Instructions

ManualsBrandsaddon ManualsOptical Cableaddon Q56-2Q56-200GB-AOC20MLZ-AO Active Optical Cable

www.addonnetworks.com Phone: 877.292.1701 Rev:1121 |

Q56-2Q56-200GB-AOC20MLZ-AO

MSA and TAA Compliant 200G-AOC QSFP56 to 2xQSFP56 Active Optical Cable (850nm, MMF, 20m, LSZH)

Features

•

Low latency DSP-free electronics-based CDR

•

Multi-data rate up to 56.15 Gb/s per lane

•

PAM4 modulation

•

Single 3.3 V power supply

•

Low power consumption: 3.6W on 200G end with all CDRs enabled

•

Up to 20m length

•

SFF-8665 compliant

•

SFF-8636 compliant I2C management interface

•

Operating case temperature: 0◦C to 70◦C

•

Hot pluggable

•

RoHS/REACH compliant

•

TUV-certified

•

LSZH, Aqua cable

Application

•

IEEE 802.3cd 200GBASE SR4

•

Datacenter: servers, switches, storages and NIC

adapters

•

Proprietary HPC interconnections

Product Description

This is an MSA compliant 200GBase-AOC QSFP56 to 2xQSFP56 active optical cable that operates over multi-

mode fiber with a maximum reach of 20.0m (65.6ft). At a wavelength of 850nm, it has been programmed,

uniquely serialized, and data-traffic and application tested to ensure it is 100% compliant and functional. This

active optical cable is TAA (Trade Agreements Act) compliant, and is built to comply with MSA (Multi-Source

Agreement) standards. We stand behind the quality of our products and proudly offer a limited lifetime

warranty.

AddOn’s active optical cables are RoHS compliant and lead-free.

TAA refers to the Trade Agreements Act (19 U.S.C. & 2501-2581), which is intended to foster

fair and open international trade. TAA requires that the U.S. Government may acquire only

“U.S. – made or designated country end products.”

Summary of content (8 pages)

PAGE 1
Q56-2Q56-200GB-AOC20MLZ-AO MSA and TAA Compliant 200G-AOC QSFP56 to 2xQSFP56 Active Optical Cable (850nm, MMF, 20m, LSZH) Features • Low latency DSP-free electronics-based CDR • Multi-data rate up to 56.15 Gb/s per lane • PAM4 modulation • Single 3.3 V power supply • Low power consumption: 3.
PAGE 2
Absolute Maximum Ratings Parameter Symbol Min Supply Voltage Vin 0 Input Swing Vin-max Storage Temperature (Ambient) Tstc Relative Humidity RH Typ. Max. Unit 4.0 V 1500 mVpp -40 85 °C 5 85 % Recommended Operating Specifications Parameter Symbol Min Operating Case Temperature Top 0 Power Supply Voltage Vcc 3.15 Power Supply Current Power Consumption Typ. Max. Unit Notes 70 °C 3.30 3.47 V 1250 mA 1 mA 1 200G End ICC 1100 100G End ICC 750 200G End P 3.
PAGE 3
Active Optical Cable Specifications Parameter Value Unit Cable Diameter LSZH: Ø3.0 ± 0.15 mm Minimum Bend Radius 30 mm Length Tolerance +300 / –0 mm Cable Jacket LSZH, Aqua Note Without tension Electrical Pin-Out Details www.addonnetworks.com Phone: 877.292.
PAGE 4
Pin Descriptions Pin Logic 1 Symbol Description Notes GND Ground 1 2 CML-I Tx2n Transmitter Inverted Data Input 3 CML-I Tx2p Transmitter Non-Inverted Data Input GND Ground 4 5 CML-I Tx4n Transmitter Inverted Data Input 6 CML-I Tx4p Transmitter Non-Inverted Data Input GND Ground 7 8 LVTTL-I ModSelL Module Select 9 LVTTL-I ResetL Module Reset Vcc Rx +3.
PAGE 5
35 GND Ground 36 CML-I Tx1p Transmitter Non-Inverted Data Input 37 CML-I Tx1n Transmitter Inverted Data Input GND Ground 38 1 1 Note: 1. GND is the symbol for signal and supply (power) common for the QSFP module. All are common within the QSFP module and all module voltages are referenced to this potential unless otherwise noted. Connect these directly to the host board signal-common ground plane. 2.
PAGE 6
Block Diagram 200G QSFP56 Module Tx1 Tx2 Tx3 Tx4 4 channels Driver + CDR Rx1 Rx2 Rx3 Rx4 4 channels TIA + CDR I2C 2×50G 4×50G VCSEL×4 2×50G 2×50G 4×50G PD×4 2×50G MCU 100G QSFP56 Module Tx1 Tx2 2 channels Driver + CDR Rx1 Rx2 2 channels TIA + CDR I2C www.addonnetworks.com 2×50G VCSEL×2 2×50G PD×2 2×50G 2×50G MCU Phone: 877.292.
PAGE 7
Mechanical Specification www.addonnetworks.com Phone: 877.292.
PAGE 8
About AddOn Networks In 1999, AddOn Networks entered the market with a single product. Our founders fulfilled a severe shortage for compatible, cost-effective optical transceivers that compete at the same performance levels as leading OEM manufacturers. Adhering to the idea of redefining service and product quality not previously had in the fiber optic networking industry, AddOn invested resources in solution design, production, fulfillment, and global support.