Addonics T E C H N O L O G I E S Jupiter Cipher Combo Hard Drive For the following models: JCCHDIU64, JCCHDIF64, JCCHDIS64 JCCHDIU128, JCCHDIF128, JCCHDIS128 User’s Guide Version 1.
FCC Warning Statement This equipment has been tested and found to comply with the limits for a class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the in structions, it may cause harmful interference to radio communications.
Contents FCC Warning ................................................................................... 1 Limited Warranty ............................................................................ 1 Contents............................................................................................ 2 Chapter 1 General Information ......................................................... 3 Features............................................................................
Chapter 1 General Information The Addonics Technologies Jupiter Cipher Combo Hard Drive is a portable 2.5” Hard Disk Drive kit. It consists of the Jupiter Cipher ExDrive and IDE drive cradle.
Jupiter Cipher Combo Hard Drive Item Number JCCHDIU64 JCCHDIF64 JCCHDIS64 JCCHDIU128 JCCHDIF128 JCCHDIS128 Product Description Jupiter Cipher 64-bit Combo Hard Drive USB 2.0 for 2.5” IDE hard drive Jupiter Cipher 64-bit Combo Hard Drive Firewire/iLink for 2.5” IDE hard drive Jupiter Cipher 64-bit Combo Hard Drive SATA for 2.5” IDE hard drive Jupiter Cipher 128-bit Combo Hard Drive USB 2.0 for 2.5” IDE hard drive Jupiter Cipher 128-bit Combo Hard Drive Firewire/iLink for 2.
Chapter 2 Jupiter Cipher Combo Hard Drive key Check to make sure you have the correct version of Jupiter Cipher Combo Hard Drive key. The key should match the label at the bottom of the drive enclosure. Yellow label DES-64 stands for Jupiter Cipher Combo Hard Drive 64-bit key Green label TDES-128 stands for Jupiter Cipher Combo Hard Drive 128-bit key IMPORTANT There is no back door for the Jupiter Cipher Combo Hard Drive encrypted hard drive if the key is lost or stolen.
Chapter 3 Keeping track of the hard drive If you are using the Jupiter Cipher Combo Hard Drive enclosure to encrypt multiple hard drives, it is important to label your hard drive if you are taking the drive out of the enclosure. The hard drive with Jupiter Cipher Combo Hard Drive encryption will look like a brand new drive when attach directly to the IDE or SATA controller of a computer. There will be no partition or any hint to indicate that the drive contains encrypted data.
Chapter 4 Jumper Settings Inside the Jupiter Cipher Combo Hard Drive Settings when Jupiter ExDrive is used as an External Enclosure 1. If the Jupiter ExDrive will be used externally with the external AC adapter, the switch from the case must be switch to the right, labeled EXT to grab power from external power supply. Application: Jupiter ExDrive can be set to receive power EXT and be used with all three types of USIB cables: USB2.0 USIB, Firewire USIB & SATA USIB 2.
Chapter 5 Hardware Installation Guide Exploded View of Enclosure shown with various components top cover 2.5” hard drive shock absorbers switch PCB bottom cover screw cipher slot Step 1 Separate the top from the bottom cover of the drive enclosure by loosening the screw as shown on the photo. Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.
Step 2 Align the male IDE connector on the 2.5” hard drive with the female IDE connector on the PCB. Push the hard drive till the connector pins on the hard drive is fully seated inside the connector on the PCB. Step 3 Wrap the shock absorber around the hard drive and PCB. Step 4 Turn over the PCB and secure the hard drive to the PCB with the mounting screws that come with the kit. Step 5 Mount the board to the bottom cover. Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.
Step 6 Put the top cover on by holding it in near vertical position and sliding th e two metal clips inside the two small slots on the rear of the bottom cover. Step 7 Lower the front of the top cover and making sure the two covers lined up properly. Tighten the small retaining screw on the front of the bottom cover to close the enclosure. Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.
Jupiter Cipher Combo Hard Drive Note: Combo hard drive is the combination of Jupiter Cipher ExDrive kit and the IDE drive cradle. Allows a 2.5” Jupiter Cipher ExDrive to be used as an external hard drive and also be plug-in to a desktop computer internally. You may use an available 3.5” Floppy bay like the image shown below to install the Jupiter Cipher ExDrive cradle. If none is available you can mount one to a 5.25 bay with mounting brackets to fit the bay.
Jupiter Cipher ExDrive is used as an Internal Enclosure Power Socket 40 Pin IDE Connector MC-36 Pin Connector Note: Use the jumper settings on the next page for the above configuration Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.
Configuration: Jupiter Cipher ExDrive enclosure is placed inside IDE drive cardle. IDE drive cradle is connected to the IDE Controller on the mainboard with an IDE cable. A.
Optional Hardware A. SATA Cartridge Cradle System 4-pin Molex power connector for PC power supply 2-pin connector on the PCB board SATA connector IDE to SATA converter 2-pin connector on the IDE to SATA converter board For Win98SE, Me, 2000 and XP Note: There are no drivers needed to use the Serial ATA cable as long as the drivers are installed for the Serial ATA Controller card/chip. It is plug and play.
Jumper Settings for Internal Cartridge Cradle System Jupiter Cipher ExDrive is set to MASTER Hard Drive Brand Hitachi NEC Fujitsu Toshiba Seagate Hard Drive Setting Master J4 Jumper Setting Pin 1~6 Open J1 Jumper Setting Pin 1 – Pin 3 Short Pin 2 – Pin 4 Short Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.
Chapter 6 Attaching USIB interface cable USIB connector for use with the Addonics USIB interface cable External power input jack (for use as external hard drive) Addonics USIB interface cable Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.
Chapter 7 7.1 USB2.0 USIB Cable (Model: AAUSBC-309) Note: USB Jupiter ExDrive is Plug and Play under Windows XP, 2000 and 98Me. There is no third party driver needed. • • Since USB 2.0 Hi-Speed is an evolution of the existing USB 1.1 specification, it is fully forward and backward compatible with current USB systems. If you do not have an USB2.0 port, you may install an optional USB2.0 adapter or controller Driver Installation for Win98 and Win98SE Downloading the USB2.
Driver Installation for Win98 and Win98SE 1. Make sure your computer is up and running. 2. Insert the USB2.0 USIB cable to the USB Port. 3. A "New Hardware Found" message shall pop up, click Next. 4. “What do you want Windows to do?” message opens. Select “Search for the best driver for your device,” click Next. 5. “Specify Location” message opens. Point to the location of C:\mass_storage_601where you unzip the files for the driver. Click Next. 6.
7.2 SATA USIB Cable (Model: AASAC-605) For Win98SE, Me, 2000 and XP Note: There no drivers needed to use the Serial ATA cable as long as the drivers are installed for the Serial ATA Controller card/chip. It is plug and play. Disk Management for Windows 98 Note: Refer to the SATARAID Management Utility Manual SATARAID Manual V1.30 (for non-RAID5 Controllers) found in the Addonics Technologies website Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.
7.3 FIREWIRE USIB Cable (Model: AAFWC-406) Note: Firewire Jupiter ExDrive is Plug and Play under Windows XP, 2000 and 98Me. There is no third party driver needed. Driver Installation for Win98 and Win98SE After plugging in the cable some system might prompt you for Win98SE CD, in case you don’t have The Win98SE CD and the wizard prompt you for: NTMAP.SYS please type C:\WINDOWS\SYSTEM32\DRIVERS NTMAPHLP.PDR please type C:\WINDOWS\SYSTEM\IOSUBSYS Reboot your system. Disk Management for Window 98 1. 2. 3.
For Windows 2000 & XP Operating Systems How to use Disk Management To start Disk Management: 1. Log on as administrator or as a member of the Administrators group. 2. Click Start, click Run, type compmgmt.msc, and then click OK. In the console tree, click Disk Management. The Disk Management window appears. Your disks and volumes appear in a graphical view and list view. 3.
7. Confirm that the options that selected are correct, and then click Finish. The new partition or logical drive is created and appears in the appropriate basic disk in the Disk Management window. If you chose to format the volume in step 6, the format process now starts. How to format a basic volume To format a partition, logical drive or basic volume: 1. In the Disk Management window, right-click the partition or logical drive that you want to format (or reformat), and then click Format. 2.
Technical Support If you need assistance to get your unit functioning properly, please call Addonics Technical Support. Our technical staff will be happy to assist you, but they will need your help to do so. Calling the technical support staff without all the proper information can be both time consuming and frustrating. Here are some tips to help you out: (1) (2) (3) (4) MODEL NUMBER – Please have this number on hand. SYSTEM INFORMATION – Type of computer, peripherals, etc.