Nuscan 3000 Laser Barcode Scanner Programming Manual
FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause harmful interference to radio communications.
Table of Contents 1. 2. 3. 4. 5. INTRODUCTION………………………………………………………………………………..………2 INSTALLATION………………………………………………………………………………..….......4 USB Connection…………………………………………………………………………………5 PS2(K/B) Connection………………………………………………………………………….5 RS232 Connection………………………………………………………………………………6 SET UP FROM BAR CODE LABEL…………………………………………………………..……..7 Multi-interface Functions…………………………………………………………………….8 Interface-KBW………………………………………………………………………………….
Introduction 2
Laser barcode scanner combines the best scanning performance and value. The device provides an accurate, easy, and fast method of data entry and data storage for computerized information systems. It is easy to install and does not require software or drivers to operate. The products we are offering can be integrated into a computer system by RS232, PS2 or USB interface.
Installation 4
Insert the plug on the free end of the Communications Cable into the appropriate connector on the host as below described: 1. USB Connection connect with host 2.
3. RS232 Connection connect with host require adapter for power supply NOTE: for Serial port (RS232 cable), please plug the power connector of 5V power adapter to RS232 cable. 1. Be sure that Host computer is turned on. 2. Ensure that all connections are secure. 3. Turn on your host. And please operate the scanner under the right software application. 4. Aim the scanner at a barcode, ensure that the scanner is in trigger mode (default), and press the trigger. 5.
Setup from Bar Code Label 7
Multi-Interface Functions – 1 OUTPUT FIRMWARE VERSION RESET CONFIGURATION TO DEFAULTS 0A OUTPUT MODE – KEYBOARD WEDGE 0B OUTPUT MODE 000600 GOOD READ BEEP TONE – NONE 000601 BUZZER / LED 014200 DECODE OPTIONS REVERSE IMAGE – ENABLE GOOD READ BEEP TONE - RESET 0B142 IMAGE 01391 DECODE OPTIONS SEND BAR CODE ID DISABLE OUTPUT MODE - SERIAL DECODE OPTIONS REVERSE IMANGE - DISABLE 01390 CODE ID DECODE OPTIONS SEND BAR CODE ID – AS A PREFIX 01400 01401 DECODE OPTIONS SEND BAR CODE ID RESET DE
Multi-Interface Functions – 2 SCAN MODE – SINGLE SCAN READING MODE SCAN MODE – SINGLE SCAN NO TRIGGER 013300 013301 SCAN MODE – MULTISCAN SCAN MODE – MULTISCAN NO TRIGGER 013302 013303 SCAN MODE – CONTINUOUS SCAN SCAN MODE - PULSE 013304 013305 LASER/CCD TIMEOUT – 5 SECONDS LASER/CCD TIMEOUT – 2 SECONDS 0134005 0134002 LASER/CCD PULSE RATE - 7 LASER/CCD PULSE RATE - 3 013507 013503 9
Interface – KBW WEDGE MODE - AUTODETECT PC Communication 000200 TRANSMIT SPEED - 0 WEDGE MODE – SCAN SET 2 PASS THRU 000204 TRANSMIT SPEED 0000000 TRANSMIT SPEED - 25 0000025 LANGUAGE KEYBOARD COUNTRY - USA KEYBOARD COUNTRY - GERMAN 0005000 0005010 KEYBOARD COUNTRY - UNIVERSAL KEYBOARD COUNTRY – FRANCE 0005009 0005025 10
Interface – Serial - 1 BAUD RATE SERIAL BAUD RATE - 2400 SERIAL BAUD RATE - 4800 000703 000704 SERIAL BAUD RATE - 9600 SERIAL BAUD RATE - 19200 000705 000706 SERIAL HANDSHAKE - NONE HAND SHAKE 001200 SERIAL HANDSHAKE – XON/XOFF 001201 SERIAL HANDSHAKE – ACK/NAK SERIAL HANDSHAKE – RTS/CTS 001202 001203 SERIAL HANDSHAKE TIMEOUT – 2 SECONDS SERIAL HANDSHAKE TIMEOUT – 5 SECONDS 0013020 0013050 11
Interface – Serial - 2 PARAMETERS SERIAL DATA BITS - 8 SERIAL DATA BITS - 7 00081 00080 SERIAL STOP BITS - 1 SERIAL STOP BITS - 2 00090 00091 SERIAL PARITY - NONE SERIAL PARITY - ODD 001000 001001 SERIAL PARITY - MARK SERIAL PARITY - EVEN 001002 001003 SERIAL PARITY - SPACE SERIAL PARITY - RESET 001004 0B010 12
Symbologies On/Off - 1 CODE 11 - ENABLE CODE 11 01261 CODE 39 ENABLE CODE 11 - DISABLE 01260 CODE 39 00221 CODE 39 DISABLE 00220 FULL ASCII ENABLE FULL ASCII DISABLE 00231 00230 13
Symbologies On/Off - 2 CODE 93 CODE 93 - ENABLE CODE 93 - DISABLE 00620 00621 CODE 128 - ENABLE CODE 128 CODE 128 - DISABLE 00691 00690 CODE 128 ISBT - ENABLE CODE 128 ISBT - DISABLE 00701 00700 CODABAR - ENABLE CODABAR 00850 00851 I2OF5 - ENABLE INTERLEAVED 2 OF 5 00961 ID2OF5 - ENABLE CODABAR - DISABLE I2OF5 - DISABLE 00960 INDUSTRIAL 2 OF 5 ID2OF5 - DISABLE 01060 01061 14
Symbologies On/Off - 3 MSI MSI - ENABLE MSI - DISABLE 01151 01150 UPC-A ENABLE UPC/EAN UPC-A DISABLE 00341 00340 UPC-E ENABLE UPC-E DISABLE 00351 00350 EAN-13 ENABLE EAN-13 DISABLE 00361 00360 EAN-8 ENABLE EAN-8 DISABLE 00371 00370 15
Symbologies Set Up - 1 CODE 11 CODE 11 ID CHARACTER – “m” CODE 11 ID CHARACTER – “Z” 0131m 0131Z CODE 11 LASER/CCD REDUNDANCY ENABLE CODE 11 LASER/CCD REDUNDANCY DISABLE 01321 CODE 39 SS CHAR - NONE 01320 CODE 39 CODE 39 SS CHAR ‛+’ 002700 002704 CODE 39 SEND START/STOP CHARS ENABLE CODE 39 SEND START/STOP CHARS DISABLE 00281 00280 CODE 39 ID CHARACTER ‛a’ CODE 39 ID CHARACTER ‛z’ 0031a 0031Z CODE 39 LASER/CCD REDUNDANCY ENABLE CODE 39 LASER/CCD REDUNDANCY DISABLE 00331 00330 16
Symbologies Set Up – 2 CODE 93 CODE 93 ID CHARACTER – “h” CODE 93 ID CHARACTER – “Z” 0066h 0066Z CODE 93 LASER/CCD REDUNDANCY ENABLE CODE 93 LASER/CCD REDUNDANCY DISABLE 00681 CODE 128 ID CHARACTER – ‛g’ 00680 CODE 128 CODE128 ID CHARACTER - ‛Z’ 0081g 0081Z CODE 128 LASER/CCD REDUNDANCY ENABLE CODE 128 LASER/CCD REDUNDANCY DISABLE 00841 CODABAR SEND START/STOP CHARS ENABLE 00840 CODABAR CODABAR SEND START/STOP CHARS DISABLE 00861 00860 CODABAR WIDE GAPS ALLOWED ENABLE CODABAR WIDE GAPS
Symbologies Set Up – 3 CODABAR CODABAR ID CHARACTER –‛k’ CODABAR ID CHARACTER –‛Z’ 0094k 0094Z CODABAR LASER/CCD REDUNDANCY - ENABLE CODABAR LASER/CCD REDUNDANCY - DISABLE 00951 I2OF5 ID CHARACTER – ‛i’ 00950 Interleaved 2 of 5 I2OF5 ID CHARACTER – ‛Z’ 0104i 0104Z I2OF5 LASER/CCD REDUNDANCY ENABLE I2OF5 LASER/CCD REDUNDANCY DISABLE 01051 ID2OF5 ID CHARACTER - ‛j’ 01050 Industrial 2 of 5 ID2OF5 ID CHARACTER - ‛Z’ 0113j 0113Z ID2OF5 LASER/CCD REDUNDANCY ENABLE ID2OF5 LASER/CCD REDUNDANCY
Symbologies Set Up – 4 MSI MSI ISBN ID CHARACTER –‛f’ MSI ISBN ID CHARACTER –‛Z’ 0053f 0053Z MSI LASER/CCD REDUNDANCY ENABLE MSI LASER/CCD REDUNDANCY DISABLE 01251 EXPAND UPC-E TO UPC-A ENABLE 01250 UPC/EAN EXPAND UPC-E TO UPC-A DISABLE 00381 00380 EXPAND UPC-A TO EAN-13 ENABLE EXPAND UPC-A TO EAN-13 DISABLE 00391 00390 CONVERT EAN-13 TO ISBN ENABLE CONVERT EAN-13 TO ISBN DISABLE 00481 00480 UPC-A ID CHARACTER ‛b’ UPC-A ID CHARACTER ‛Z’ 0049b 0049Z 19
Symbologies Set Up – 5 UPC/EAN UPC-E ID CHARACTER ‛c’ UPC-E ID CHARACTER ‛Z’ 0050c 0050Z EAN-13 ID CHARACTER ‛e’ EAN-13 ID CHARACTER ‛Z’ 0051e 0051Z EAN-8 ID CHARACTER ‛d’ EAN-8 ID CHARACTER ‛Z’ 0052d 0052Z ISBN ID CHARACTER ‛f’ ISBN ID CHARACTER ‛Z’ 0053f 0053Z UPC/EAN SUPPLEMENTS - DISABLE UPC/EAN SUPPLEMENTS – 2 DIGIT ONLY 00550 00551 UPC/EAN SUPPLEMENTS – 5 DIGIT ONLY UPC/EAN SUPPLEMENTS – 2 & 5 DIGIT 00552 00553 20
Symbologies Set Up – 6 UPC/EAN UPC/EAN LASER/CCD REDUNDANCY UPC/EAN LASER/CCD REDUNDANCY ENABLE DISABLE 00541 00540 21
EDIT SETUP BAR CODES EDIT #1 – STRIP 1 LEADING CHARACTER EDIT #1 - OFF ON ALL BAR CODES THAT START WITH ‛12345’ 02000101000000100000000112345 0B20001 EDIT #2 – STRIP 1 TRAILING CHARACTER EDIT #2 – OFF 020002020000001 0B20002 EDIT #1 – FILTER LEADING SPACES EDIT #1 - OFF 020001030000032 0B20001 EDIT #1 – FILTER TRAILING SPACES EDIT #1 - OFF 020001040000032 0B20001 EDIT – FILTER ALL ‛-’ CHARACTERS EDIT – DISABLE FILTER OF ALL ‛-’ CHARS 020000050000045 0B20000050000045 EDIT - INSERT LEADI
MACRO/SPECIAL KEYS SETUP BAR CODES MACRO #1 – FIND ‛1’ AND REPLACE WITH MACRO #1 - DISABLED ‛ONE’ 02010101011ONE 0B20101 MACRO #2 – FIND ‛2’ AND REPLACE WITH ‛TWO’ FOR CODE 39 ONLY MACRO #2 - DISABLED 0201023012TWO 0B20102 MACRO – FIND ‛0’ AND REPLACE WITH ‛A’ MACRO – FIND ‛0’ AND REPLACE WITH ‛A’ DISABLE 02010001010A 0B2010001010A SPECIAL KEY –MAP F3 TO ‛0’ SPECIAL KEY – DISABLE F3 KEY MAPPING 0162048 0B162 SPECIAL KEY – MAP KEYPAD ENTER TO ‛2’ SPECIAL KEY – DISABLE KEYPAD ENTER MAPPING
TERMINATION STRING SETUP BAR CODES STRING #1 – TERMINATION CHAR - CR STRING #1 – TERMINATION - LF 0202011000$0D 0202011000$0A STRING #1 – TERMINATION CR+LF STRING #1 - DISABLE 0202011000$0D$0A 0B20201 STRING #2– CODE 128 TERMINATION CHAR CR STRING #2 – CODE 128 TERMINIATION CHAR LF 0202021080$0D 0202021090$0A STRING #2– CODE 128 TERMINATION CHAR – CR+LF STRING #2– CODE 128 TERMINATION CHAR REMOVED 0202021080$0D$0A 0B20202 STRING – CODE 39 TERMINATION CHAR TAB STRING – CODE 39 TERMINATION CH
Factory Default Setting 25
Scanner Timing Default RS-232 communication Default Baud rate 9600 Parity None Data Bits 8 Stop Bit 1 RTS/CTS Off Terminator Keyboard Wedge Communication Default Terminal Type PC/AT Keyboard US keyboard Terminator Enter (Alpha numeric) USB Communication Default Terminator type Enter Code mode Scan Code Keyboard US keyboard Decoder Selection Default EAN/UPC Enable Code 39 Enable Code 32 Disable CODABAR Enable ITF 2 of 5 Enable MSI Disable Code 93 Enable Co
Appendix-A Troubleshooting & Error Beeps 27
a. Problem: Nothing happens when I follow the operating instructions. Possible Cause Possible Solution Interface cables are loose Check for loose cable connections b. Problem: When I connected RS232 interface reader to PC, I could not get power up signal. Possible Cause Possible Solution There is no power from PC series Use external power supply or take the port. power from PC. c. Problem: When I connected RS232 interface reader to PC or terminal, I got power up signal but no data transmitted.
d. My computer gets a keyboard error while booting up. Possible Cause Possible Solution The scanner is damaged or is no Disconnect the scanner from your longer functioning. computer and use your keyboard only. Reboot your computer. If your computer still gets a keyboard error, then the problem may not be the scanner. Call technical support for assistance. e. Problem: Light comes on, but symbol does not decode.
f. Problem: The scanner beeps, but no data is displayed on my computer. Possible Cause Possible Solution Scanner is not programmed for the Please make sure the scanner is correct host type. configured to the appropriate host type by scanning the corresponding programming barcode on the User’s Manual.
h. Problem: Some of the barcode data is missing displayed on the host. Possible Cause Possible Solution The scanner’s transmit speed is too For RS232, you can set up the fast. scanner’s transmit speed. i. My Caps Lock LED on my keyboard flickers when I read a bar code. Possible Cause Possible Solution The Keyboard Country that you are This is normal operation.
32
