BOLERO Instruction Manual Manuel d'instruction Handleiding Bedienungsanleitung Lighting Technologies M 1030 1106.01.
BOLERO Instruction Manual Lighting Technologies Page 1 Revision : 002
BOLERO Summary Installation Signal Connections Technical Specifications Options and Accessories Unpacking the desk Precautions Caution Connecting to the back panel 4 4 4 4 5 5 5 5 «GRAND MASTER» 6 Manual Section 6 Flash Keys Generating Manual Output Dual Preset Effect Section The Channel Buttons Speed Control START/STEP Button Level Control ON/OFF Button Direction Button Mode Button 6 7 8 9 9 9 9 9 10 10 10 Remote Control (option) 12 Analogue Output (option) 12 Analogue Output Card Installati
BOLERO Delivery - Unpacking Upon delivery of your equipment, open the packaging carefully and examine the material. If you observe any damage, contact the shipping company immediately, and have your complaint duly recorded. You may rest assured that your equipment left the factory in perfect condition. Check whether what you have received is in conformity with the delivery notice, and whether the notice is in conformity with your order.
BOLERO Installation The BOLERO is a professional lighting control desk, developed as per EN60950 safety standard. It is a class 1 equipment designed and manufactured to EN60950. To prevent any risk of electric shock do not open the desk, there are no user serviceable parts inside. Refer servicing to trained service personnel exclusively. Signal Connections GND 1 DATA - 2 DATA + 3 4 5 O O O O O O 1 GND O 2 DATA O 3 DATA + O4 O5 XLR5-MX dimmer dependent Cable : x 2 x 0,34 mm shielded Max.
BOLERO Unpacking the desk After removing the desk from it's box, check that the following items are included : • 1 BOLERO desk • 1 User manual (this document) • 1 * 5 pin XLR male connector for DMX512/1990 signal If any of the previous items are missing contact your supplier immediately. Retain the box and packing material for any future transportation or storage of the desk. Precautions WARNING To prevent fire or shock hazard, do not expose these units to rain or moisture.
BOLERO «GRAND MASTER» USING THE Grand Master SECTION The Grand Master section controls the output of the desk. If the «ON/OFF» button is pressed then all output from the desk is off, and the LED above the button is off. A second press of the button restores the output, and illuminates the LED. The Grand Master fader controls the overall output level of the desk. In it's lowest position (0) the output is off, as if the «ON/OFF» button had been pressed. In it's highest position (10) output is at maximum.
BOLERO Generating Manual Output Each group of Preset faders has a master control fader and on/off button. The master for Preset B works in reverse of that for Preset A, i.e. 100% is at the bottom and 0% is at the top of its travel, for Preset B. The «ON/OFF» buttons work in a similar fashion to the Grand Master «ON/OFF» button, in that they control whether the output from their respective Preset group is blacked out (LED off) or not.
BOLERO Dual Preset Dual Presets allow for the creation of two output settings on two different banks of faders, Preset A and Preset B. Either or both presets may be output from the desk with the highest value of each channel taking precedence.The active Preset(s) are shown by illuminating the corresponding LED. Either Preset may be blacked out using the corresponding «ON/OFF» button and the output level of each Preset is determined by the two master faders, labelled A and B.
BOLERO Effect Section A pre-programmed chase sequence may be selected from those available. The patterns available depend on whether a BOLERO 12 or a BOLERO 24 is being used. For the BOLERO 12 chase patterns 1 to 12 are available. On the BOLERO 24 patterns 1 to 24 may be used. The channels over which the chase runs may be individually selected. The Effect section controls use is detailed below. The Channel Buttons This button selects the channels over which the chosen pattern will operate.
BOLERO ON/OFF Button All the «ON/OFF» buttons on the desk have the same basic effect. They remove the effect of their associated section from the output on the stage, whithout effecting the processing of that section, i.e. in the Effect section if the «ON/OFF» button is pressed then the sections effect on the stage output is lost but the chase sequence will continue. A press of the «ON/OFF» button is confirmed by it's LED going out, another press of the button will reverse this action.
BOLERO Chase Pattern 1 Step 1 ● ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ Step 2 ❍ ● ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ Step 3 ❍ ❍ ● ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ Chase Pattern 13 Step 1 ● ● ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ Step 2 ● ● ● ● ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ Step 3 ● ● ● ● ● ● ❍ ❍ ❍ ❍ ❍ ❍ Chase Pattern 2 Step 1 ● ● ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ Step 2 ❍ ● ● ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ Step 3 ❍ ❍ ● ● ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ Chase Pattern 14 Step 1 ❍ ● ● ● ● ● ● ● ● ● ● ● Step 2 ● ❍ ● ● ● ● ● ● ● ● ● ● Step 3 ● ● ❍ ● ● ● ● ● ● ● ● ● Chase Pattern 3 Step 1 ● ● ● ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ Step 2 ❍ ● ● ●
BOLERO Remote Control (option) One of the options available for the BOLERO is the ability to remotely use the Effect section START/STEP button. AUX DIN 5 This operation is identical to that button on the desk itself, and is detailed in the relevant section of the manual. No button has preference over the other. The remote control is plugged into the AUX socket on the back panel. The remote START/STEP button will short pins 2 and 4 when used.
BOLERO Analogue Output Card Installation Instruction This assembly and desk contain static sensitive components. Installation should be undertaken using appropriate precautions. Turn the desk over onto it ' s front and remove the rear cover plate. Put this and the screws carefully to one side, to refit later. Using a sharp scalpel, or similar, cut out either one or both of the analogue output connector positions in the rear connector panel of the control desk.
BOLERO Rear View 1 2 3 4 5 Front View 19 20 13 14 15 16 6 11 12 21 29 30 24 25 26 27 7 8 9 Page 14 Revision : 002 10 17 18 22 23 28 31 Lighting Technologies
BOLERO Controls, Indicators and Connectors Rep.
BOLERO In Case of Difficulty FAULT POSSIBLE REMEDIES Desk fails to come on. Is power supply plugged into desk correctly ? Is power supply connected to mains supply ? Is mains supply switched on ? Manual section faders do not produce an output when pushed up. Has the Manual section been blacked out ? (ON/OFF) Has the Master section been blacked out ? (ON/OFF) Is the Master section fader off of 0 ? Manual section LED's do not mimic fader operation.
M-1030-4L-06h Belgium N.V. ADB-TTV Technologies S.A. (Group Headquarters) Leuvensesteenweg 585, B-1930 Zaventem Tel : 32.2.709.32.11 Fax : 32.2.709.32.80 E-Mail : adb@adblighting.com Deutschland ADB GmbH Dieselstraße 4, D-63165 Mühlheim am Main Tel : 49.6108.91.250 Fax : 49.6108.91.25.25 E-Mail : adblighting@t-online.de France ADB S.A.S. Sales office: 168/170, boulevard Camélinat F-92240 Malakoff Tel : 33.1.41.17.48.50 Fax : 33.1.42.53.54.76 E-Mail : adb.fr@adblighting.
