User manual

©American DJ Supply® - www.americandj.com - Inno Color Beam 12 User Manual Page 14©American DJ Supply® - www.americandj.com - Inno Color Beam 12 User Manual Page 13
Universal DMX Control: This function allows you to use a Elation®
universal DMX-512 controller to control the chases and patterns,
dimmer and strobe. A DMX controller allows you to create unique
programs tailored to your individual needs. The Inno Color Beam 12
has 2 DMX channel modes; a 9 Channel Mode & 16 Channel Mode.
To select your channel mode see page 8.
1. This function will allow you to control each individual fixture’s
traits with a standard DMX 512 controller such as the
Elation® Show Designer™ or the Elation® DMX Operator.™ See
pages 14-16 for the DMX modes & traits.
2. To run your fixture in DMX mode, select your desired channel
mode and then set your desired DMX address following the
directions on page 8, and the set-up specifications that come
with your DMX controller.
3. Plug in the fixture via the XLR connections to any standard DMX
controller.
4. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.
Inno Color Beam 12 Universal DMX Control
Master-Slave Conguration: This function will allow you to link up
to 16 units together and operate without a controller. The units will be
sound activated. In Master-Slave operation one unit will act as the con-
trolling unit and the others will react to the controlling units programs.
Any unit can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The rst unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.
2. Set the Master unit to your desired operating mode.
3. On the slave units tap the MENU button until “Slave Mode” is dis-
played, and Press ENTER. Choose either “Slave 1” or “Slave 2”
and press ENTER. See page 9 for more info.
4. The slave units will now follow the Master unit.
Inno Color Beam 12 Master-Slave Configuration
Channel Value Function
1 0 - 255 PAN 0° - 540°
2 0 - 255 TILT 0° - 270°
3 SHUTTER/STROBING
0 - 7 BLACKOUT
8 - 15 OPEN
16 - 131 STROBING SLOW - FAST
132 - 139 OPEN
140 - 181 SLOW OPEN - FAST CLOSE
182 - 189 OPEN
190 - 231 SLOW CLOSE - FAST OPEN
232 - 239 OPEN
240 - 247 RANDOM STROBE
2 4 8 - 2 5 5 O P E N
4 RED
0 - 255 0% - 100%
5 GREEN
0 - 255 0% - 100%
6 BLUE
0 - 255 0% - 100%
7 WHITE
0 - 255 0% - 100%
8 MASTER DIMMER
0 - 255 0% - 100%
9 SPECIAL FUNCTIONS
0 - 69 NO FUNCTION
70 - 79 ENABLE BLACKOUT WHILE PAN OR
TILT MOVEMENT
80 - 89 DISABLE BLACKOUT WHILE PAN OR
TILT MOVEMENT
90 - 199 NO FUNCTION
200 - 209 RESET
210 - 239 NO FUNCTION
240 - 255 SOUND ACTIVE
Inno Color Beam 12 9 Channel Mode