Skype and Q&A Face book group: ADIMLab 3D Printer ADIMLab 3D Printer Filament using and extrude problem solving 1.feed the filament： （1）Please make sure the front end of the filament is straight： Cut the tip at a sharp angle | | | | | / |/ （2）Press down the extruder plunger： Press the lever lightly. Pressing too far will block the filament.
Skype and Q&A Face book group: ADIMLab 3D Printer （4）Preheat the filament： ①Please use the LCD, “Info screen”press the button，rotate the button and select“Prepare”, Click to confirm： ②In the submenu, rotate to select ’Preheat’ PLA”, Click to confirm： Contact: adimlab@gmail.
Skype and Q&A Face book group: ADIMLab 3D Printer ③In the submenu ，rotate to select “Preheat PLA”， Click to confirm： ④Waiting for the nozzle temperature to reach the preset temperature： （5）Manual extrusion： ①When the nozzle temperature reaches about 195℃，Press down the extruder plunger, will extrude a piece of filament： Contact: adimlab@gmail.
Skype and Q&A Face book group: ADIMLab 3D Printer ②If you could find the filament comes out, it proves you load the filament well, and there is no clog in the hot end system： Common problem during this statement: ① When load the filament, did not press the Press down the extruder plunger：will result the Extruder gear didn’t rotate and lead the filament to the nozzle，and cannot extrude during printing。 ② If not insert filament and push it to the end, also will result the extrude problem, and cannot extrude
Skype and Q&A Face book group: ADIMLab 3D Printer ③ If the hot end is clogged, the extruder won’t extrude the filament, we need to 2. Unloading the filament： （1）Preheat： ①“Info screen”press down the rotate button，and select“Prepare”,click to confirm： ②In the submenu, rotate to selection “Preheat PLA”，and click to confirm： ④ In the submenu, rotate to selection “Preheat PLA”， and click to confirm： Contact: adimlab@gmail.
Skype and Q&A Face book group: ADIMLab 3D Printer ⑤ Waiting for the nozzle temperature to reach the preset temperature： （2）Press down the extruder plunger： （3）Manually extrude a piece of filament： Contact: adimlab@gmail.
Skype and Q&A Face book group: ADIMLab 3D Printer （4）Quickly pull out the filament while pressing down extruder plunger： (Notice：Keep the extruder plunger pressed, quickly pull out the filament, do not pause) Contact: adimlab@gmail.
Skype and Q&A Face book group: ADIMLab 3D Printer 3. Replace filament before printing： （1）Unload previous filament： The operation steps are the same as ’2. Unloading the filament’； （2）load the new filament： The operation steps are the same as’1. loading the filament’； Common problem during this statement: ① No preheating before unplugging filament: causing filament to break or damage the extruder.
Skype and Q&A Face book group: ADIMLab 3D Printer “Info screen”press the button，rotate the button and select“Change filament”,click to confirm： （2）The printing will pause to wait，the Extruder system will move to the left-behand position: （3）press the extruder plunger down： Contact: adimlab@gmail.
Skype and Q&A Face book group: ADIMLab 3D Printer （4）press out a piece of filament manually： （5）Quickly pull out the filament while pressing down the plunger： (Notice：Keep the extruder plunger pressed, quickly pull out the filament, do not pause) Contact: adimlab@gmail.
Skype and Q&A Face book group: ADIMLab 3D Printer （6）press down the extruder plunger again: （7）reload the filament, and push it to the bottom： Contact: adimlab@gmail.
Skype and Q&A Face book group: ADIMLab 3D Printer （8）click the rotate button of the LCD： （9）then the Extruder will extrude some filament： （10）Click the “Continue”menu： Contact: adimlab@gmail.
Skype and Q&A Face book group: ADIMLab 3D Printer (11)finish the changing filament, Extruder willcome back to the previous printing position and continue： Method 2： （1）Pause the printing： “Info screen”press down the button，rotate to select“Pause print”,Click to confirm： Contact: adimlab@gmail.
Skype and Q&A Face book group: ADIMLab 3D Printer If you use the old version marlin, the extruder will stop at the Current print position, And leave some molten filament here ，so, we recommend you pause When printing the fill position ； the new marlin add the advanced pause function, to move the nozzle to the LEFT-BEHAND position to prevent the high temp nozzle damage. （2）press the extruder plunger down： （3）press out a piece of filament manually： Contact: adimlab@gmail.
Skype and Q&A Face book group: ADIMLab 3D Printer （4）Quickly pull out the filament while pressing down the plunger： (Notice ：Keep the extruder plunger pressed, quickly pull out the filament, do not pause) Contact: adimlab@gmail.
Skype and Q&A Face book group: ADIMLab 3D Printer （5）press down the extruder plunger again: （6）reload the filament, and push it to the bottom, and make sure you can see the filament come out： （7）“Info screen”press down the button，rotate to select“Resume print”,and click to confirm： Contact: adimlab@gmail.
Skype and Q&A Face book group: ADIMLab 3D Printer （8）if you use the old version marlin, will start printing from the current printing position； If you use the new version marlin, the extruder will extrude some filament first： （9）Click“Continue”menu： Contact: adimlab@gmail.
Skype and Q&A Face book group: ADIMLab 3D Printer （10）the Extruder come back to the previous printing position，continue printing： 5.Test printing： （Please refer to the instruction in the SD card: “ADIMLab Assembly specifications”the 4th and 5th chapters in the directory of“2.Assembly specifications”） （1） Common problems： ① The first layer does not stick to the print surface This is by far the most common 3D printing problem, and probably the first one you may encounter.
Skype and Q&A Face book group: ADIMLab 3D Printer Prepare the print surface – Keep the surface free of grease. Otherwise, your first layer will have a difficulty sticking to the print bed. Before starting any of your prints from ABS, PLA and many other materials, simply wipe the print surface clean with IPA 90%+. Also, you should use Acetone from time to time, when prints stop sticking – but do not use it on daily basis.
Skype and Q&A Face book group: ADIMLab 3D Printer Please refer to this article to get more problem solution: https://www.prusaprinters.org/how-to-fix-the-most-common-3d-printing-errors/ 6.How to solve the problem of the extruder not working： （1）didn’t push the filament to the bottom： phenomenon：The extruder gear is rotating, but there is no filament get out. solution：Insert filament and push it to the end, the insert length is about 90mm.
Skype and Q&A Face book group: ADIMLab 3D Printer solution：Check if the filaments are smooth and rearranged. ② The extruder fan not rotate, the throat heat up and result in the clog of the Teflon tube inside the throat, the extruder will makes a "squeaky" sound. solution：check if the extruder fan is working. Please make sure it’s always on.
Skype and Q&A Face book group: ADIMLab 3D Printer d. if still can’t clean the nozzle well, please refer to: https://www.facebook.com/groups/1235236596606278/permalink/130218123 3245147/?__xts__[0]=68.
Skype and Q&A Face book group: ADIMLab 3D Printer （4）nozzle temp can’t heat up well： ①the heater can’t heat up, or there is no value for the LCD. solution： a. Check if the heater and sensor fasten well in the hot end hole. b. measure the resistance of the heater bar(about 14.5Ω) and the thermal thensor(about 15kΩ). c. if there is no problem, please check the voltage of the heater port, it should be about 24V. Contact: adimlab@gmail.
