InterReach Spectrum™ Remote Access Unit Installation Guide - Preliminary Update - Issue 3 ADCP-77-168 Issue 3 July 2012 Main Remote Access Unit Secondary Remote Access Unit D-620731-0-20 Rev C
Copyright © 2012 TE Connectivity, Inc. All Rights Reserved. Information contained in this document is company private to TE Connectivity Ltd., and shall not be modified, used, copied, reproduced or disclosed in whole or in part without the written consent of TE. Trademark Information FlexWave, FlexWave Prism, InterReach Spectrum, Universal Connectivity, and TE connectivity (logo) are trademarks.
TABLE OF CONTENTS Preface .................................................................................................................................................................2 Revision History...................................................................................................................................................... 2 InterReach Spectrum User Documentation ...........................................................................................................
Preface PREFACE This manual provides installation instructions for InterReach Spectrum® Remote Access Units (RAUs). Table 1 lists the RAUs that are supported in this document. Table 1.
InterReach Spectrum User Documentation InterReach Spectrum User Documentation The InterReach Spectrum user documentation is intended for system administrators, engineers and installers responsible for planning, administering, configuring, and maintaining TE Connectivity InterReach Spectrum systems. Table 2 lists the manuals that correspond to this InterReach Spectrum release. Table 2.
Preface Standards Certification FCC: This equipment complies with the applicable sections of Title 47 CFR, Part 22 (800 MHz Cellular), Part 24 (1900 MHz ‐ PCS), Part 90 (800/900 ‐ SMR), and Part 27 (700 MHz, 2100 MHz ‐ AWS). IC: This equipment complies with the applicable sections of RSS‐131 (800/900 – SMR), RSS‐132 (800 ‐ Cellular), and RSS‐133 (1900 – PCS). The term “IC:” before the radio certification number only signifies that Industry Canada Technical Specifications were met.
Standards Certification PRODUCT OVERVIEW InterReach Spectrum supports up to eight frequency bands in a single system. Each antenna location supports those bands in modular, group pairings. Each location includes a Main Remote Access Unit (MRAU), which can power up to three additional Secondary Remote Access Units (SRAUs). An MRAU supports two frequency bands, and each SRAU can support up to two frequency bands, for a total of up to eight frequency bands.
Product Overview Main Remote Access Units The Main Remote Access Unit (MRAU) receives FWD IF signals from an IF Expansion Unit (IFEU), which is part of the Spectrum Expansion Module Group, using 75 CATV cable. The MRAU converts the IF signals to RF and sends them to a passive RF antenna using 50 coaxial cable. The MRAU also receives configuration information and power from and sends its status information to the IFEU. The MRAU receives REV RF signals from a passive RF antenna using 50 coaxial cable.
Main Remote Access Units MRAU LEDs REV IF OUT REV SECONDARY PORTS 1 2 3 1 Ref # LED 1 2 3 4 5 FWD SECONDARY PORT (1 - 3) 2 REV SECONDARY PORT (1 - 3) FWD IF IN STATUS FWD SECONDARY PORTS 1 2 3 3 FWD IF IN 4 5 LED Color Description • Green • Downstream unit correctly connected; unit has no alarms or a Minor alarm is active. • Blinking Green • SRAU or band is set out-of-service. • Yellow • FWD cable connected to SRAU, no REV cable connected.
Product Overview Secondary Remote Access Units A Secondary Remote Access Unit (SRAU) receives FWD IF signals from the MRAU, using 75 CATV cable. The SRAU converts the IF signals to RF and sends them to a passive RF antenna using 50 coaxial cable. The SRAU, through the MRAU, also receives configuration information and power from and sends its status information to the IFEU. The SRAU receives REV RF signals from a passive RF antenna using 50 coaxial cable.
Secondary Remote Access Units SRAU LEDs SECONDARY SECONDARY REV Ref # LED 1 2 3 STATUS 1 2 3 LED Color Description • Green • SRAU receiving communications from the IFEU. • Red • SRAU has not received communications from the IFEU for more than 90 seconds. • Off • During initial power up, SRAU is powering up and waiting for IFEU communications. • Green • Unit has no alarms or a Minor alarm is active. • Blinking Green • Unit or band is set out-of-service. • Red • Major alarm detected.
Product Overview RAU N Connectors Each RAU also has one or two 50‐ N‐type connectors that connect to a passive antenna. Table 3 lists the number of N‐type connectors available on each RAU model. Table 3.
Mount the RAUs and Antennas INSTALL THE RAUS AND ANTENNAS Follow the steps in the order provided to install the RAUs and antennas. Mount the RAUs and Antennas General Safety Precautions CAUTION! Wet conditions increase the potential for receiving an electrical shock when installing or using electrically powered equipment. To prevent electrical shock, never install or use electrical equipment in a wet location or during a lightning storm.
Install the RAUs and Antennas 3 Connect a passive multi‐band antenna to the N connector on each RAU using coaxial cable with the least amount of loss possible. (See “Appendix C: Omni Antenna” on page 24 for information on the Omni Antenna ports.) CAUTION! Firmly hand‐tighten the N connector. DO NOT over‐tighten the connector.
Connect the IFEU to the MRAU IFEU Step 6a To an antenna MRAU REV IF OUT REV SECONDARY PORTS 1 2 3 LINK STATUS Step 6c InterReach Spectrum Remote Access Unit Installation Guide - Preliminary Update for Issue 3 ADCP-77-168 • Issue 3 • December 2011 FWD SECONDARY PORTS 1 2 3 FWD IF IN Step 6b Page 13 © 2012 TE Connectivity Ltd.
Install the RAUs and Antennas Connect the MRAU to SRAUs CAUTION! 7 To prevent interference, do not install an 850/1900 MRAU antenna near an 800/900 SRAU. The 850 MHz band must be 20 feet away from the 800/1900 SRAU’s passive antenna. Use one of the following 6’ and 20’ CATV RG6 jumpers, available for purchase from TE Connectivity, to connect an MRAU to SRAUs. TE Connectivity Part Number Description Note 300469-0 6’ RG-6 Cable; F Male to F Male CATV cable that connects the MRAU to SRAUs.
Configure the MRAUs and SRAUs 10 Repeat Step 9 to install up to two more SRAUs, as per system design.
Appendix A: Specifications APPENDIX A: SPECIFICATIONS Remote Access Unit Specifications Operating Temp ‐25°C to +50°C Storage Temperature ‐40°C to +70°C Humidity 10% to 90% non‐condensing Dimensions 11.50" x 9.00" x 3.50" Weight 7.49 Pounds Power Source +54Vdc (from IFEU) Spectrum System Specifications RF Specification Supported Frequency Blocks 2 per Remote Antenna Unit; 1‐8 per Host Unit Bandwidth 1.
Spectrum System Specifications Nominal Passband Gains RF Frequency TX RX Bandwidth 869-894 824-849 Gain (dB) 40 30 850 Cell 800 SMR Bandwidth 851-869 806-824 Gain (dB) 40 30 Bandwidth 935-940 896-901 Gain (dB) 40 30 Bandwidth 1930-1995 1850-1915 Gain (dB) 40 30 Bandwidth 2110-2155 1710-1755 Gain (dB) 40 30 Bandwidth 746-756 776-786 Gain (dB) 40 30 900 SMR 1900 PCS 2100 AWS 700 Upper C 700 Lower ABC Bandwidth 728-746 Gain (dB) 40 698-716 30 Output Power Output
Appendix A: Specifications Composite Power Out of RAU RF Frequency 850 Cell 800 SMR 900 SMR 1900 PCS 2100 AWS Number of RF Carriers TX RX 1 2 4 869-894 824-849 26.0 20.0 14.0 9.0 5.5 GSM 23.0 17.5 12.0 8.0 5.0 EDGE 18.0 15.0 12.0 9.0 6.0 CDMA 18.0 15.0 12.0 9.0 WCDMA 18.0 15.0 12.0 9.0 LTE 851-869 935-940 1930-1995 2110-2155 806-824 896-901 1850-1915 1710-1755 8 16 17.5 14.0 10.0 6.5 iDEN 26.0 19.5 13.5 8.5 APCO 25 C4FM 18.0 15.0 12.0 9.
CATV Cable Requirements APPENDIX B: 75‐OHM CATV CABLE The 75‐Ohm CATV Cable: • connects the IFEU to MRAU(s) and the MRAU(s) to the SRAU(s) • transmits (FWD) multiband and receives (REV) IF signals • delivers DC electrical power to the RAUs. The Spectrum IFEU DC voltage output is +54Vdc nominal. If the IFEU reaches its current limit, a current‐limiting circuit protects it. • carries configuration and status information • uses 75 type‐F connectors with captive center pins.
Appendix B: 75-Ohm CATV Cable • Use only RG‐6 CATV cable between the MRAU and SRAU, the lengths of which are listed below. RG-6 Cable Meters Feet Typical 2 6.56 800/900 iDEN to 850 CELL 6 19.68 800 AWS to 850 CELL 6 19.68 Belden 1695A Coax Specifications Description RG‐6/U type, 18 AWG solid 0.040‐inch bare copper conductor, plenum, foam FEP insulation, Duofoil® + tinned copper braid shield (95% coverage), Flamarrest® jacket.
Belden 1695A Coax Specifications Overall Nominal Electrical Characteristics Characteristic Impedance 75.000 Inductance 0.103 H/ft. Capacitance Conductor to Shield 16.100 (pF/ft.) Velocity of Propagation 82 (%) Delay 1.240 (ns/ft.) Conductor DC Resistance 6.400 @ 20°C (/1000 ft.) Outer Shield DC Resistance 2.800 @ 20°C (/1000 ft.) Attenuation Freq. (MHz) Attenuation (dB/100 ft.) 1.000 0.240 3.580 0.450 5.000 0.550 7.000 0.650 10.000 0.750 67.500 1.740 71.500 1.780 88.500 1.
Appendix B: 75-Ohm CATV Cable Belden 7732A Coax Specifications Description RG‐11/U type, 14 AWG solid 0.064‐inch bare copper conductor, plenum, foam FEP insulation, Duofoil® + tinned copper braid shield (95% coverage), fluorocopolymer jacket. Overall Physical Characteristics Conductor One Coax 18 AWG Solid stranding Bare Copper (BC) conductor material 0.064‐inch diameter Insulation Teflon® Foam Fluorinated Ethylene Propylene (FFEP) 0.
Belden 7732A Coax Specifications Overall Nominal Electrical Characteristics Characteristic Impedance 75.000 Inductance 0.091 H/ft. Capacitance Conductor to Shield 16.300 (pF/ft.) Velocity of Propagation 83 (%) Delay 1.220 (ns/ft.) Conductor DC Resistance 2.500 @ 20°C (/1000 ft.) Outer Shield DC Resistance 1.600 @ 20°C (/1000 ft.) Attenuation Freq. (MHz) Attenuation (dB/100 ft.) 1.000 0.150 3.580 0.260 5.000 0.300 7.000 0.340 10.000 0.400 67.500 1.200 71.500 1.240 88.500 1.
Appendix C: Omni Antenna APPENDIX C: OMNI ANTENNA The Omni Antenna (4214‐M727), shown in Figure 3, is a round radome with the following specifications: • 8.5‐inch diameter • 1.65‐inch height • 72‐inch pigtails that are plenum‐rated cables with N (male) connectors Figure 3. Omni Antenna NOTE: Two antennas per RAU is required for MIMO performance.
Belden 7732A Coax Specifications APPENDIX D: CONTACTING TE CONNECTIVITY PHONE U.S.A.
Appendix D: Contacting TE Connectivity Page 26 © 2012 TE Connectivity Ltd InterReach Spectrum Remote Access Unit Installation Guide - Preliminary Update for Issue 3 ADCP-77-168 • Issue 3 • December 2011
