Setup guide

5110XM-SIMP-V2
ADEMCO 5110XM SIMPLIFIED WIRING DIAGRAM
N.O.
N.C.
2k
N.O.
N.C.
N.O.
N.C.
2k
N.O.
N.C.
2k
2k
N.O.
N.C.
2k
12
9
10
11
13 19
2017 1815 1614
The combined standby current drawn from aux power and relay power cannot exceed 350mA. The combined alarm current drawn from aux power, relay power, and bell cannot exceed 1.0A.
TROUBLE
(YELLOW)
ALARM
(RED)
SUPERVISORY
(YELLOW)
SILENCE
(YELLOW)
LINE FAULT
(YELLOW)
COMM FAIL
(YELLOW)
RED
BLACK
GREEN
ZONE 1 + ZONE 2 +
ZONE 1/ZONE 2 -
ZONE 3 + ZONE 4 +
ZONE 3/ZONE 4 -
ZONE 5 +
ZONE 5 -
YELLOW
+
GND
DATA IN
2-WIRE SMOKE DETECTOR LOOP
DATA OUT
BATT TROUBLE
(YELLOW)
AC POWER
(GREEN)
MAIN
DIALER
LINE
SEIZE
(GREEN)
WARNING
SOUNDER ACTIVATES ON ALARMS,
SUPERVISORIES AND TROUBLES
SOUNDER SILENCE SWITCH
PUSH ONCE TO SILENCE,
PUSH AGAIN TO RESET
2k MODEL EOLR20
HORN
BELL
LED INDICATOR BOARD PLUG BOARD INTO THE J5 9-PIN HEADER.
J5
24 5232221 786
FIRE CKTS: Supervise using 2k EOLR. Use polarized sounding devices.
Ratings: 10 - 14VDC, 1.0A max. See note 1, see instructions for compatible devices.
120VAC, 60Hz
CONNECT TO
A DEDICATED
CIRCUIT
CONNECT TO
PROPER EARTH
GROUND.
WHT
BLK
BLUE
BLUE
NOTE: USE WIRES RATED FOR 90C OR HIGHER.
18VAC, 40VA
CONNECT TO AC POWER TERMINALS 1, 2
MAINTAIN MINIMUM 1/4" SPACING FROM OTHER WIRING.
(NOTE 6)
GREEN
2A CIRCUIT
BREAKER
ALL CIRCUITS ARE POWER LIMITED EXCEPT THE OUTPUT OF THE POWER TRANSFORMER AND BACKUP BATTERIES ALL POWER-LIMITED WIRING MUST BE SEPARATED FROM OTHER WIRING BY AT LEAST 1/4 INCH (6.4.MM). AUX RELAY HAS PROGRAMMABLE FUNCTION (NOT SUPERVISED) JUMPER W3 INT ACT: 10-14VDC ON TERMINAL 6 350mA MAX (STANDBY) /1A MAX (ALARM), POWER-LIMITED (SEE NOTE 2). USE TERMINAL 18 FOR GROUND RETURN. JUMPER W3 CUT: NO VOLTAGE ON TERMINAL 6. RELAY CONTACT RATING: 30 VAC/VDC, 2A MAX RESISTIVE LOADS.
POLE/RELAY +
N.C.
GREEN
N.O.
AC Input Power
AC AC
RJ31X
MAKE CONNECTIONS TO SEPARATE TELEPHONE LINES USING CABLE SUPPLIED. SUPERVISION IS PROGRAMMABLE.
USE BATTERY CABLES SUPPLIED 12V LEAD ACID BATTERY 7 AH MIN/14 MAX. SEE INSTRUCTIONS FOR REQUIRED CAPACITY AND BATTERY MOUNTING
BACK-UP
DIALER
LINE
SEIZE
(GREEN)
MAIN DIALER
PHONE JACK
BACK-UP DIALER
PHONE JACK
BATT +
ZONE NOTES
BATT -
BLACK
RED
ALL ZONES ARE CLASS B AND PROVIDE STYLE B SUPERVISION. ZONE RESISTANCE (EXCLUDING EOLR): +ZONES 1-4: 300 OHM MAX. +ZONE 5: 100 OHM MAX. ZONE RESPONSE: 300-500 MILLISECOND (ALL ZONES). ZONE 5 RATINGS: +10-14VDC +2mA MAX FOR 2-WIRE SMOKE DETECTORS. UP TO 16 DETECTORS OF TYPE SPECIFIED IN INSTRUCTIONS MAY BE USED. 2K EOLR IS ADEMCO MODEL EOL20. PROGRAM USING DELAY TIME MARKED ON DETECTORS.
EARTH GROUND
RELAY POWER JUMPER
AUXILIARY
RELAY
BELL +
BELL CIRCUIT SUPERVISION JUMPER INTACT: SUPERVISED USING 2K EOLR DO NOT CUT.
BELL -
BLUE BLUE
TO FACILITY GROUND TO POWER SUPPLY ENCLOSURE TO PC BOARD TERMINAL 8 TO CABINET DOOR (NOT SHOWN)
SEE AC
TRANSFORMER
CONNECTIONS
ABOVE
(SUPERVISED)
For commercial fire, bell timeout must be a minimum of 6 minutes.
All Earth Grounds must be wired to cabinet ground post. Use minimum AWG16 wire.
Each output may be selected for Style Y supervision or no supervision. Supervision may be disabled by cutting jumper W2 and programming Zone 6 for no response. For approved Special Application Notification Appliance Circuits, the maximum line impedance allowed when the system is fully loaded to 1.0A for devices that can operate at a minimum of 8VDC is 2.0 ohms. For devices that can operate at a minimum of 9VDC the maximum line impedance is 1.0 ohms. 2k EOLR is Ademco model EOL20.
1.
6.
No more than one (1) wire per terminal may be connected.
5.
Use only 14-22 AWG wire.
4.
3.
2.
NOTES
W3
(RED)
W2 (WHITE)
OPTIONAL
REMOTE
KEYPADS
AUX POWER RATING: 10-14VDC, 350mA MAX, POWER LIMITED NOT SUPERVISED (SEE NOTE 2). 6150 OR 6160 MAY BE USED IN CONJUNCTION WITH THE CONTROL PANEL'S LED INDICATORS AND SILENCE/RESET BUTTON. ONLY A 6160 MAY BE USED TO PROGRAM PANEL.
CABINET GROUND POST
EARTH GROUND INFORMATION
(SEE NOTE 6)
(NOTE 6)
RJ31X
AUX POWER
REFER TO SOC LABEL FOR DETAILED INFORMATION