Adam Equipment PTS SERIES With AE402 Indicator (P.N.
Adam Equipment 2010 ©
Thank you for purchasing the ADAM PTS 2000. For your safety and correct operation, please read the following instructions carefully before using it. 1.0 2.0 3.0 4.0 5.0 CONTENT INSTRUCTION ..............................................................................................................5 1.1 SPECIFICATION........................................................................................................5 1.2 PACKING LIST....................................................................
SAFETY • To prevent damage to the scale, please read these operating instructions thoroughly. • When using the pallet truck, please keep the handle in the DRIVE position. • This pallet truck must be operated by trained personnel only.
1.0 INSTRUCTION 1.1 SPECIFICATION Common specifications Model PTS 2000 Load cell Capacity 2000 kg Resolution 0.5 kg Fork length 1150mm Fork Width (each) 160mm Fork Width (total) 550mm Fork Height 80mm increasing to 195mm Net Weight 110k See the User Manual for the Indicator supplied with the PTS for more information about the weighing features and operation. 1.2 PACKING LIST Part No.
Adam Equipment 2010 ©
2.0 INSTALLATION Please follow the installation instructions to ensure correct operation of your PTS. In transportation the handle is removed from the truck, this needs to be installed following the instructions below: 1) Insert the roller pin into the hole of roller rack, securing the handle to the frame. 2) Fit the split pin through the holes provided. 3) Pass the chain through the center hole of the roller pin. Secure the end of the chain to the slot on the end of the unloading plate.
Adam Equipment 2010 ©
2.
The Indicator bracket is fitted to the PTS using 4 x M4 screws as the picture below shows, these should be tightened using the Allen Key supplied . M4 x 6 Screws 4 places The Indicator cable goes through the hole on the bracket and connects to the Indicator using the 7 pin connector. 7 pin connector fitted here.
The AE 402 indicator is placed into the mounting bracket, and secured using the two plastic fasteners as shown below: Plastic fasteners used to secure Indicator to the bracket.
2.2 GK INDICATOR ASSEMBLY (USA ONLY) The GK mounting plate is fitted into the runners on the bottom of the GK GK mounting plate The display cable is fitted into the GK and the fixing screws are tightened. Connect cable to indicator, secure mounting screws Using the Allen key attached inside the packing box, secure the GK indicator to the bracket using the 4 x M4 screws.
The 5 pin end of display cable is fitted into the 5 pin connector on the truck and the locking ring is tightened. The bracket should then be fitted to the truck and the 4 x M4 screws tightened by an Allen key M4 x 6 screws 4 places 3.0 CALIBRATION The PTS is factory calibrated, please refer to the user manual for indicator supplied (AE 402 or GK) when further calibration when required.
4.0 No. TROUBLEINGSHOOTING Problem Cause Solution Forks cannot ascend to 1 the maximum height Inadequate hydraulic oil. Refill oil chamber. No hydraulic oil. Refill oil chamber Dirty oil. 2 Forks can not be raised Fork bolts too close or screws too tight so that the valve remains open. There is air in the hydraulic oil. 3 Forks can not descend 4 Oil spillage Forks descend when 5 the trigger is not in descend position 5.0 Change oil Adjust bolts or screws Vent the air.
Manufacturer’s Declaration of Conformity This product has been manufactured in accordance with the harmonised European standards, following the provisions of the below stated directives: Electro Magnetic Compatibility Directive 2004/108/EC Low Voltage Directive 2006/95/EC Adam Equipment Co. Ltd. Bond Avenue, Denbigh East Milton Keynes, MK1 1SW United Kingdom FCC COMPLIANCE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
ADAM EQUIPMENT is an ISO 9001:2008 certified global organisation with more than 30 years experience in the production and sale of electronic weighing equipment. Products are sold through a world wide distributor network supported from our company locations in the UK, USA, SOUTH AFRICA and AUSTRALIA. ADAM’s products are predominantly designed for the Laboratory, Educational, Medical and Industrial Segments.
