User's Manual
Table Of Contents
- interWave WaveNet Link CX User Manual
- One - System Description
- 1-1 General
- 1-2 System Overview
- 1-3 Features
- 1-4 LinkCX Basic Structure
- 1-4.1 Radio Links
- 1-4.2 Data Stream
- 1-4.3 LinkCX Models
- 1-4.4 Mounting and Antenna Alignment
- 1-4.5 Interface Connectors and Indicators
- 1-4.6 Cables
- 1-4.7 Integral Antenna
- 1-4.8 External Antenna
- 1-4.9 Configuration, Operation, and Monitoring
- 1-4.10 SNMP
- 1-4.11 LinkCX Network Management Architecture
- 1-4.12 NMS Connectivity
- 1-4.13 Web-Based GUI Access Security
- 1-4.14 GUI Functions
- 1-5 Typical Applications
- 1-5.1 Internet (ISP)
- 1-5.2 Private Network Wireless Bridged LANs and WANs
- 1-5.3 PCS/PCN and Cellular Networks
- 1-5.4 Wireless Local Loop Networks and Local Exchange Bypass
- 1-5.5 Business Bypass and Local Exchange Bypass
- 1-5.6 Backhaul for Wireless MTU and MTU Access
- 1-5.7 Wireless Mesh Backhaul Networks
- 1-5.8 Wireless ATM Mesh Distribution with StreamNet
- 1-6 Specifications
- Two - Installation Steering Guide
- Three - Installation Planning
- Four - Installing the Link CX
- Five - Final Link CX Setup
- Six - Monitoring and Trend Analysis
- Seven - Troubleshooting the Link CX
- Appendix 1 - Interface Cable Pinouts
- Appendix 2 - Technical Specifications
- Appendix 3 - Using the Web-Based GUI User Interface
- Appendix 4 - Grounding and Lightning Protection
- Appendix 4 - Enterprise MIBs and Traps
94 Link CX User Manual, Version A
Table A2-2 Link CX-DSX DS-3 or Ethernet Version (5.8 GHz)
General
Frequency Range 5.725-5.825 GHz
Compliance Complies with FCC Ruling Part 15.247
Capacity
Full-duplex DS-3, per Bellcore GR-499-CORE, or
45 Mbps Ethernet, per IEEE 802.3
Emission Bandwidth 16 MHz
Channel Center Frequencies
• Channel 1 (Tx Low/Rx High)
• Channel 1 (Tx High/Rx Low)
• Channel 2 (Tx Low/Rx High)
• Channel 2 (Tx High/Rx Low)
Transmit--5.737 GHz/Receive--5.797 GHz
Transmit--5.797 GHz/Receive--5.737 GHz
Transmit--5.753 GHz/Receive--5.813 GHz
Transmit--5.813 GHz/Receive--5.753 GHz
Modulation Type 16 QAM
Factory-Supplied Coaxial Cable 2 m (6.6 ft.) N-Type Male to N-Type Male
Transmitter
Maximum RMS Power Output +16.0 dBm
Power Output Stability +/- 2 dB
Frequency Stability +/- 5 ppm
Transmit Duty Cycle 100%
Emissions Mask & Spurious and
Harmonic Output
Per FCC CFR 47 Part 15.407b3
Channel Frequency Selection Software-controlled
Automatic Tx Power Control (ATPC)
Maintains a constant Carrier-to-Noise Ratio at both
ends of a link, operator enabled ON or OFF
Transmitter Attenuation Range
0-30.0 dB in 1 dB steps, and Mute 40 dB, operator
controlled
Receiver
Type Double Heterodyne
Error Correction FEC Reed Solomon Decoding
Sensitivity at 10
-6
BER -78 dBm state guaranteed
Typical Unfaded BER 10
-10
Frequency Stability +/- 5 ppm
Channel Frequency Selection Software-controlled