User's Manual
Table Of Contents
- interWave WaveNet Link CX User Manual
- One - System Description
- 1-1 General
- 1-2 System Overview
- 1-3 Features
- 1-4 LinkCX Basic Structure
- 1-4.1 Radio Links
- 1-4.2 Data Stream
- 1-4.3 LinkCX Models
- 1-4.4 Mounting and Antenna Alignment
- 1-4.5 Interface Connectors and Indicators
- 1-4.6 Cables
- 1-4.7 Integral Antenna
- 1-4.8 External Antenna
- 1-4.9 Configuration, Operation, and Monitoring
- 1-4.10 SNMP
- 1-4.11 LinkCX Network Management Architecture
- 1-4.12 NMS Connectivity
- 1-4.13 Web-Based GUI Access Security
- 1-4.14 GUI Functions
- 1-5 Typical Applications
- 1-5.1 Internet (ISP)
- 1-5.2 Private Network Wireless Bridged LANs and WANs
- 1-5.3 PCS/PCN and Cellular Networks
- 1-5.4 Wireless Local Loop Networks and Local Exchange Bypass
- 1-5.5 Business Bypass and Local Exchange Bypass
- 1-5.6 Backhaul for Wireless MTU and MTU Access
- 1-5.7 Wireless Mesh Backhaul Networks
- 1-5.8 Wireless ATM Mesh Distribution with StreamNet
- 1-6 Specifications
- Two - Installation Steering Guide
- Three - Installation Planning
- Four - Installing the Link CX
- Five - Final Link CX Setup
- Six - Monitoring and Trend Analysis
- Seven - Troubleshooting the Link CX
- Appendix 1 - Interface Cable Pinouts
- Appendix 2 - Technical Specifications
- Appendix 3 - Using the Web-Based GUI User Interface
- Appendix 4 - Grounding and Lightning Protection
- Appendix 4 - Enterprise MIBs and Traps
8 Link CX User Manual, Version A
Table 1-2 Link CX Interface Connectors and Indicators
No. Name Component Description From Note
1POWER
Male 4-Pin
Circular
Connector
Power input plug Power Supply
Accepts ±21 to
±60 VDC
2 CRAFT
Female 4-Pin
Circular
Connector
RS-232
receptacle
Asynchronous
laptop port
1200 to 115,200 baud,
used only for tech
support troubleshooting
3 RSSI
Female BNC
Connector
Receive Signal
Level Indicator
Voltmeter
Verifies RF signal
strength, used to align
antenna
4OUT
Female TNC
Connector
DS-3 data from
the radio link
DS-3 data
equipment
--
5IN
Female TNC
Connector
DS-3 data to the
radio link
DS-3 data
equipment
--
6 ETHERNET 2
Female 4-Pin
Circular
Connector
10/100Base-T
transmit and
receive
receptacle
Ethernet
equipment
For Ethernet data or link
to SNMP or Web
manager, or use to
daisy-chain Ethernet
port to next Link CX in
cascade
7 ETHERNET 1
Female 4-Pin
Circular
Connector
10/100Base-T
transmit and
receive
receptacle
Ethernet
equipment
(Same as ETHERNET 2)
8
ANTENNA
PORT (Opt.)
Female
N-type
Connector
50 Ohm RF
receptacle
External
antenna
Only equipped on
external-antenna
models, on far side of
chassis
9
PWR/LCL ALM
RF LINK
DATA
ENET 2
ENET 1
Green LED
Green LED
Green LED
Green LED
Green LED
Power/Local
Alarm Status
Radio Link Status
DS-3 Status
Ethernet Status
Ethernet Status
--
ON = Power OK, no
alarm, Flashing = Local
alarm, OFF = Power off.
ON = Rcv. OK,
OFF = Link Alarm.
ON = OK (no LOS),
OFF = LOS.
ON = OK, Flashing =
data, OFF = No conn.
ON = OK, Flashing =
data, OFF = No conn.
Note: For connector pinouts, refer to Appendix 1.