Datasheet

ManualsBrandsAdafruit ManualsAdafruitADS1115 16-Bit ADC board

ADS1113

ADS1114

ADS1115

www.ti.com

SBAS444B –MAY 2009–REVISED OCTOBER 2009

When the master has finished communicating with a byte; the I

C specification prohibits acknowledgment

slave, it may issue a STOP condition. When a STOP of the Hs master code. Upon receiving a master

condition is issued, the bus becomes idle again. The code, the ADS1113/4/5 switch on Hs mode filters,

master may also issue another START condition. and communicate at up to 3.4MHz. The ADS1113/4/5

When a START condition is issued while the bus is switch out of Hs mode with the next STOP condition.

active, it is called a repeated START condition.

For more information on high-speed mode, consult

See the Timing Requirements section for a timing the I

C specification.

diagram showing the ADS1113/4/5 I

C transaction.

SLAVE MODE OPERATIONS

C ADDRESS SELECTION

The ADS1113/4/5 can act as either slave receivers or

The ADS1113/4/5 have one address pin, ADDR, that slave transmitters. As a slave device, the

sets the I

C address. This pin can be connected to ADS1113/4/5 cannot drive the SCL line.

ground, VDD, SDA, or SCL, allowing four addresses

to be selected with one pin as shown in Table 5. The Receive Mode:

state of the address pin ADDR is sampled

In slave receive mode the first byte transmitted from

continuously.

the master to the slave is the address with the R/W

bit low. This byte allows the slave to be written to.

Table 5. ADDR Pin Connection and

The next byte transmitted by the master is the

Corresponding Slave Address

ADDR PIN SLAVE ADDRESS

acknowledge receipt of the register pointer byte. The

Ground 1001000

next two bytes are written to the address given by the

VDD 1001001

byte sent. Register bytes are sent with the most

SDA 1001010

significant byte first, followed by the least significant

SCL 1001011

byte.

C GENERAL CALL

Transmit Mode:

The ADS1113/4/5 respond to the I

C general call

In slave transmit mode, the first byte transmitted by

address (0000000) if the eighth bit is '0'. The devices

the master is the 7-bit slave address followed by the

acknowledge the general call address and respond to

high R/W bit. This byte places the slave into transmit

commands in the second byte. If the second byte is

mode and indicates that the ADS1113/4/5 are being

00000110 (06h), the ADS1113/4/5 reset the internal

read from. The next byte transmitted by the slave is

registers and enter power-down mode.

the most significant byte of the register that is

indicated by the register pointer. This byte is followed

by an acknowledgment from the master. The

C SPEED MODES

remaining least significant byte is then sent by the

The I

C bus operates at one of three speeds.

slave and is followed by an acknowledgment from the

Standard mode allows a clock frequency of up to

master. The master may terminate transmission after

100kHz; fast mode permits a clock frequency of up to

any byte by not acknowledging or issuing a START or

400kHz; and high-speed mode (also called Hs mode)

STOP condition.

allows a clock frequency of up to 3.4MHz. The

ADS1113/4/5 are fully compatible with all three

WRITING/READING THE REGISTERS

modes.

To access a specific register from the ADS1113/4/5,

No special action is required to use the ADS1113/4/5

the master must first write an appropriate value to the

in standard or fast mode, but high-speed mode must

Pointer register. The Pointer register is written directly

be activated. To activate high-speed mode, send a

after the slave address byte, low R/W bit, and a

special address byte of 00001xxx following the

successful slave acknowledgment. After the Pointer

START condition, where xxx are bits unique to the

Hs-capable master. This byte is called the Hs master

master issues a STOP or a repeated START

code. (Note that this is different from normal address

condition.

bytes; the eighth bit does not indicate read/write

status.) The ADS1113/4/5 do not acknowledge this

Product Folder Link(s): ADS1113 ADS1114 ADS1115