Installation guide
Table Of Contents
- Command Line Interface
- Reference Guide
- Introduction
- General Control Commands
- container Commands
- container add_level
- container create mirror
- container create mmirror
- container create mstripe
- container create mvolume
- container create raid5
- container create stripe
- container create volume
- container delete
- container extend file_system
- container extend mvolume
- container extend volume
- container list
- container lock
- container move
- container promote
- container readonly
- container readwrite
- container reconfigure
- container release_cache
- container remove drive_letter
- container remove failover
- container remove file_system
- container remove global_failover
- container restore RAID5
- container scrub
- container set cache
- container set failover
- container set global_failover
- container set io_delay
- container set label
- container show cache
- container show failover
- container split
- container unlock
- container unmirror
- controller Commands
- controller details
- controller firmware compare
- controller firmware save
- controller firmware update
- controller list
- controller pause_io
- controller rescan
- controller reset_scsi_channel
- controller resume_io
- controller set automatic_failover
- controller set array_verify
- controller show automatic_failover
- controller show channels
- controller show array_verify
- disk Commands
- diagnostic Commands
- diagnostic clear boot_parameters
- diagnostic dump structures
- diagnostic dump text
- diagnostic load_arrays
- diagnostic moderation set count
- diagnostic moderation set timer
- diagnostic moderation show count
- diagnostic moderation show timer
- diagnostic set boot_parameter
- diagnostic show boot_parameter
- diagnostic show history
- logfile Commands
- task Commands
- enclosure Commands
- enclosure activate slot
- enclosure identify slot
- enclosure list
- enclosure prepare slot
- enclosure set alarm
- enclosure set door
- enclosure set fan
- enclosure set interval
- enclosure set power
- enclosure set scsiid
- enclosure set temperature
- enclosure show fan
- enclosure show power
- enclosure show slot
- enclosure show status
- enclosure show temperature
- Automated Scripts
- Reference Guide
9-37
enclosure Commands
Examples
The following example displays status information for enclosure
management devices 0 and 1:
AAC0>enclosure show status
Executing: enclosure show status
Enclosure UpTime D:H:M PowerCycle Interval Door Alarm
--------- -------------- ---------- -------- -------- -------
0 0:04:25 2 20 UNLOCKED OFF
Enclosure Fan Status
--------- --- -------------
0 0 OK
Enclosure Power State Status
--------- ----- ------------ -------
0 0 UNKNOWN UNKNOWN
Enclosure Slot scsiId Insert Status
--------- ---- ------ ------- ----------------------------------------
--
0 0 0:00:0 0 OK UNCONFIG ACTIVATE
0 1 0:01:0 0 OK UNCONFIG ACTIVATE
0 2 0:10:0 0 OK UNCONFIG ACTIVATE
0 3 0:03:0 0 OK UNCONFIG ACTIVATE
0 4 0:04:0 0 OK UNCONFIG ACTIVATE
Enclosure Sensor Temperature Threshold Status
--------- ------ ----------- --------- --------
0 0 72 F 120 NORMAL
Enclosure UpTime D:H:M PowerCycle Interval Door Alarm
--------- -------------- ---------- -------- -------- -------
1 2:20:25 3 20 UNLOCKED OFF
Enclosure Fan Status
--------- --- -------------
1 0 NOT INSTALLED
Enclosure Power State Status
--------- ----- ------------ -------
1 0 UNKNOWN UNKNOWN
Enclosure Slot scsiId Insert Status
--------- ---- ------ ------- ----------------------------------------
--
1 0 1:00:0 0 UNCONFIG
1 1 1:01:0 0 UNCONFIG
1 2 1:10:0 0 UNCONFIG
1 3 1:03:0 0 UNCONFIG
1 4 1:04:0 0 UNCONFIG
Enclosure Sensor Temperature Threshold Status
--------- ------ ----------- --------- --------
1 0 75 F 120 NORMAL