Setup guide

ManualsBrandsADEMCO ManualsHome building and DecorLYNXR

K14117 3/06 Rev. A

ADEMCO LYNXR-I

Security Systems

Quick Start Guide

LYNXR-I is not intended for UL985 Household Fire applications unless a 24-hour backup battery (P/N

LYNXRCHKIT-HC or LYNXRCHKIT-SHA) is installed.

Introduction

This Quick Start Guide can help you install the rechargeable LYNXR-I quickly and easily by providing the basic

steps for installation using the built-in defaults. For more detailed information and important notes, refer to the

LYNXR-I Installation and Setup Guide.

The following steps assume that one of the system’s default tables will be used.

For programming data values and Powerline Carrier Devices other than those listed in the default tables, see the

Installation Instructions.

Default Table Summary

Zone Table 1 Table 2 Table 3 Table 4

2 front door front door front door front door

3 back door back door back door back door

4 window garage door window window

5 motion detector motion detector window window

6 ------- smoke detector window window

7 ------- ------- window window

8 ------- ------- motion detector motion detector

9 ------- ------- smoke detector smoke detector

26 loop 3 arm away loop 3 arm away loop 3 arm away loop 3 arm away

27 loop 2 disarm loop 2 disarm loop 2 disarm loop 2 disarm

28 loop 4 arm stay loop 4 arm stay loop 4 close device loop 4 close device

29 loop 1 no alarm response loop 1 no alarm response loop 1 no alarm response loop 1 no alarm response

30 loop 3 arm away loop 3 arm away loop 3 arm away loop 3 arm away

31 loop 2 disarm loop 2 disarm loop 2 disarm loop 2 disarm

32 loop 4 arm stay loop 4 arm stay loop 4 close device loop 4 close device

33 loop 1 no alarm response loop 1 no alarm response loop 1 no alarm response loop 1 no alarm response

92 duress duress duress duress

99 silent alarm audible alarm silent alarm silent alarm

Master User Code 1-2-3-4 1-2-3-4 1-2-3-4 1-2-3-4

Installer Code 4-1-1-2 4-1-1-2 4-1-1-2 4-1-1-2

Duress Code ------ ------ ------ ------

Entering Expert Program Mode: installer code + 8 0 0

Interactive Mode Used to Program

56 Enhanced Zone Programming Zone characteristics, report codes, and serial numbers

83 Enhanced Sequential Mode 5800 Series transmitter serial numbers

*84 Assign Zone Voice Descriptors Voice descriptors for each zone

Exiting Program Mode:

98 inhibits re-entry into the Programming mode using the Installer Code.

99 allows re-entry into the Program mode using Installer Code + 8 0 0.

NOTES: • Table 4 supports the automatic paging feature (open/close events reported to pager phone number),and a Powerline Carrier Device programmed

as device 8, which closes and stays closed upon burglary alarms and restores after bell timeout. For other applications or actions (e.g., using a

pulsing siren), see the *80 Device Programming Menu Mode section of the Installation Instructions.

• Primary and secondary report format for all tables is Ademco’s Contact ID® reporting.

• Tables 1, 3 and 4 record only alarms, alarm restores, troubles, and trouble restores in the event log. Table 2 records all events in the event log.

Summary of content (8 pages)

PAGE 1
K14117 3/06 Rev. A ADEMCO LYNXR-I Security Systems Quick Start Guide UL LYNXR-I is not intended for UL985 Household Fire applications unless a 24-hour backup battery (P/N LYNXRCHKIT-HC or LYNXRCHKIT-SHA) is installed. Introduction This Quick Start Guide can help you install the rechargeable LYNXR-I quickly and easily by providing the basic steps for installation using the built-in defaults. For more detailed information and important notes, refer to the LYNXR-I Installation and Setup Guide.
PAGE 2
Installing LYNXR-I Installation and Electrical Connections Step 1. 2. 3. Action Install the control as follows: a. Separate the front assembly from the back plate and disconnect the cable from the front assembly board. Note: Disconnect the cable only from the front assembly board, not from the terminal block PC board. b. Mount the back plate. Make wiring connections as follows: a. Connect the incoming phone line to either the 8-position jack or terminals 2 (TIP) and 3 (RING). b.
PAGE 3
UL NOTE THE MINIMUM WIRE SIZE USED FOR TELEPHONE INSTALLATIONS MUST BE #26 GAUGE INCOMING PHONE LINE EARTH GROUND 8 POS JACK 1 FUTURE USE PHONE 2 3 4 5 6 8 7 ( ) TIP RING TIP RING GND DATA IN WARNING: TO PREVENT RISK OF SHOCK DISCONNECT TELEPHONE LINE AT TELECOM JACK BEFORE SERVICING THIS UNIT. GND SOUNDERS 9 10 11 12 ( ) (+) ( ) (+) PLCD 13 14 AC 15 16 DATA SYNC OUT IN POWERLINE CARRIER DEVICES RJ11 ALL OUTPUT CIRCUITS ARE POWER LIMITED.
PAGE 4
Step 3. Action Enhanced Sequential Mode - Press *83, then follow the prompts as follows: Zone Number - Enter 2-digit zone number of the first transmitter to have its serial number entered. The system will announce the Voice Descriptor for the selected zone number, if it is programmed. Press [*] to continue. Starting with this zone, the system will search for the first transmitter, which has all of the following attributes pre-programmed in Zone Programming.
PAGE 5
Step 3. Action Once all 7 digits have been entered, press the [*] key. If less than 7 digits are entered, (Cont.) the keypad will emit a single long beep and return to the (1A) prompt without displaying the “L”. If more than 7 digits have been entered, the first 6 digits will be saved along with the last digit that was entered (entering 123456789 yields the serial number 1234569). Note: If 52 seconds passes and no entry has been made, the system returns to prompt (1A). 3) d.
PAGE 6
Keypad Functions (when default programming is used) Security Functions Checking system status: STATUS (high level messages); press STATUS again for secondary messages. To arm in STAY mode: Press and hold down STAY (or enter your code + STAY ) See note below. To restart exit delay: STAY (applies only if system is armed in Stay mode and Quick Exit option has been enabled) To arm in AWAY mode: Press and hold down AWAY (or enter your code + AWAY ) See note below.
PAGE 7
Remote Phone Control Operation To remotely disarm system: + [1] + [2] To remotely arm in AWAY mode: To remotely arm in STAY mode: + [3] + [2] or [3] + [0] To remotely arm in AWAY or STAY with NO DELAY: To remotely activate X10 devices 1-6: [#] + [4] + device no. + [#] + [4] + device no. To remotely activate X10 devices 7 & 8: To remotely deactivate X10 devices 1-6: [#] + [7] + device no. + [#] + [7] + device no. To remotely deactivate X10 devices 7 & 8: To remotely bypass a zone: + [6] + zone no.