Product Specifications

ManualsBrandsAdafruit Industries ManualsLithium Polymer (LiPo)LiPo Battery Cell - 3.7V 1200mAh

        

   

Specification No. 

Q/WAPL503562-1011

Edition No.           

1.0

     

Polymer Lithium-ion Battery

Product Specification

Model：503562 1200mAh

Prepared by：Sunping  

Checked by：Zhu Qi 

                       Approve by: Jin Gang

All 

 pages

Hunan Sounddon New Energy Co., Ltd

Address:No.98, Fuzhou Road,Jinhua Demonstration Area,Xiangtan City,Hunan Province,China.

E-mail:linda.ding@soundnewenergy.com

http://www.soundnewenergy.com

Tel: (86) 731 - 5856 7126

Fax: (86) 731 - 5823 6346

Summary of content (10 pages)

PAGE 1
Specification No. Q/WAPL503562-1011 Edition No. 1.0 Polymer Lithium-ion Battery Product Specification Model：503562 1200mAh Hunan Sounddon New Energy Co., Ltd Address:No.98, Fuzhou Road,Jinhua Demonstration Area,Xiangtan City,Hunan Province,China. http://www.soundnewenergy.com Tel: (86) 731 - 5856 7126 Fax: (86) 731 - 5823 6346 E-mail:linda.ding@soundnewenergy.
PAGE 2
Polymer Lithium-ion battery Doc. No. Q/WAPL503562-1011 Edition No. 1.0 2/10 Product Specification 1、 Scope This product specification describes polymer lithium-ion battery. Please using the test methods that recommend in this specification. If you have any opinions or advices about the test items and methods, please contact us. Please read the cautions recommended in the specifications first, take the credibility measure of the cell’s using.
PAGE 3
Polymer Lithium-ion battery Doc. No. Q/WAPL503562-1011 Edition No. 1.0 3/10 Product Specification Item Test Methods After 4.1 0.2C Capacity standard discharging at charging, 0.2C 5A to laying voltage Performance the battery 2.75V, 0.5h, recording then the ≥300min discharging time. After 4.2 1C Capacity standard charging, laying the battery 0.5h, then ≥54min discharging at 1C5A to voltage 2.75V, recording the discharging time. Constant current 0.5C5A charge to 4.
PAGE 4
Polymer Lithium-ion battery Doc. No. Q/WAPL-503562-1011 Edition No. 1.0 4/10 Product Specification Item 6.1 Test Methods Vibration Performance After standard charging, put battery on the vibration No influence to batteries' table. 30 min experiment from X,Y ,Z axis. Scan rate: 1 electrical performance and oct/min; Frequency 10-30Hz, Swing 0.38mm; Frequency appearance. 30-55Hz, Swing 0.19mm. After vibration test, batteries were laying on the vibration 6.2 Collision 6.
PAGE 5
Polymer Lithium-ion battery Doc. No. Q/WAPL503562-1011 Edition No. 1.0 5/10 Product Specification The batteries must be careful of proceed the operation for its soft package. 8.1.1 Aluminum packing materials The aluminum packing material was easily damaged by the sharp edge part, such as nickel-tabs.
PAGE 6
Polymer Lithium-ion battery Doc. No. Q/WAPL503562-0811 Edition No. 1.0 6/10 Product Specification Al interlayer Fig.2. Single folding edge schematic of PL cells R Fig.3. Reverse folding edge schematic of PL cells 8.1.4 Tabs ⑴ The batteries’ tabs are not so stubborn especially for aluminum tabs. Don’t bend tabs. ⑵ The tab-tapes are used to isolate The anode /cathode tabs from Aluminum packing materials to prevent short-circuit, so prohibit manicuring of the tab-tapes. 8.1.
PAGE 7
Polymer Lithium-ion battery Doc. No. Q/WAPL503562-1011 Edition No. 1.0 Product Specification 7/10 ⑶ Temperature 0～40℃ is preferred when charging; ⑷ Charging voltage must be lower than 4.25V. 8.3.2 discharge ⑴ Discharging current must be lower than (or equal to )2C5A; ⑵ Temperature 0～60℃ is preferred when discharging; ⑶ Discharging voltage must not be lower than 2.75V. 8.3.3 over-discharge It should be noted that the cell would be at an over-discharge state by its self-discharge.
PAGE 8
Polymer Lithium-ion battery Doc. No. Q/WAPL503562-1011 Edition No. 1.0 Product Specification 8/10 Battery pack should have sufficient strength and battery should be protected from mechanical shock. No sharp edge components should be inside the pack contains the battery. 9.2 PCM design The overcharge threshold voltage should not be exceeding 3.95V. The over-discharge threshold voltage should not be lower than 2.3V. The PCM should have short protection function built inside. 9.
PAGE 9
Polymer Lithium-ion battery Doc. No. Q/WAPL503562-1011 Edition No. 1.0 9/10 Product Specification Here is no insulated between Sealed edge & protect component Fig.4. Schematic of wrong assembly 10.
PAGE 10
L D black wire G L black wire red wire F D A A C C red wire B B H □Cell adding PCM, wire H □ Cell adding wire Parameter:√ Max（mm） Remak Item A Length 62.2 L Space between Tabs B Width 35.5 E PP membrane Length 2.0 H Thickness 5.