Installation Instructions

ManualsBrandsadapt ManualsCabinet Organization & Accessoriesadapt.™ 12" Soft-Close Chrome Rollout Basket

Face-Frame Frameless

May be installed in a face-frame or frameless

cabinet, with the sizes as shown in the chart.

**Side mount requires the included adapter blocks

Model

“A” “B”

Opening Cabinet

Side

Mount

Bottom

Mount

12”

12” 15”

over

12”

over

15”

Yes

15”

15” 18”

over

15”

over

18”

Yes

21”

21” 24”

over

21”

over

24”

Yes

Depth

Minimum

22-

/16”

22-

/16”

22-

/16”

Depth

“B”

“A”

ITEM

QTY

1 Left, 1 Right

PART NUMBER

SS-20.1081 (LH), SS-20.1082 (RH)

SS-10.1028

SS-10.1029

SS-10.1030

SS-10.1031

SS-10.1032

SS-10.1033

SS-10.1034

REQUIRED TOOLS (not included)

Drill

/16” Drill bit

Phillips Screwdriver

Tape Measure

Level

Pencil

NOTE: Item #5 is small and

packed with Item #4

DESCRIPTION

Basket

Slides

Plastic Bracket

Slide Screw

Rack Screw

Hex Nut

Phillips Screw

Euro Screw

Adapter Block

▪ READ ALL INSTRUCTIONS AND CHECK PARTS BEFORE STARTING INSTALLATION

▪ RETAIN ALL PACKING MATERIALS UNTIL INSTALLATION IS COMPLETE

IMPORTANT

PARTS LIST

5 6 7 8 9

3 42

DO NOT RETURN TO THE RETAILER

If you have any questions, please contact Customer Care at

1-800-721-4191

Monday – Friday 8-5 Central Time

4814101 - MEN0624 12” Soft Close Rollout

4814102 - MEN0625 15” Soft Close Rollout

4814103 - MEN0626 21” Soft Close Rollout

Summary of content (8 pages)

PAGE 1
4814101 - MEN0624 12” Soft Close Rollout 4814102 - MEN0625 15” Soft Close Rollout 4814103 - MEN0626 21” Soft Close Rollout DO NOT RETURN TO THE RETAILER If you have any questions, please contact Customer Care at 1-800-721-4191 Monday – Friday 8-5 Central Time PARTS LIST 1 2 5 3 6 4 7 8 9 NOTE: Item #5 is small and packed with Item #4 ITEM DESCRIPTION 1 Basket QTY PART NUMBER 1 - REQUIRED TOOLS (not included) Drill 2 Slides 3 Plastic Bracket 2 SS-10.
PAGE 2
Bottom Mount - START HERE STEP A1 Screw the Basket to a left and right Slide using (4) Rack Screws. STEP A2 Place a Plastic Bracket on each Slide and place the assembly in the cabinet. NOTE: For a face-frame cabinet, make sure the Slides are located as to not strike the face-frame during operation. STEP A3 Using a pencil, mark two mounting holes in the front brackets of the Slides. Also mark the two holes in each Plastic Bracket. Remove the assembly from the cabinet.
PAGE 3
STEP A4 Drill 1/16” pilot holes in the marked locations. STEP A5 Attach the Plastic Brackets to the cabinet back wall using four Slide Screws. STEP A6 Insert the Slides into the Plastic Brackets and attach the assembly to the cabinet bottom using four Slide Screws. NOTE: If the Slides are not installed parallel, they may bind or be difficult to move during operation. Remove the Rack and check the operation of each Slide.
PAGE 4
Side Mount (w/o Adapter Block) - START HERE STEP B1 Hold the left Slide against the inside of the cabinet face frame at desired height. Make a pencil mark at the top of the front bracket on the Slide. Use a tape measure and record the height from the bottom of the cabinet to this mark. NOTE: Take into consideration the sizes of items that will be placed in the Basket and additional Baskets or any other organizational products that may be installed.
PAGE 5
HO RIZ VERTICAL LINE ON TA LL VERTICAL LINE Step B5 Remove the Slide and hold the Plastic Bracket on the cabinet back wall making sure to line up the top of Plastic Bracket with the horizontal line made in Step B1 and the center of Plastic Bracket holes placed on the vertical line. Mark the location of the two holes in the Plastic Bracket. INE HO RIZ ON TA LL INE Step B6 Drill 1/16” pilot holes in the cabinet back wall and install the Plastic Bracket using (2) Slide Screws.
PAGE 6
Side Mount with Adapter Block - START HERE STEP C1 Prepare the Adapter Kit for use by inserting two Hex Nuts into the hex slots on one Adapter Block and threading a Phillips Screw into each Hex Nut. Repeat for the second Adapter Block. DO NOT fully tighten the Phillips Screws. Step C2 Hold the left Slide against the inside of the cabinet at the desired height. Locate the pre-drilled cabinet holes that are closest, vertically, to the center of the bracket on the Slide.
PAGE 7
Step C5 Temporarily install the left Slide onto the left Adapter Block using two Phillips Screws. Make sure to hold the Slide Level. Use a tape measure and record the height from the bottom of the cabinet to the top of the bracket on the front of the Slide. While holding the left Slide level and parallel to the inside wall, measure from the inside wall to the center of the front hole in the top of the Slide. LEVEL LEVEL Step C6 Remove the left Slide from the Adapter Block by removing the Phillips Screws.
PAGE 8
HO RIZ ON TA LL VERTICAL LINE INE VERTICAL LINE Step C7 Hold the left Plastic Bracket on the cabinet back wall making sure to line up the top of Plastic Bracket with the horizontal line made in Step C6 and the center of Plastic Bracket holes placed on the vertical line. Mark the location of the two holes in the Plastic Bracket. Repeat this step for the right Plastic Bracket.