User's Manual

ManualsBrandsADC Telecommunications ManualsElectronicsFlexWaveÂ™ URH - AWS

Mailing Address: P.O. Box 1101, Minneapolis, Minnesota 55440-1101

World Headquarters: Minneapolis, Minnesota USA +1.952.938.8080 www.adc.com

Hardware Installation – FlexWave

URH - Preliminary

FlexWave™ URH

Operation and Maintenance Manual - Preliminary

PRODUCT DESCRIPTION

This publication provides basic information about the FlexWave™ URH installation.

The FlexWave URH provides the same functionality as the ADC Wireless family of distributed

antenna systems (DAS). However, the URH platform implements three single band DAS

system capability into one single chassis. The system is comprised of a host and remote

chassis with a fiber optic interface. The host chassis is intended for central office equipment

enclosure/indoor use. This remote chassis is functional for indoor and outdoor installation.

The remote chassis provides the degree of protection specified by NEMA 6 and IP67 as

defined by IEC Publication 60529.

INSTALLATION OVERVIEW

REMOTE ENCLOSURE HOST ENCLOSURE

Summary of content (7 pages)

PAGE 1
Hardware Installation – FlexWaveTM URH - Preliminary FlexWave™ URH Operation and Maintenance Manual - Preliminary PRODUCT DESCRIPTION This publication provides basic information about the FlexWave™ URH installation. The FlexWave URH provides the same functionality as the ADC Wireless family of distributed antenna systems (DAS). However, the URH platform implements three single band DAS system capability into one single chassis.
PAGE 2
Mounting The FlexWave™ URH host chassis is 19/23 inch equipment rack mountable requiring 3 RU spacing. The Flexwave URH remote chassis has a mounting bracket provided with each unit. The mounting bracket is banded to the pole with three 1.0” wide stainless steel bands. The chassis is then hung from the bracket by means of protrusions and keyhole slots. Once the chassis is in place, it is further secured to the mounting bracket with two 7/16” stainless steel hex bolts. Mailing Address: P.O.
PAGE 3
SPECIFICATIONS RF Specification Supported Frequency Blocks Bandwidth Frequency Band Supported Digital Simulcast Diversity Receive Propagation Delay System Delay Delay Management Digital Noise Figure Noise Figure Input IP3 Optical Specifications Optical Budget Digital Transport Rate Output Power Output Power per Band 1-3 per Remote Unit; 1-8 per Host Unit 1.
PAGE 4
STANDARDS CERTIFICATION FCC: This equipment complies with the applicable sections of Title 47 CFR Part 15 (Host unit), Part 22 (800 MHz Cellular), Part 24 (1900 MHz - PCS), and Part 90 (800/900 - SMR) IC: This equipment complies with the applicable sections of RSS-131. The term “IC:” before the radio certification number only signifies that Industry Canada Technical Specifications were met. The Manufacturer's rated output power of this equipment is for single carrier operation.
PAGE 5
AC Power Wiring Installation A 15-foot connectorized 3-wire cable is provided for the AC power connections. The connectorized end of the cable connects to the AC power port located on the bottom of the enclosure. The stub end of the cable must be routed to an external junction box (not provided) for permanent connection to the AC power system wiring. The socket outlet shall be installed near the equipment and shall be easily accessible.
PAGE 6
3. Secure the cable between the AC power port and the AC power junction box per local practice. Leave sufficient slack in the cable to allow it to be easily connected and disconnected from the AC power port. 4. Install any AC power supply wires that may be required between the AC junction box and the AC circuit breaker box. 5. Connect the AC power cable wires to the AC power supply wires. Refer to Figure 15 to identify the color code and wire designations. Figure 15. AC Power Cable Connections 6.
PAGE 7
10. Connect the power cable connector to the AC power port. 11. Tighten coupling nut until the green band at the top of the connector body is visible. Mailing Address: P.O. Box 1101, Minneapolis, Minnesota 55440-1101 World Headquarters: Minneapolis, Minnesota USA +1.952.938.8080 www.adc.