MOTORCYCLE LASER JAMMER SYSTEM MANUAL
TABLE OF CONTENTS Introduction. . .. . . . .. . . . .. . . . .. . . . .. . . . .. . . . .. . . . .. . . . .. . . . . . . . . . . 4 Safety Warning. . . . . . .. . . . .. . . . .. . . . .. . . . .. . . . .. . . . .. . . . .. . . . . . . . . 5 Package Contents. . . . . . .. . . . .. . . . .. . . . .. . . . .. . . . .. . . . .. . . . .. . . . . . 6 Product Overview . . . . . . .. . . . .. . . . .. . . . .. . . . .. . . . .. . . . .. . . . .. . . . . . 7 Using the TPX™ Motorcycle Laser System. . .. . . . .. . .
INTRODUCTION SAFETY WARNING Dear TPX™ Motorcycle Laser Jammer System Owner, When using the TPX™ Laser Jammer System and its associated components, it is the sole responsibility of the operator to install all components properly and to ensure that they will not interfere with safe operation of the vehicle, nor will they cause any personal injury or damage in the event of an accident. The operator should operate the vehicle in a safe manner while using the system and its components.
PACKAGE CONTENTS • TPX™ Laser Jammer Transponder (1) • TPX™ Laser Jammer Interface Box (1) • TPX™ Laser Jammer Control Switch (1) • TPX™ Visual Alert (1) • TPX™ Visual Alert Mounting Tape (1) • TPX™ Laser Jammer Hinge Bracket (2) • • M4 x 12mm Screw (4) 8-18 x 5/8 Self Drilling Screw (2) • #8 Lock Washer (2) • Spirit Level (1) • Hole Plug (2) • Small Cable Tie (8) PRODUCT OVERVIEW The TPX™ Laser Jammer System is designed specifically for motorcycle use.
USING THE TPX™ MOTORCYCLE LASER JAMMER SYSTEM INSTALLATION Warning: Installation of the TPX™ Motorcycle Laser Jammer System should be performed by a qualified technician. Improper installation may interfere with the safety and proper operation of the product and/or vehicle. MOUNTING THE TRANSPONDER The TPX™ Laser Jammer System includes one Transponder for mounting on the front of the bike. An additional Transponder for rear protection is available separately.
Alternatively, the Transponder can be mounted with the Hinge Bracket tabs facing outwards as shown in Figure 4. • Remove the other liner of the Visual Alert Mounting Tape and apply the Visual Alert to the chosen mounting surface on the motorcycle using firm pressure. • Allow mounted assembly to sit overnight while tape increases bond strength. Option 2: Using Cable Ties • Determine an appropriate location for mounting the Visual Alert. • Fasten with Large Cable Ties as shown in Figure 5.
MOUNTING THE CONTROL SWITCH • Determine an appropriate location for mounting the Control Switch. The best location is one that is easily accessible while riding. • Clean the chosen mounting surface on the motorcycle with mild soap and water. Rinse with water to remove all traces of soap. • WIRING THE TPX™ LASER JAMMER SYSTEM General Refer to Figure 6 for wiring diagram. Secure all loose wires with included cable ties. Leave caps on all connectors when not in use.
Power To provide power to the system, connect the red (+) terminal cable to a 12V, 14Ga-18Ga switched power wire with the included T-Tap. Connect the black (Ground) cable to a ground. Transponder Connect the Transponder to either one of the connectors labeled “Jammer”.
OPERATION Power Press and hold the button for two seconds to turn the system on. On startup, the Visual Alert will flash three times and the audio (if installed) will beep three times. Either the or indicator will be illuminated when the system is on. Press and release the button to turn the system off. Brightness and Volume Control Press and hold the button for two seconds to toggle between Brightness Mode and Volume Mode. In Brightness Mode, the indicator will be illuminated.
Updates and Settings Firmware updates and setting changes can be performed with the included USB Cable and a computer connected to the internet. It is important to disconnect all power from the system before plugging into the computer. Go to www.AdaptivTech.com for software downloads and detailed instructions. Warning: Disconnect all power from the TPX™ Laser Jammer System before connecting to a computer.
WARRANTY WARRANTY SERVICE Adaptiv Technologies, LLC warrants to the original purchaser that the TPX™ Laser Jammer System will be free of defects in workmanship and materials for a period of one year from the date of first consumer purchase. The TPX™ Laser Jammer System consists of the Interface Box, the Transponder, the Visual Alert, the Control Switch, and the respective parts of each.
NON-WARRANTY SERVICE ACCESSORIES For all non-warranty service, follow the same procedure described in the Warranty Service section and include a nonrefundable payment of $75 for basic diagnostics and repair. Do not send cash. If there are any additional charges, we will notify you before performing the repair. The following accessories and replacement parts are available for purchase. SPECIFICATIONS Transmitter type: 8 special IR LEDs Wavelength: For more information, go to: www.AdaptivTech.
Adaptiv Technologies, LLC www.AdaptivTech.
