User Manual

ManualsBrandsADC Telecommunications ManualsElectronicsDigivance Long Range Coverage Solution SMR System

ADCP-75-115 • Issue A • August 2001

1162625 Rev A Page 1

2001,

ADC

Telecommunications,

Inc.

Digivance

™

Long Range Coverage Solution

Single Band SMR Remote Unit

Installation Instructions

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1 DESCRIPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2 UNPACKING AND INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3 STM USER INTERFACE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4 LPA USER INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

5 WDM USER INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

6 INSTALLATION PROCEDURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

6.1 STM Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

6.2 LPA Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

6.3 Battery Backup Kit Installation (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

6.4 WDM Installation (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Content Page

16752-A

DRAFT

FCC ID: F8I-DVLRCSSMR

Summary of content (17 pages)

PAGE 1
FCC ID: F8I-DVLRCSSMR ADCP-75-115 • Issue A • August 2001 Digivance™ Long Range Coverage Solution Single Band SMR Remote Unit Installation Instructions DRAFT 16752-A Content Page INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1162625 Rev A 1 DESCRIPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 2
ADCP-75-115 • Issue A • August 2001 7 8 CABLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7.1 AC Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7.2 Routing Pre-Connectorized Indoor/Outdoor Fiber Optic Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 7.
PAGE 3
ADCP-75-115 • Issue A • August 2001 The ADC-provided RU cable installation loose parts hardware are listed in Table 1. Table 1. Cable Installation Loose Parts Hardware ITEM QUANTITY brown cable grip ring, 0.5-inch to 0.63-inch cable diameter 1 yellow cable grip ring, 0.63-inch to 0.75-inch cable diameter 1 purple cable grip ring, 0.75-inch to 0.88-inch cable diameter 1 neoprene bushing-, 0.500 to 0.625-inch cable diameter 1 neoprene bushing, 0.625 to 0.
PAGE 4
ADCP-75-115 • Issue A • August 2001 Admonishments Important safety admonishments are used throughout this manual to warn of possible hazards to persons or equipment. An admonishment identifies a possible hazard and then explains what may happen if the hazard is not avoided. The admonishments — in the form of Dangers, Warnings, and Cautions — must be followed at all times.
PAGE 5
ADCP-75-115 • Issue A • August 2001 The following optional components may also be shipped with the basic component package: • Battery Backup Kit • Wave Division Multiplexer (WDM) Kit 3 STM USER INTERFACE The STM user interface consists of the various connectors, switches, and LEDs that are provided on the STM front panel. The STM user interface points are indicated in Figure 1 and described in Table 2.
PAGE 6
ADCP-75-115 • Issue A • August 2001 Table 2. Spectrum Transport Module User Interface, continued REF NO FUNCTIONAL DESCRIPTION USER INTERFACE DESIGNATION DEVICE 3 PORT 3 (diversity unit only) SC connector Connection point for the reverse path diversity fiber optic link. 4 I/O On/Off rocker switch Provides AC power on/off control. 5 No designation 3-wire AC power cord connector Connection point for the AC power cord.
PAGE 7
ADCP-75-115 • Issue A • August 2001 4 LPA USER INTERFACE The LPA user interface consists of the various LEDs, message displays, and switches that are provided on the LPA front panel. The LPA user interface points are described in Table 3 and indicated in Figure 2. Table 3.
PAGE 8
ADCP-75-115 • Issue A • August 2001 5 WDM USER INTERFACE The WDM user interface consists of a connector and two trailing cables provided on the WDM front panel. The WDM user interface connectors are described in Table 4 and indicated in Figure 2. Table 4. Wave Division Multiplexer (WDM) User Interface REF NO USER INTERFACE DESIGNATION FUNCTIONAL DESCRIPTION DEVICE 1 WDM SC Connector Connection point for the bi-directional indoor/ outdoor cable from the splice tray enclosure.
PAGE 9
ADCP-75-115 • Issue A • August 2001 2. Gently slide the STM into the cabinet at the location shown in Figure 4. If resistance is encountered, remove the STM and check the alignment of the mating connector on the backplane. 3. Tighten the two compression screws that secure the STM to the cabinet mounting shelf. 16813-A SPECTRUM TRANSPORT MODULE (STM) LINEAR POWER AMPLIFIER (LPA) BATTERY BACKUP (OPTIONAL) Figure 4. Installing RU Components 6.
PAGE 10
ADCP-75-115 • Issue A • August 2001 6.3 Battery Backup Kit Installation (Optional) Caution: The battery pack weighs approximately 75 lb (34 kg). Enlist sufficient aid to lift the battery pack into position inside the cabinet. Perform the following steps to install the optional battery pack: 1. Slide the battery pack into position on the heated tray within the cabinet as shown in Figure 4. 2.
PAGE 11
ADCP-75-115 • Issue A • August 2001 wired for 120 Vac but can be converted to 240 Vac operation through the installation of a 240 Vac outlet kit (accessory item). Connect the AC power wiring as follows: 1. Obtain access to the internal power wiring harness inside the auxilary junction box by loosening the four screws securing the auxiliary box cover, pulling up and removing the cover. see Figure 5. 2.
PAGE 12
ADCP-75-115 • Issue A • August 2001 CABLE STORAGE SPOOLS FIBER PORT (HUBBELL CONNECTOR BODY) PRIMARY ANTENNA DIVERSITY ANTENNA PORT 16790-A BUSHING SPLIT RING COMPRESSION NUT INDOOR/ OUTDOOR CABLE AC SUPPLY PORT TO APPROVED GROUND SOURCE DRAIN HOLE CABINET GROUND LUG Figure 6. Cable Entry Ports on Cabinet 3. A grounding lug is provided on the underside of the cabinet. Connect a ground wire to this lug as required to meet local codes. 4.
PAGE 13
ADCP-75-115 • Issue A • August 2001 7.2 Routing Pre-Connectorized Indoor/Outdoor Fiber Optic Cable Fiber optic cable termination typically consists of routing a pre-connectorized indoor/outdoor fiber optic cable between the cabinet and an external splice tray enclosure, securing the cable to the cabinet, breaking out the individual jacketed pigtail fibers inside the cabinet, and connecting the fibers to the WDM (optional) or STM.
PAGE 14
ADCP-75-115 • Issue A • August 2001 Warning: To avoid exposure to to invisible laser radiation, do not look into the ends of any optical fiber or bulkhead connector. Never assume laser power is turned off or that the fiber is disconnected at the other end. Use an optical power meter to identify active fibers. Always place a protective cap over any unused bulkhead connector or optical fiber connector. 1.
PAGE 15
ADCP-75-115 • Issue A • August 2001 Diversity Cable kit. The Diversity jumper cable must be attached to the Diversity connector on the STM (refer to item 17 on Figure 1). Note: To comply with Maximum Permissible Exposure (MPE) requirements, the maximum composite output from the antenna cannot exceed 1000 Watts EIRP and the antenna must be permanently installed in a fixed location that provides at least 6 meters (20 feet) of separation from all persons. 7.
PAGE 16
ADCP-75-115 • Issue A • August 2001 16791-A Figure 9. Connectorizing Door Open Switch 9 FINAL TEST AND ADJUSTMENTS When the installation is completed, refer to the Digivance Single Band LRCS Installation and Operation Manual (ADCP-75-116) for system turn-up and test procedures. This section under construction Page 16 © 2001, ADC Telecommunications, Inc.
PAGE 17
ADCP-75-115 • Issue A • August 2001 10 CUSTOMER INFORMATION AND ASSISTANCE For customers wanting information on ADC products or help in using them, ADC offers the services listed below. To obtain any of these services by telephone, first dial the central ADC telephone number, then dial the extension provided below. The central number for calls originating in the U.S.A. or Canada is 1-800-366-3891. For calls originating outside the U.S.A. or Canada, dial country code “1” then dial 952-946-3000.