Datasheet

ManualsBrandsADAFRUIT ManualsDev KitsPower supply module

10 µF

6.8 µH

VBAT

VOUT

2.2 µF

220 µF

LBO

PGND

LBI

SYNC

GND

TPS6103x

e.g. 5 V up to

1000 mA

Low Battery

Comparator

Output

1.8 V to 5 V

Input

Product

Folder

Sample &

Buy

Technical

Documents

Tools &

Software

Support &

Community

TPS61030

TPS61031

TPS61032

SLUS534G –SEPTEMBER 2002–REVISED MARCH 2015

TPS6103x 96% Efficient Synchronous Boost Converter With 4A Switch

1 Features 3 Description

The TPS6103x devices provide a power supply

• 96% Efficient Synchronous Boost Converter With

solution for products powered by either a one-cell Li-

1000-mA Output Current

Ion or Li-polymer, or a two to three-cell alkaline, NiCd

From 1.8-V Input

or NiMH battery. The converter generates a stable

• Device Quiescent Current: 20-µA (Typ)

output voltage that is either adjusted by an external

resistor divider or fixed internally on the chip. It

• Input Voltage Range: 1.8-V to 5.5-V

provides high efficient power conversion and is

• Fixed and Adjustable Output Voltage Options Up

capable of delivering output currents up to 1 A at 5 V

to 5.5-V

at a supply voltage down to 1.8 V. The implemented

• Power Save Mode for Improved Efficiency at Low

boost converter is based on a fixed frequency, pulse-

Output Power

width- modulation (PWM) controller using a

synchronous rectifier to obtain maximum efficiency.

• Low Battery Comparator

At low load currents the converter enters Power Save

• Low EMI-Converter (Integrated Antiringing Switch)

mode to maintain a high efficiency over a wide load

• Load Disconnect During Shutdown

current range. The Power Save mode can be

• Over-Temperature Protection

disabled, forcing the converter to operate at a fixed

switching frequency. It can also operate synchronized

• Available in a Small 4 mm x 4 mm QFN-16 or in a

to an external clock signal that is applied to the

TSSOP-16 Package

SYNC pin. The maximum peak current in the boost

switch is limited to a value of 4500 mA.

2 Applications

The converter can be disabled to minimize battery

All Single Cell Li or Dual Cell Battery Operated

drain. During shutdown, the load is completely

Products as MP-3 Player, PDAs, and Other

disconnected from the battery. A low-EMI mode is

Portable Equipment

implemented to reduce ringing and, in effect, lower

radiated electromagnetic energy when the converter

enters the discontinuous conduction mode.

Device Information

(1)

PART NUMBER PACKAGE BODY SIZE (NOM)

TPS61030

TPS61031 TSSOP (16) 5.00 mm × 4.40 mm

TPS61032

TPS61030

TPS61031 QFN (16) 4.00 mm x 4.00 mm

TPS61032

(1) For all available packages, see the orderable addendum at

the end of the datasheet.

4 Simplified Schematic

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,

intellectual property matters and other important disclaimers. PRODUCTION DATA.

Summary of content (42 pages)

PAGE 1
Sample & Buy Product Folder Support & Community Tools & Software Technical Documents TPS61030, TPS61031, TPS61032 SLUS534G – SEPTEMBER 2002 – REVISED MARCH 2015 TPS6103x 96% Efficient Synchronous Boost Converter With 4A Switch 1 Features 3 Description • The TPS6103x devices provide a power supply solution for products powered by either a one-cell LiIon or Li-polymer, or a two to three-cell alkaline, NiCd or NiMH battery.
PAGE 2
TPS61030, TPS61031, TPS61032 SLUS534G – SEPTEMBER 2002 – REVISED MARCH 2015 www.ti.com Table of Contents 1 2 3 4 5 6 7 8 Features .................................................................. Applications ........................................................... Description ............................................................. Simplified Schematic............................................. Revision History..................................................... Device Comparison Table......
PAGE 3
TPS61030, TPS61031, TPS61032 www.ti.com SLUS534G – SEPTEMBER 2002 – REVISED MARCH 2015 6 Device Comparison Table (1) OUTPUT VOLTAGE DC/DC TA PART NUMBER (1) PACKAGE Adjustable TPS61030 3.3 V 16-Pin TSSOP PowerPAD™ TPS61031 5V -40°C to 85°C TPS61032 Adjustable TPS61030 3.3 V 16-Pin QFN TPS61031 5V (1) (1) TPS61032 Contact the factory to check availability of other fixed output voltage versions. For all available packages, see the orderable addendum at the end of the datasheet.
PAGE 4
TPS61030, TPS61031, TPS61032 SLUS534G – SEPTEMBER 2002 – REVISED MARCH 2015 www.ti.com 8 Specifications 8.1 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) (1) VI MIN MAX UNIT Input voltage on LBI –0.3 3.6 V V Input voltage on SW, VOUT, LBO, VBAT, SYNC, EN, FB –0.
PAGE 5
TPS61030, TPS61031, TPS61032 www.ti.com SLUS534G – SEPTEMBER 2002 – REVISED MARCH 2015 8.5 Electrical Characteristics over recommended free-air temperature range and over recommended input voltage range (typical at an ambient temperature range of 25°C) (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT DC/DC STAGE VI Input voltage range 1.8 5.5 VO TPS61030 output voltage range 1.8 5.
PAGE 6
TPS61030, TPS61031, TPS61032 SLUS534G – SEPTEMBER 2002 – REVISED MARCH 2015 www.ti.com 8.6 Typical Characteristics Table 1. Table Of Graphs DC/DC CONVERTER FIGURE vs Input voltage Figure 1, Figure 2 vs Output current (TPS61030) (VO = 2.5 V, VI = 1.8 V, VSYNC = 0 V) Figure 3 vs Output current (TPS61031) (VO = 3.3 V, VI = 1.8 V, 2.4 V, VSYNC = 0 V) Figure 4 vs Output current (TPS61032) (VO = 5.0 V, VI = 2.4 V, 3.
PAGE 7
TPS61030, TPS61031, TPS61032 www.ti.com SLUS534G – SEPTEMBER 2002 – REVISED MARCH 2015 100 100 90 90 80 80 70 70 Efficiency - % Efficiency - % VBAT = 1.8 V 60 50 40 VBAT = 2.4 V 60 50 40 30 30 20 20 10 10 0 0 1 10 100 1000 IO - Output Current - mA VO = 2.5 V 1 10000 10 1000 10000 VO = 3.3 V VI = 1.8 V Figure 3. TPS61030 Efficiency vs Output Current Figure 4. TPS61031 Efficiency vs Output Current 100 100 IO = 100 mA 90 VBAT = 2.4 V 80 IO = 1000 mA 90 VBAT = 3.
PAGE 8
TPS61030, TPS61031, TPS61032 SLUS534G – SEPTEMBER 2002 – REVISED MARCH 2015 www.ti.com 16 5.15 14 No-Load Supply Current Into VBAT - µA 5.2 VO - Output Voltage - V 5.1 5.05 5 4.95 4.9 4.85 1 10 100 1000 IO - Output Current - mA 25°C 12 –40°C 10 8 6 4 2 0 4.8 85°C 10000 2 3 4 5 VI - Input Voltage - V VBAT = 3.3 V Figure 10. TPS61032 No-Load Supply Current into Vbat vs input Voltage Figure 9.
PAGE 9
TPS61030, TPS61031, TPS61032 www.ti.com SLUS534G – SEPTEMBER 2002 – REVISED MARCH 2015 10 Detailed Description 10.1 Overview The TPS6103x synchronous step-up converter typically operates at a 600 kHz frequency pulse width modulation (PWM) at moderate to heavy load currents. The converter enters Power Save mode at low load currents to maintain a high efficiency over a wide load. The Power Save mode can also be disabled, forcing the converter to operate at a fixed switching frequency.
PAGE 10
TPS61030, TPS61031, TPS61032 SLUS534G – SEPTEMBER 2002 – REVISED MARCH 2015 www.ti.com 10.3 Feature Description 10.3.1 Controller Circuit The controller circuit of the device is based on a fixed frequency multiple feedforward controller topology. Input voltage, output voltage, and voltage drop on the NMOS switch are monitored and forwarded to the regulator.
PAGE 11
TPS61030, TPS61031, TPS61032 www.ti.com SLUS534G – SEPTEMBER 2002 – REVISED MARCH 2015 Device Functional Modes (continued) 10.4.3 Power Save Mode And Synchronization The SYNC pin can be used to select different operation modes. To enable power save, SYNC must be set low. Power save mode is used to improve efficiency at light load. In power save mode the converter only operates when the output voltage trips below a set threshold voltage.
PAGE 12
TPS61030, TPS61031, TPS61032 SLUS534G – SEPTEMBER 2002 – REVISED MARCH 2015 www.ti.com 11 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 11.
PAGE 13
TPS61030, TPS61031, TPS61032 www.ti.com SLUS534G – SEPTEMBER 2002 – REVISED MARCH 2015 11.2.2 Detailed Design Procedure 11.2.2.1 Programming The Output Voltage The output voltage of the TPS61030 dc/dc converter section can be adjusted with an external resistor divider. The typical value of the voltage on the FB pin is 500 mV. The maximum allowed value for the output voltage is 5.5 V. The current through the resistive divider should be about 100 times greater than the current into the FB pin.
PAGE 14
TPS61030, TPS61031, TPS61032 SLUS534G – SEPTEMBER 2002 – REVISED MARCH 2015 V L+ BAT DI www.ti.com ǒVOUT–VBATǓ L ƒ V OUT (5) Parameter f is the switching frequency and ΔIL is the ripple current in the inductor, i.e., 10% × IL. In this example, the desired inductor has the value of 5.5 µH. In typical applications a 6.8 µH inductance is recommended. The minimum possible inductance value is 2.2 µH. With the calculated inductance and current values, it is possible to choose a suitable inductor.
PAGE 15
TPS61030, TPS61031, TPS61032 www.ti.com SLUS534G – SEPTEMBER 2002 – REVISED MARCH 2015 11.2.2.4.2.1 Small Signal Stability When using output capacitors with lower ESR, like ceramics, it is recommended to use the adjustable voltage version. The missing ESR can be easily compensated there in the feedback divider. Typically a capacitor in the range of 10 pF in parallel to R3 helps to obtain small signal stability with lowest ESR output capacitors.
PAGE 16
TPS61030, TPS61031, TPS61032 SLUS534G – SEPTEMBER 2002 – REVISED MARCH 2015 www.ti.com Enable 5 V/Div, DC Output Voltage 2 V/Div, DC Input Current 500 mA/Div, DC Voltage at SW 2 V/Div, DC Timebase - 400 ms/Div RL = 20 Ω VI = 2.4 V Figure 18. TPS61030 DC/DC Converter Start-Up After Enable 11.2.4 System Examples 11.2.4.1 Power Supply Solution For Maximum Output Power Second application example L1 SW 6.8 µH Battery Input VOUT C2 2.
PAGE 17
TPS61030, TPS61031, TPS61032 www.ti.com SLUS534G – SEPTEMBER 2002 – REVISED MARCH 2015 11.2.4.2 Power Supply Solution With Auxiliary Positive Output Voltage Third application example C5 VCC2 10 V Unregulated Auxiliary Output DS1 C6 1 µF 0.1 µF L1 6.8 µH SW C2 2.
PAGE 18
TPS61030, TPS61031, TPS61032 SLUS534G – SEPTEMBER 2002 – REVISED MARCH 2015 www.ti.com 12 Power Supply Recommendations The device is designed to operate from an input voltage supply range between 1.8 V and 5.5 V. This input supply must be well regulated. If the input supply is located more than a few inches from the converter, additional bulk capacitance may be required in addition to the ceramic bypass capacitors. An electrolytic or tantalum capacitor with a value of 47 μF is a typical choice.
PAGE 19
TPS61030, TPS61031, TPS61032 www.ti.com SLUS534G – SEPTEMBER 2002 – REVISED MARCH 2015 Thermal Considerations (continued) Three basic approaches for enhancing thermal performance are listed below: • Improving the power dissipation capability of the PCB design • Improving the thermal coupling of the component to the PCB • Introducing airflow in the system The maximum junction temperature (TJ) of the TPS6103x devices is 125°C. The thermal resistance of the 16-pin TSSOP PowerPAD package (PWP) is RΘJA = 36.
PAGE 20
PACKAGE OPTION ADDENDUM www.ti.
PAGE 21
PACKAGE OPTION ADDENDUM www.ti.com 10-Mar-2015 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production.
PAGE 22
PACKAGE MATERIALS INFORMATION www.ti.com 10-Mar-2015 TAPE AND REEL INFORMATION *All dimensions are nominal Device TPS61030PWPR Package Package Pins Type Drawing SPQ HTSSOP Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant PWP 16 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 TPS61030RSAR QFN RSA 16 3000 330.0 12.4 4.3 4.3 1.5 8.0 12.0 Q2 TPS61031PWPR HTSSOP PWP 16 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.
PAGE 23
PACKAGE MATERIALS INFORMATION www.ti.com 10-Mar-2015 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS61030PWPR HTSSOP PWP 16 2000 367.0 367.0 35.0 TPS61030RSAR QFN RSA 16 3000 338.1 338.1 20.6 TPS61031PWPR HTSSOP PWP 16 2000 367.0 367.0 35.0 TPS61031RSAR QFN RSA 16 3000 338.1 338.1 20.6 TPS61032PWPR HTSSOP PWP 16 2000 367.0 367.0 35.0 TPS61032RSAR QFN RSA 16 3000 338.1 338.1 20.
PAGE 24
PAGE 25
PAGE 26
PAGE 27
PAGE 28
PAGE 29
PAGE 30
PAGE 31
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
PAGE 32
Adafruit Powerboost 1000 Basic Created by lady ada Last updated on 2014-07-30 06:30:12 PM EDT
PAGE 33
Guide Contents Guide Contents 2 Overview 3 Pinouts 7 Power Pins 8 Control Pins 8 (http://adafru.it/dLZ)LEDs 9 Battery and USB connection 9 Downloads 10 Datasheets 10 Schematics 10 PCB Print 10 © Adafruit Industries https://learn.adafruit.
PAGE 34
Overview PowerBoost is the perfect power supply for your power-hungry portable project! This little DC/DC boost converter module can run from 1.8V batteries or higher, and convert that voltage to 5.2V DC for running your 5V projects. With a beefy 4A DC/DC converter, it can give you 1A+ from as low as 2V. Like our popular 5V 1A USB wall adapter (http://adafru.it/duP), we tweaked the output to be 5.2V instead of a straight-up 5.
PAGE 35
The PowerBoost 1000 has at the heart a TPS61030 boost converter from TI (http://adafru.it/dLY). This boost converter chip has some really nice extras such as low battery detection, 4A internal switch, synchronous conversion, excellent efficiency, and 700KHz high-frequency operation. Check out these specs! Synchronous operation means you can disconnect the output completely by connecting the ENable pin to ground.
PAGE 36
disabled (power and low batt LED are off) Great for powering your robot, Arduino project, single-board-computer such as Raspberry Pi or BeagleBone! Each order comes with one fully assembled and tested PCB, a loose 2-PH JST jack, a 2-pin Terminal block and a loose USB A jack. © Adafruit Industries https://learn.adafruit.
PAGE 37
If you are powering your project from USB, solder the USB A jack in (a 3-minute soldering task). Then choose either JST for input (JST is often used for our LiIon batteries, but the connector is only rated for 2A) or a terminal block. If you would like to use another terminal block for output, pick up a 3.5mm 2pin block here (http://adafru.it/duR) and solder to the output spot where the USB jack would go.
PAGE 38
Pinouts For many people, the PowerBoost can be used with just the power input and power outputs. However, we have a couple handy breakouts so lets get started! © Adafruit Industries https://learn.adafruit.
PAGE 39
Power Pins There's two power 'ports' - an input (called BAT) and an output (called 5V) BAT - this is the battery input, it can range from 1.8V to 5V. Higher voltages will let you draw more current and in general, are more efficient. Try to keep the wires going to this pin nice and short - 1.5" or less is best! GND - this is the power ground. This boost converter is not 'isolated' - the ground input is the same as the ground output 5V - this is the boosted output.
PAGE 40
booster, connect this pin to ground. The switch can be as small as you like, it is just a signal. Contrast this to an inline power switch which would have to be able to handle up to 4A of current! When the chip is disabled the output is completely disconnected from the input. LBO - not a leveraged buy out! this is the Lo w Battery Output. By default it is pulled high to BAT but when the charger detects a low voltage (under 3.2V) the pin will drop down to 0V.
PAGE 41
Downloads Datasheets TPS61030 datasheet (http://adafru.it/dM0)(the DC/DC boost control chip used) Schematics PCB Print Dimensions in Inches © Adafruit Industries https://learn.adafruit.