>4DCOM details you can hear GCD-700 CD Player OWNER’S MANUAL
WARNING NOTICE To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. A CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN A Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel.
INTRODUCTION Please read the operating instructions for your new GCD-700 thoroughly before connecting or attempting to operate the unit. For your own benefit, follow all the instructions in this manual and save it for future reference. Your AIX30M GCD-700 features some of the most advanced thinking in compact disc player design.
UNPACKING Before your new GCD-700 left our factory, it was carefully inspected for physical imperfections and tested for all electrical parameters as a routine part of ADCOM's systematic quality control. This, along with full operational and mechanical testing, should ensure a product flawless in both appearance and performance. After you have unpacked the GCD-700, inspect it for physical damage.
FIXED OUTPUT ® The decoded, analog audio signal is available at this output at a level compatible with most preamplifiers, tuner/preamps, and receivers. Simply connect one end of the supplied audio cable to the FIXED OUTPUT terminal of the GCD-700, left (L) and right (R), and the other end to the CD, AUX, or TAPE IN/PLAY input terminals, left (L) and right (R) of the preamplifier or receiver.
f^RONT PANEL CONTROLS Please refer to the diagram of the front panel and the diagram of the Remote Control Transmitter RC-700CD on page 7 to identify the controls and their functions. ® ® Gl (E) ® d) ® FRONT PANEL DIAGRAM POWER ® Turns the GCD-700 on and off. When initially powered up the display will show the last volume setting, for further information see the Remote Control Volume +1- section.
REMOTE CONTROL SENSOR S) Receives the infrared signal from the RC-700CD Remote Control. Aim the remote control here when using it. DISC 1 - DISC-5 (D These controls are used to select the disc that you want to play or program. REPEAT m This button is used to select the desired repeat mode. The various modes are indicated by the status lights.
DISC SKIP Oi This button is used to skip over to the next disc. It works with the drawer in the open or closed position and must be used when loading a disc in the rear-most position of the disc tray, this button will not operate when the drawer is open and a disc is playing or if a disc was playing when the drawer was opened. CAUTION tXD NOT ATTEMPT TO MANUALLY ROTATE THE DISC TRAY AS DAMAGE MAY RESULT.
• Select the disc you want to want to program and listen to by using DISC 1 though DISC 5 buttons. • Press the TRACK SELECTION button that corresponds to the track that you want to program and listen to. • Repeat steps 3 and 4 above as required until you have programmed all the desired tracks. • Press PLAY to start listening to the selections you have programmed. If you now use the FORWARD or REVERSE SEARCH controls, the player will advance or skip backwards through only the programmed tracks.
NOTE THE NORMAL RANGE OF THE REMOTE CONTROL IS 25 FEET OR APPROXIMATELY 8 METERS AND THE ANGLE OF OPERATION IS 30 DEGREES FROM THE CENTER OF THE REMOTE SENSOR WINDOW LOCATED ON THE FRONT PANEL OF THE UNIT. CAUTION DO NOT PRESS THE BUTTONS ON THE REMOTE CONTROL AND THE CONTROLS ON THE FRONT PANEL AT THE SAME TIME. DOING THIS COULD CAUSE A MALFUNCTION. PLAY® Press this button to start playing a disc. PAUSE m Press this button to temporarily stop playing a disc.
DISC SKIP +/- m Press this button to skip over to the next disc in either direction. This control can be used with the drawer in the open position when loading a disc in the rear-most position. DISC 1 • DISC 5 m Press the appropriate button to select the disc that you want to play or program. CALL® Press this button to browse through the tracks that have been programmed into the GCD-700’s memory. See the section on PROGRAMMING THE GCD-700 for further details.
Do not move or tilt the player when discs are loaded in the drawer as damage to the player and/or discs may result. Make sure the player is turned off, and remove the power cord from its AC power source if you plan to leave the system unattended for long periods of time.
player does not play through the stereo system: • Make sure the correct output of the player, FIXED, VARIABLE, or DIGITAL is connected to the proper input of the system. • Be certain the selector switch on the preamplifier or receiver is set to the input which the GCD-700 is connected to. • If using the VARIABLE output, make sure the level is not at its lowest setting. Player does not operate when the remote is used: • Make sure the batteries in the RC-700CD remote control are not dead.
Product update from ADCOM... Your GCD-700 has a new, more ergonomically designed remote control. All features are retained with improved layout. Please refer to this sheet to Identify button locations. CD700 insert vl.
GCD-700 TECHNICAL SPECIFICATIONS ELECTRICAL FREQUENCY RESPONSE (+0, -0.5 dB):................................................................................................................................................20 Hz - 20 kHz SIGNAL TO NOISE RATIO (“A” Weighted):..................................................................................................................................................... > 100 dB DYNAMIC RANGE;..................................................................
>OCOM' DM5093 10 Timber Lane Marlboro, NJ 07746 USA Tel: 732-683-2356 Fax: 732-683-9790 Web: www.adcom.
