Manual

ManualsBrandsADJ ManualsDMX Lighting Control DesksControl Device

User Instructions

SCENE SETTER

™

DMX-512

MIDI

CAPABLE

CONTROLS & FUNCTIONS

1. PRESET A LED’S: Will indicate the activity for sliders 1 - 12.

2. CHANNEL FADERS 1 - 12: Slide the faders to adjust the DMX output (from 0 to 255) or

fixture intensity (from 0% to 100%).

3. FLASH 1- 12: Press to momentary activate maximum channel output.

4. PRESET B LED’S: Will indicate the activity for sliders 13 - 24.

SCENE LED’S: When lit will indicate which scene or scenes are activated.

6. CHANNEL FADERS 13 -24: Slide the faders to adjust the DMX output (from 0 to 255) or

fixture intensity (from 0% to 100%).

FLASH 13 -24: Press to momentary activate maximum channel output.

8. DARK: Press to momentarily black out all output including FULL, FLASH and Programs.

9. DOWN / BEAT REV: The DOWN function is used to modify a scene in the EDIT MODE;

BEAT REV is used to reverse the chasing direction of a SCENE program with regular

beat.

10. MODE SELECT / REC SPEED: Press to select the desired operating mode CHASE

SCENE/ DOUBLE PRESET / SINGLE PRESET, the corresponding LED’S light up to indicate

function.

11.UP/CHASE REV: The UP function is used to modify a scene in the EDIT MODE; CHASE

REV is used to reverse the chasing direction of a SCENE program with speed control.

Specifications are subject to change without notice! - Scene Setter User Manual page 1

11 18151412 138

9 10

30292827262524 22

Summary of content (9 pages)

PAGE 1
User Instructions SCENE SETTER™ 1 2 3 MIDI CAPABLE 8 9 DMX-512 10 11 12 13 14 15 18 17 18 19 20 21 4 5 6 7 23 24 25 26 27 28 29 30 31 22 CONTROLS & FUNCTIONS 1. PRESET A LED’S: Will indicate the activity for sliders 1 - 12. 2. CHANNEL FADERS 1 - 12: Slide the faders to adjust the DMX output (from 0 to 255) or fixture intensity (from 0% to 100%). 3. FLASH 1- 12: Press to momentary activate maximum channel output. 4. PRESET B LED’S: Will indicate the activity for sliders 13 - 24. 5.
PAGE 2
12. PAGE SELECT: Press to change between pages of scenes. 13. DELETE REV ONE: Press and hold this button then press any FLASH 13 -24 to reverse direction of Scene that is running. 14. EXIT: Press to select ADD or KILL mode 15. INSERT / % OR 0-255: Press to select LCD DISPLAY 16. RECORD: Press to record output step by step. 17. EXIT / ALL REV: Press to reverse chasing direction of programs 18. PARK: In CHASE SCENE mode press to select SINGLE or MIX mode 19. HOLD: Press to maintain all output. 20.
PAGE 3
BASIC OPERATING INSTRUCTIONS Record Enable 1. Press and hold down the RECORD BUTTON (FIG. 16) 2. While holding down the RECORD BUTTON press bumpers 1, 6, 6, and 8 (FIG. 3) in sequence. 3. Release the RECORD BUTTON (FIG. 16) - The Record LED should light up. Exit Record 1. Press and hold down the RECORD BUTTON (FIG. 16). 2. While holding down the RECORD BUTTON (FIG. 16) press and release the REC EXIT BUTTON (FIG.14) 3. Release the RECORD BUTTON (Fig.16), Erase All Programs 1.
PAGE 4
RUNNING SCENES 1. After all your programming is complete, you may run your program. 2. Using the MODE SELECT BUTTON (FIG. 10) select ‘CHNS SCENES’. 3. Turn the slider, for the appropriate flash button the scene was recorded, to the maximum or 10 position. The yellow scene LED should light and all green LED’S for the corresponding sliders that were programmed into that scene. DELETE PROGRAM 1. Enter the record mode (SEE RECORD ENABLE ON PAGE 2). 2. Use the PAGE BUTTON (FIG.
PAGE 5
4. Continue steps 2, 3, and 4 until all the desired steps have been modified. Exit Edit Mode: 1. Press and hold the RECORD BUTTON (FIG. 16). 2. While Holding down the RECORD BUTTON (FIG. 16) press and release the REC EXIT BUTTON (FIG. 14). 3. Release the RECORD BUTTON (FIG. 16). SELECT AND RUNNING PROGRAMS Running programs: 1. To run a program; press the MODE SELECT BUTTON (FIG. 10) and select ‘CHNS SCENES,’ this will be indicated by a red led. 2. Press the PAGE BUTTON (FIG.
PAGE 6
Running A Program With The Speed Slider: 1. Be sure the audio is disengaged. The AUDIO BUTTON (FIG. 20), green led should be turned off. The MODE SELECT BUTTON (FIG.10) must be in ‘CHNS SCENES’ to controll the audio mode. 2. Press the MODE SELECT BUTTON (FIG.10) and select ‘CHNS SCENES.’ 3. Press the PARK BUTTON (FIG. 18) to select MIX CHASE MODE. A yellow LED will indicate this selection. 4. Select your program as described on page 5. 5. Slide the SPEED SLIDER (FIG.
PAGE 7
Setting MIDI OUT: 1. Press and hold the RECORD BUTTON (FIG. 16). 2. While holding down the RECORD BUTTON (FIG. 16), tap the number two FLASH BUTTON (FIG. 3) three time. 3. Release the RECORD BUTTON (FIG. 16). 4. ‘Ch0’ should appear in the DIGITAL DISPLAY (FIG. 13A) indicating MIDI OUT is available. 5. Press the corresponding FLASH BUTTON (FIG. 7) you wish to assign MIDI OUT, its LED will light indicating MIDI OUT is available. Turning off MIDI Settings: 1. Press and hold the RECORD BUTTON (FIG. 16). 2.
PAGE 8
FUNCTIONS: Fade Time: 1. The amount of time it will take for the dimmer to go from zero output to maximum output or the amount of time it will take for the DMX signal to go from zero to 255, and vice verse. 2. Fade time is adjusted through the FADE SLIDER (FIG. 28), which varies from instant to 10 minutes. SINGLE MODE (FIG.18): 1. 2. 3. 4. All programs will run in sequential order starting with program one. The DIGITAL DISPLAY (FIG. 13A) will display the running program number.
PAGE 9
Fade Time and Speed Indicators: 1. When a program is running at a time more than 1 minute the LCD display will indicate two decimal points: EXAMPLE: 1 AND 15 SECONDS WILL DISPLAY AS 1.15 10 MINUTES WILL DISPLAY AS 10.0 2. When a program is running at a time under 1 minute the LCD display will indicate only one decimal points: EXAMPLE: 11 AND 1/2 SECONDS WILL DISPLAY AS 11.5 1/10 OF A SECOND WILL DISPLAY AS 0.