Instruction Manual

ManualsBrandsAdaptive Technologies ManualsAudio accessoriesPM-24-6UP-G

PoleStar™ PM-24-6UP-G

6” & Up Pole Mount with 24” long Arm

Installation Instructions

The PoleStar™ PM-24-6UP-G all-weather, galvanized steel pole

mount is designed to mount loudspeakers and other equipment

from vertical surfaces and columns. The PoleStar™ PM-24-6UP-G

accommodates many standard mounts for a wide variety of

mounting solutions, including, yokes, U-Brackets and the

PoleStar™ dual Adapter for mounting and aiming three

loudspeakers.

The universal strap kit provides a banding system to attach the PM-

24-6UP-G Pole Mount to vertical poles or columns from 6” diameter

and up.

Important: Mounting overhead system requires professional

experience. Improperly installed equipment can result in

property damage, personal injury, death and/or liability to the

installing contractor. Do not install if in doubt about the integrity of

the mounting structure.

Caution: Due to the wide variety of mounting structures,

environments, materials and mounting methods, the installing

contractor must exercise good judgment in selecting the proper

mounting area and hardware.

Follow these instructions for the most efficient and safest

mounting results.

Do not exceed the working load limit of 300lbs/136 kg.

DO NOT use Pneumatic tool to tighten bolts.

Use Loctite to permanently secure nuts to bolts and prevent

loosening overtime.

Bolt Torque: 35-40 foot pounds

Package Contents:

1 pc. Pole Mount, 6” & Up w/ 24” arm 1 pc Friction gasket

1 pc ½-13 x 3.5 hex bolt

1 pc ½-13 x 4.5 hex bolt

1 pc ½-13 nylock nut

1 pc ½ split lock washer

1 pc ½ Flat washer

2 pcs 90” long banding strap

2 pcs Retaining bolt & block assy.

2 pcs Flat washer, 3/8 SAE

1 pc Loctite #262

1 pc Instruction sheet

Install Banding Strap Kit:

Step 1: Assemble Fixed Retainer Block from the Band Kit

Mark the strap at least 4-6 inches from the end and fold the strap at the mark. Strike the strap at the bend to create a sharp radius. Slide the strap

through the Fixed Retainer Block so that its bend will pass over the beveled end of the Block. (Figure 1)

Summary of content (4 pages)

PAGE 1
PoleStar™ PM-24-6UP-G 6” & Up Pole Mount with 24” long Arm Installation Instructions The PoleStar™ PM-24-6UP-G all-weather, galvanized steel pole mount is designed to mount loudspeakers and other equipment from vertical surfaces and columns. The PoleStar™ PM-24-6UP-G accommodates many standard mounts for a wide variety of mounting solutions, including, yokes, U-Brackets and the PoleStar™ dual Adapter for mounting and aiming three loudspeakers.
PAGE 2
Step 2: Assemble the PM-24-6UP-G to the strap Insert the free end of the strap through the slots on the side of the pole mount channel, then through the Sliding Retainer Block, non-beveled end first (Figure 2). Figure 1 Step 3: Determine Strap length for Pole Holding the Fixed Block firmly against the pole, overlap the strap. Move the Sliding Retainer Block up against the Fixed Retainer Block so that their two beveled edges meet each other (Figure 2).
PAGE 3
Single Speaker Mount: Step 8: Attach a Speaker Mount to the Arm. Attach the selected mount’s center hole to the selected extension arm’s hole using the included ½13 x 3.5” or 4.5” long hex bolt, split lock washer, fender washer, friction washer, and Nyloc nut. Length of bolts to use depends on the type of mounts being installed. Make sure the friction washer is placed in between the arm and the mount (Figure 6). Rotate mounts/speaker assembly to desired angle then tighten bolts permanently.
PAGE 4
Step 15: Install Safety Cable Secure a safety cable to the pole or column, and then attach the other end of the safety cables to the speakers to bypass the mounting system.