Barcode Scanner Model no.
FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause harmful interference to radio communications.
Table of Contents 1. INTRODUCTION………………………………………………………2~3 2. INSTALLATION…………………………………………………………4~6 3. SET UP FROM BAR CODE LABEL…………………………………….7 Operating Settings……………………………………………………….8 Sensor Mode……………………………………………………………8~9 USB Country Keyboard Types………………………………..10~11 1D Symbologies On/Off…………………………………………12~14 2D Symbologies On/Off…………………………………………15~16 Symbologies Set Up……………………………………………..17~23 Termination String Setup Bar Codes…………………………….
Introduction 2
NUSCAN 5000 barcode scanner, using 2D engine, combines the best scanning performance and value. The device provides an accurate, easy, and fast method of data entry and data storage for computerized information systems. It is easy to install drivers to operate. All the operating parameters are programmed by bar code programming menu and stored in non-volatile RAM which can retain the settings after power is turned off.
Installation Insert the plug on the free end of the Communications Cable into the appropriate connector on the PC as below described: USB cable Connection(USB HID): Reset Configuration to Defaults If you are unsure of the scanner configuration or have scanned the incorrect codes, please scan the “Reset Configuration to Defaults” barcode below. This will reset the scanner to its factory defaults settings in USB interface. 1. Be sure that PC is turned OFF 2. Connect scanner cable to the USB port on the PC.
Reset Configuration to Defaults If you are unsure of the scanner configuration or have scanned the incorrect codes, please scan the “Reset Configuration to Defaults” barcode. This will reset the scanner to its factory defaults settings.
Operation Tip Do not hold the scanner directly over a barcode at 90˚. Scanning light bounces directly back into the scanner from the barcode label is known as specular reflection which will create a "dead zone" where decoding is difficult. Practice a few times to find what range of angles works best. Maintenance Cleaning the scan window is the only maintenance required. A dirty window may affect scanning accuracy.
Setup from Bar Code Label 7
** Code Programming ON (Pro CMD : 0006010) ** Code Programming OFF (Pro CMD : 0006000) Operating settings Trigger Mode Auto-Sensing Pro CMD : 0302000 Pro CMD : 0302010 Sensor Mode Timeout Sensor Mode High Sensitivity (= 8) Pro CMD : 0313000 Pro CMD : 0312020 Normal Sensitivity (= 11) Low Sensitivity (= 14) Pro CMD : 0312010 Pro CMD : 0312000 Enhanced Sensitivity (= 5) Pro CMD : 0312030 8
** Code Programming ON (Pro CMD : 0006010) ** Code Programming OFF (Pro CMD : 0006000) Prohibit Reading All = allow reading programming codes only.
USB Country Keyboard Types The keyboard arrangements and country codes vary in different countries. Refer country codes to the table “USB Country Keyboard Types”. Follow the steps mentioned below to program. 1. “Code Programming ON” 2. “Select Country Code” 3. Read digit codes (according to country code) 4. “Save ” 5.
Digit Code It is must to be read save after read digit code.
** Code Programming ON (Pro CMD : 0006010) ** Code Programming OFF (Pro CMD : 0006000) 1D Symbologies On/Off – 1 CODE 39 CODE 39 ENABLE CODE 39 DISABLE Pro CMD : 0408020 Pro CMD : 0408010 ENABLE * Sign Pro CMD: 0408090 DISABLE * Sign CODE 93 Pro CMD: 0408080 CODE 93 - ENABLE CODE 93 - DISABLE Pro CMD : 0410020 Pro CMD : 0410010 CODE 128 - ENABLE CODE 128 Pro CMD : 0400020 CODABAR - ENABLE Pro CMD : 0409020 INTERLEAVED 25 ENABLE CODE 128 - DISABLE Pro CMD : 0400010 CODABAR CODABAR - DI
** Code Programming ON ** Code Programming OFF (Pro CMD : 0006000) (Pro CMD : 0006010) 1D Symbologies On/Off – 2 UPC-A ENABLE UPC/EAN UPC-A DISABLE Pro CMD : 0404020 Pro CMD : 0404010 UPC-E ENABLE UPC-E DISABLE Pro CMD : 0403020 EAN-8 ENABLE Pro CMD : 0403010 EAN-8 DISABLE Pro CMD : 0401020 EAN-13 ENABLE Pro CMD : 0401010 EAN-13 DISABLE Pro CMD : 0402020 EAN-128 ENABLE Pro CMD : 0402010 UCC/EAN Pro CMD : 0412020 ENABLE Pro CMD : 0412010 Industrial 25 Pro CMD: 0417020 ENABLE EAN-128 DISA
** Code Programming ON ** Code Programming OFF (Pro CMD : 0006010) (Pro CMD: 0006000) 1D Symbologies On/Off – 3 MSI Plessy ENABLE MSI Plessy Pro CMD : 0420020 Code 11 ENABLE Pro CMD : 0420010 Code 11 Pro CMD : 0415020 ISBN ENABLE Code 11 DISABLE Pro CMD : 0415010 ISBN Pro CMD : 0416020 ENABLE MSI Plessy DISABLE ISBN DISABLE Pro CMD : 0416010 UCC/EAN Composite Pro CMD : 0414020 DISABLE Pro CMD : 0414010 14
** Code Programming ON (Pro CMD : 0006010) ** Code Programming OFF (Pro CMD : 0006000) 2D Symbologies On/Off - 1 Data Matrix -ENABLE Data Matrix Pro CMD : 0504020 Data Matrix -DISABLE Pro CMD : 0504010 **Forward Direction Both Barcode Only Pro CMD: 0504320 Pro CMD:0504322 Backward Direction Barcode Only Pro CMD : 0504321 QR Code -ENABLE Aztec -ENABLE QR Code Aztec Pro CMD : 0503020 QR Code -DISABLE Aztec -DISABLE Pro CMD : 0503010 15
** Code Programming ON (Pro CMD : 0006010) PDF 417ENABLE ** Code Programming OFF (Pro CMD : 0006000) PDF 417 Pro CMD : 0501020 PDF 417 DISABLE Pro CMD : 0501010 **Forward Direction Barcode Only Both Pro CMD:0501320 Pro CMD:0501322 Backward Direction Barcode Only Pro CMD:0501321 16
** Code Programming ON (Pro CMD : 0006010) ** Code Programming OFF (Pro CMD : 0006000) Symbologies Set Up - 1 TRANSMIT UCC/EAN-8 CHECK –ENABLE UPC/EAN -8 CHECK Digit Pro CMD : 0401040 TRANSMIT UCC/EAN-13 CHECK –ENABLE Pro CMD : 0401030 UPC/EAN -13 CHECK Digit Pro CMD : 0402040 Transmit 13 digits ISBN Transmit Transmit 10 digits Pro CMD : 0416040 UPC-E CHECK Digit Pro CMD : 0403040 TRANSMIT UPC-A CHECK –ENABLE TRANSMIT UCC/EAN-13 CHECK –DISABLE Pro CMD : 0402030 Pro CMD : 0416030 TRANSMIT UPC
** Code Programming ON (Pro CMD : 0006010) ** Code Programming OFF (Pro CMD : 0006000) Symbologies Set Up - 2 NO Check, Transmit All Interleaved 25 CHECK Digit Pro CMD : 0405050 Check, Transmit All Check, Transmit No Check Pro CMD : 0405060 Pro CMD : 0405070 NO Check, Transmit All Matrix 25 CHECK Digit Pro CMD : 0406050 Check, Transmit All Pro CMD : 0406070 Code 39 FULL ASCII -ENABLE Pro CMD : 0406060 CODE 39 FULL ASCII Pro CMD : 0408110 NO Check, Transmit All Check, Transmit No Check Code 39
** Code Programming ON (Pro CMD : 0006010) ** Code Programming OFF (Pro CMD : 0006000) Symbologies Set Up – 3 NO Check, Transmit All CODEBAR CHECK Digit Pro CMD : 0409050 Check, Transmit No Check Pro CMD : 0409060 Check, Transmit All Pro CMD : 0409070 Transmit Both Start & Stop Character Transmit Neither Start & Stop Character Pro CMD：0409090 Pro CMD：0409080 NO Check, Transmit All CODE 93 CHECK Digit Pro CMD : 0410050 Check, Transmit No Check Pro CMD : 0410060 Check, Transmit All Pro CMD
** Code Programming ON (Pro CMD : 0006010) ** Code Programming OFF (Pro CMD : 0006000) Symbologies Set Up - 4 NO Check, Transmit All MSI Plessy CHECK Digit Double Check Digits, MOD10/MOD11 Pro CMD : 0420050 Single Check Digit，MOD10 Pro CMD : 0420080 NO Transmit Check Digits Pro CMD : 0420060 Double Check Digits， MOD10/MOD10 Pro CMD : 0420090 Transmit Check Digits Pro CMD : 0420070 Pro CMD : 0420100 20
** Code Programming ON (Pro CMD : 0006010) ** Code Programming OFF (Pro CMD : 0006000) Symbologies Set Up - 5 NO Check, Transmit All Code 11 CHECK Digit Single Check Digit MOD11（Len <= 10) Double Check Digits MOD11/MOD11 （Len > 10) Pro CMD : 0415050 Pro CMD : 0415090 Single Check Digit，MOD11 Single Check Digit MOD11（Len <= 10) Double Check Digits MOD11/MOD9 (Len > 10) Pro CMD : 0415060 Pro CMD : 0415100 Double Check Digits， MOD10/MOD10 Do not Transmit Check Digits Pro CMD : 0415070 Pro CMD :
** Code Programming ON (Pro CMD : 0006010) ** Code Programming OFF (Pro CMD : 0006000) Symbologies Set Up – 6 UPC/EAN FORMATIN EXPAND EAN-8 TO EAN-13 G ENABLE Pro CMD : 0401100 2 Digits Addenda ENABLE EXPAND EAN-8 TO EAN-13 DISABLE Pro CMD : 0401090 UPC/EAN-8 Addenda Code 2 Digits Addenda DISABLE Pro CMD : 0401060 Pro CMD : 0401050 5 Digits Addenda ENABLE 5 Digits Addenda DISABLE Pro CMD : 0401080 Pro CMD : 0401070 UPC/EAN-13 2 Digits Addenda ENABLE Addenda Code 2 Digits Addenda DISABLE Pro
** Code Programming ON (Pro CMD : 0006010) ** Code Programming OFF (Pro CMD : 0006000) Symbologies Set Up – 7 2 Digits Addenda ENABLE UPC-E Addenda Code 2 Digits Addenda DISABLE Pro CMD : 0403060 Pro CMD : 0403050 5 Digits Addenda ENABLE 5 Digits Addenda DISABLE Pro CMD : 0403080 Pro CMD : 0403070 UPC-E Default “0” Do Not Transmit Transmit Pro CMD：0403090 2 Digits Addenda ENABLE Pro CMD：0403100 UPC-A Addenda Code 2 Digits Addenda DISABLE Pro CMD : 0404060 Pro CMD : 0404050 5 Digits Adden
** Code Programming ON (Pro CMD : 0006010) ** Code Programming OFF (Pro CMD : 0006000) TERMINATION STRING SETUP BAR CODES Step 1 STRING# 1 TERMINATION CHAR - CR Pro CMD : 0310000 Step 2 Pro CMD : 0309010 Step3 Pro CMD : 0000160 24
