User manual

ManualsBrandsADJ ManualsFlood LightInnoColor Beam12

User Instructions

Inno Color Beam 12 Introduction

©American DJ Supply® - www.americandj.com - Inno Color Beam 12 User Manual Page 2

8/12

Unpacking: Thank you for purchasing the Inno Color Beam 12 by

American DJ®. Every Inno Color Beam 12 has been thoroughly tested

and has been shipped in perfect operating condition. Carefully check

the shipping carton for damage that may have occurred during ship-

ping. If the carton appears to be damaged, carefully inspect your x-

ture for any damage and be sure all accessories necessary to operate

the unit has arrived intact. In the case damage has been found or parts

are missing, please contact our toll free customer support number for

further instructions. Do not return this unit to your dealer without rst

contacting customer support.

Introduction: The Inno Color Beam 12 is part of American DJ’s con-

tinuing pursuit for creating high quality affordable intelligent fixtures.

The Inno Color Beam 12 is a compact, high performance, DMX intel-

ligent, moving head, LED fixture. This fixture is a great piece for retail

stores, displays, mood, architectural, interior and exterior decoration,

and clubs. This unit can be used as a stand alone, or in a Master/Slave

conguration. The unit can also be controlled via DMX controller.

Customer Support: American DJ® provides a toll free customer sup-

port line, to provide set up help and to answer any question should you

encounter problems during your set up or initial operation. You may

also visit us on the web at www.americandj.com for any comments or

suggestions. Service Hours are Monday through Friday 8:00 a.m. to

4:30 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: support@americandj.com

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

American DJ®.

PLEASE recycle the shipping carton when ever possible.

InnoColor

Beam12

Summary of content (10 pages)

PAGE 1
Inno Color Beam 12 Introduction Unpacking: Thank you for purchasing the Inno Color Beam 12 by InnoColor Beam12 American DJ®. Every Inno Color Beam 12 has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all accessories necessary to operate the unit has arrived intact.
PAGE 2
Inno Color Beam 12 General Instructions To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations of this unit. These instructions contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the unit, for future reference.
PAGE 3
POWER Inno Color Beam 12 Set Up Inno Color Beam 12 Notice: Be sure to follow figures two and three when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior. DMX-512: DMX is short for Digital Multiplex.
PAGE 4
Inno Color Beam 12 System Menu Inno Color Beam 12 System Menu ADDR - DMX Address Setting via control board - 1. Press the MENU button until “ADDR” is displayed, press ENTER. 2. “X” will now be displayed, “X” represents the displayed address. Press the UP or DOWN buttons to find your desired address. 3. Press ENTER to confirm, then connect your DMX controller. NOTE: If after you connect your DMX controller the unit does not fall into DMX mode, press and hold the MENU button for at least 3 seconds.
PAGE 5
Inno Color Beam 12 System Menu Inno Color Beam 12 System Menu 2. “SH X” will now be displayed, “X” representing a number between 0-4. Shows 1-4 are preset shows, while “SH 0” is random show. Press the UP or DOWN buttons to find your desired show. unit will automatically go into the last DMX set up. 3. Once you have found your desired show press ENTER, and then press and hold the MENU button for at least 3 seconds to confirm.
PAGE 6
Inno Color Beam 12 System Menu Inno Color Beam 12 System Menu 2. When “DISP” is displayed the LED display will remain normal, when “DSIP” is displayed, the LED display will be “flipped”. Press the ENTER button to set your desired . TEDT - With this function you can check the LED tempera- BALA - With this function you are able to adjust the RGB colors to create your desired shade of white. 2. The LED temperature will now be displayed. Press MENU to exit. 1.
PAGE 7
Inno Color Beam 12 Universal DMX Control Universal DMX Control: This function allows you to use a Elation® universal DMX-512 controller to control the chases and patterns, dimmer and strobe. A DMX controller allows you to create unique programs tailored to your individual needs. The Inno Color Beam 12 has 2 DMX channel modes; a 9 Channel Mode & 16 Channel Mode. To select your channel mode see page 8. 1.
PAGE 8
Inno Color Beam 12 Channel 1 2 3 4 5 6 7 8 Value 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 15 16 - 35 36 - 55 56 - 75 76 - 95 96 - 115 116 - 135 136 - 155 156 - 175 176 - 195 196 - 215 216 - 235 236 - 255 0 - 255 0 - 69 70 - 79 80 - 89 9 ©American 90 - 199 200 - 209 210 - 239 240 - 255 0 - 255 16 Channel Mode Function PAN 0° - 540° PAN FINE TILT 0° - 270° TILT FINE PAN/TILT SPEED FAST - SLOW PAN/TILT MACROS STOP MACRO 1 MACRO 2 MACRO 3 MACRO 4 MACRO 5 MACRO 6 MACRO 7 MACRO 8 MACRO 9 MACRO 10 MAC
PAGE 9
Inno Color Beam 12 Photometric Chart Inno Color Beam 12 Fuse Replacement Locate and remove the unit’s power cord. Once the cord has been removed located the fuse holder located inside the power socket. Insert a flat-head screw driver into the power socket and gently pry out the fuse holder. Remove the bad fuse and replace with a new one. The fuse holder has a built-in socket for a spare fuse be sure not to confuse the spare fuse with active fuse.
PAGE 10
Inno Color Beam 12 Warranty MANUFACTURER’S LIMITED WARRANTY A. American DJ, Inc. hereby warrants, to the original purchaser, American DJ and American Audio products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories.