing some non-Acura accessories, can make your vehicle unsafe. Before you make any modifications or add any accessories, be sure to read the following information. Although non-Acura accessories may fit on your vehicle, they may not meet factory specifications, and could adversely affect your vehicle’s handling and stability.
Accessories and Modifications Modifying Your Vehicle Removing parts from your vehicle, or replacing components with nonAcura components could seriously affect your vehicle’s handling, stability, and reliability. Some examples are: Lowering the vehicle with a nonAcura suspension kit that significantly reduces ground clearance can allow the undercarriage to hit speed bumps or other raised objects, which could cause the airbags to deploy.
Carrying Cargo Your vehicle has several convenient storage areas: DOOR POCKETS CENTER POCKETS DRIVER’S POCKET GLOVE BOX Glove box Door and seat-back pockets Trunk, including the rear seats when folded down Before Driving Center and side pockets Driver’s pocket Console compartment SEAT-BACK POCKETS CONSOLE COMPARTMENT SIDE POCKET However, carrying too much cargo, or improperly storing it, can affect your vehicle’s handling, stability, stopping distance, and tires, and make it unsafe.
Carrying Cargo Load Limits The maximum load for your vehicle is 850 lbs (385 kg). See Tire And Loading Information label attached to the driver’s doorjamb. Label Example This figure includes the total weight of all occupants, cargo, and accessories, and the tongue load if you are towing a trailer. Overloading or improper loading can affect handling and stability and cause a crash in which you can be hurt or killed. Follow all load limits and other loading guidelines in this manual.
Carrying Cargo Example 1 Max Load (850 lbs) Passenger Weight (150 lbs x 2 = 300 lbs) Cargo Weight (550 lbs) Max Load (850 lbs) Passenger Weight (150 lbs x 4 = 600 lbs) Cargo Weight (250 lbs) Max Load (850 lbs) Passenger Weight (150 lbs x 5 = 750 lbs) Cargo Weight (100 lbs) In addition, the total weight of the vehicle, all occupants, accessories, cargo, and trailer tongue load must not exceed the Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Rating (GAWR).
Carrying Cargo Carrying Items in the Passenger Compartment Store or secure all items that could be thrown around and hurt someone during a crash. Keep the glove box closed while driving. If it is open, a passenger could injure their knees during a crash or sudden stop. Carrying Cargo in the Trunk Distribute cargo evenly on the floor of the trunk, placing the heaviest items on the bottom and as far forward as possible. Do not put any items on top of the trunk panel.
Carrying Cargo Cargo Hooks Cargo Net Optional HOOK The cargo net can be used to help hold down items stored in the trunk. Before Driving HOOK Cargo hook buttons in the trunk can be used to install a net for securing items.
364 2010 TSX
Driving This section gives you tips on starting the engine under various conditions, and how to operate the manual and automatic transmissions. It also includes important information on parking your vehicle, the braking system, the vehicle stability assist (VSA ) system, the tire pressure monitoring system (TPMS), and facts you need if you are planning to tow a trailer. 365 2010 TSX Driving Preparing to Drive ......................... 366 Starting the Engine (4-cylinder models) ...................
Preparing to Drive You should do these checks and adjustments before you drive your vehicle: 1. Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice. 6. Check the seat adjustment (see page 134 ). 7. Check the adjustment of the inside and outside mirrors (see page 145 ). 8. Check the steering wheel adjustment (see page 118 ). 2. Check that the hood is fully closed. 3. Check that the trunk is fully closed. 4. Visually check the tires.
Starting the Engine (4-cylinder models) 1. Apply the parking brake. 2. In cold weather, turn off all electrical accessories to reduce the drain on the battery. 3. Manual transmission: Press the clutch pedal down all the way. The START (III) position does not function unless the clutch pedal is pressed. Make sure the shift lever is in Park. Press on the brake pedal. The engine is harder to start in cold weather. Also, the thinner air f ound at altitudes above 8,000 f eet (2,400 meters) adds to this problem.
Starting the Engine (6-cylinder models) Your vehicle’s starting system has an auto control mode. When you turn the ignition switch to the START (III) position, this feature keeps the engine’s starter motor running until the engine starts. Follow these instructions to start the engine: seconds until the engine starts.
Starting the Engine (6-cylinder models) Check Starting System Message U.S. Driving If there is a problem with the starting system, you will see a ‘‘CHECK STARTING SYSTEM’’ message on the multi-information display when the ignition switch is turned to the ON (II) position. You will also see this message when the auto control mode of the starting system has a problem. Canada If this message is on, the ignition switch has to be held in the START (III) position manually until the engine starts.
Manual Transmission When shifting up or down, make sure you push the clutch pedal down all the way, shift to the next gear, and let the pedal up gradually. When you are not shifting, do not rest your foot on the clutch pedal. This can cause your clutch to wear out faster. On models with manual transmission The manual transmission is synchronized in all forward gears for smooth operation.
Manual Transmission Your vehicle is equipped with an aluminum shift lever. If you leave the vehicle parked outside for a long time on a hot day, be careful before moving the shift lever. Because of the heat, the shift lever may be extremely hot. If the outside temperature is low, the shift lever feels cold. Recommended Shift Points Drive in the highest gear that lets the engine run and accelerate smoothly. This will give you good fuel economy and effective emissions control.
Manual Transmission 2. If you are still unable to shift to reverse, apply the parking brake, and turn the ignition key to the ACCESSORY (I) or LOCK (0) position. Reverse Lockout The manual transmission has lockout so you cannot accidentally shift from any forward gear to reverse while the vehicle is moving at a certain speed. If you cannot shift to reverse when the vehicle is stopped, do the following: 3. Press the clutch pedal, and shift to reverse. 4.
Automatic Transmission Shift Lever Position Indicators If the malfunction indicator lamp comes on along with the ‘‘D’’ indicator, there is a problem with the automatic transmission control system. Avoid rapid acceleration, and have the transmission checked by your dealer as soon as possible. Shifting RELEASE BUTTON SHIFT LEVER These indicators in the tachometer show which position the shift lever is in.
Automatic Transmission To shift from: P to R R to P N to R D to S S to D D to N N to D R to N Do this: Press the brake pedal and press the shift lever release button. Press the shift lever release button. Move the shift lever. Park (P) − This position mechanically locks the transmission. Use Park whenever you are turning off or starting the engine. To shift out of Park, you must press on the brake pedal and have your foot off the accelerator pedal.
Automatic Transmission S Position (S) − To shift into the S position, press the release button on the front of the shift lever, and move the lever to S. This position is similar to D, except only gears from first to fourth are selected. The S position keeps the transmission from cycling between fourth and fifth gears in stop-and-go driving. Engine Speed Limiter If you exceed the maximum speed for the gear you are in, the engine speed will enter into the tachometer’s red zone.
Automatic Transmission 6. Remove the key from the shift lock release slot, then reinstall the cover. Make sure the notch on the cover is on the right side. Press the brake pedal, and restart the engine. If you need to use the shift lock release, it means your vehicle is developing a problem. Have it checked by your dealer. COVER 3. Put a cloth on the edge of the shift lock release slot cover to prevent scratches.
Driving with the Paddle Shifters Downshifting with the paddle shifter allows you to increase the engine braking when going down steep or long hills, and provides more power when climbing uphills. You can upshift the transmission manually to reduce the rpm. Using the Paddle Shifters in the D position (D-Paddle Shift Mode) When you are driving in the D position, you can shift the transmission up or down manually with the paddle shifters.
Driving with the Paddle Shifters The transmission control system monitors the accelerator pedal use and your driving conditions. When you press the accelerator pedal as in normal driving, the system judges that you are driving at a constant cruising speed without using the paddle shifters. Under these conditions, D-paddle shift mode is canceled, and the transmission automatically returns to drive mode (D). When the transmission returns to drive mode (D), the displayed gear number disappears.
Driving with the Paddle Shifters You upshift before the engine speed reaches the lowest threshold of the higher gear. You pull both paddle shifters at the same time. If there is a problem in the transmission while you are driving with the paddle shifters, the D indicator flashes, the D-paddle shift mode is canceled, and the transmission returns to drive mode (D).
Driving with the Paddle Shifters When you accelerate from a stop, the transmission starts in first gear, and you must manually upshift between first and fifth gears. Make sure you upshift before the engine speed reaches the tachometer’s red zone. Downshifting with the paddle shifter allows you to increase the engine braking when going down steep or long hills, and provides more power when climbing uphills. You can upshift the transmission manually to reduce the rpm.
Driving with the Paddle Shifters Here are the speed ranges for upshifting and downshifting.
Parking Always use the parking brake when you park your vehicle. Make sure the parking brake is set firmly, or your vehicle may roll if it is parked on an incline. If your vehicle has an automatic transmission, set the parking brake before you put the transmission in Park. This keeps the vehicle from moving and putting pressure on the parking mechanism in the transmission. Parking Tips Make sure the moonroof and the windows are closed.
Braking System Your vehicle is equipped with disc brakes at all four wheels. A power assist helps reduce the effort needed on the brake pedal. The emergency brake assist system increases the stopping force when you depress the brake pedal hard in an emergency situation. The anti-lock brake system (ABS) helps you retain steering control when braking very hard. Check the brakes after driving through deep water. Apply the brakes moderately to see if they feel normal.
Anti-lock Brakes (ABS) The anti-lock brake system (ABS) helps prevent the wheels from locking up, and helps you retain steering control by pumping the brakes rapidly, much faster than a person can do it. The electronic brake distribution (EBD) system, which is part of the ABS, also balances the front-to-rear braking distribution according to vehicle loading. You will feel a pulsation in the brake pedal when the ABS activates, and you may hear some noise.
Anti-lock Brakes (ABS) If the ABS indicator and the brake system indicator come on together, and the parking brake is fully released, the EBD system may also be shut down. The VSA indicator will come on along with the ABS indicator. A vehicle with ABS may require a longer distance to stop on loose or uneven surfaces, such as gravel or snow, than a vehicle without antilock.
Tire Pressure Monitoring System (TPMS) Your vehicle is equipped with a tire pressure monitoring system (TPMS) that turns on every time you start the engine and monitors the pressure in your tires while driving. Each tire has its own pressure sensor. If the air pressure of a tire becomes significantly low, the sensor in that tire immediately sends a signal that causes the low tire pressure/TPMS indicator in the instrument panel to come on.
Tire Pressure Monitoring System (TPMS) Although your tire pressure is monitored, you must manually check the tire pressures monthly. Tire Pressure Monitor Each tire, including the spare, should be checked monthly when the vehicle is cold, and set to the recommended inflation pressure as specified on the vehicle placard and in the owner’s manual (see page 447 ). To select the tire pressure monitor, press the INFO button several times with the ignition switch in the ON (II) position.
Tire Pressure Monitoring System (TPMS) U.S. model To see the inflation pressures of all four tires, press the SEL/RESET button. The display changes as shown above. Canadian model Each tire pressure is shown in PSI (U.S. models) or in kPa (Canadian models). 388 2010 TSX This shows that front left tire is losing pressure. Each tire has its own pressure sensor.
Tire Pressure Monitoring System (TPMS) TPMS System Failure If there is a problem with the TPMS, the tire pressure monitor shows a ‘‘SYSTEM FUNCTION ERROR’’ message and the tire pressure readings are not displayed. If this happens, you will first see a system warning message ‘‘CHECK TPMS SYSTEM’’ on the multi-information display. If there is a problem with the TPMS, you will see the above message on the multi-information display.
Tire Pressure Monitoring System (TPMS) Also, the low tire pressure/TPMS indicator begins to flash, then stays on (see page 387 ). If the low tire pressure/TPMS indicator comes on, or the multiinformation display shows a ‘‘CHECK TPMS SYSTEM’’ message, the VSA system automatically turns on even when the VSA system is turned off by pressing the VSA OFF switch (see page 393 ). If this happens, you cannot turn the VSA system off by pressing the VSA OFF switch again.
Tire Pressure Monitoring System (TPMS) Never use a puncture-repairing agent in a flat tire. If used, you will have to replace the tire pressure sensor. Have the flat tire repaired by your dealer as soon as possible. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Vehicle Stability Assist (VSA ), aka Electronic Stability Control (ESC), System The vehicle stability assist (VSA) system helps to stabilize the vehicle during cornering if the vehicle turns more or less than desired. It also assists you in maintaining traction while accelerating on loose or slippery road surfaces. It does this by regulating the engine’s output and by selectively applying the brakes.
Vehicle Stability Assist (VSA ), aka Electronic Stability Control (ESC), System Without VSA, your vehicle will have normal braking and cornering ability, but it will not have VSA traction and stability enhancement. VSA OFF Switch Press and hold the switch again. It turns the system back on. VSA is turned on every time you start the engine, even if you turned it off the last time you drove the vehicle. VSA and Tire Sizes Driving with varying tire or wheel sizes may cause the VSA to malfunction.
Towing a Trailer Your vehicle has been designed primarily to carry passengers and their cargo. You can also use it to tow a trailer if you carefully observe the load limits, use the proper equipment, and follow the guidelines in this section. Load Limits Break-In Period Avoid towing a trailer during your vehicle’s first 600 miles (1,000 km) (see page 346 ). Exceeding any load limit or improperly loading your vehicle and trailer can cause a crash in which you can be seriously hurt or killed.
Towing a Trailer To achieve a proper tongue load, start by loading 60% of the load toward the front of the trailer and 40% toward the rear, then re-adjust the load as needed.
Towing a Trailer Towing Equipment and Accessories Towing can require a variety of equipment, depending on the size of your trailer, how it will be used, how much load you are towing, and where you tow. To ensure the best quality, we recommend that you purchase Acura equipment whenever possible. Discuss your needs with your trailer sales or rental agency, and follow the guidelines in this section.
Towing a Trailer Trailer Lights Additional Towing Equipment Trailer lights and equipment must comply with federal, state, province, territory, and local regulations. Check with your local trailer sales or rental agencies for the requirements in the area where you plan to tow, and use only equipment designed for your vehicle. Many states and Canadian provinces/territories require special outside mirrors when towing a trailer.
Towing a Trailer The lights and brakes on your vehicle and the trailer are working properly. Your vehicle tires and spare are properly inflated, and the trailer tires and spare are inflated as recommended by the trailer maker. Driving Safely With a Trailer The added weight, length, and height of a trailer will affect your vehicle’s handling and performance, so driving with a trailer requires some special driving skills and techniques.
Towing a Trailer On models with automatic transmission Gear position Speed range 1 0 − 42 mph (0 − 67 km/h) 2, 3 19 − 62 mph (30 − 100 km/h) If the automatic transmission fluid temperature increases and exceeds the specified limit, the transmission will also automatically downshift to the first gear even with the Sequential Sportshift Mode. This prevents the automatic transmission from overheating.
Towing a Trailer If your vehicle has an automatic transmission, when driving down hills, reduce your speed and use the S mode. You can also use the paddle shifters to change the gear position. Select third, second or first gear depending on the vehicle speeds and road condition. When going down a steep hill, use second gear to provide greater engine braking. Shift down to first gear when driving up steep hills.
Maintenance This section explains why it is important to keep your vehicle well maintained and how to follow basic maintenance safety precautions. This section also includes instructions on how to read the maintenance minder messages on the multi-information display, and instructions for simple maintenance tasks you may want to take care of yourself.
Maintenance Safety All service items not detailed in this section should be performed by a certified technician or other qualified mechanic. Important Safety Precautions To eliminate potential hazards, read the instructions before you begin, and make sure you have the tools and skills required. Make sure your vehicle is parked on level ground, the parking brake is set, and the engine is off. To clean parts, use a commercially available degreaser or parts cleaner, not gasoline.
Maintenance Minder Your vehicle displays engine oil life and maintenance service items on the multi-information display to show you when you should have your dealer perform engine oil replacement and indicated maintenance service. Based on the engine operating conditions, the onboard computer in your vehicle calculates the remaining engine oil life and displays it as a percentage.
Maintenance Minder MAINTENANCE SUB ITEM CODE(S) Pressing either INFO button (▲/▼) switches the display from the message to another display. Once you switch the display, this message will go off. SUB ITEM(S) Along with the message, the system message indicator comes on (see page 67 ).
Maintenance Minder Pressing either INFO button (▲/▼) switches the display from the message to another display. Once you switch the display, this message will go off. Press the SEL/RESET button on the steering wheel repeatedly to select the engine oil life. The message ‘‘SERVICE,’’ along with ‘‘5%,’’ and the maintenance item code are displayed on the multi-information display when the calculated engine oil life is 1−5 percent (see page 403 ).
Maintenance Minder These messages will come on every time you turn the ignition switch to the ON (II) position. Immediately have the service performed, and make sure to reset the display as described on page 408 . Pressing either INFO button (▲/▼) switches the display from the message to another display. To see the message again, press either INFO button repeatedly.
Maintenance Minder TOTAL PAST DUE DISTANCE TRAVELED U.S. CANADA This message is displayed again when you drive over 10 miles (for U.S. models) or 10 km (for Canadian models) after seeing the 0% message. U.S. CANADA Immediately have the service performed, and make sure to reset the display as described on page 408 .
Maintenance Minder Maintenance Main Items and Sub Items MESSAGE DISPLAY MAINTENANCE MAIN ITEM ENGINE OIL LIFE DISPLAY MAINTENANCE SUB ITEMS All the maintenance items displayed in the multi-information display are in code. Resetting the Engine Oil Life Display Your dealer will reset the display after completing the required maintenance service. You will see ‘‘OIL LIFE 100%’’ on the display the next time you turn the ignition switch to the ON (II) position.
Maintenance Minder Important Maintenance Precautions If you have the required service done but do not reset the display, or reset the display without doing the service, the system will not show the correct maintenance intervals. This can lead to serious mechanical problems because you will no longer have an accurate record of when maintenance is needed. We recommend using Acura parts and fluids whenever you have maintenance done.
Maintenance Minder U.S. Vehicles: Maintenance, replacement, or repair of emissions control devices and systems may be done by any automotive repair establishment or individual using parts that are ‘‘certified’’ to EPA standards. According to state and federal regulations, failure to perform maintenance on the items marked with ＃ will not void your emissions warranties. However, all maintenance services should be performed in accordance with the intervals indicated by the multiinformation display.
Maintenance Minder Symbol A B Symbol 1 2 Maintenance Main Items Replace engine oil＊ Replace engine oil＊ and oil filter Inspect front and rear brakes Check parking brake adjustment Inspect these items: Tie rod ends, steering gearbox, and boots Suspension components Driveshaft boots Brake hoses and line (including ABS/VSA) All fluid levels and condition of fluids Exhaust system＃ Fuel lines and connections＃ Replace dust and pollen filter If you drive primarily in urban areas that have high concentrations of
Fluid Locations 4-cylinder models BRAKE FLUID (Black cap) CLUTCH FLUID (Manual Transmission only) (Light gray cap) ENGINE OIL DIPSTICK (Orange handle) ENGINE OIL FILL CAP WASHER FLUID (Blue cap) AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop) ENGINE COOLANT RESERVOIR RADIATOR CAP 412 2010 TSX
Fluid Locations 6-cylinder models ENGINE OIL DIPSTICK (Orange loop) BRAKE FLUID (Black cap) WASHER FLUID (Black cap) Maintenance AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop) ENGINE COOLANT RESERVOR＊ RADIATOR CAP＊ ＊ : Located under the cover ENGINE OIL FILL CAP 413 2010 TSX
Engine Compartment Covers 6-cylinder models only RIGHT ENGINE COMPARTMENT COVER The component parts in the engine compartment are protected by several covers. You may need to remove the covers when you perform some simple maintenance work. To remove the covers: 1. Remove the holding clip(s). 2. Remove the right and left engine compartment covers by pulling up. 3. Pull the bulkhead cover straight up to remove.
Adding Engine Oil Recommended Engine Oil Oil is a major contributor to your engine’s performance and longevity. Always use a premium-grade 5W-20 detergent oil displaying the API Certification Seal. This seal indicates the oil is energy conserving, and that it meets the American Petroleum Institute’s latest requirements. ENGINE OIL FILL CAP 4-cylinder models Reinstall the engine oil fill cap, and tighten it securely. Wait a few minutes, and recheck the oil level on the engine oil dipstick.
Adding Engine Oil Acura Motor Oil is the preferred 5W-20 lubricant for your vehicle. It is highly recommended that you use Acura Motor Oil in your vehicle for optimum engine protection. Make sure the API Certification Seal says ‘‘For Gasoline Engines.’’ The oil viscosity or weight is provided on the container’s label. 5W-20 oil is formulated for yearround protection of your vehicle to improve cold weather starting and fuel economy.
Changing the Engine Oil and Filter Always change the oil and filter according to the maintenance messages shown on the multiinformation display. The oil and filter collect contaminants that can damage your engine if they are not removed regularly. BOLT UNDER COVER 4-cylinder models 3. 4-cylinder models Remove the bolts located on the underside of the body with a wrench, then remove the under cover. 4-cylinder models WASHER 4. Remove the oil drain bolt and washer from the bottom of the engine.
Changing the Engine Oil and Filter OIL FILTER 6-cylinder models 4-cylinder models 5. Remove the oil filter and let the remaining oil drain. A special wrench (available from your dealer) is required. Make sure the oil filter gasket is not stuck to the contacting surface of the engine. If it is, remove it before installing a new oil filter. 418 2010 TSX 6-cylinder models 6. Install a new oil filter according to the instructions that come with it.
Changing the Engine Oil and Filter 7. Put a new washer on the drain bolt, then reinstall the drain bolt. Tighten it to: 29 lbf·ft (39 N·m , 4.0 kgf·m) 8. Refill the engine with the recommended oil. Engine oil change capacity (including filter): 4-cylinder models 4.2 US qt (4.0 ) 10.Let the engine run for several minutes, then check the drain bolt and oil filter for leaks. Improper disposal of engine oil can be harmf ul to the environment.
Engine Coolant Adding Engine Coolant 4-cylinder models RESERVE TANK If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to the MAX line. Inspect the cooling system for leaks. 6-cylinder models If Honda antifreeze/coolant is not available, you may use another major-brand non-silicate coolant as a temporary replacement. Make sure it is a high-quality coolant recommended for aluminum engines.
Engine Coolant If the reserve tank is completely empty, you should also check the coolant level in the radiator. RADIATOR CAP RADIATOR CAP COVER Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you. 4-cylinder models 1. Make sure the engine and radiator are cool. 6-cylinder models 2. 6-cylinder models Remove the radiator cap cover. 3. Relieve any pressure in the cooling system by turning the radiator cap counterclockwise, without pressing down.
Engine Coolant, Windshield Washers RADIATOR CAP 5. The coolant level should be up to the base of the filler neck. Add coolant if it is low. Pour the coolant slowly and carefully so you do not spill any. Clean up any spill immediately; it could damage components in the engine compartment. Windshield Washers Check the fluid level in the windshield washer reservoir at least monthly during normal use. LEVEL GAUGE 6. Put the radiator cap back on, and tighten it fully. 6-cylinder models 4.
Windshield Washers, Transmission Fluid Fill the reservoir with a good-quality windshield washer fluid. This increases the cleaning capability and prevents freezing in cold weather. Automatic Transmission When you refill the reservoir, clean the edges of the windshield wiper blades with windshield washer fluid on a clean cloth. This will help to condition the blade edges.
Transmission Fluid GUIDE UPPER MARK LOWER MARK UPPER MARK LOWER MARK DIPSTICK 6-cylinder models 2. Remove the dipstick (yellow loop) from the transmission, and wipe it with a clean cloth. 4-cylinder models 3. Insert the dipstick all the way back into the transmission securely as shown in the illustration. 424 2010 TSX 6-cylinder models 4. Remove the dipstick and check the fluid level. It should be between the upper and lower marks.
Transmission Fluid 5. If the level is below the lower mark, add fluid into the dipstick hole to bring it to the level between the upper and lower marks. Pour the fluid slowly and carefully so you do not spill any. Clean up any spill immediately; it could damage components in the engine compartment. 4-cylinder models Make sure the rubber cap on the dipstick fits in the dipstick guide and that you push the dipstick in all the way.
Transmission Fluid Manual Transmission FILLER BOLT BOLT UNDER COVER Check the fluid level with the transmission at normal operating temperature and the vehicle sitting on level ground. To check the transmission fluid level, remove the bolts with a wrench, then remove the under cover carefully. Correct level Remove the transmission filler bolt, and carefully feel inside the bolt hole with your finger. The fluid level should be up to the edge of the bolt hole.
Brake and Clutch Fluid Check the fluid level in the reservoirs monthly. There are up to two reservoirs, depending on the model. They are: Brake fluid reservoir (all models) Clutch fluid reservoir (manual transmission models only) Replace the brake fluid every 3 years, independent of the maintenance message in the multi-information display. Using any non-Acura brake fluid can cause corrosion and decrease the life of the system.
Brake and Clutch Fluid, Timing Belt Clutch Fluid Timing Belt Manual Transmission only 6-cylinder models The timing belt should be replaced according to the maintenance minder (see page 411 ). MAX Replace the timing belt every 60,000 miles (U.S.) or every 100,000 km (Canada) if you regularly drive your vehicle in any of the following conditions: 6-cylinder models MIN MAX MIN The fluid level should be between the MIN and MAX marks on the side of the reservoir.
Lights Headlight Aiming The headlights were properly aimed when your vehicle was new. If you regularly carry heavy items in the trunk or pull a trailer, readjustment may be required. Adjustments should be done by your dealer or another qualified technician. Low Beam Headlight Bulb Replacement All models except Canadian TSX with 4-cylinder engine High beam headlights on all models Low beam headlights on Canadian TSX with 4-cylinder engine Your vehicle has halogen headlight bulbs.
Lights Low Beam Headlight Canadian TSX with 4-cylinder engine HOLDING CLIP COVER 1. To change the passenger’s side bulb, start the engine, turn the steering wheel all the way to the left, and turn off the engine. To change the driver’s side bulb, turn the steering wheel to the right. TAB SCREW 2. Use a flat-tip screwdriver to remove the holding clip from the inner fender, and remove the screw with a Phillips-head screwdriver. 430 2010 TSX 3.
Lights 7. Insert the new bulb into the hole, making sure the tabs are in their slots. High Beam Headlights 8. Push the electrical connector onto the new bulb. Make sure it is connected securely. 9. Pivot the hold-down wire back in place, and clip the end into the slot. 6. Remove the electrical connector from the bulb by pulling the connector straight back, then remove the bulb. STAY 4-cylinder models 1. Open the hood. 11.Turn on the headlights to test the new bulb. 12.
Lights COVER COVER 6-cylinder models STAY 4-cylinder models AIR INTAKE DUCT 6-cylinder models 4-cylinder models 6-cylinder models To change a bulb on the left side, remove the two fasteners by turning the head of each fastener with a flat-tip screwdriver, then remove the cover and upper part of the air intake duct. Remove the fasteners, then remove the air intake duct cover.
Lights 6. Install the new bulb, and turn it one-quarter turn clockwise to lock it in place. 7. Push the electrical connector back onto the bulb. Make sure it is on all the way. 8. Turn on the headlights to test the new bulb. 4-cylinder models 5. Remove the bulb by turning it approximately one-quarter turn counterclockwise. 9. On the passenger’s side Reinstall the coolant reserve tank. On the driver’s side 4-cylinder models: Reinstall the cover and upper part of the air intake duct securely.
Lights Replacing a Front Turn Signal/ Parking and Side Marker Light Bulb 1. To change the bulb on the driver’s side, start the engine, turn the steering wheel all the way to the right, then turn off the engine. To change the bulb on the passenger’s side, turn the steering wheel to the left. HOLDING CLIP SCREW 2. Use a flat-tip screwdriver to remove the holding clip from the inner fender, and remove the screw with a Phillips-head screwdriver. 3. Pull the inner fender cover away from the fender and bumper.
Lights 6. Install the new bulb and turn it clockwise to lock it in place. Replacing Rear Bulbs (In Fenders) 7. Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place. 8. Turn on the lights to make sure the new bulb is working. COVER 1. Open the trunk. 2. Remove the light assembly cover by pulling its outside edge. 3. Determine which of the three bulbs is burned out: stop/taillight, rear side-marker, or turn signal light. 4.
Lights 5. Push a new bulb straight into the socket until it bottoms, and reinstall the socket into the light assembly by turning it clockwise until it locks. Replacing a Back-up Light Bulb (in Trunk Lid) 6. Test the new bulb to make sure it works. 7. Reinstall the light assembly cover. FASTENERS 1. Open the trunk. 2. To replace a bulb on either side, remove the two fasteners on the left side, or a fastener on the right side. 436 2010 TSX 3.
Lights SOCKET 6. Insert the socket back into the light assembly. Turn it clockwise to lock it in place. 7. Turn on the lights to make sure the new bulb is working. 8. Reinstall the trunk lid lining. Make sure it is installed under the edge of the trunk seal. Side Turn Signal Lights Each outside mirror has side turn signal lights. The lights should be replaced by your dealer. Rear License Plate Light Bulbs The license plate has two lights above it. The bulbs should be replaced by your dealer. 9.
Lights Replacing the High-mount Brake Light 3. Reinstall the socket. Turn it clockwise until it locks. Make sure the new bulb is working. 1. Open the trunk, and remove the socket from the light assembly by turning it one-quarter turn counterclockwise. 2. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms.
Lights Replacing a Fog Light Bulb HOLDING CLIPS If equipped Your vehicle uses halogen light bulbs. When replacing a bulb, handle it by its plastic case, and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth. Halogen bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter. UNDER COVER 1. Remove the three holding clips with a flat-tip screwdriver. 2.
Lights 5. Install the new bulb into the hole and turn it one-quarter turn clockwise to lock it in place. 6. Push the electrical connector back onto the bulb. Make sure it is on all the way. 7. Turn on the fog lights to test the new bulb. 8. Reinstall the holding clips, and push in the head of each clip. 3. Remove the electrical connector from the bulb by pushing on the tab and pulling the connector down. 4. Remove the bulb from the fog light assembly by turning it onequarter turn counterclockwise.
Cleaning the Seat Belts, Floor Mats Cleaning the Seat Belts OPENING Dirt build-up around the openings of the seat belt anchors can cause the belts to retract slowly. Wipe the openings with a clean cloth dampened in mild soap and warm water or isopropyl alcohol. Floor Mats To unlock Driver’s floor mat is shown. The driver’s floor mat that came with your vehicle hooks over the floor mat anchors. To lock each anchor, turn the knob clockwise.
Floor Mats, Dust and Pollen Filter, Exterior Care If you remove a floor mat, make sure to re-anchor it when you put it back in your vehicle. If you use a non-Acura floor mat, make sure it fits properly and that it can be used with the floor mat anchors. Do not put additional floor mats on top of the anchored mats. Make sure the rear floor mats are properly positioned. If not, the floor mat will interfere with the seat operation and make the front passenger’s weight sensors ineffective.
Wiper Blades Check the condition of the wiper blades at least every six months. Replace them if you find signs of cracking in the rubber, areas that are getting hard, or if they leave streaks and unwiped areas when used. WIPER BLADES LOCK TAB 1. Raise each wiper arm off the windshield, lifting the driver’s side first, then the passenger’s side. 2.
Wiper Blades Pivot the blade assembly toward the wiper arm until it releases from the wiper arm. 4. Examine the new wiper blades. If they have no plastic or metal reinforcement along the back edge, remove the metal reinforcement strips from the old wiper blade, and install them in the slots along the edge of the new blade. BLADE When replacing a wiper blade, make sure not to drop the wiper blade or wiper arm down on the windshield. REINFORCEMENT BLADE TOP 3.
Wiper Blades 6. Slide the wiper blade assembly onto the wiper arm. Push down the lock tab. Make sure the wiper blade assembly locks in place. TAB 7. Lower the wiper arm down against the windshield, the passenger’s side first, then the driver’s side. INDENT Maintenance 5. Place the top of the wiper blade on the end of the blade assembly, and slide the blade onto the assembly in the direction pointed to by the arrow.
Tires To safely operate your vehicle, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated. The following pages give more detailed information on how to take care of your tires and what to do when they need to be replaced. Using tires that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed. Follow all instructions in this owner’s manual regarding tire inflation and maintenance.
Tires If you check air pressures when the tires are hot (driven for several miles/kilometers), you will see readings 4 to 6 psi (30 to 40 kPa, 0.3 to 0.4 kgf/cm ) higher than the cold readings. This is normal. Do not let air out to match the recommended cold air pressure. The tire will be underinflated. P225/50R17 93V Tire Size P235/45R18 94V Cold Tire Pressure for Normal Driving Front/Rear: 33 psi (230 kPa , 2.
Tires High Speed Driving We strongly recommend that you do not drive faster than the posted speed limits and conditions allow. If you ever drive in a sanctioned competitive event at sustained high speeds (over 118 mph or 190 km/h), be sure to adjust the cold tire pressures as shown below. If you do not, excessive heat can build up and cause sudden tire failure. 4-cylinder models Tire Size P225/50R17 93V Cold Tire Pressure 35 psi (240 kPa , 2.
Tires Tire Service Life The service life of your tires is dependent on many factors, including, but not limited to, driving habits, road conditions, vehicle loading, inflation pressure, maintenance history, speed, and environmental conditions (even when the tires are not in use). The last four digits of the TIN (tire identification number) are found on the sidewall of the tire and indicate the date of manufacture (See Tire Labeling on page 496 ).
Tires Tire Rotation Front (For non-directional (For directional tires and wheels) tires and wheels) Replacing Tires and Wheels Replace your tires with radial tires of the same size, load range, speed rating, and maximum cold tire pressure rating (as shown on the tire’s sidewall). Mixing radial and bias-ply tires on your vehicle can reduce braking ability, traction, and steering accuracy.
Tires If you ever replace a wheel, make sure that the wheel’s specifications match those of the original wheels. Also be sure you use only TPMS specific wheels. If you do not, the tire pressure monitoring system will not work. Replacement wheels are available at your dealer. Wheel and Tire Specifications Wheels: 4-cylinder models: 17 x 7 1/2J 6-cylinder models: 18 x 8J Tires: 4-cylinder models: P225/50R17 93V Installing improper tires on your vehicle can affect handling and stability.
Tires Tire Chains Mount tire chains on your tires when required by driving conditions or local laws. Install them only on the front tires. Because your vehicle has limited tire clearance, Acura strongly recommends using the chains listed below, made by Security Chain Company (SCC). Cable-type : SCC Radial Chain hear them coming into contact with the body or chassis, stop and investigate. Remove them as soon as you begin driving on cleared roads.
Checking the Battery TEST INDICATOR WINDOW 4-cylinder models 6-cylinder models 6-cylinder models To see the battery label, remove the left side engine compartment cover (see page 414 ). Check the terminals for corrosion (a white or yellowish powder). To remove it, cover the terminals with a solution of baking soda and water. It will bubble up and turn brown. When this stops, wash it off with plain water. Dry off the battery with a cloth or paper towel.
Checking the Battery, Vehicle Storage If you need to connect the battery to a charger, disconnect both cables to prevent damaging your vehicle’s electrical system. Always disconnect the negative (−) cable first, and reconnect it last. The battery gives off explosive hydrogen gas during normal operation. A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you. Wear protective clothing and a face shield, or have a skilled technician do the battery maintenance.
Vehicle Storage Leave the parking brake off. Put the transmission in reverse (manual) or Park (automatic). Support the front wiper blade arms with a folded towel or rag so they do not touch the windshield. Block the rear wheels. To minimize sticking, apply a silicone spray lubricant to all door and trunk seals. Also, apply a vehicle body wax to the painted surfaces that mate with the door and trunk seals.
456 2010 TSX
Taking Care of the Unexpected This section covers the more common problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your vehicle towed. Compact Spare Tire....................... 458 Changing a Flat Tire ..................... 459 If the Engine Won’t Start ..........
Compact Spare Tire Use the compact spare tire as a temporary replacement only. Get your regular tire repaired or replaced, and put it back on your vehicle as soon as you can. Check the air pressure of the compact spare tire every time you check the other tires. It should be inflated to: 60 psi (420 kPa , 4.2 kgf/cm ) Follow these precautions: Never exceed 50 mph (80 km/h). This tire gives a harsher ride and less traction on some road surfaces. Use greater caution while driving.
Changing a Flat Tire If you have a flat tire while driving, stop in a safe place to change it. Drive slowly along the shoulder until you get to an exit or an area that is far away from the traffic lanes. The vehicle can easily roll off the jack, seriously injuring anyone underneath. 1. Park the vehicle on firm, level, and non-slippery ground. Put the transmission in Park (automatic) or reverse (manual). Apply the parking brake. TRUNK FLOOR LID 2.
Changing a Flat Tire JACK SPARE TIRE JACK WHEEL NUT WRENCH TOOL KIT CASE 4. Take the tool kit case out of the trunk. 6. Take the jack out of the tool kit case. 5. Unscrew the wing bolt and take the spare tire out of its well. 460 2010 TSX 7. Loosen each wheel nut 1/2 turn with the wheel nut wrench.
Changing a Flat Tire EXTENSION JACKING POINT 9. Use the extension and the wheel nut wrench as shown to raise the vehicle until the flat tire is off the ground. 10.Remove the wheel nuts, then remove the flat tire. Handle the wheel nuts carefully; they may be hot from driving. Place the flat tire on the ground with the outside surface facing up. BRAKE HUB 11.Before mounting the spare tire, wipe any dirt off the mounting surface of the wheel and hub with a clean cloth.
Changing a Flat Tire 12.Put on the spare tire. Put the wheel nuts back on finger-tight, then tighten them in a crisscross pattern with the wheel nut wrench until the wheel is firmly against the hub. Do not try to tighten the wheel nuts fully. 13.Lower the vehicle to the ground, and remove the jack. CENTER CAP 14.Tighten the wheel nuts securely in the same crisscross pattern. Have the wheel nut torque checked at the nearest automotive service facility.
Changing a Flat Tire SPACER CONE WING BOLT For normal tire For compact spare tire SPACER CONE 16.Place the flat tire face down in the spare tire well. Loose items can fly around the interior in a crash and could seriously injure the occupants. TAB To remove the spacer cone, squeeze the tabs on the wing bolt to disengage it from the center of the spacer cone, then pull the bolt downward. To install the wing bolt to the spacer cone, reverse this procedure. 18.
If the Engine Won’t Start Diagnosing why the engine won’t start falls into two areas, depending on what you hear when you turn the ignition switch to the START (III) position: You hear nothing, or almost nothing. The engine’s starter motor does not operate at all, or operates very slowly. You can hear the starter motor operating normally, or the starter motor sounds like it is spinning faster than normal, but the engine does not start up and run.
If the Engine Won’t Start The Starter Operates Normally In this case, the starter motor’s speed sounds normal, or even faster than normal, when you turn the ignition switch to the START (III) position, but the engine does not run. Are you using a properly coded key? An improperly coded key will cause the immobilizer system indicator in the instrument panel to blink rapidly (see page 121 ). Do you have fuel? Check the fuel gauge; the low fuel indicator may not be working.
Jump Starting Although this seems like a simple procedure, you should take several precautions. A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby. Keep all sparks, open flames, and smoking materials away from the battery. You cannot start your vehicle with an automatic transmission by pushing or pulling it. To jump start your vehicle: 1. Open the hood, and check the physical condition of the battery.
Jump Starting 4-cylinder models 6-cylinder models BOOSTER BATTERY BOOSTER BATTERY 4. Connect one jumper cable to the positive (＋) terminal on your battery. Connect the other end to the positive (＋) terminal on the booster battery. 5. 4-cylinder models Connect the second jumper cable to the negative (−) terminal on the booster battery. Connect the other end to the engine mounting bolt (automatic) or the transmission mounting bolt (manual), as shown.
Jump Starting 6. If the booster battery is in another vehicle, have an assistant start that vehicle and run it at a fast idle. 7. Start the vehicle. If the starter motor still operates slowly, check that the jumper cables have good metal-to-metal contact. 4-cylinder models with manual transmission 6-cylinder models 6-cylinder models Connect the second jumper cable to the negative (−) terminal on the booster battery. Connect the other end to the engine hanger as shown.
If the Engine Overheats The pointer of the vehicle’s temperature gauge should stay in the midrange. If it climbs to the red mark, you should determine the reason (hot day, driving up a steep hill, etc.). You will also see a ‘‘WATER TEMP HOT’’ message on the multiinformation display (see page 69 ). Driving with the temperature gauge pointer at the red mark can cause serious damage to the engine. Do not open the hood if steam is coming out. 1. Safely pull to the side of the road.
If the Engine Overheats 6. If you don’t find an obvious leak, check the coolant level in the radiator reserve tank (see page 353 ). Add coolant if the level is below the MIN mark. 7. If there was no coolant in the reserve tank, you may need to add coolant to the radiator. Let the engine cool down until the pointer reaches the middle of the temperature gauge or lower before checking the radiator. Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.
Low Oil Pressure Indicator, Charging System Indicator Low Oil Pressure Indicator This indicator should never come on when the engine is running. If it starts flashing or stays on, the oil pressure has dropped very low or lost pressure. Serious engine damage is possible, and you should take immediate action. You will also see a ‘‘CHECK ENGINE OIL LEVEL’’ message on the multi-information display when this indicator comes on. 2. Let the vehicle sit for a minute.
Malfunction Indicator Lamp If this indicator comes on while driving, it means one of the engine’s emissions control systems may have a problem. Even though you may feel no difference in your vehicle’s performance, it can reduce your fuel economy and cause increased emissions. Continued operation may cause serious damage. If you have recently refueled your vehicle, the indicator coming on could be due to a loose or missing fuel fill cap. Tighten the cap until it clicks at least once.
Brake System Indicator U.S. Canada The brake system indicator normally comes on when you turn the ignition switch to the ON (II) position, and as a reminder to check the parking brake. It will stay on if you do not fully release the parking brake. You will also see a ‘‘BRAKE FLUID LOW’’ message on the multiinformation display. However, if the brake pedal does not feel normal, you should take immediate action.
Opening the Fuel Fill Door Manually COVER RELEASE LEVER If there is a problem with the power door lock system and you cannot unlock the driver’s door, use the release lever behind the left side cover in the trunk. To open the fuel fill door, pull the release lever rearward. If you also cannot unlock the trunk due to the power door lock system malfunction, see page 132 and open the trunk manually.
Fuses INTERIOR (Driver’s side) INTERIOR (Passenger’s side) UNDER-HOOD TAB NOTCH FUSE LABEL 4-cylinder models FUSE BOX The vehicle’s fuses are contained in three fuse boxes. The under-hood fuse box is on the driver’s side. To open it, push the tabs as shown. CONTINUED 475 2010 TSX Taking Care of the Unexpected The driver’s side interior fuse box is under the dashboard on the driver’s side. The fuse label is attached to the side panel.
Fuses UNDER-HOOD TAB 6-cylinder models Checking and Replacing Fuses If something electrical in your vehicle stops working, the first thing you should check for is a blown fuse. Determine from the chart on pages 479 , 480 and 481 , or the diagram on the fuse box lid or the fuse label, which fuse or fuses control that component. Check those fuses first, but check all the fuses before deciding that a blown fuse is not the cause. Replace any blown fuses and check if the device works. 1.
Fuses BLOWN Also check the combined fuse box in the under-hood fuse box. FUSE PULLER 5. Look for a blown wire inside the fuse. If it is blown, replace it with one of the spare fuses of the same rating or lower. CONTINUED 477 2010 TSX Taking Care of the Unexpected 4. Check the smaller fuses in the under-hood fuse box and all the fuses in the interior fuse boxes by pulling out each one with the fuse puller provided on the back of the under-hood fuse box cover.
Fuses If you cannot drive the vehicle without fixing the problem, and you do not have a spare fuse, take a fuse of the same rating or a lower rating from one of the other circuits. Make sure you can do without that circuit temporarily (such as the accessory power socket). FUSE PULLER SPARE FUSES Your vehicle has spare fuses on the back of the under-hood fuse box cover. If you replace the blown fuse with a spare fuse that has a lower rating, it might blow out again.
Fuse Locations UNDER-HOOD FUSE BOX Amps. 100 A＊1 120 A＊2 40 A 70 A (40 A) 30 A − 30 A − 1−2 2−1 2−2 2−3 2−4 2−5 2−6 Circuits Protected Battery Passenger’s Side Fuse Box EPS Passenger’s Side Fuse Box ABS/VSA FSR Not Used ABS/VSA Motor Not Used No. Amps.
Fuse Locations No. Amps. INTERIOR FUSE BOX (Driver’s Side) No. Amps. 1 2 3 4 5 6 7 8 − (7.5 A) 15 A 10 A 7.5 A 7.5 A 15 A (7.5 A) Circuits Protected Not Used Seat Memory Washer Wiper Meter ABS/VSA ACG STS＊1, Starter DIAG＊2 No. Amps. 9 10 11 12 20 A (10 A) 10 A 7.5 A 13 14 15 (7.5 A) − 7.5 A Circuits Protected Fuel Pump VB SOL ＊3 SRS ODS (Occupant Detection System) IG1＊1, STS＊2 Not Used Daytime Running Lights 480 2010 TSX 16 17 18 19 20 21 22 7.5 A 7.5 A 7.
Fuse Locations No. Amps. INTERIOR FUSE BOX (Passenger’s Side) 15 16 17 18 19 20 21 22 ＊: 1 2 10 A 10 A 3 4 5 6 7 8 (10 A) 15 A − 7.5 A − (20 A) Circuits Protected Right Headlight High Beam Right Side Small Lights (Exterior) Right Front Fog Light＊ Right Headlight Low Beam Not Used Interior Lights Not Used Passenger’s Side Power Seat Reclining No. Amps.
Emergency Towing If your vehicle needs to be towed, call a professional towing service or organization. Never tow your vehicle with just a rope or chain. It is very dangerous. There are two ways to tow your vehicle: Flat-bed Equipment − The operator loads your vehicle on the back of a truck. This is the best way to transport your vehicle. Wheel-lift Equipment − The tow truck uses two pivoting arms that go under the front tires and lift them off the ground. The rear tires remain on the ground.
Emergency Towing Trying to lif t or tow your vehicle by the bumpers will cause serious damage. The bumpers are not designed to support the vehicle’s weight. The steering system can be damaged if the steering wheel is locked. Leave the ignition switch in the ACCESSORY (I) position, and make sure the steering wheel turns f reely bef ore you begin towing.
484 2010 TSX
Technical Information The diagrams in this section give you the dimensions and capacities of your vehicle and the locations of the identification numbers. It also includes information you should know about your vehicle’s tires and emissions control systems. Identification Numbers ................. 486 Specifications (4-cylinder models) ................... 488 Specifications (6-cylinder models) ................... 491 DOT Tire Quality Grading (U. S. Vehicles) .......................... 494 Tire Labeling ...
Identification Numbers Your vehicle has several identifying numbers in various places. VEHICLE IDENTIFICATION NUMBER (VIN) The vehicle identification number (VIN) is the 17-digit number your dealer uses to register your vehicle for warranty purposes. It is also necessary for licensing and insuring your vehicle. The easiest place to find the VIN is on a plate fastened to the top of the dashboard. You can see it by looking through the windshield on the driver’s side.
Identification Numbers The engine number is stamped into the front of the engine block. 4-cylinder models AUTOMATIC TRANSMISSION NUMBER 6-cylinder models You can see the engine number through the window on the front bulkhead cover. ENGINE NUMBER The transmission number is on a label on top of the transmission.
Specifications (4-cylinder Models) Dimensions Length Width Height Wheelbase Track Front Rear Capacities Engine coolant 185.6 in (4,715 mm) 72.4 in (1,840 mm) 56.7 in (1,440 mm) 56.7 in (1,439 mm) ＊ 106.5 in (2,705 mm) 62.2 in (1,580 mm) 62.2 in (1,580 mm) ＊ : Canadian TSX Weights Gross vehicle weight rating Seating Capacities Total Front Rear Air Conditioning Refrigerant type Charge quantity Lubricant type Capacities Fuel tank See the certification label attached to the driver’s doorjamb.
Specifications (4-cylinder Models) Battery Capacity Fuses Interior 12 V − 36 AH/5 HR 12 V − 45 AH/20 HR 12 V − 47 AH/20 HR Driver’s side Passenger’s side Under-hood Engine Type Water cooled 4-stroke, DOHC i-VTEC 4-cylinder, gasoline engine 3.43 x 3.90 in (87.0 x 99.0 mm) 144 cu-in (2,354 cm ) 11.
Specifications (4-cylinder Models) Alignment Toe-in Camber Caster Tires Size Pressure Front Rear Front Rear Front Front/Rear Spare Front/Rear Spare 0.00 in (0.0 mm) 0.08 in (2.0 mm) 0° −1° 3°48’ P225/50R17 93V T135/80D16 101M 33 psi (230 kPa , 2.3 kgf/cm ) 60 psi (420 kPa , 4.
Specifications (6-cylinder Models) Dimensions Length Width Height Wheelbase Track Front Rear Weights Gross vehicle weight rating Seating Capacities Total Front Rear Capacities Fuel tank See the certification label attached to the driver’s doorjamb. 5 2 3 HFC-134a (R-134a) 15.8−17.6 oz (450−500 g) SP-10 Capacities Engine coolant Engine oil Change＊1 Total Change＊2 Including filter Without filter Total Automatic Change transmission Total fluid Windshield U.S. Models washer Canada Models reservoir 1.
Specifications (6-cylinder Models) Battery Capacity Fuses Interior Lights Headlights 12 V − 55 AH/5 HR 12 V − 72 AH/20 HR Driver’s side Passenger’s side Under-hood Engine Type Bore x Stroke Displacement Compression ratio Spark plugs See page 480 or the fuse label attached on the side panel. See page 481 or the fuse label attached to the inside of the fuse box door. See page 479 or the fuse box cover. Water cooled 4-stroke, SOHC VTEC 6-cylinder (V6), gasoline engine 3.50 x 3.66 in (89.0 x 93.
Specifications (6-cylinder Models) Alignment Toe-in Camber Caster Tires Size Pressure Front Rear Front Rear Front Front/Rear Spare Front/Rear Spare 0.00 in (0.0 mm) 0.08 in (2.0 mm) −0°03’ −1°12’ 3°52’ P235/45R18 94V T135/80D16 101M 33 psi (230 kPa , 2.3 kgf/cm ) 60 psi (420 kPa , 4.
DOT Tire Quality Grading (U.S. Vehicles) The tires on your vehicle meet all U.S. Federal Safety Requirements. All tires are also graded for treadwear, traction, and temperature performance according to Department of Transportation (DOT) standards. The following explains these gradings. Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
DOT Tire Quality Grading (U.S. Vehicles) Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
Tire Labeling The tires that came on your vehicle have a number of markings. Those you should be aware of are described below. TIRE LABELING EXAMPLE R 18 − Rim diameter in inches. (1) P235/45R18 94V P − Vehicle type (P indicates passenger vehicle). 235 − Tire width in millimeters. 45 − Aspect ratio (the tire’s section height as a percentage of its width). (1) (3) (4) − Tire construction code (R indicates radial).
Tire Labeling Tire Identification Number (TIN) The tire identification number (TIN) is a group of numbers and letters that look like the following example. TIN is located on the sidewall of the tire. DOT B97R FW6X 2202 DOT −This indicates that the tire meets all requirements of the U.S. Department of Transportation. B97R −Manufacturer’s identification mark. Load Rating − Means the maximum load that a tire is rated to carry for a given inflation pressure.
Tire Pressure Monitoring System (TPMS) − Required Federal Explanation Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label.
Tire Pressure Monitoring System (TPMS) − Required Federal Explanation Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists.
Emissions Controls The burning of gasoline in your vehicle’s engine produces several byproducts. Some of these are carbon monoxide (CO), oxides of nitrogen (NOx), and hydrocarbons (HC). Gasoline evaporating from the tank also produces hydrocarbons. Controlling the production of NOx, CO, and HC is important to the environment. Under certain conditions of sunlight and climate, NOx and HC react to form photochemical ‘‘smog.’’ Carbon monoxide does not contribute to smog creation, but it is a poisonous gas.
Emissions Controls Exhaust Emissions Controls The exhaust emissions controls include three or four systems: PGM-FI, ignition timing control, exhaust gas recirculation (6-cylinder models), and three way catalytic converter. These systems work together to control the engine’s combustion and minimize the amount of HC, CO, and NOx that come out the tailpipe. The exhaust emissions control systems are separate from the crankcase and evaporative emissions control systems.
Three Way Catalytic Converter The three way catalytic converter contains precious metals that serve as catalysts, promoting chemical reactions to convert the exhaust gasses without affecting the metals. The catalytic converter is referred to as a three-way catalyst, since it acts on HC, CO, and NOx. A replacement unit must be an original Acura part or its equivalent. The three way catalytic converter must operate at a high temperature for the chemical reactions to take place.
Emissions Testing Testing of Readiness Codes If you take your vehicle for an emissions test shortly after the battery has been disconnected or gone dead, it may not pass the test. This is because of certain ‘‘readiness codes’’ that must be set in the onboard diagnostics for the emissions systems. These codes are erased when the battery is disconnected, and set again only after several days of driving under a variety of conditions.
Emissions Testing 7. Select a nearby lightly traveled major highway where you can maintain a speed of 50 to 60 mph (80 to 97 km/h) for at least 20 minutes. Drive on the highway in D (automatic) or 5th (manual). Do not use the cruise control. When traffic allows, drive for 90 seconds without moving the accelerator pedal. (Vehicle speed may vary slightly; this is okay.
Warranty and Client Relations Client Service Information ........... 506 Warranty Coverages ..................... 507 Reporting Safety Defects (U.S. Vehicles) ........................... 508 Authorized Manuals ......................
Client Service Information Acura dealership personnel are trained professionals. They should be able to answer all your questions. If you encounter a problem that your dealership does not solve to your satisfaction, please discuss it with the dealership’s management. The service manager or general manager can help. Almost all problems are solved in this way. If you are dissatisfied with the decision made by the dealership’s management, contact Acura Client Services.
Warranty Coverages U.S. Owners Your new vehicle is covered by these warranties: Emissions Control Systems Defects Warranty and Emissions Performance Warranty − these two warranties cover your vehicle’s emissions control systems. Time, mileage, and coverage are conditional. Please read your warranty booklet for exact information. Original Equipment Battery Limited Warranty − this warranty gives up to 100% credit toward a replacement battery.
Reporting Safety Defects (U.S. Vehicles) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA), in addition to notifying American Honda Motor Co., Inc. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Authorized Manuals Purchasing Factory Authorized Manuals (U.S. only) The publications shown below can be purchased from Helm Incorporated. You can order by phone or online: Call Helm Inc. at 1-800-782-4356 (credit card orders only) Go online at www. helminc. com If you are interested in other years or models, contact Helm Inc. at 1-800-782-4356.
Index A B Battery Charging System Indicator............................ 61, 471 Jump Starting ............................. 466 Maintenance ............................... 453 Specifications ..................... 489, 492 Before Driving ............................... 345 Belts, Seat ..................................... 8, 19 Beverage Holders .......................... 155 Bluetooth Audio .................... 217, 279 Bluetooth HandsFreeLink ......... 304 Booster Seats ...................................
Index C Capacities Chart .................... 488, 491 Carbon Monoxide Hazard .............. 55 Carrying Cargo .............................. 359 CAUTION, Explanation of .............. iii CD Care .......................................... 256 CD Changer.................................... 244 CD Player........................................ 189 Certification Label ......................... 486 Ceiling Light ................................... 161 Chains .............................................
Index Doors Auto Door Lock ................. 100, 124 Auto Door Unlock ............. 106, 124 Childproof Door Locks ............. 125 Locking and Unlocking ............. 124 DOT Tire Quality Grading ........... 494 Downshifting, Manual Transmission .............................. 370 Driver and Passenger Safety ............ 5 Driving ............................................ 365 Economy ..................................... 354 Driving Position Memory System.........................................
Index Fluids Automatic Transmission........... 423 Brake ........................................... 427 Clutch .......................................... 428 Manual Transmission ............... 426 Windshield Washer ........... 110, 423 Fog Lights ...................................... 115 Folding Rear Seats......................... 138 Four-way Flashers ......................... 117 Front Airbags ............................... 9, 25 Fuel ..................................................
Index System Message .......................... 67 TPMS .................................. 386, 389 Turn Signal and Hazard Warning .................................... 64 VSA Activation ............................. 63 VSA System .................................. 63 Indicators, Instrument Panel .......... 60 Infant Restraint ................................ 41 Infant Seats ....................................... 41 Tether Anchorage Points ........... 50 Inflation, Proper Tire ....
Index Locks Anti-theft Steering Column ...... 122 Childproof Door ......................... 125 Fuel Fill Door ............................. 347 Glove Box ................................... 157 Lockout Prevention ................... 125 Power Door ................................ 124 Trunk .......................................... 130 Low Coolant Level ......................... 353 Low Fuel Indicator .......................... 67 Lower Gear, Downshifting to a.... 370 Low Oil Pressure Indicator ....
Index Parking Lights................................ 111 Parking Over Things that Burn ... 382 Passenger Airbag Off Indicator ..... 33 PGM-FI System.............................. 501 Pollen Filter .................................... 442 Power Door Locks ......................... 124 Power Seat Adjustments ............... 134 Power Socket Locations ....... 154, 156 Power Windows ............................. 147 Pregnancy, Using Seat Belts .......... 17 Protecting Adults and Teens..........
Index Seat Belts ...................................... 8, 19 Additional Information ................ 19 Automatic Seat Belt Tensioners ................................ 21 Cleaning ...................................... 441 Lap/Shoulder Belt ................. 15, 20 Maintenance ................................. 22 Reminder Indicator and Beeper ................................. 19, 60 System Components.................... 19 Use During Pregnancy................ 17 Wearing a Lap/Shoulder Belt ....
Index Steering Wheel Adjustments ............................... 118 Anti-theft Column Lock ............ 122 Steering Wheel Buttons ................. 71, 286, 298, 304 Stereo Sound System .................... 174 Sun Visors ....................................... 159 Sunglasses Holder ......................... 158 Supplemental Restraint System................................... 9, 23 Servicing ....................................... 34 SRS Indicator.......................... 31, 62 System Components........
Index Treadwear ...................................... 448 Trip Computer ................................. 74 Trip Meter ........................................ 73 Trunk............................................... 130 Emergency Opener ................... 132 Main Switch ................................ 131 Opening....................................... 130 Open Indicator ....................... 11, 65 Opening Manually ..................... 132 Turn Signals ...................................
Service Information Summary Gasoline: 4-cylinder models Premium unleaded gasoline, pump octane number of 91 or higher recommended (see ‘‘Fuel Recommendations’’ on page 346 ). Recommended Engine Oil: API Premium grade 5W-20 detergent oil (see page 415). Oil change capacity (including filter): 4-cylinder models 6-cylinder models Premium unleaded gasoline, pump octane number of 91 or higher required (see ‘‘Fuel Recommendations’’ on page 346 ). Fuel Tank Capacity: 18.5 US gal (70 ) 4.2 US qt (4.
Owner’s Identification This owner’s manual should be considered a permanent part of the vehicle and should remain with the vehicle when it is sold. OWNER This owner’s manual covers all models of the TSX. You may find descriptions of equipment and features that are not on your particular model. ADDRESS STREET CITY STATE/PROVINCE/TERRITORY ZIP CODE/ POSTAL CODE V. I. N. DELIVERY DATE The information and specifications included in this publication were in effect at the time of approval for printing.
